A detailed chemistry multi-cycle simulation of a gasoline fueled HCCI engine operated with NVO

A previously developed Stochastic Reactor Model (SRM) is used to simulate combustion in a four cylinder in-line four-stroke naturally aspirated direct injection Spark Ignition (SI) engine modified to run in Homogeneous Charge Compression Ignition (HCCI) mode with a Negative Valve Overlap (NVO). A portion of the fuel is injected during NVO to increase the cylinder temperature and enable HCCI combustion at a compression ratio of 12:1. The model is coupled with GT-Power, a one-dimensional engine simulation tool used for the open valve portion of the engine cycle. The SRM is used to model in-cylinder mixing, heat transfer and chemistry during the NVO and main combustion. Direct injection is simulated during NVO in order to predict heat release and internal Exhaust Gas Recycle (EGR) composition and mass. The NOx emissions and simulated pressure profiles match experimental data well, including the cyclic fluctuations. The model predicts combustion characteristics at different fuel split ratios and injection timings. The effect of fuel reforming on ignition timing is investigated along with the causes of cycle to cycle variations and unstable operation. A detailed flux analysis during NVO unearths interesting results regarding the effect of NOx on ignition timing compared with its effect during the main combustion. © 2009 SAE International.

Recovery of the stocks of the European eel (Anguilla anguilla) by spawner enhancement

The production of healthy high quality female European eel in recycle systems is proposed as a means to secure sufficient numbers of silver eel for spawning migration in order to meet the requirements of the European Commission’s proposal for a Regulation for the recovery of the stock of the European eel. Main advantages besides checks for parasites and viral diseases and avoidance of elevated levels of specific pollutants are the easily controllable numbers of spawners to be released and a reduction of labour and costs that will occur when acting along the lines of the Commission’s proposal.

Modelagem, simulação e otimização operacional de unidades de síntese de metanol

A indústria de processos químicos tem sofrido consideráveis transformações devido ao acirramento da competitividade. Importantes progressos tecnológicos têm sido atingidos através de técnicas de modelagem, simulação e otimização visando o aumento da lucratividade e melhoria contínua nos processos industriais. Neste contexto, as plantas de metanol, um dos mais importantes produtos petroquímicos, podem ser destacadas. Atualmente, a principal matéria-prima para obtenção de metanol é o gás natural. A produção do metanol é caracterizada por três etapas: geração de gás de síntese, conversão do gás de síntese em metanol (unidade de síntese ou loop de síntese) e purificação do produto na especificação requerida. Os custos fixos e variáveis da unidade de síntese são fortemente dependentes das variáveis operacionais, como temperatura, pressão, razão de reciclo e composição da carga. Desta forma, foi desenvolvido um conjunto de modelos e algoritmos computacionais para representar matematicamente unidades de síntese de metanol. O modelo apresenta operações unitárias associadas aos seguintes equipamentos: divisores de correntes, misturadores de correntes, compressores, trocadores de calor, vasos de flash e reatores. Inicialmente, foi proposto um simulador estacionário, que serviu como base para um pseudo-estacionário, o qual contempla a desativação do catalisador por sinterização térmica. Os simuladores foram criados segundo uma arquitetura seqüencial modular e empregou-se o método de substituição sucessiva para a convergência dos reciclos. O estudo envolveu dois fluxogramas típicos, um constituído por reatores adiabáticos em série, enquanto o outro constituído por um reator tipo quench. Uma análise do efeito das principais variáveis operacionais foi realizada para o reator e para o loop de síntese. Estudou-se também o efeito da desativação do catalisador ao longo do tempo. Uma ferramenta de otimização operacional foi empregada para alcançar a máxima produção manipulando as injeções de carga fria na entrada dos leitos catalíticos. Formulou-se também um problema de maximização do lucro em função da otimização de paradas da unidade para troca do catalisador. Os resultados obtidos apontam que a ferramenta desenvolvida é promissora para a compreensão e otimização da unidade objeto deste estudo

Posto de Troca de Recicláveis por desconto em conta de energia elétrica, em comunidade de baixa renda.

