Thiophene-fluorene derivatives with high three-photon absorption activities and their application to optical power limiting

The three-photon absorption (3PA) properties of two thiophene-fluorene derivatives (abbreviated as MOTFTBr and ATFTBr) have been determined by using a Q-switched Nd:YAG laser pumped wish 38ps pulses at 1064nm in DMF. The measured 3PA cross-sections are 152x10(-78)cm(6)s(2) and 139x10(-78)cm(6)s(2), respectively. The optimized structures were obtained by AM1 calculations and the results indicate that these two molecules show nonplanar structures, and attaching different donors has different effects on the molecular structure. The charge density distributions during the excitation were also systematically studied by using AM1 method. In addition, an obvious optical power limiting effect induced by 3PA has been demonstrated for both derivatives.

Estudo da margem continental ibérica ocidental com base em dados gravimétricos e magnetométricos regionais

Os métodos potenciais são conhecidos como uma ferramenta útil para estudos regionais. Na Ibéria Ocidental, a gravimetria e a magnetometria podem ser utilizadas para auxiliar no entendimento de algumas questões sobre a estruturação tectônica offshore. Nesta região, tanto as estruturas geradas pela quebra continental, quanto às herdadas do embasamento variscano, tem uma importante contribuição para a resposta geofísica regional observada com estes métodos. Este trabalho tem como objetivo correlacionar as feições geofísicas observadas com alguns modelos geológicos do arcabouço tectônico da Ibéria Ocidental já publicados na literatura. Mapas filtrados foram usados para auxiliar no reconhecimento de diferentes assinaturas geofísicas, os quais foram calculados a partir dos mapas de gravidade Bouguer e do campo magnético total tais como o gradiente horizontal total, derivada tilt, derivada vertical, e integral vertical. O domínio crustal continental foi definido a partir da interpretação dos dados gravimétricos, utilizando gradiente de gravidade horizontal total da Anomalia Bouguer. Os dados magnéticos, originais e filtrados, foram utilizados para identificar mais três domínios regionais offshore, que sugerem a existência de três tipos de crosta não-siálica. Dois deles são propostos como domínios de transição. A região da crosta de transição mais próxima do continente tem uma fraca resposta regional magnética, e a porção mais distal é um domínio de anomalia de alta amplitude, semelhante à resposta magnética oceânica. O limite crustal oceânico não pôde ser confirmado, mas um terceiro domínio offshore, a oeste da isócrona C34, poderia ser considerado como crosta oceânica, devido ao padrão magnético que apresenta. Alguns lineamentos do embasamento foram indicados na crosta continental offshore. As feições gravimétricas e magnéticas interpretadas coincidem, em termos de direção e posição, com zonas de sutura variscanas, mapeados em terra. Assim, esses contatos podem corresponder à continuação offshore destas feições paleozoicas, como o contato entre as zonas de Ossa Morena-Zona Centro-Ibérica. Nesta interpretação, sugere-se que a crosta continental offshore pode ser composta por unidades do Sudoeste da Península Ibérica. Isto permite considerar que a Falha de Porto-Tomar pertence a uma faixa de deformação strike-slip, onde parte das bacias mesozoicas da margem continental está localizada.

Capillary electrochromatographic separation of enantiomers on chemically bonded type of cellulose derivative chiral stationary phases with a positively charged spacer

Positively charged chiral stationary phases (CSPs) were prepared for capillary electrochromatography (CEC) separation of enantiomers by chemically immobilizing cellulose derivatives onto diethylenetriaminopropylated silica (DEAPS) with tolylene-2,4-diisocyanate (TDI) as a spacer reagent. Anodic electroosmotic mobility was observed in both nonaqueous and aqueous mobile phases due to the positively charged amines on the surface of the prepared CSPs. For comparison, the traditionally used 3-aminopropyl silica (APS) was also adopted as the base material instead of DEAPS to prepare CSP. It was observed that the EOF on the DEAPS-based CSP was 18%-60% higher than that on the APS-based CSP under nonaqueous mobile phase conditions. Separation of enantiomers in CEC was performed on the positively charged CSPs with the nonaqueous mobile phases of pure ethanol or mixture of hexane-alcohol and the aqueous phases of acetonitrile-water or 95% ethanol. Fast separation of enantiomers was achieved on the newly prepared CSPs.

