Strength prediction of adhesively-bonded scarf repairs in composite structures under bending

This work reports on the experimental and numerical study of the bending behaviour of two-dimensional adhesively-bonded scarf repairs of carbon-epoxy laminates, bonded with the ductile adhesive Araldite 2015®. Scarf angles varying from 2 to 45º were tested. The experimental work performed was used to validate a numerical Finite Element analysis using ABAQUS® and a methodology developed by the authors to predict the strength of bonded assemblies. This methodology consists on replacing the adhesive layer by cohesive elements, including mixed-mode criteria to deal with the mixed-mode behaviour usually observed in structures. Trapezoidal laws in pure modes I and II were used to account for the ductility of the adhesive used. The cohesive laws in pure modes I and II were determined with Double Cantilever Beam and End-Notched Flexure tests, respectively, using an inverse method. Since in the experiments interlaminar and transverse intralaminar failures of the carbon-epoxy components also occurred in some regions, cohesive laws to simulate these failure modes were also obtained experimentally with a similar procedure. A good correlation with the experiments was found on the elastic stiffness, maximum load and failure mode of the repairs, showing that this methodology simulates accurately the mechanical behaviour of bonded assemblies.

Strength prediction and experimental validation of adhesive joints including polyethylene, carbon-epoxy and aluminium adherends

Polyolefins are especially difficult to bond due to their non-polar, non-porous and chemically inert surfaces. Acrylic adhesives used in industry are particularly suited to bond these materials, including many grades of polypropylene (PP) and polyethylene (PE), without special surface preparation. In this work, the tensile strength of single-lap PE and mixed joints bonded with an acrylic adhesive was investigated. The mixed joints included PE with aluminium (AL) or carbon fibre reinforced plastic (CFRP) substrates. The PE substrates were only cleaned with isopropanol, which assured cohesive failures. For the PE CFRP joints, three different surfaces preparations were employed for the CFRP substrates: cleaning with acetone, abrasion with 100 grit sand paper and peel-ply finishing. In the PE AL joints, the AL bonding surfaces were prepared by the following methods: cleaning with acetone, abrasion with 180 and 320 grit sand papers, grit blasting and chemical etching with chromic acid. After abrasion of the CFRP and AL substrates, the surfaces were always cleaned with acetone. The tensile strengths were compared with numerical results from ABAQUS® and a mixed mode (I+II) cohesive damage model. A good agreement was found between the experimental and numerical results, except for the PE AL joints, since the AL surface treatments were not found to be effective.

Information technology service management: an experimental approach towards IT service prediction

Dissertation presented to obtain a Masters degree in Computer Science

Strength prediction of single- and double-lap joints by standard and extended finite element modelling

The structural integrity of multi-component structures is usually determined by the strength and durability of their unions. Adhesive bonding is often chosen over welding, riveting and bolting, due to the reduction of stress concentrations, reduced weight penalty and easy manufacturing, amongst other issues. In the past decades, the Finite Element Method (FEM) has been used for the simulation and strength prediction of bonded structures, by strength of materials or fracture mechanics-based criteria. Cohesive-zone models (CZMs) have already proved to be an effective tool in modelling damage growth, surpassing a few limitations of the aforementioned techniques. Despite this fact, they still suffer from the restriction of damage growth only at predefined growth paths. The eXtended Finite Element Method (XFEM) is a recent improvement of the FEM, developed to allow the growth of discontinuities within bulk solids along an arbitrary path, by enriching degrees of freedom with special displacement functions, thus overcoming the main restriction of CZMs. These two techniques were tested to simulate adhesively bonded single- and double-lap joints. The comparative evaluation of the two methods showed their capabilities and/or limitations for this specific purpose.

Synthesis of Sub-5 NM Co-Doped SnO2 nanoparticles and their structural microstructural, optical and photocatalytic properties

A swift chemical route to synthesize Co-doped SnO2 nanopowders is described. Pure and highly stable Sn1-xCoxO2-delta (0 <= x <= 0.15) crystalline nanoparticles were synthesized, with mean grain sizes <5 nm and the dopant element homogeneously distributed in the SnO2 matrix. The UV-visible diffuse reflectance spectra of the Sn1-xCoxO2-delta samples reveal red shifts, the optical bandgap energies decreasing with increasing Co concentration. The samples' Urbach energies were calculated and correlated with their bandgap energies. The photocatalytic activity of the Sn1-xCoxO2-delta samples was investigated for the 4-hydroxylbenzoic acid (4-HBA) degradation process. A complete photodegradation of a 10 ppm 4-HBA solution was achieved using 0.02% (w/w) of Sn0.95Co0.05O2-delta nanoparticles in 60 min of irradiation. (C) 2014 Elsevier B.V. All rights reserved.

