Methodology for identifying parameters for the TRNSYS model Type 210 -wood pellet stoves and boilers

This report describes a method how to perform measurements on boilers and stoves and how to identify parameters from the measurements for the boiler/stove-model TRNSYS Type 210. The model can be used for detailed annual system simulations using TRNSYS. Experience from measurements on three different pellet stoves and four boilers were used to develop this methodology. Recommendations for the set up of measurements are given and the re-quired combustion theory for the data evaluation and data preparation are given. The data evalua-tion showed that the uncertainties are quite large for the measured flue gas flow rate and for boilers and stoves with high fraction of energy going to the water jacket also the calculated heat rate to the room may have large uncertainties. A methodology for the parameter identification process and identified parameters for two different stoves and three boilers are given. Finally the identified models are compared with measured data showing that the model generally agreed well with meas-ured data during both stationary and dynamic conditions.

Emissions from realistic operation of residential wood pellets heating systems

Emissions from residential combustion appliances vary significantly depending on the firing behaviours and combustion conditions, in addition to combustion technologies and fuel quality. Although wood pellet combustion in residential heating boilers is efficient, the combustion conditions during start-up and stop phases are not optimal and produce significantly high emissions such as carbon monoxide and hydrocarbon from incomplete combustion. The emissions from the start-up and stop phases of the pellet boilers are not fully taken into account in test methods for ecolabels which primarily focus on emissions during operation on full load and part load. The objective of the thesis is to investigate the emission characteristics during realistic operation of residential wood pellet boilers in order to identify when the major part of the annual emissions occur. Emissions from four residential wood pellet boilers were measured and characterized for three operating phases (start-up, steady and stop). Emissions from realistic operation of combined solar and wood pellet heating systems was continuously measured to investigate the influence of start-up and stop phases on total annual emissions. Measured emission data from the pellet devices were used to build an emission model to predict the annual emission factors from the dynamic operation of the heating system using the simulation software TRNSYS. Start-up emissions are found to vary with ignition type, supply of air and fuel, and time to complete the phase. Stop emissions are influenced by fan operation characteristics and the cleaning routine. Start-up and stop phases under realistic operation conditions contribute 80 – 95% of annual carbon monoxide (CO) emission, 60 – 90% total hydrocarbon (TOC), 10 – 20% of nitrogen oxides (NO), and 30 – 40% particles emissions. Annual emission factors from realistic operation of tested residential heating system with a top fed wood pelt boiler can be between 190 and 400 mg/MJ for the CO emissions, between 60 and 95 mg/MJ for the NO, between 6 and 25 mg/MJ for the TOC, between 30 and 116 mg/MJ for the particulate matter and between 2x10-13 /MJ and 4x10-13 /MJ for the number of particles. If the boiler has the cleaning sequence with compressed air such as in boiler B2, annual CO emission factor can be up to 550 mg/MJ. Average CO, TOC and particles emissions under realistic annual condition were greater than the limits values of two eco labels. These results highlight the importance of start-up and stop phases in annual emission factors (especially CO and TOC). Since a large or dominating part of the annual emissions in real operation arise from the start-up and stop sequences, test methods required by the ecolabels should take these emissions into account. In this way it will encourage the boiler manufacturers to minimize annual emissions. The annual emissions of residential pellet heating system can be reduced by optimizing the number of start-ups of the pellet boiler. It is possible to reduce up to 85% of the number of start-ups by optimizing the system design and its controller such as switching of the boiler pump after it stops, using two temperature sensors for boiler ON/OFF control, optimizing of the positions of the connections to the storage tank, increasing the mixing valve temperature in the boiler circuit and decreasing the pump flow rate. For 85 % reduction of start-ups, 75 % of CO and TOC emission factors were reduced while 13% increase in NO and 15 % increase in particle emissions was observed.