Low temperature X-ray structures of two crystalline forms (I) and (II) of the pyrimidine derivative and sodium channel blocker BW1003C87: 5-(2,3,5-trichlorophenyl)-2,4-diaminopyrimidine

The X-ray crystal structures of two crystalline forms of 5-(2,3,5-trichlorophenyl)-2,4-diaminopyrimidine, C10H7Cl3N4 (code name BW1003C87) (I) and (II), have been carried out at liquid nitrogen temperature. A detailed comparison of the two structures is given. Both are centrosymmetric, with structure (I) in the triclinic space group P (1) over bar unit cell a = 6.4870(10), b = 9.216(2), c = 12.016(2) angstrom, alpha = 75.78(3)degrees, beta = 89.95(3)degrees, gamma = 83.45(3)degrees, V = 691.5(2) angstrom(3), Z = 2 and density (calculated) = 1.544 Mg/m(3); and (II) in the monoclinic space group P2(1)/c, unit cell a = 12.000(2), b = 7.518(2), c = 13.450(3) angstrom, beta = 97.87(3)degrees, V = 1202.0(5) angstrom(3), Z = 4, Density (calculated) = 1.600 Mg/m(3). Structure (I) includes a solvated CH3OH in the lattice. Final R indices [I > 2sigma(I)] are R1 = 0.0427, wR2 = 0.1075 for (I) and R1 = 0.0487, wR2 = 0.1222 for (II). R indices (all data) are R1 = 0.0470, wR2 = 0.1118 for (I) and R1 = 0.0623, wR2 = 0.1299 for (II). 5-Phenyl-2,4 diaminopyrimidine and 6-phenyl-1,2,4 triazine derivatives, which include lamotrigine (3,5-diamino-6-(2,3-dichlorophenyl)-1,2,4-triazine), have been investigated for some time for their effects on the central nervous system. Both lamotrigine and 5-(2,3,5-trichlorophenyl)-2,4-diaminopyrimidine (code name BW1003C87), the subject of the present study, are anticonvulsant as well as neuroprotective in models of brain ischaemia and in a model of white matter ischaemia. BW1003C87 is a sodium channel blocker which also reduces the release of the neurotransmitter glutamate. The three dimensional structures reported here form part of a newly developed data base for the detailed investigation of members of this drug family and their biological activities.

X-ray crystallographic structures of neuroprotective pyrimidine derivatives: (I) the mesylate salt of BW1003C87 and (II) sipatrigine base

Drugs based on 5-phenyl-2,4 diamino pyrimidine and 6-phenyl-1,2,4 triazine derivatives are well known for their effects on the central nervous system. The study presented here provides detailed crystal structures of two pyrimidine derivatives which have neuroprotective properties in models of both grey and white matter ischemia. Recently published studies suggest that the compounds lamotrigine (a triazine derivative), and the two pyrimidines BW1003C87 (I) and sipatrigine (II) mediate their primary in vivo mode of action by inhibiting voltage-gated Na+ channels. The X-ray crystal structures will contribute valuable data for applications involving binding and modelling studies of the biological actions of these drugs.

Synthèse et caractérisation photophysique et électrochimique d'une nouvelle classe de composés à base de fluorène et 2-thiophène

Mémoire numérisé par la Division de la gestion de documents et des archives de l'Université de Montréal

Self-immolative base-mediated conjugate release from triazolylmethylcarbamates

A range of carbamate functionalized 1,4-disubstituted triazoles featuring a base sensitive trigger residue, plus a model aromatic amine reporter group, were prepared via copper(I) catalysed azide–alkyne cycloaddition and evaluated for their self-immolative characteristics. This study revealed a clear structure–reactivity relationship, via Hammett analysis, between the structure of the 1,4-disubstituted triazole and the rate of self-immolative release of the amine reporter group, thus demonstrating that under basic conditions this type of triazole derivative has the potential to be employed in a range of chemical release systems.

Development and Validation of an UV-Derivative Spectrophotometric Method for Determination of Glimepiride in Tablets

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento de um dispositivo para obtenção de monocristais de ligas à base de cobre

This paper describes the drawing, construction and optimization of a device, which can be used to obtain single crystals of different metallic materials with melting point from 550 to 1050°C. Components of ease obtaining and of low cost were used. The device was based on the modified Bridgman technique and it was used to obtain single crystals of copper-based alloys. The temperature axial profiles and a difference less then 1% in the temperature between the wall and the center of the ceramic tube in the critical region for obtaining single crystals of good quality indicated that the oven presents a good thermal stability. Single crystals of CuZnAl and CuAlAg alloys of good quality were growth and characterized using optical microscopy and Laüe X-ray back reflection.

Effect of microwave treatments on dimensional accuracy of maxillary acrylic resin denture base

Microwave energy has been used as an alternative method for disinfection and sterilization of dental prostheses. This study evaluated the influence of microwave treatment on dimensional accuracy along the posterior palatal border of maxillary acrylic resin denture bases processed by water-bath curing. Thirty maxillary acrylic bases (3-mm-thick) were made on cast models with Clássico acrylic resin using routine technique. After polymerization and cooling, the sets were deflasked and the bases were stored in water for 30 days. Thereafter, the specimens were assigned to 3 groups (n=10), as follows: group I (control) was not submitted to any disinfection cycle; group II was submitted to microwave disinfection for 3 min at 500 W; and in group III microwaving was done for 10 min at 604 W. The acrylic bases were fixed on their respective casts with instant adhesive (Super Bonder®) and the base/cast sets were sectioned transversally in the posterior palatal zone. The existence of gaps between the casts and acrylic bases was assessed using a profile projector at 5 points. No statistically significant differences were observed between the control group and group II. However, group III differed statistically from the others (p<0.05). Treatment in microwave oven at 604 W for 10 min produced the greatest discrepancies in the adaptation of maxillary acrylic resin denture bases to the stone casts.

