Dual carrier modulation demapping methods and performances for wireless USB

Dual Carrier Modulation (DCM) was chosen as the higher data rate modulation scheme for MB-OFDM (Multiband Orthogonal Frequency Division Multiplexing) in the UWB (Ultra-Wide Band) radio platform ECMA-368. ECMA-368 has been chosen as the physical implementation for high data rate Wireless USB (W-USB) and Bluetooth 3.0. In this paper, different demapping methods for the DCM demapper are presented, being Soft Bit, Maximum Likely (ML) Soft Bit and Log Likelihood Ratio (LLR). Frequency diversity and Channel State Information (CSI) are further techniques to enhance demapping methods. The system performance for those DCM demapping methods simulated in realistic multi-path environments are provided and compared.

OFDM joint data detection and phase noise cancellation based on minimum mean square prediction error

This paper proposes a new iterative algorithm for orthogonal frequency division multiplexing (OFDM) joint data detection and phase noise (PHN) cancellation based on minimum mean square prediction error. We particularly highlight the relatively less studied problem of "overfitting" such that the iterative approach may converge to a trivial solution. Specifically, we apply a hard-decision procedure at every iterative step to overcome the overfitting. Moreover, compared with existing algorithms, a more accurate Pade approximation is used to represent the PHN, and finally a more robust and compact fast process based on Givens rotation is proposed to reduce the complexity to a practical level. Numerical Simulations are also given to verify the proposed algorithm. (C) 2008 Elsevier B.V. All rights reserved.

Enhancing MB-OFDM throughput with dual circular 32-QAM

Quadrature Phase Shift Keying (QPSK) and Dual Carrier Modulation (DCM) are currently used as the modulation schemes for Multiband Orthogonal Frequency Division Multiplexing (MB-OFDM) in the ECMA-368 defined Ultra-Wideband (UWB) radio platform. ECMA-368 has been chosen as the physical radio platform for many systems including Wireless USB (W-USB), Bluetooth 3.0 and Wireless HDMI; hence ECMA-368 is an important issue to consumer electronics and the users experience of these products. To enable the transport of high-rate USB, ECMA-368 offers up to 480 Mb/s instantaneous bit rate to the Medium Access Control (MAC) layer, but depending on radio channel conditions dropped packets unfortunately result in a lower throughput. This paper presents an alternative high data rate modulation scheme that fits within the configuration of the current standard increasing system throughput by achieving 600 Mb/s (reliable to 3.1 meters) thus maintaining the high rate USB throughput even with a moderate level of dropped packets. The modulation system is termed Dual Circular 32-QAM (DC 32-QAM). The system performance for DC 32-QAM modulation is presented and compared with 16-QAM and DCM1.

Analysis of a DVB-T compliant receiver simulation under various multipath conditions

Since 1966, coded orthogonal frequency division multiplexing (COFDM) has been investigated to determine the possibility of reducing the overall throughput of a digitally modulated terrestrial television channel. In the investigations, many assumptions have emerged. One common misconception is that in a terrestrial environment, COFDM has an inherent immunity to multipath interference. A theoretical analysis of a multipath channel, along with simulation results has shown that this assumption does not hold the information is considered when including the radio frequency modulation and demodulation. This paper presents a background into the inception of COFDM, a mathematical analysis of the digitally modulated television signal under multipath conditions and the results of a European Digital Video Broadcasting-Terrestrial (DVB-T) compliant simulation model with MPEG-2 bitstreams transmitted under various multipath conditions.

Multiband OFDM modulation and demodulation for ultra wideband communications

This chapter considers the Multiband Orthogonal Frequency Division Multiplexing (MB- OFDM) modulation and demodulation with the intention to optimize the Ultra-Wideband (UWB) system performance. OFDM is a type of multicarrier modulation and becomes the most important aspect for the MB-OFDM system performance. It is also a low cost digital signal component efficiently using Fast Fourier Transform (FFT) algorithm to implement the multicarrier orthogonality. Within the MB-OFDM approach, the OFDM modulation is employed in each 528 MHz wide band to transmit the data across the different bands while also using the frequency hopping technique across different bands. Each parallel bit stream can be mapped onto one of the OFDM subcarriers. Quadrature Phase Shift Keying (QPSK) and Dual Carrier Modulation (DCM) are currently used as the modulation schemes for MB-OFDM in the ECMA-368 defined UWB radio platform. A dual QPSK soft-demapper is suitable for ECMA-368 that exploits the inherent Time-Domain Spreading (TDS) and guard symbol subcarrier diversity to improve the receiver performance, yet merges decoding operations together to minimize hardware and power requirements. There are several methods to demap the DCM, which are soft bit demapping, Maximum Likelihood (ML) soft bit demapping, and Log Likelihood Ratio (LLR) demapping. The Channel State Information (CSI) aided scheme coupled with the band hopping information is used as a further technique to improve the DCM demapping performance. ECMA-368 offers up to 480 Mb/s instantaneous bit rate to the Medium Access Control (MAC) layer, but depending on radio channel conditions dropped packets unfortunately result in a lower throughput. An alternative high data rate modulation scheme termed Dual Circular 32-QAM that fits within the configuration of the current standard increasing system throughput thus maintaining the high rate throughput even with a moderate level of dropped packets.