Wood : from the forest to the consumer

Illegal logging causes a number of environmental and social damages in countries where wood is sourced from native forests. Logging in protected areas is an act of irresponsibility that exacerbates the loss of biodiversity. In addition, uncontrolled deforestation and bushfires may aggravate climate change, not to mention the negative effects they impose on local populations, such as the impoverishment of rural communities whose livelihoods depend on forest products. Several studies show that Brazil ranks high in terms of irresponsible use of natural resources, including native wood from the Amazon. Even more worrisome is the fact that the state, despite being responsible for regulating logging activities, is one of the largest consumers of native wood, which subverts the goals of any government committed to sustainable environmental management. By monitoring the development and impacts of illegal timber production and consumption around the world, the Friends of the Amazon Network – an initiative by the Getulio Vargas Foundation with support from the British Government and the European Commission – identified a need to describe and evaluate, in a brief and instructive manner, the different mechanisms the state has available to reverse this predatory practice. One of the aspects discussed in this book is the role of civil servants in major efforts aimed at repressing illegal logging and timber production, as well as identifying products derived from these activities in order to prevent their consumption. This is the purpose of this publication, which uses detailed infographics and a journalistic approach, including interviews and true stories, to outline the complexity of Amazon timber’s chain of custody – from logging, processing and transportation to commercialization in the Brazilian market.

Determination of fiber length and juvenile and mature wood zones from Hevea brasiliensis trees grown in Brazil

The aim of this study was to verify the average fiber length and the juvenile and mature wood zones from Hevea brasiliensis proveniences from a reforestation area in São Paulo, Brazil. For this purpose, five Hevea brasiliensis trees were randomly collected from a 50-year-old plantation, located in Balsamo, São Paulo, Brazil. The trees were cut and five flat sawn boards were obtained. The juvenile and mature wood zones were determined by fiber length measurement from the pith to the bark. The results showed that: (a) the juvenile wood of this species occurred approx. between 40 and 55 mm, from the pith, and from this point forward, the mature wood zone was found; (b) there was a significant difference between the average fiber length of juvenile wood (1.26 mm) and mature wood (1.51 mm).

Physical and mechanical properties of thermally modified wood from E. grandis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Application of X-ray technique in nondestructive evaluation of eucalypt wood

X-rays were initially used for the inspection of special-purpose wood pieces for quantitative evaluation properties of different species. X-ray densitometry has had its use expanded ill dendroclimatology of Picea engelmannii trees. Subsequent laboratories developed applications of X-ray densitometry for environmental, wood science and technology, and related areas. This paper describes the basic methodology of X-ray densitometry applied to the eucalypt wood analysis, as well its presenting the results of applications in three areas: (i) evaluation of wood biodegradation by white rot fungi, (ii) detection of sapwood and heartwood, and (iii) determination of the effect of management oil wood properties. The wood decayed by white rot fungi was detected by X-ray densitometry with it decreasing wood density due to the biodegradation of cell wall components. The sapwood and heartwood of eucalypts were separated in response to the attenuation of X-rays, reflected by the wood anatomical structure and chemical composition. Also, Ill eucalypt trees after the application of irrigation and i characteristic wood density profiles were detected. Ill addition, the significant potential of X-ray densitometry for eucalypt wood research and analysis is discussed.

Decay resistance of thermally-modified Eucalyptus grandis wood at 140 degrees C, 160 degrees C, 180 degrees C, 200 degrees C and 220 degrees C

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Viabilidade do uso de secadores solar de convecção natural e forçada para a secagem do coco Licuri

Licuri is a palm tree from the semiarid regions of Bahia State, Brazil. It is an important source of food and feed in that region, since their nuts are commonly eaten by humans and used as maize substitute for poultry feeding. The aim of this dissertation is to study the feasibility for use of natural convection solar dryers and forced being compared with the traditional drying outdoors for drying coconut licuri Syagrus coronate. The study led to the construction of two prototype solar dryer for carrying out experiments proving: model Solar Drying System Direct Exposure to Natural Convection built with wood, has a drying chamber with direct cover transparent glass laminates 4 mm, using techniques for proper isolation of the drying chamber. The two prototypes were comparatively analyzed for performance and drying efficiency with traditional extractive use by the community. Were evaluated the variables: time and drying rates and quality of the final samples of coconut licuri. The fruits were harvested and brought the town of Ouricuri, in the city of Caldeirão Grande, BA for the experiments comparing the three methods of drying was used a standard load of 4.0 kg The quantitative analysis for the result of the drying rate was found in 74% yield and 44% for natural and forced convection respectively compared with the traditional drying. These drying rates represent variation 3-5 times lower. Drying using forced convection licuri showed better quality, was found in a reddish pulp, representing the quantities that were kept of the nutrient beta carotene, and not notice the flavor change from the previous system, the final cost of construction of this system were higher . The prototypes built competitive advantage and had testified fully to resolve the technical difficulties previously encountered in the production of products made of coconut licuri. Allowing add value and increase their potential use for the fruit extractive communities of semi-arid region of Bahia