A proposta deste trabalho é de criar receita e renda para comunidades de baixa renda e, de certa forma chamar a atenção da sociedade para esta necessidade, ou seja, a de gerar mecanismos de melhoria da renda familiar. Através dos Postos de Troca, as pessoas residentes em comunidades atendidas pelo Programa Comunidade Eficiente, administrado pela Light junto a ANEEL, poderão trocar seus recicláveis por descontos em suas contas de energia elétrica. Os resíduos sólidos recicláveis possíveis por uma família de comunidade de baixa renda têm potencialidade em torno de 11,69 kg /mês, tendo sido estimada uma receita mensal por família de R$1,30. Este valor representa 40% da tarifa mínima cobrada pela Light, que é muito usual para esta classe de clientes. A viabilidade de implantação dos Postos de troca pode ser possível desde que haja um prazo mínimo para retorno do investimento de pelo menos 24 meses.

The effects of docks on seagrasses, with particular emphasis on the threatened seagrass, Halophila johnsonii

In March of 2005, the National Oceanic and Atmospheric Administration's Special Projects Office released "Population Trends along the Coastal United States: 1980-2008." This report includes population changes and trends between 1980 and 2003 and projected changes in coastal populations by 2008. Given the findings, pressure on coastal resources around the country will continue to rise, particularly in Florida. ... One of our most valuable coastal resources is seagrass, but human desire and need to live on the coast means that our habitat overlaps with suitable seagrass habitat. Seagrasses can be found in coastal areas around the world but are limited to relatively shallow, relatively clear water because of their reliance on light for photosynthesis. Seagrasses provide food for both small and large marine organisms, larval and adult stage. They provide shelter and habitat to a variety of commercially important fish and invertebrates. They baffle the water column and inhibit the resuspension of sediments. They prevent erosion and fix and recycle nutrients. The physical and ecological benefits of seagrasses make them very important to human welfare, but their light-limited coastal distribution makes them highly susceptible to anthropogenic influences.

Oyster mushroom waste as manure in fish culture: a preliminary study

In an attempt to recycle the waste substrates of the oyster-mushroom crop, tanks were stocked with seed of Indian major carp Cirrhinus mrigala at the rate of 600,000/ha and waste substrate was applied at weekly interval at 0, 50, 100, 150, 200 and 250 g/tank. Oyster mushroom waste not only provided highly nutritive colonised detritus to the fish as direct feed, but also produced rich plankton in the tank. In waste treated tanks, production was better than in the control in 150, 200 and 250 g/tank treatment suggesting the possibility of fish-oyster mushroom integration.

Integrating effluent management

The paper discusses a closed recycle shrimp farm in Thailand which integrates effluent management. The closed recycle system can reduce risk of heavy metals, pesticides, ammonia, and other toxic particles coming in with water from natural sources by reducing the quantity of water brought to the farm.

Energy recycling from multigigahertz clocks using fully integrated switching converters

Large digital chips use a significant amount of energy to broadcast a low-skew, multigigahertz clock to millions of latches located throughout the chip. Every clock cycle, the large aggregate capacitance of the clock network is charged from the supply and then discharged to ground. Instead of wasting this stored energy, it is possible to recycle the energy by controlling its delivery to another part of the chip using an on-chip dc-dc converter. The clock driver and switching converter circuits share many compatible characteristics that allow them to be merged into a single design and fully integrated on-chip. Our buck converter prototype, manufactured in 90-nm CMOS, provides a proof-of-concept that clock network energy can be recycled to other parts of the chip, thus lowering overall energy consumption. It also confirms that monolithic multigigahertz switching converters utilizing zero-voltage switching can be implemented in deep-submicrometer CMOS. With multigigahertz operation, fully integrated inductors and capacitors use a small amount of chip area with low losses. Combining the clock driver with the power converter can share the large MOSFET drivers necessary as well as being energy and space efficient. We present an analysis of the losses which we confirm by experimentally comparing the merged circuit with a conventional clock driver. © 2012 IEEE.