A study of COFDM in a terrestrial multipath environment

Coded orthogonal frequency division multiplexing (COFDM) has existed for many years but it was not until 1997 when the European Telecommunications Standards Institute proposed its use for the transmission of digital television through a terrestrial channel. Up to date, an assumption has been made concerning the resilience of COFDM in a multipath environment. This paper discusses this assumption, give results of a DVB-T compliant simulation and discuss the validity of this assumption based on the obtained results.

Nonlinear equalization of Hammerstein OFDM systems

A practical orthogonal frequency-division multiplexing (OFDM) system can generally be modelled by the Hammerstein system that includes the nonlinear distortion effects of the high power amplifier (HPA) at transmitter. In this contribution, we advocate a novel nonlinear equalization scheme for OFDM Hammerstein systems. We model the nonlinear HPA, which represents the static nonlinearity of the OFDM Hammerstein channel, by a B-spline neural network, and we develop a highly effective alternating least squares algorithm for estimating the parameters of the OFDM Hammerstein channel, including channel impulse response coefficients and the parameters of the B-spline model. Moreover, we also use another B-spline neural network to model the inversion of the HPA’s nonlinearity, and the parameters of this inverting B-spline model can easily be estimated using the standard least squares algorithm based on the pseudo training data obtained as a byproduct of the Hammerstein channel identification. Equalization of the OFDM Hammerstein channel can then be accomplished by the usual one-tap linear equalization as well as the inverse B-spline neural network model obtained. The effectiveness of our nonlinear equalization scheme for OFDM Hammerstein channels is demonstrated by simulation results.

Energy-efficient resource allocation in OFDM systems with distributed antennas

In this paper, we develop an energy-efficient resource-allocation scheme with proportional fairness for downlink multiuser orthogonal frequency-division multiplexing (OFDM) systems with distributed antennas. Our aim is to maximize energy efficiency (EE) under the constraints of the overall transmit power of each remote access unit (RAU), proportional fairness data rates, and bit error rates (BERs). Because of the nonconvex nature of the optimization problem, obtaining the optimal solution is extremely computationally complex. Therefore, we develop a low-complexity suboptimal algorithm, which separates subcarrier allocation and power allocation. For the low-complexity algorithm, we first allocate subcarriers by assuming equal power distribution. Then, by exploiting the properties of fractional programming, we transform the nonconvex optimization problem in fractional form into an equivalent optimization problem in subtractive form, which includes a tractable solution. Next, an optimal energy-efficient power-allocation algorithm is developed to maximize EE while maintaining proportional fairness. Through computer simulation, we demonstrate the effectiveness of the proposed low-complexity algorithm and illustrate the fundamental trade off between energy and spectral-efficient transmission designs.

Low complexity equalization of HCM systems with DPFFT demodulation over doubly-selective channels

To mitigate the inter-carrier interference (ICI) of doubly-selective (DS) fading channels, we consider a hybrid carrier modulation (HCM) system employing the discrete partial fast Fourier transform (DPFFT) demodulation and the banded minimum mean square error (MMSE) equalization in this letter. We first provide the discrete form of partial FFT demodulation, then apply the banded MMSE equalization to suppress the residual interference at the receiver. The proposed algorithm has been demonstrated, via numerical simulations, to be its superior over the single carrier modulation (SCM) system and circularly prefixed orthogonal frequency division multiplexing (OFDM) system over a typical DS channel. Moreover, it represents a good trade-off between computational complexity and performance.

Implementação de processador banda base ofdma para downlink lte em fpga

This work treats of an implementation OFDMA baseband processor in hardware for LTE Downlink. The LTE or Long Term Evolution consist the last stage of development of the technology called 3G (Mobile System Third Generation) which offers an increasing in data rate and more efficiency and flexibility in transmission with application of advanced antennas and multiple carriers techniques. This technology applies in your physical layer the OFDMA technical (Orthogonal Frequency Division Multiple Access) for generation of signals and mapping of physical resources in downlink and has as base theoretical to OFDM multiple carriers technique (Orthogonal Frequency Division Multiplexing). With recent completion of LTE specifications, different hardware solutions have been developed, mainly, to the level symbol processing where the implementation of OFDMA processor in base band is commonly considered, because it is also considered a basic architecture of others important applications. For implementation of processor, the reconfigurable hardware offered by devices as FPGA are considered which shares not only to meet the high requirements of flexibility and adaptability of LTE as well as offers possibility of an implementation quick and efficient. The implementation of processor in reconfigurable hardware meets the specifications of LTE physical layer as well as have the flexibility necessary for to meet others standards and application which use OFDMA processor as basic architecture for your systems. The results obtained through of simulation and verification functional system approval the functionality and flexibility of processor implemented

Extensive Comparisons of Optical Fast-OFDM and Conventional Optical OFDM for Local and Access Networks

