Magnetic switching and anisotropy in nanomagnets: the influence of size and shape

Arrays of nanomagnets were fabricated out of Ni80Fe14Mo5 in the lateral size range 500-30nm and the thickness range 3-20nm. Elliptical, triangular, square, pentagonal and circular geometries were all considered. The magnetic properties of these nanomagnets were probed rapidly and non-invasively using a high sensitivity magneto-optical method.

Monitoring A Micromechanical Process In Macroscale Carbon Nanotube Films And Fibers

The evaluation of mechanical properties of carbon nanotube (CNT) fibers is inherently difficult. Here, Raman scattering-a generic methodology independent of mechanical measurements-is used to determine the interbundle strength and microscopic failure process for various CNT macroarchitectures. Raman data are used to predict the moduli of CNT films and fibers, and to illustrate the influences of the twisting geometries on the fibers' mechanical performances.

Geometria et Geometriae : e mathematica ad philosopiam

Resumen: Luego de exponer las posibilidades filosóficas que las geometrías abren a las orientaciones de nuevos espacios, el artículo considera los procedimientos euclidianos y la conexión con las geometrías no-euclidianas. Hay muchas posiciones acerca de las bases filosóficas de las distintas geometrías. Hay además formulaciones muy importantes, desde la gnoseología a la ontología, respecto de las extensiones métricas de la alta geometría.

Shock slip-relations for thermal and chemical nonequilibrium flows

This paper appears to be the first where the multi-temperature shock slip-relations for the thermal and chemical nonequilibrium flows are derived. The derivation is based on analysis of the influences of thermal nonequilibrium and viscous effects on the mass, momentum and energy flux balance relations at the shock wave. When the relaxation times for all internal energy modes tend to sere, the multi-temperature shock slip-relations are converted into single-temperature ones for thermal equilibrium hows. The present results can be applied to flows over vehicles of different geometries with or without angles of attack. In addition, the present single-temperature shock slip-relations are compared with those in the literature, and Some defects and limitations in the latter are clarified.

Experimental Studies on Model Scramjet in a Mach 6 High Enthalpy Free-Jet Wind Tunnel

A side-wall compression scramjet model with different combustor geometries has been tested in a propulsion tunnel that typically provides the testing flow with Mach number of 5.8, total temperature of 1800K, total pressure of 4.5MPa and mass flow rate of 4kg/s. This kerosene-fueled scramjet model consists of a side-wall compression inlet, a combustor and a thrust nozzle. A strut was used to increase the contraction ratio and to inject fuels, as well as a mixing enhancement device. Several wall cavities were also employed for flame-holding. In order to shorten the ignition delay time of the kerosene fuel, a little amount of hydrogen was used as a pilot flame. The pressure along the combustor has an evident raise after ignition occurred. Consequently thrust was observed during the fuel-on period. However, the thrust was still less than the drag of the scramjet model. For this reason, the drag variation produced by different strut and cavities was tested. Typical results showed that the cavities do not influence the drag so much, but the length of the strut does.

3D Finite Volume Scheme for Czochralski Single Crystal Growth

Czochralski (Cz) technique, which is used for growing single crystals, has dominated the production of single crystals for electronic applications. The Cz growth process involves multiple phases, moving interface and three-dimensional behavior. Much has been done to study these phenomena by means of numerical methods as well as experimental observations. A three-dimensional curvilinear finite volume based algorithm has been developed to model the Cz process. A body-fitted transformation based approach is adopted in conjunction with a multizone adaptive grid generation (MAGG) technique to accurately handle the three-dimensional problems of phase-change in irregular geometries with free and moving surfaces. The multizone adaptive model is used to perform a three-dimensional simulation of the Cz growth of silicon single crystals.Since the phase change interface are irregular in shape and they move in response to the solution, accurate treatment of these interfaces is important from numerical accuracy point of view. The multizone adaptive grid generation (MAGG) is the appropriate scheme for this purpose. Another challenge encountered is the moving and periodic boundary conditions, which is essential to the numerical solution of the governing equations. Special treatments are implemented to impose the periodic boundary condition in a particular direction and to determine the internal boundary position and shape varying with the combination of ambient physicochemical transport process and interfacial dynamics. As indicated above that the applications and processes characterized by multi-phase, moving interfaces and irregular shape render the associated physical phenomena three-dimensional and unsteady. Therefore a generalized 3D model rather than a 2D simulation, in which the governing equations are solved in a general non-orthogonal coordinate system, is constructed to describe and capture the features of the growth process. All this has been implemented and validated by using it to model the low pressure Cz growth of silicon. Accuracy of this scheme is demonstrated by agreement of simulation data with available experimental data. Using the quasi-steady state approximation, it is shown that the flow and temperature fields in the melt under certain operating conditions become asymmetric and unsteady even in the absence of extrinsic sources of asymmetry. Asymmetry in the flow and temperature fields, caused by high shear initiated phenomena, affects the interface shape in the azimuthal direction thus results in the thermal stress distribution in the vicinity, which has serious implications from crystal quality point of view.

