Are Multiple Cryoprobes Additive or Synergistic in Renal Cryotherapy?

OBJECTIVE To investigate the relationship between multiple cryoprobes was investigated to determine whether they work in an additive or synergistic fashion in an in vivo animal model because 1.47 mm (17-gauge) cryoprobes have been introduced to the armamentarium for renal cryotherapy. METHODS Laparoscopic-guided percutaneous cryoablation was performed in both renal poles of 3 pigs using 3 IceRod cryoprobes. These 12 cryolesions were compared with 12 cryolesions using a single IceRod cryoprobe. Each cycle consisted of two 10-minute freeze cycles separated by a 5-minute thaw. The iceball volume was measured using intraoperative ultrasonography. The kidneys were harvested, and cryolesion surface area was calculated. The lesions were fixed and excised to obtain a volume measurement. Statistical analysis was used to compare the single probe results multiplied by 3 to the multiple probe group for iceball volume, cryolesion surface area, and cryolesion volume. RESULTS The iceball volume for the first freeze cycle for the single cryoprobe multiplied by 3 was 8.55 cm(3) compared with 9.79 cm(3) for the multiple cryoprobe group (P = .44) and 10.01 cm(3) versus 16.58 cm(3) for the second freeze (P = .03). The cryolesion volume for the single cryoprobe multiplied by 3 was 11.29 cm(3) versus 14.75 cm(3) for the multiple cyroprobe group (P = .06). The gross cryolesion surface area for the single cryoprobe multiplied by 3 was 13.14 cm(2) versus 13.89 cm(2) for the multiple probe group (P = .52). CONCLUSION The cryolesion created by 3 simultaneously activated 1.47-mm probes appears to be larger than that of an additive effect. The lesions were significantly larger as measured by ultrasonography and nearly so (P = .06) as measured by the gross cryolesion volume. UROLOGY 79: 484.e1-484.e6, 2012. (c) 2012 Elsevier Inc. All rights reserved.

Variability of physicochemical properties of an epoxy resin sealer taken from different parts of the same tube

Baldi JV, Bernardes RA, Duarte MAH, Ordinola-Zapata R, Cavenago BC, Moraes JCS, de Moraes IG. Variability of physicochemical properties of an epoxy resin sealer taken from different parts of the same tube. International Endodontic Journal,similar to 45, 915920, 2012. Abstract Aim To analyse several physicochemical properties of AH Plus (Dentsply DeTrey, Konstanz, Germany), including setting time, flow, radiopacity and the degree of conversion (DC); and to correlate the results with the source of the material: from the beginning, middle or end of the tubes in which they were supplied. Methodology Three experimental groups were established for each property investigated. Group 1 corresponded to material taken from the beginning of tubes A and B; Group 2 corresponded to material taken from the middle of each tube; and group 3 corresponded to that from the end of each tube. The setting time, flow and radiopacity were studied according to American National Standards Institute/American Dental Association (ANSI/ADA) Specification 57. DC was determined from infrared spectra, which were recorded at 1-h intervals for the first 6 h; then, at 2-h intervals for the next 14 h; then, at 24 and 30 h. Data were analysed statistically by analysis of variance (anova), TukeyKramer, KruskalWallis and Dunn tests, with a significance level of 5%. Results Group 1 had a significantly longer setting time (2303 +/- 1058 min) (P < 0.05). Group 3 had the lowest flowability (30.0 +/- 0.7 mm) and the highest radiopacity (14.85 +/- 1.8 mm Al) (P < 0.05). No differences were found for the DC test (P > 0.05). Conclusion The results suggest that segregation occurs between the organic and inorganic components of AH Plus sealer, thereby changing the setting time, flow and radiopacity.