Fractional discrete-time signal processing: scale conversion and linear prediction

Nonlinear Dynamics, Vol. 29

New results on fractional linear prediction

Proceedings of the European Control Conference, ECC’01, Porto, Portugal, September 2001

Sub-micron structuring of silicon using femtosecond laser interferometry

We report the fabrication of planar sub-micron gratings in silicon with a period of 720 nm using a modified Michelson interferometer and femtosecond laser radiation. The gratings consist of alternated stripes of laser ablated and unmodified material. Ablated stripes are bordered by parallel ridges which protrude above the unmodified material. In the regions where ridges are formed, the laser radiation intensity is not sufficient to cause ablation. Nevertheless, melting and a significant temperature increase are expected, and ridges may be formed due to expansion of silicon during resolidification or silicon oxidation. These conclusions are consistent with the evolution of the stripes morphology as a function of the distance from the center of the grating.

Sub-notificação de reacções adversas medicamentosas : um problema com solução? : contribuição para o conhecimento da sub-notificação de RAMs em Portugal e implementação de medidas minimizadoras do impacte

RESUMO - Introdução: As Reacções Adversas Medicamentosas (RAMs) constituem um grave problema de Saúde Pública em termos da mortalidade e morbilidade provocadas, tendo também um impacto económico considerável nos Sistemas de Saúde. Os Sistemas de Notificacão Espontânea de RAMs são considerados como o método de vigilância de medicamentos mais eficaz, sendo a sub-notificação de RAMs uma das suas maiores limitações. Em termos globais, foi estimado que apenas 6% de todas as reacções adversas são notificadas. Portugal apresenta uma taxa de notificação de RAMs relativamente baixa quando comparada com os países mais notificadores da Europa. São objectivos deste estudo: 1) caracterizar as atitudes e os comportamentos dos médicos, dos farmacêuticos e dos enfermeiros em Portugal Continental relativamente à notificação de RAMs; e 2) caracterizar a efectividade de intervenções educacionais destinadas a reduzir a sub-notificação de RAMs. Métodos: Numa primeira fase será efectuado um estudo de caso-controlo em médicos, farmacêuticos e enfermeiros de Portugal Continental, a exercer actividade no Servico Nacional de Saúde (SNS), de modo a caracterizar as suas atitudes e comportamentos relativamente à notificação de RAMs. Como casos serão considerados os Profissionais de Saúde que notificaram pelo menos uma RAM num determinado período e os controlos os Profissionais de Saúde que não notificaram qualquer RAM nesse mesmo período, sendo estes útimos seleccionados aleatoriamente. O estudo será conduzido através de um questionário de auto-resposta, em que as questões relativas às atitudes e comportamentos são baseadas nos “sete pecados mortais” de Inman. Será utilizada uma Escala Visual Analógica para registar as respostas, podendo estas ir de zero (totalmente em desacordo) até 10 (totalmente de acordo). Será utilizada uma análise de regressão logística para determinar o odds ratio ajustado (ORadj) da notificação de RAMs para uma mudança de exposição correspondente ao range interquartil para cada atitude. Numa segunda fase, será efectuado ensaio aleatorizado controlado de cluster, para caracterizar a efectividade das intervenções educacionais realizadas sobre as causas identificadas na primeira parte do trabalho, com o intuito de reduzir a sub-notificação de RAMs. Com base em informacão de 2007 foram identificados 43 clusters dispersos pelas várias Regiões de Saúde. As intervenções educacionais são compostas por uma apresentação com uma hora de duração complementada por um folheto recordatório. Serão ainda realizados dois sub-estudos, em que o V1.0, Final 28Set09 viii Sub-notificação de RAMs em Portugal – Um problema com solução ? primeiro tentará caracterizar o efeito de contaminação entre Profissionais de Saúde e o segundo pretende caracterizar a duração do efeito das intervenções educacionais. Resultados a atingir: Pretende-se, com a implementação deste projecto, aumentar o número de notificações de RAMs pelos médicos, farmacêuticos e enfermeiros em cerca de 110%, de modo a atingir-se uma taxa de notificação de aproximadamente 300 notificações por milhão de habitantes por ano (i.e., multiplicar por 2,1 o número notificações