Colloid probe AFM study of thermal collapse and protein interactions of poly(N-isopropylacrylamide) coatings

Graft coatings of poly(N-isopropylacrylamide) (pNIPAM) are of considerable interest for the reversible control of bio-interfacial interactions. In this study, graft coatings were prepared by free radical polymerisation from surface-bound polymerisable groups, on silicon wafers and quartz crystal microbalance (QCM) sensors. QCM with dissipation monitoring showed a gradual, extended phase change as the temperature increased. Colloid probe atomic force microscopy (CP-AFM) revealed a marked change in the compressibility of the coating below and above the lower critical solution temperature (LCST). Force curves showed an approximate 9-fold reduction in thickness between 24 °C and 38 °C, yet the collapsed coating at 38 °C still had a thickness significantly higher than the ellipsometrically determined dry thickness, indicating a residual extent of hydration above the LCST. At all temperatures, interaction force curves showed steric repulsion, though over different distances. There was little hysteresis between approach and retract force curves, which is evidence for almost instantaneous relaxation of the coating upon decompression. CP-AFM using a probe coated with bovine serum albumin (BSA) showed repulsive interactions with little approach/retraction hysteresis below the LCST, indicating lack of adhesion between the pNIPAM coating and the BSA-coated probe. In contrast, above the LCST the force curves on retraction were characteristic of adhesion, while the approach curves were still repulsive, and the adhesion increased in strength as the temperature was increased further beyond the LCST. Thus, QCM-D and CP-AFM data correlated well in showing a gradual nature of the phase transition and a concomitant gradual change in the interaction force with BSA.

A study on the photostability of photochromic fabrics from hybrid organosilica coatings

Photochromic fabrics were prepared using a coating solution containing photochromic dyes and silica sol-gel. The photochromic effect was rapid. The effect of three different post treatments on the optical and durability of the photochromic fabrics was evaluated. These included incorporating a UV stabilizer, increasing the surface hydrophobicity by fluorinating the pores, and blockading the dye-containing pores with additional silica coating. All the treatments improved photostability, without significantly affecting response/fading speeds.

One-step vapour-phase formation of patternable, electrically conductive, superamphiphobic coatings on fibrous materials

Patternable, electrically conductive coatings having a superhydrophobic and superoleophobic surface have been prepared by one-step vapour-phase polymerisation of polypyrrole in the presence of a fluorinated alkyl silane directly on fibrous substrates. The coated fabrics showed a surface resistance of 0.5-0.8 kΩ □^-1 with water and hexadecane contact angles of 165° and 154°, respectively.

Chromate replacement in coatings for corrosion protection of aerospace aluminium alloys

Mixed rare earth organophosphates have been investigated as potential corrosion inhibitors for AA2024-T3 with the aim of replacing chromate-based technologies. Cerium diphenyl phosphate (Ce(dpp) 3) and mischmetal diphenyl phosphate (Mm(dpp) 3) were added to epoxy coatings applied to AA2024-T3 panels and they were effective in reducing the amount and rate of filiform corrosion in high humidity conditions. Ce(dpp) 3 was the most effective and characterisation of the coating formulations showed approximately a factor of 5 reduction in both the number of corrosion filaments initiated as well as the length of these. Mm(dpp) 3 appeared to reduce the corrosion growth rate by a factor of 2 although it was the more effective inhibitor in solution studies. Spectroscopic characterisation of the coatings indicated that the cerium based inhibitor may disrupt network formation in the epoxy thus resulting in a coating that absorbed more water and allowed greater solubilisation of the corrosion inhibiting compound.

Studying and evaluating anti-corrosion coatings and inhibitors using the wire beam electrode method in conjunction with electrochemical noise analysis

Purpose – To provide a summary of research work carried out mainly in the authors' group for evaluating various protective coatings including rustproofing oils, and also for studying corrosion inhibitors using the wire beam electrode (WBE) method.

Design/methodology/approach – A range of published papers published during the past 15 years was summarised and reviewed. Recent research work in the authors' group was also included, which involved the combined use of the WBE with electrochemical noise analysis and the scanning reference electrode technique.

Findings – The WBE method has been developed into a very useful tool of evaluating the performance of coatings and inhibitors. In particular, The WBE is uniquely applicable for determining the performance of coatings and inhibitors to control localised corrosion.

Research limitations/implications – Focusing mainly on recent research.

Practical implications – A useful source of information for researchers and graduate students working in the areas of organic coating and inhibitor research.

Originality/value – The first summary or review on this research topic.