Nutrients and Nonessential Elements in Soil after 11 Years of Wastewater Irrigation

Irrigation of citrus (Citrus aurantium L. x Citrus paradise Macf.) with urban reclaimed wastewater (RWW) can be economical and conserve fresh water. However, concerns remain regarding its deleterious effects on soil quality. We investigated the ionic speciation (ISP) of RWW and potential impacts of 11 yr of irrigation with RWW on soil quality, compared with well-water (WW) irrigation. Most of nutrients (similar to 53-99%) in RWW are free ionic species and readily available for plant uptake, such as: NH4+, NO3-, K+, Ca2+, Mg2+, SO42-, H3BO3, Cl-, Fe2+, Mn2+, Zn2+, Co2+, and Ni2+, whereas more than about 80% of Cu, Cr, Pb, and Al are complexed with CO3-, OH-, and/or organic matter. The RWW irrigation increased the availability and total concentrations of nutrients and nonessential elements, and soil salinity and sodicity by two to three times compared with WW-irrigated soils. Although RWW irrigation changed many soil parameters, no difference in citrus yield was observed. The risk of negative impacts from RWW irrigation on soil quality appears to be minimal because of: (i) adequate quality of RWW, according to USEPA limits; (ii) low concentrations of metals in soil after 11 yr of irrigation with RWW; and (iii) rapid leaching of salts in RWW-irrigated soil during the rainy season.

U-Pb zircon ages of orthogneisses and supracrustal rocks of the Cariris Velhos belt: Onset of Neoproterozoic rifting in the Borborema Province, NE Brazil

New geochronological and geochemical constraints on Precambrian sedimentary and volcanic successions exposed in the western part of the Central Domain of the Borborema Province, NE Brazil, indicate the presence of two distinct tectono-stratigraphic complexes: Riacho Gravata and Sao Caetano. Both complexes and associated orthogneisses are referred in the literature as the Cariris Velhos belt, having depositional, extrusive, or intrusive ages within the interval 985-913 Ma. The Riacho Gravata complex consists of bimodal (but mostly felsic) volcanic and volcanoclastic rocks, muscovite+/-graphite schists, quartzites, and marble with local occurrences of banded-iron-formation. The Sao Caetano complex mainly consists of metagreywackes, marbles, calc-silicate rocks, and rare meta-mafic rocks. Meta-mafic rocks from both complexes have geochemical signatures similar to those of continental flood basalts, with epsilon Nd (1.0 Ga) values ranging from -1.0 to -2.8. Felsic volcanic rocks from the Riacho Gravata complex show epsilon Nd (1.0 Ga) values ranging from -1.0 to -7.4 and geochemical signatures similar to A(2)-type granitoids. New SHRIMP U-Pb zircon data from felsic volcanic rocks within the Riacho Gravata complex yielded ages of 1091 +/- 13 Ma and 996 +/- 13 Ma. In contrast, meta-graywackes from the Sao Caetano complex show a maximum deposition age of ca. 806 Ma in the northern part and ca. 862 Ma in the southern part of the outcrop area. The orthogneisses show epsilon Nd (1.0 Ga) values ranging from 1.0 to -4.2 with U/Pb TIMS and SHRIMP ages ranging from 960 to 926 Ma and geochemical signatures of A(2)-type granitoids. The data reported in this paper suggest at least two periods of extension within the Central Domain of the Borborema Province, the first starts ca. 1091 Ma with magmatism and deposition, creating the Riacho Gravata basin and continued intrusion of A-type granites to 920 Ma. A second rift event, which reactivated old faults, generated a basin with a maximum deposition age of ca. 806 Ma. Furthermore, the oldest granitoids cutting these metasedimentary rocks have crystallization ages of ca. 600 Ma. This suggests that the second rift event could be early Brasiliano in age. The resulting Sao Caetano basin received detritus from a variety of sources, although detritus from the Riacho Gravata complex dominated. Deposition ages of the Riacho Gravata and the Sao Caetano complexes are coeval with deposits in other basins of the Borborema Province (Riacho do Tigre in the Central Domain; Macurure and Maranco in the Sergipano Belt of the Southern domain). The Macaubas Group from SE Brazil and its counterparts in Africa, the Zadanian and Mayumbian Groups, in the western edge of the Congo Craton are also coeval. Closure of the Riacho Gravata and Sao Caetano basins occurred during the Brasiliano convergence (705-600 Ma). During the last stage of convergence, ca. 612 Ma, pull-apart basins were created and filled; final basin closure took place 605-592 Ma, after deposition ceased. (C) 2011 Elsevier B.V. All rights reserved.

Marine natural products: chemical and biological potential of seaweeds and their endophytic fungi

Marine natural products have currently been recognized as the most promising source of bioactive substances for drug discovery research. In this review, extraordinary metabolites from marine algae species are illustrated, as well as approaches for their isolation and determination of their biological properties and pharmaceutical potential. Furthermore, marine endophytic microorganisms (from marine algae) are presented as a new subject for extensive investigation to find novel natural products, which make them a potentially rich and innovative source for new drug candidates.