Bond strength of acrylic teeth to denture base resin after various surface conditioning methods before and after thermocycling

This study aimed to evaluate the durability of adhesion between acrylic teeth and denture base acrylic resin. The base surfaces of 24 acrylic teeth were flatted and submitted to 4 surface treatment methods: SM1 (control): No SM; SM2: application of a methyl methacrylate-based bonding agent (Vitacol); SM3: air abrasion with 30-μm silicone oxide plus silane; SM4: SM3 plus SM2. A heat-polymerized acrylic resin was applied to the teeth. Thereafter, bar specimens were produced for the microtensile test at dry and thermocyled conditions (60 days water storage followed by 12,000 cycles). The results showed that bond strength was significantly affected by the SM (P < .0001) (SM4 = SM2 > SM3 > SM1) and storage regimens (P < .0001) (dry > thermocycled). The methyl methacrylate-based adhesive showed the highest bond strength.

The effect of water immersion on the shear bond strength between chairside reline and denture base acrylic resins: Basic science research

Purpose: The effect of water immersion on the shear bond strength (SBS) between 1 heat-polymerizing acrylic resin (Lucitone 550-L) and 4 autopolymerizing reline resins (Kooliner-K, New Truliner-N, Tokuso Rebase Fast-T, Ufi Gel Hard-U) was investigated. Specimens relined with resin L were also evaluated. Materials and Methods: One hundred sixty cylinders (20 × 20 mm) of L denture base resin were processed, and the reline resins were packed on the prepared bonding surfaces using a split-mold (3.5 × 5.0 mm). Shear tests (0.5 mm/min) were performed on the specimens (n = 8) after polymerization (control), and after immersion in water at 37°C for 7, 90, and 180 days. All fractured surfaces were examined by scanning electron microscopy (SEM) to calculate the percentage of cohesive fracture (PCF). Shear data were analyzed with 2-way ANOVA and Tukey's test; Kruskall-Wallis test was used to analyze PCF data (α = 0.05). Results: After 90 days water immersion, an increase in the mean SBS was observed for U (11.13 to 16.53 MPa; p < 0.001) and T (9.08 to 13.24 MPa, p = 0.035), whereas resin L showed a decrease (21.74 MPa to 14.96 MPa; p < 0.001). The SBS of resins K (8.44 MPa) and N (7.98 MPa) remained unaffected. The mean PCF was lower than 32.6% for K, N, and T, and higher than 65.6% for U and L. Conclusions: Long-term water immersion did not adversely affect the bond of materials K, N, T, and U and decreased the values of resin L. Materials L and U failed cohesively, and K, N, and T failed adhesively. © 2007 by The American College of Prosthodontists.

Effect of experimental photopolymerized coatings on the hydrophobicity of a denture base acrylic resin and on Candida albicans adhesion

Objective: This study investigated the effect of experimental photopolymerized coatings, containing zwitterionic or hydrophilic monomers, on the hydrophobicity of a denture base acrylic resin and on Candida albicans adhesion. Methods: Acrylic specimens were prepared with rough and smooth surfaces and were either left untreated (control) or coated with one of the following experimental coatings: 2-hydroxyethyl methacrylate (HE); 3-hydroxypropyl methacrylate (HP); and 2-trimethylammonium ethyl methacrylate chloride (T); and sulfobetaine methacrylate (S). The concentrations of these constituent monomers were 25%, 30% or 35%. Half of the specimens in each group (control and experimentals) were coated with saliva and the other half remained uncoated. The surface free energy of all specimens was measured, regardless of the experimental condition. C. albicans adhesion was evaluated for all specimens, both saliva conditioned and unconditioned. The adhesion test was performed by incubating specimens in C. albicans suspensions (1 × 10 7 cell/mL) at 37 °C for 90 min. The number of adhered yeasts were evaluated by XTT (2,3-bis[2-methoxy-4-nitro-5-sulfophenyl]-5-[{phenylamino} carbonyl]-2H-tetrazolium-hydroxide) method. Results: For rough surfaces, coatings S (30 or 35%) and HP (30%) resulted in lower absorbance values compared to control. These coatings exhibited more hydrophilic surfaces than the control group. Roughness increased the adhesion only in the control group, and saliva did not influence the adhesion. The photoelectron spectroscopy analysis (XPS) confirmed the chemical changes of the experimental specimens, particularly for HP and S coatings. Conclusions: S and HP coatings reduced significantly the adhesion of C. albicans to the acrylic resin and could be considered as a potential preventive treatment for denture stomatitis. © 2012 Elsevier Ltd.

Estudo físico-químico da atividade fungicida de derivados anfifílicos de quitosana contra fungos do gênero Aspergillus : interação com modelos de membranas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A first-derivative spectrophotometric method for the determination of ciprofloxacin hydrochloride in ophthalmic solution

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)