Squaring the circle. Social and environmental implications of pre-pottery neolithic building technology at Tell Qarassa (South Syria)

We present the results of the microstratigraphic, phytolith and wood charcoal study of the remains of a 10.5 ka roof. The roof is part of a building excavated at Tell Qarassa (South Syria), assigned to the Pre-Pottery Neolithic B period (PPNB). The Pre-Pottery Neolithic (PPN) period in the Levant coincides with the emergence of farming. This fundamental change in subsistence strategy implied the shift from mobile to settled aggregated life, and from tents and huts to hard buildings. As settled life spread across the Levant, a generalised transition from round to square buildings occurred, that is a trademark of the PPNB period. The study of these buildings is fundamental for the understanding of the ever-stronger reciprocal socio-ecological relationship humans developed with the local environment since the introduction of sedentism and domestication. Descriptions of buildings in PPN archaeological contexts are usually restricted to the macroscopic observation of wooden elements (posts and beams) and mineral components (daub, plaster and stone elements). Reconstructions of microscopic and organic components are frequently based on ethnographic analogy. The direct study of macroscopic and microscopic, organic and mineral, building components performed at Tell Qarassa provides new insights on building conception, maintenance, use and destruction. These elements reflect new emerging paradigms in the relationship between Neolithic societies and the environment. A square building was possibly covered here with a radial roof, providing a glance into a topologic shift in the conception and understanding of volumes, from round-based to square-based geometries. Macroscopic and microscopic roof components indicate buildings were conceived for year-round residence rather than seasonal mobility. This implied performing maintenance and restoration of partially damaged buildings, as well as their adaptation to seasonal variability

Manipulation of domain wall dynamics in amorphous microwires through the magnetoelastic anisotropy

We studied the effect of magnetoelastic anisotropy on domain wall (DW) dynamics and remagnetization process of magnetically bistable Fe-Co-rich microwires with metallic nucleus diameters (from 1.4 to 22 mu m). We manipulated the magnetoelastic anisotropy applying the tensile stresses and changing the magnetostriction constant and strength of the internal stresses. Microwires of the same composition of metallic nucleus but with different geometries exhibit different magnetic field dependence of DW velocity with different slopes. Application of stresses resulted in decrease of the DW velocity, v, and DW mobility, S. Quite fast DW propagation (v until 2,500 m/s at H about 30 A/m) has been observed in low magnetostrictive magnetically bistable Co56Fe8Ni10Si10B16 microwires. Consequently, we observed certain correlation between the magnetoelastic energy and DW dynamics in microwires: decreasing the magnetoelastic energy, K (me), DW velocity increases.

Domain wall dynamics of magnetically bistable microwires

EMM-FM2011 – First Euro Mediterranean Meeting on Functionalized Materials, edited by Cheikhrouhou, A. 1st Euro Mediterranean Meeting on Functionalized Materials (EMM-FM). Sousse, TUNISIA . Sep. 06-10, 2011

Zum tierschutzgerechten Betäuben und Töten von Aal

Slaughtering of eels should be done not only under animal welfare aspects but as well under consumer protection and economical aspects with respect to technical feasibility. Methods must be practicable for enterprises slaughtering quantities of several kilograms up to several tons per day. Most methods applied up to now in whole Europe were (are) not in accordance with animal welfare mainly due to lacking prescriptions and alternative methods. The great number of experiments carried out within the frame of this project demonstrates the difficulties to combine optimal welfare demands with economical and technical fesibility aspects in one method. Measurements of EEG (electroencephalogram) and ECG (electrocardiogram) have shown that the method laid down in the german legislation does not perfectly stun all eels. This method was improved by applying a „prestun“ with 220 V for 1sec., followed by a 5 min phase at 45 V to prolongue the time of unconsciousness after the stun. Inflating nitrogen gas into the stunning bath additionally causes asphyxia during the stun. By this method 93% of the eels were stunned or even killed. Applying 220 V for bigger batches of eels (~400 kg) will cause big problems with the energy supply. Therefore this method is restricted to batches of 20 - 50 kg. The method laid down in the german legislation probably can be improved. Eels were stunned successfully without water, avoiding the problems of regional differences in the conductivity of the water. Other types of current and other frequencies and a combination of both should be tested as well as alternative electrode geometries also with respect to blood spots which occasionally occurred in the muscles preferably of bigger eels (>800 g). For the time being the method laid down in the german legislation is a reasonable compromise and under animal welfare aspects represents a considerable improvement.