A performance comparison between a recently proposed novel technique known as fast orthogonal frequency-division multiplexing (FOFDM) and conventional orthogonal frequency-division multiplexing (OFDM) is undertaken over unamplified, intensity-modulated, and direct-detected directly modulated laser-based optical signals. Key transceiver parameters, such as the maximum achievable transmission capacity and the digital-to-analog/analog-to-digital converter (DAC/ADC) effects are explored thoroughly. It is shown that, similarly to conventional OFDM, the least complex and bandwidth efficient FOFDM can support up to similar to 20 Gb/s over 500 m worst-case multimode fiber (MMF) links having 3 dB effective bandwidths of similar to 200 MHz X km. For compensation of the DAC/ADC roll-off, a power-loading (PL) algorithm is adopted, leading to an FOFDM system improvement of similar to 4 dB. FOFDM and conventional OFDM give similar optimum DAC/ADC parameters over 500 m worst-case MMF, while over 50 km single-mode fiber a maximum deviation of only similar to 1 dB in clipping ratio is observed due to the imperfect chromatic dispersion compensation caused by one-tap equalizers.

Supressão de interferência em sistemas de banda ultra larga e classificação automática de modulação

Esta tese apresenta duas contribuições distintas na área de sistemas de comunicações sem fi o. Primeiro, é apresentada uma formulação analítica para a análise de desempenho de sistemas utilizando multiplexação multibanda por divisão ortogonal na frequência (MB-OFDM, do inglês Multi-Band Orthogonal Frequency-Division Multiplexing ) com um ltro notch para mitigar a interferência em banda estreita causada por outros sistemas que operam dentro da faixa de frequências alocada para sistemas UWB. Em seguida, um novo front end para classificação automática de modulações com o uso de aprendizado discriminativo é proposto. Esse front end pode ser utilizado por qualquer classi cador discriminativo e consiste em ordenar magnitude e fase do símbolos recebidos. Os resultados obtidos pelo classi cador proposto mostraram-se competitivos com outros algoritmos já existentes na literatura.

Modelagem Cross-Layer da qualidade de experiência para transmissões de vídeo em sistemas sem fio OFDM

Este trabalho apresenta um estudo sobre transmissões de vídeo em sistemas sem fio. O objetivo da metodologia aplicada é comprovar a existência de uma relação direta entre a BER e a perda de qualidade (Perda de PSNR) nas transmissões de vídeo em sistemas OFDM (Orthogonal Frequency Division Multiplexing). Os resultados foram obtidos a partir de simulações, desenvolvidas no ambiente computacional Matlab®, e, aferições em cenários reais, realizadas no campus universitário e dentro do laboratório de estudos, em ambiente controlado. A partir da comparação entre dados simulados e aferidos, foi comprovada a relação entre BER e Perda de PSNR, resultando na formulação de um modelo empírico Cross-Layer com característica exponencial. A modelagem obteve erro RMS e desvio padrão próximos de 1,65 dB quando comparada com as simulações. Além disso, sua validação foi realizada a partir dos dados obtidos de cenários reais, que não foram usados para ajustar os parâmetros da equação obtida. O modelo obtido não necessita da especificação do tipo de canal ou codificação utilizada no FEC (Forward Error Correction), possibilitando uma futura integração com softwares de planejamento de redes, em versões comerciais ou open-sources.

Progettazione e analisi di soluzioni per la QOS e il controllo di flusso in Networks-on-chip

Nel documento vengono principalmente trattati i principali meccanismi per il controllo di flusso per le NoC. Vengono trattati vari schemi di switching, gli stessi schemi associati all'introduzione dei Virtual Channel, alcuni low-level flow control, e due soluzioni per gli end-to-end flow control: Credit Based e CTC (STMicroelectronics). Nel corso della trattazione vengono presentate alcune possibili modifiche a CTC per incrementarne le prestazioni mantenendo la scalabilità che lo contraddistingue: queste sono le "back-to-back request" e "multiple incoming connections". Infine vengono introdotti alcune soluzioni per l'implementazione della qualità di servizio per le reti su chip. Proprio per il supporto al QoS viene introdotto CTTC: una versione di CTC con il supporto alla Time Division Multiplexing su rete Spidergon.

Sistemi OFDM: prestazioni di livello fisico

I primi studi su Orthogonal Frequency Division Multiplexing (OFDM) sono stati fatti fin dal 1960, ma negli ultimi anni la modulazione OFDM è emersa come una tecnica di modulazione chiave commerciale per i sistemi di comunicazione ad alta velocità. La ragione principale di questo crescente interesse è dovuto alla sua capacità di fornire dati ad alta velocità impiegando sistemi con complessità bassa e contrastando l'interferenza intersimbolo (ISI) e quella intercanale (ICI). Per questo motivo la modulazione OFDM è stata adottata da diversi sistemi digitali wireline e wireless standard, come Digital Audio Broadcasting (DAB), Asymmetric Digital Subscriber Line (ADSL), Wireless Local Area Network (IEEE 802.11 a,g,n) oppure per WiMAX e LTE.