existentes). -------------------ABSTRACT - Introduction: The Adverse Drug Reactions (ADRs) are a serious Public Health problem in terms of mortality and morbidity caused, being also an economic burden for the health systems. The Spontaneous Adverse Event Reporting Systems are considered as the most effective drug surveillance methods, in which the ADR under-reporting represents one of its biggest limitations. It was estimated that only 6% of all adverse reactions are notified globally. When comparing with high ADR reporting rate countries Portugal shows a low ADR reporting rate. This study aims to: 1) characterize the physicians, pharmacists and nurses attitudes and behaviours related to ADR under-reporting; 2) characterize the educational interventions effectiveness to decrease the ADRs under-reporting. Methods: During a first phase a case-control study will be conducted in physicians, pharmacists and nurses in Continental Portugal working in the National Health System (NHS) in order to characterize their attitudes and behaviours related to ADR reporting. The Healthcare Professionals that have reported at least one ADR during a determined period will be considered as the cases and those that have not reported any ADR during the same period will be considered as the controls. The controls will be randomly selected. The study will be conducted through a self-administered questionnaire in which the questions related to the attitudes and behaviours are based in the Inmans’s “seven mortal sins”. A Visual Analogue Scale will be used to record the responses. The responses can range from 0 (totally disagree) to 10 (totally agree). Logistic regression will be used to determine the ADR reporting adjusted odds ratio (ORadj) for a change in the exposure corresponding to the interquartile range for each attitude. In the second phase of the study a cluster-randomized controlled trial will be conducted to characterize the educational interventions effectiveness focused on the first phase identified causes with the aim to decrease the ADRs under-reporting. Based in 2007’s information 43 clusters have been identified throughout the several Health Regions. The educational interventions are composed of one hour presentation complemented by an informational leaflet. Two sub-studies will be also conducted in which the first one will try to characterize the contamination effect between the Healthcare Professionals and the second to characterize the educational interventions effect duration. V1.0, Final 28Set09 x Sub-notificação de RAMs em Portugal – Um problema com solução ? Outcome: With the project implementation an increase of the ADR notifications performed by the physicians, pharmacists and nurses by 110% is aimed in order to obtain approximately 300 notifications per million habitants per year (i.e., multiply by 2,1 the existent notifications).

Evaluation of temporal, seasonal and geographic stability of the molluscicidal property of Euphorbia splendens latex

Laboratory tests with aqueous solutions of Euphorbia splendens var. hislopii latex have demonstrated seasonal stability of the molluscicidal principle, with LD90 values of 1.14 ppm (spring), 1.02 ppm (fall), 1.09 ppm (winter), and 1.07 ppm (summer) that have been determined against Biomphalaria tenagophila in the field. Assays on latex collected in Belo Horizonte and Recife yielded LD90 values similar to those obtained with the reference substance collected in Rio de Janeiro (Ilha do Governador), demonstrating geographic stability of the molluscicidal effect. The molluscicidal action of aqueous dilutions of the latex in natura, centrifuged (precipitate) and lyophilized, was stable for up to 124 days at room temperature (in natura) and for up to 736 days in a common refrigerator at 10 to 12ºC (lyophilized product). A 5.0 ppm solution is 100% lethal for snails up to 13 days after preparation, the effect being gradually lost to almost total inactivity by the 30th day. This observation indicated that the active principle is instable. These properties together with the wide distribution of the plant, its resistance and adaptation to the tropical climate, its easy cultivation and the easy obtention of latex and preparation of the molluscicidal solution, make this a promising material for large-scale use in the control of schistosomiasis

Adherend thickness effect on the tensile fracture toughness of a structural adhesive using an optical data acquisition method