Structure and peroxidase activity of ferric Streptomyces clavuligerus orf10-encoded protein P450CLA: UV-visible, CD, MCD and EPR spectroscopic characterization

The present study reports the spectroscopic characterization by UV-visible absorption spectroscopy, magnetic circular dichroism (MCD) and electron paramagnetic resonance (EPR) of the recombinant orf10-encoded P450-camphor like protein (P450CLA)of Streptomyces clavuligerus expressed in Escherichia coli Rosetta in the native form and associated to external ligands containing the β-lactam, oxazole and alkylamine-derived (alcohol) moieties of the clavulamic acid. Considering the diversity of potential applications for the enzyme, the reactivity with tert-butylhydroperoxide (tert-BuOOH) was also characterized. P450CLA presents a covalently bound heme group and exhibited the UV-visible, CD and MCD spectral features of P450CAM including the fingerprint Soret band at 450 nm generated by the ferrous CO-complex. P450CLA was converted to high valence species by tert-BuOOH and promoted homolytic scission of the O-O bond. The radical profile of the reaction was tert-butyloxyl as primary and methyl and butylperoxyl as secondary radicals. The secondary methyl and butylperoxyl radicals resulted respectively from the β-scission of the alkoxyl radical and from the reaction of methyl radical with molecular oxygen.

Time lags of the kilohertz quasi-periodic oscillations in the low-mass X-ray binaries 4U 1608−52 and 4U 1636−53

We studied the energy and frequency dependence of the Fourier time lags and intrinsic coherence of the kilohertz quasi-periodic oscillations (kHz QPOs) in the neutron-star lowmass X-ray binaries 4U 1608−52 and 4U 1636−53, using a large data set obtained with the Rossi X-ray Timing Explorer. We confirmed that, in both sources, the time lags of the lower kHz QPO are soft and their magnitude increases with energy. We also found that: (i) In 4U 1636−53, the soft lags of the lower kHz QPO remain constant at∼30 μs in the QPO frequency range 500–850 Hz, and decrease to ∼10 μs when the QPO frequency increases further. In 4U 1608−52, the soft lags of the lower kHz QPO remain constant at 40 μs up to 800 Hz, the highest frequency reached by this QPO in our data. (ii) In both sources, the time lags of the upper kHz QPO are hard, independent of energy or frequency and inconsistent with the soft lags of the lower kHz QPO. (iii) In both sources the intrinsic coherence of the lower kHz QPO remains constant at ∼0.6 between 5 and 12 keV, and drops to zero above that energy. The intrinsic coherence of the upper kHz QPO is consistent with being zero across the full energy range. (iv) In 4U 1636−53, the intrinsic coherence of the lower kHz QPO increases from ∼0 at ∼600 Hz to ∼1, and it decreases to ∼0.5 at 920 Hz; in 4U 1608−52, the intrinsic coherence is consistent with the same trend. (v) In both sources the intrinsic coherence of the upper kHz QPO is consistent with zero over the full frequency range of the QPO, except in 4U 1636−53 between 700 and 900 Hz where the intrinsic coherence marginally increases. We discuss our results in the context of scenarios in which the soft lags are either due to reflection off the accretion disc or up-/down-scattering in a hot medium close to the neutron star. We finally explore the connection between, on one hand the time lags and the intrinsic coherence of the kHz QPOs, and on the other the QPOs’ amplitude and quality factor in these two sources.