A combined nonfertile and UO2 PWR fuel assembly for actinide waste minimization

A new combined Non Fertile and Uranium (CONFU) fuel assembly is proposed to limit the actinides that need long-term high-level waste storage from the pressurized water reactor (PWR) fuel cycle. In the CONFU assembly concept, ∼20% of the UO2 fuel pins are replaced with fertile free fuel hosting the transuranic elements (TRUs) generated in the previous cycle. This leads to a fuel cycle sustainable with respect to net TRU generation, and the amount and radiotoxicity of the nuclear waste can be significantly reduced in comparison with the conventional once-through UO2 fuel cycle. It is shown that under the constraints of acceptable power peaking limits, the CONFU assembly exhibits negative reactivity feedback coefficients comparable in values to those of the reference UO2 fuel. Feasibility of the PWR core operation and control with complete TRU recycle has been shown based on full-core three-dimensional neutronic simulation. However, gradual buildup of small amounts of Cm and Cf challenges fuel reprocessing and fabrication due to the high spontaneous fission rates of these nuclides and heat generation by some Pu, Am, and Cm isotopes. Feasibility of the processing steps becomes more attainable if the time between discharge and reprocessing is 20 yr or longer.

A survey of alternative once-through fast reactor core designs

Reprocessing of Light Water Reactor (LWR) spent fuel to recover plutonium or transuranics for use in Sodium cooled Fast Reactors (SFRs) is a distant prospect in the U.S.A. This has motivated our evaluation of potentially cost-effective operation of uranium startup fast reactors (USFRs) in a once-through mode. This review goes beyond findings reported earlier based on a UC fueled MgO reflected SFR to describe a broader parametric study of options. Cores were evaluated for a variety of fuel/coolant/reflector combinations: UC/UZr/UO 2/UN;Na/Pb; MgO/SS/Zr. The challenge is achieving high burnup while minimizing enrichment and respecting both cladding fluence/dpa and reactivity lifetime limits. These parametric studies show that while UC fuel is still the leading contender, UO 2 fuel and ZrH 1.7 moderated metallic fuel are also attractive if UC proves to be otherwise inadequate. Overall, these findings support the conclusion that a competitive fuel cycle cost and uranium utilization compared to LWRs is possible for SFRs operated on a once-through uranium fueled fuel cycle. In addition, eventual transition to TRU recycle mode is studied, as is a small test reactor to demonstrate key features.

A sustainable PWR fuel cycle with complete TRU recycling using fertile-free fuel

The feasibility of a conventional PWR fuel cycle with complete recycling of TRU elements in the same reactor is investigated. A new Combined Non-fertile and Uranium (CONFU) fuel assembly where about 20% of the uranium fuel pins are replaced with fertile free fuel (FFF) hosting TRU generated in the previous cycle is proposed. In this sustainable fuel cycle based on the CONFU fuel assembly concept, the amount and radiotoxicity of the nuclear waste can be significantly reduced in comparison with the conventional once-through UO 2 fuel cycle. It is shown that under the constraints of acceptable power peaking limits, the CONFU assembly exhibits negative reactivity feedback coefficients comparable in values to those of the reference UO2 fuel. Moreover, the effective delayed neutron fraction is about the same as for UO2-fueled cores. Therefore, feasibility of the PWR core operation and control with complete TRU recycle has been shown in principle. However, gradual build up of small amounts of Cm and Cf challenges fuel reprocessing and fabrication due to the high spontaneous fissions rates of these nuclides and heat generation by some Pu, Am, and Cm isotopes. Feasibility of the processing steps becomes more attainable if the time between discharge and reprocessing is 20 years or longer. The implications for the entire fuel cycle will have to be addressed in future studies.