Adhesive bonding is nowadays a serious candidate to replace methods such as fastening or riveting, because of attractive mechanical properties. As a result, adhesives are being increasingly used in industries such as the automotive, aerospace and construction. Thus, it is highly important to predict the strength of bonded joints to assess the feasibility of joining during the fabrication process of components (e.g. due to complex geometries) or for repairing purposes. This work studies the tensile behaviour of adhesive joints between aluminium adherends considering different values of adherend thickness (h) and the double-cantilever beam (DCB) test. The experimental work consists of the definition of the tensile fracture toughness (GIC) for the different joint configurations. A conventional fracture characterization method was used, together with a J-integral approach, that take into account the plasticity effects occurring in the adhesive layer. An optical measurement method is used for the evaluation of crack tip opening and adherends rotation at the crack tip during the test, supported by a Matlab® sub-routine for the automated extraction of these quantities. As output of this work, a comparative evaluation between bonded systems with different values of adherend thickness is carried out and complete fracture data is provided in tension for the subsequent strength prediction of joints with identical conditions.

Seasonal patterns of polycyclic aromatic hydrocarbons in digestive gland and arm of octopus (Octopus vulgaris) from the Northwest Atlantic

Among organic pollutants existing in coastal areas, polycyclic aromatic hydrocarbons (PAHs) are of great concern due to their ubiquity and carcinogenic potential. The aim of this study was to evaluate the seasonal patterns of PAHs in the digestive gland and arm of the common octopus (Octopus vulgaris) from the Northwest Atlantic Portuguese coast. In the different seasons, 18 PAHs were determined and the detoxification capacity of the species was evaluated. Ethoxyresorufin O-deethylase (EROD) and ethoxycoumarin O-deethylase (ECOD) activities were measured to assess phase I biotransformation capacity. Individual PAH ratios were used for major source (pyrolytic/petrogenic) analysis. Risks for human consumption were determined by the total toxicity equivalence approach. Generally, low levels of PAHs were detected in the digestive gland and in the arm of octopus, with a predominance of low molecular over high molecular weight compounds. PAHs exhibited seasonality in the concentrations detected and in their main emission sources. In the digestive gland, the highest total PAH levels were observed in autumn possibly related to fat availability in the ecosystem and food intake. The lack of PAH elimination observed in the digestive gland after captivity could be possibly associated to a low biotransformation capacity, consistent with the negligible/undetected levels of EROD and ECOD activity in the different seasons. The emission sources of PAHs found in the digestive gland varied from a petrogenic profile observed in winter to a pyrolytic pattern in spring. In the arm, the highest PAH contents were observed in June; nevertheless, levels were always below the regulatory limits established for food consumption. The carcinogenic potential calculated for all the sampling periods in the arm were markedly lower than the ones found in various aquatic species from different marine environments. The results presented in this study give relevant baseline data for environmental monitoring of organic pollution in coastal areas.

Evolução da ocupação e da perda de solo numa pequena sub-bacia da Bacia Hidrográfica do Rio Sado

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia do Ambiente,Perfil Gestão de Sistemas Ambientais

Seasonal variation of anti-resa/Pf155 Plasmodium falciparum antibodies in three localities from the state of Amapá, Brazil

Anti-RESA/Pf155 antibodies were assayed in sera of individuals from three localities (Laranjal do Jari, Vila Padaria and Vila Paraíso) in the State of Amapá, Brazil, during the long-rains and short-rains seasons. All of these had negative blood smears for malaria. Most of the sera collected were positive in Indirect Fluorescent Antibody (IFA) with P. falciparum parasites, with no seasonal variation. A high percentage of these sera (62% to 100%) was RESA positive by Modified Indirect Fluorescent Antibody (MIFA), with a significant (p < 0.05) increase of geometric mean titers during the short-rains season, when the transmission of the disease is highest. ELISA with three repetitive RESA peptides (EENV)3 (4x3), (EENVEHDA)2 (8x2) and (DDEHVEEPTVA)2(11x2) did not reveal statistically significant seasonal variations, although a small enhancement of positivity was observed in V. Padaria (15.3 to 38.8%) in the short-rains season with the 8x2 peptides, and with 4x3 and 8x2 peptides in V. Paraíso, with a decrease in 11x2. MIFA titers appeared to be correlated mainly to the peptide 4x3 and it was the immunodominant in the three localities.