Models and methods for power monolithic microwave integrated circuits

Computer aided design of Monolithic Microwave Integrated Circuits (MMICs) depends critically on active device models that are accurate, computationally efficient, and easily extracted from measurements or device simulators. Empirical models of active electron devices, which are based on actual device measurements, do not provide a detailed description of the electron device physics. However they are numerically efficient and quite accurate. These characteristics make them very suitable for MMIC design in the framework of commercially available CAD tools. In the empirical model formulation it is very important to separate linear memory effects (parasitic effects) from the nonlinear effects (intrinsic effects). Thus an empirical active device model is generally described by an extrinsic linear part which accounts for the parasitic passive structures connecting the nonlinear intrinsic electron device to the external world. An important task circuit designers deal with is evaluating the ultimate potential of a device for specific applications. In fact once the technology has been selected, the designer would choose the best device for the particular application and the best device for the different blocks composing the overall MMIC. Thus in order to accurately reproducing the behaviour of different-in-size devices, good scalability properties of the model are necessarily required. Another important aspect of empirical modelling of electron devices is the mathematical (or equivalent circuit) description of the nonlinearities inherently associated with the intrinsic device. Once the model has been defined, the proper measurements for the characterization of the device are performed in order to identify the model. Hence, the correct measurement of the device nonlinear characteristics (in the device characterization phase) and their reconstruction (in the identification or even simulation phase) are two of the more important aspects of empirical modelling. This thesis presents an original contribution to nonlinear electron device empirical modelling treating the issues of model scalability and reconstruction of the device nonlinear characteristics. The scalability of an empirical model strictly depends on the scalability of the linear extrinsic parasitic network, which should possibly maintain the link between technological process parameters and the corresponding device electrical response. Since lumped parasitic networks, together with simple linear scaling rules, cannot provide accurate scalable models, either complicate technology-dependent scaling rules or computationally inefficient distributed models are available in literature. This thesis shows how the above mentioned problems can be avoided through the use of commercially available electromagnetic (EM) simulators. They enable the actual device geometry and material stratification, as well as losses in the dielectrics and electrodes, to be taken into account for any given device structure and size, providing an accurate description of the parasitic effects which occur in the device passive structure. It is shown how the electron device behaviour can be described as an equivalent two-port intrinsic nonlinear block connected to a linear distributed four-port passive parasitic network, which is identified by means of the EM simulation of the device layout, allowing for better frequency extrapolation and scalability properties than conventional empirical models. Concerning the issue of the reconstruction of the nonlinear electron device characteristics, a data approximation algorithm has been developed for the exploitation in the framework of empirical table look-up nonlinear models. Such an approach is based on the strong analogy between timedomain signal reconstruction from a set of samples and the continuous approximation of device nonlinear characteristics on the basis of a finite grid of measurements. According to this criterion, nonlinear empirical device modelling can be carried out by using, in the sampled voltage domain, typical methods of the time-domain sampling theory.