The closed thorium-transuranic fuel cycle in reduced-moderation PWRs and BWRs

Multiple recycle of long-lived actinides has the potential to greatly reduce the required storage time for spent nuclear fuel or high level nuclear waste. This is generally thought to require fast reactors as most transuranic (TRU) isotopes have low fission probabilities in thermal reactors. Reduced-moderation LWRs are a potential alternative to fast reactors with reduced time to deployment as they are based on commercially mature LWR technology. Thorium (Th) fuel is neutronically advantageous for TRU multiple recycle in LWRs due to a large improvement in the void coefficient. If Th fuel is used in reduced-moderation LWRs, it appears neutronically feasible to achieve full actinide recycle while burning an external supply of TRU, with related potential improvements in waste management and fuel utilization. In this paper, the fuel cycle of TRU-bearing Th fuel is analysed for reduced-moderation PWRs and BWRs (RMPWRs and RBWRs). RMPWRs have the advantage of relatively rapid implementation and intrinsically low conversion ratios, which is desirable to maximize the TRU burning rate. However, it is challenging to simultaneously satisfy operational and fuel cycle constraints. An RBWR may potentially take longer to implement than an RMPWR due to more extensive changes from current BWR technology. However, the harder neutron spectrum can lead to favourable fuel cycle performance. A two-stage TRU burning cycle, where the first stage is Th-Pu MOX in a conventional PWR feeding a second stage continuous burn in RMPWR or RBWR, is technically reasonable, although it is more suitable for the RBWR implementation. In this case, the fuel cycle performance is relatively insensitive to the discharge burn-up of the first stage. © 2013 Elsevier Ltd. All rights reserved.

FLUCTUATION OF SIZE-FRACTIONATED ALKALINE PHOSPHATASE AFTER BLOOM DISAPPEARANCE IN TWO SHALLOW PONDS

The temporal and vertical fluctuations of size fractionated alkaline phosphatase activity (APA) and kinetics parameters as well as orthophosphate (o-P) and chlorophyll concentrations were investigated after bloom disappearance in two shallow ponds A and B from 27 October 2001 to 15 April 2002. Pond A (Microcystis) bloomed seriously but pond B did not. The data of o-P and chlorophyll suggested that phosphorus was the principal limiting nutrimental element and its vertical flux should be regarded as an important driving factor for algal growth. In pond A, the accumulation of algae-derived detritus after bloom disappearance in overlying water stimulated excretion of algal fraction APA, mainly produced by attached bacteria responsible for detritus decomposition, whereas bacterial fraction APA preferred to function in surface water. Interestingly, completely contrary phenomena were observed in pond B. In season, even though no obvious difference for size-fractionated APA in both ponds, the total APA in pond A peaked earlier showing higher activity and efficiency (low K-m and high V-max values) as a result of algal-derived detritus input. In summary, it is suggested that the excretion of alkaline phosphatase with strongly catalyzing efficiency and high activity should be taken as important contributor to algal-derived detritus decomposition, further fueling nutrient recycle and accelerating algal development next year. Furthermore, some inhibitors and surfactants were testified to be good tools to identify the origin of dissolved alkaline phosphatase.

Study on the technology of thermal cracking of paraffin to alpha olefins

Alpha olefins are mainly produced from paraffin cracking in China, but their quality is not good because of bad quality of cracking feed and outdated technology. The technology of paraffin once-through cracking, paraffin recycle cracking of removing the heavy fraction after wax vaporizing and that of removing the heavy fraction before wax vaporizing were investigated in this paper. It was found that the technology of paraffin recycle cracking of removing the heavy fraction before wax vaporizing is new and better under the same operating conditions. Using hard paraffin (mp 54-56 degrees C) as feed, the high-quality alpha olefins products (C-5-C-21) containing more than 97 wt% of olefins and more than 88 wt% of alpha olefins are produced under optimum process conditions, which are a steam to paraffin ratio of 15 wt%, process temperature of 600 degrees C, low hydrocarbon partial pressure and residence time of 2 s. In addition, with the technology of the second injecting steam in ethylene cracking used in paraffin cracking, producing coke in paraffin cracking furnace has been markedly reduced.