Análise química da madeira e casca de diferentes tipos de eucalipto antes e durante o cultivo de shiitake em toras

Avaliaram-se a composição química da madeira e da casca de sete espécies (E. saligna E. grandis, E. urophylla, E. camaldulensis, E. citriodora, E. paniculata e E. pellita) e três clones de eucalipto (híbridos de E. grandis x E. urophylla), antes e durante o cultivo das linhagens LE-95/01 e LE-96/18 de shiitake (Lentinula edodes), em toras. Cada linhagem de shiitake foi inoculada em nove toras de cada tipo de eucalipto com 1 m de comprimento e 9 a 14 cm de diâmetro. Assim, o delineamento experimental foi inteiramente casualizado, com 20 tratamentos e nove repetições, sendo cada repetição correspondente a uma tora. As toras foram mantidas em estufa climatizada, com temperatura de 25 ºC ± 5 e umidade relativa do ar entre 60-80%, durante 12 meses. Para a determinação da composição química da madeira, analisaram-se cunhas de discos e cascas de eucalipto recém-cortadas (sem inoculação das linhagens de L. edodes) e cunhas de discos e cascas retirados de toras já inoculadas com as linhagens de L. edodes após oito meses de incubação. Os resultados mostraram diferenças nos teores de holocelulose, lignina e extrativos totais na madeira e casca após o corte e depois de oito meses de incubação nas espécies e clones de eucalipto; o maior índice de decomposição da holocelulose na madeira, ao longo do tempo, ocorreu no E. saligna (5,5%), indicando, assim, ser o mais favorável para o desenvolvimento micelial do L. edodes. Já na casca aconteceu no clone 24 (22,2%). O E. camaldulensis apresentou o maior índice de decomposição da lignina na madeira (6,8%), ao longo do tempo. Já na casca, entre os eucaliptos testados, o E. grandis sofreu a maior decomposição de lignina (21,9%); o L. edodes degradou muito mais a holocelulose e lignina da casca que da madeira, tornando evidente a importância da casca; a casca da maioria dos tipos de eucaliptos apresentou menor teor de holocelulose, maior teor de extrativos totais e teores de lignina semelhantes ou superiores quando comparados com a madeira. O fator tipo de eucalipto (espécies e clones) teve maior efeito que o fator linhagem de L. edodes na degradação da holocelulose e lignina.

Seasonal variation in wood formation of Cedrela fissilis (Meliaceae)

Cambial activity and periodicity of secondary xylem formation in Cedrela fissilis, a semi-ring-porous species, were studied. Wood samples were collected periodically from 1996 to 2000. The phenology was related to climate data of the region. The cambium has one active and one dormant period per year. The active period coincides with the wet season when trees leaf-out. The dormant period coincides with the dry season when trees lose their leaves. Growth rings are marked by parenchyma bands that begin to be formed, together with the small latewood vessels, just before the cambium becomes dormant at the beginning of the dry season. These bands are added to when the cambium reactivates in the wet season. At this time, the large earlywood vessels of the growth rings are also formed. As these bands consist of both terminal and initial parenchyma, we suggest the general term marginal bands be used to describe them. The growth layers vary in width among and within the trees.

A comparison of the wood anatomy of 11 species from two cerrado habitats (cerrado s.s. and adjacent gallery forest)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

THE EFFECT of CARBONIZATION on WOOD STRUCTURE of DALBERGIA VIOLACEA, STRYPHNODENDRON POLYPHYLLUM, TAPIRIRA GUIANENSIS, VOCHYSIA TUCANORUM, and POUTERIA TORTA FROM THE BRAZILIAN CERRADO

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)