Tecnologie sostenibili per il social housing

“Tecnologie sostenibili per il social housing”: la mia tesi affronta il tema dell’edilizia sociale cercando di capire se può ancora diventare un campo di ricerca e sperimentazione architettonica come lo è stato in più occasioni nell’ultimo secolo. La ricerca si è sviluppata in due fasi: una prima attività di studio della vicenda storica dell’abitazione sociale in Italia, con alcuni confronti europei, fino ad analizzare il nuovo quadro che si è andato delineando dalla fine degli anni ’90 e che caratterizza la situazione attuale. Successivamente, la progettazione di un piccolo intervento di edilizia abitativa che si propone di rispondere agli attuali profili della domanda, puntando a scelte tipologiche e costruttive coerenti. Nel trentennio 1950-’80, nell’Europa uscita dalla Seconda guerra mondiale, e in Italia in particolare, l’edilizia popolare ha vissuto un periodo dinamico, ricco di interventi normativi da parte dello Stato, (su tutte la legge Fanfani, e le norme Gescal) che hanno permesso di realizzare molti degli edifici ancora oggi utilizzati, accelerando la ripresa economica e sociale. Dopo gli anni ’80, le ricerche e le sperimentazioni in campo architettonico si spostano verso altri temi; superata la necessità di fornire una casa a milioni di persone, il tema dell’alloggio sembra perdere il forte rilievo sociale che aveva avuto nei decenni precedenti. Fino a ritenere che il tema dell’alloggio e in particolare dell’alloggio sociale, non avesse più la necessità di essere sperimentato e approfondito. Oggi la situazione riguardante la sperimentazione non è molto diversa: sono ancora molto limitati, infatti, gli studi e le ricerche sul tema dell’alloggio sociale. Ciò che è nuovamente mutata, invece, è l’emergenza di una nuova domanda di casa e la drammatica esigenza sociale di fornire un alloggio a milioni di famiglie che non se lo possono permettere. Le dinamiche che guidano questa nuova ondata di richiesta di alloggi sono molteplici, sia di natura sociale che economica. Sul piano sociale: - l’aumento del numero delle famiglie, passate da 22.226.000 nel 200o a 24.642.000 nel 2010, con un aumento del 9,8% in un solo decennio; - la “nuclearizzazione” delle famiglie e la loro contrazione dimensionale, fino agli attuali 2,4 componenti per nucleo; - l’invecchiamento della popolazione; - l’aumento della popolazione straniera, con oltre 3.900.000 di immigrati regolari. Su quello economico: - l’aumento della povertà assoluta: in Italia 1.162.000 famiglie (4,7%) corrispondenti a 3.074.000 individui vivono sotto la soglia di povertà; - l’aumento della povertà relativa, che investe oggi 2.657.000 famiglie (9,3%) e l’aumento delle famiglie a rischio di povertà (920.000 famiglie, pari al 3,7% dei nuclei). Questi dati evidenziano la dimensione del problema abitativo e smentiscono l’opinione che si tratti di una questione marginale: nel 2010 in Italia almeno 1.162.000 non hanno le risorse per pagare un affitto, nemmeno a canone agevolato, e 4.739.000 famiglie non riescono a pagare un affitto ai prezzi del libero mercato, ma non hanno la possibilità di entrare nelle graduatorie per l’assegnazione di un alloggio sociale. Da questa panoramica sulle dimensioni del disagio abitativo, prende spunto la progettazione del mio sistema costruttivo, che si pone come obiettivo quello di ridurre i costi di costruzione tramite la standardizzazione dei componenti, consentendo di conseguenza, un minor costo di costruzione e quindi la possibilità di canoni di affitto ridotti, mantenendo buoni standard di qualità degli alloggi, sostenibilità ambientale e risparmio energetico. Le linee guida che hanno portato alla progettazione del sistema sono: - modularità degli spazi abitativi - zonizzazione funzionale - razionalizzazione impiantistica - illuminazione naturale - industrializzazione dei sistema costruttivo - standardizzazione dei componenti. Il risultato è un catalogo di alloggi di diverse metrature, aggregabili secondo tre tipologie residenziali. - a ballatoio - in linea - a torre Messo a punto questo sistema costruttivo, è stato progettato un intervento in un contesto specifico, per verificare l’applicabilità delle soluzioni sviluppate ed esplorarne alcune possibilità.

Charakterisierung von apoFNR, einer weiteren Form des Sauerstoffsensors FNR aus Escherichia coli und von NreB, einem potentiellen Sauerstoffsensor aus Staphylococcus carnosus

FNR (Fumarat Nitratreduktase Regulator) ist der Sauerstoffsensor aus Escherichia coli. Bisher waren zwei Formen von FNR bekannt, der aktive Zustand, ein Dimer mit je einem [4Fe4S]-Zentrum und ein inaktiver Zustand, in dem FNR als Monomer mit je einem [2Fe2S]-Zentrum vorliegt. Die Untersuchungen dieser Arbeit geben nun Hinweise, dass es mit apoFNR eine dritte physiologische Form von FNR gibt. Es wurde die Entstehung von apoFNR aus [4Fe4S]•FNR untersucht und die biochemischen Eigenschaften von apoFNR charakterisiert. ApoFNR konnte in vitro zu [4Fe4S]•FNR rekonstituiert werden, hierbei konnte die Lagphase der Rekonstitution durch Zusatz von Glutaredoxinen zum Rekonstitutionsansatz verkürzt werden. FNR, dessen Cysteinreste in vivo unter aeroben bzw. anaeroben Bedingungen mit 4-Acetamido-4´-Maleimidylstilbene-2,2´Disulfonsäure markiert wurden, zeigt auf SDS-Gelen einen Shift zu einer höheren Masse im Vergleich zu unmarkiertem FNR. Allerdings trat in aeroben Zellen eine zusätzliche Bande bei einer niedrigeren Masse auf. Es waren hier also weniger Cysteinreste markierbar. Weiterhin wurde mit NreB ein potentieller Sauerstoffsensor aus Staphylococcus carnosus untersucht. Es wurden Hinweise auf ein Eisen-Schwefel-Zentrum vom FNR-Typ als Cofaktor gefunden. Der Einbau dieses Cofaktors war abhängig von der Anwesenheit der Cysteinreste in NreB, von der Cysteindesulfurase NifSAV und von Eisenionen. Der Cofaktor war sauerstoffempfindlich und beeinflusste die Autophosphorylierung von NreB.