Microfluidic Rheometry

The development and growth of microfluidics has stimulated interest in the behaviour of complex liquids in micro-scale geometries and provided a rich platform for rheometric investigations of non-Newtonian phenomena at small scales. Microfluidic techniques present the rheologist with new opportunities for material property measurement and this review discusses the use of microfluidic devices to measure bulk rheology in both shear and extensional flows. Capillary, stagnation and contraction flows are presented in this context and developments, limitations and future perspectives are examined. (C) 2008 Elsevier Ltd. All rights reserved.

An Instrumented Indentation Method for Young's Modulus Measurement with Accuracy Estimation

The relationships between indentation responses and Young's modulus of an indented material were investigated by employing dimensional analysis and finite element method. Three representative tip bluntness geometries were introduced to describe the shape of a real Berkovich indenter. It was demonstrated that for each of these bluntness geometries, a set of approximate indentation relationships correlating the ratio of nominal hardness/reduced Young's modulus H (n) /E (r) and the ratio of elastic work/total work W (e)/W can be derived. Consequently, a method for Young's modulus measurement combined with its accuracy estimation was established on basis of these relationships. The effectiveness of this approach was verified by performing nanoindentation tests on S45C carbon steel and 6061 aluminum alloy and microindentation tests on aluminum single crystal, GCr15 bearing steel and fused silica.

Topics in vortex motion

Six topics in incompressible, inviscid fluid flow involving vortex motion are presented. The stability of the unsteady flow field due to the vortex filament expanding under the influence of an axial compression is examined in the first chapter as a possible model of the vortex bursting observed in aircraft contrails. The filament with a stagnant core is found to be unstable to axisymmetric disturbances. For initial disturbances with the form of axisymmetric Kelvin waves, the filament with a uniformly rotating core is neutrally stable, but the compression causes the disturbance to undergo a rapid increase in amplitude. The time at which the increase occurs is, however, later than the observed bursting times, indicating the bursting phenomenon is not caused by this type of instability.

In the second and third chapters the stability of a steady vortex filament deformed by two-dimensional strain and shear flows, respectively, is examined. The steady deformations are in the plane of the vortex cross-section. Disturbances which deform the filament centerline into a wave which does not propagate along the filament are shown to be unstable and a method is described to calculate the wave number and corresponding growth rate of the amplified waves for a general distribution of vorticity in the vortex core.

In Chapter Four exact solutions are constructed for two-dimensional potential flow over a wing with a free ideal vortex standing over the wing. The loci of positions of the free vortex are found and the lift is calculated. It is found that the lift on the wing can be significantly increased by the free vortex.

The two-dimensional trajectories of an ideal vortex pair near an orifice are calculated in Chapter Five. Three geometries are examined, and the criteria for the vortices to travel away from the orifice are determined.

Finally, Chapter Six reproduces completely the paper, "Structure of a linear array of hollow vortices of finite cross-section," co-authored with G. R. Baker and P. G. Saffman. Free streamline theory is employed to construct an exact steady solution for a linear array of hollow, or stagnant cored vortices. If each vortex has area A and the separation is L, then there are two possible shapes if A^(1/2)/L is less than 0.38 and none if it is larger. The stability of the shapes to two-dimensional, periodic and symmetric disturbances is considered for hollow vortices. The more deformed of the two possible shapes is found to be unstable, while the less deformed shape is stable.

Synthesis, structure, and photophysics of polypyridophenazine transition-metal complexes

The condensation of phenanthroline-5,6-dione (phendione) with polyamines is a versatile synthetic route to a wide variety of chelating ligands. Condensation with 2,3- napthalene diamine gives benzo[i]dipyrido[3,2-a:2',3'-c]phenazine (bdppz) a ligand containing weakly-coupled orbitals of benzophenazine (bpz) and 2,2' -bipyridinde(bpy) character. The bpy character gives Re and Ru complexes excited-state redox properties; intramolecular electron transfer (ET) takes place to the bpz portion of the ligand. The charge-separated state so produced has an extraordinarily-long 50 µs lifetime. The slow rate of charge recombination arises from a combination of extremely weak coupling between the metal center and the bpz acceptor orbital and Marcus "inverted region" behavior. Molecular orbital calculations show that only 3% the electron density in the lowest unoccupied molecular orbital lies on the bpy atoms of bdppz, effectively trapping the transferred electron on the bpz portion. The rate of charge recombination decreases with increasing driving force, showing that these rates lie in the inverted region. Comparison of forward and back ET rates shows that donor-acceptor coupling is four orders of magnitude greater for photoinduced electron transfer than it is for thermal charge recombination.

Condensation of phendione with itself or tetramines gives a series of binucleating tetrapyridophenazine ligands of incrementally-varying coordination-site separation. When a photoredox-active metal center is attached, excited-state energy and electron transfer to an acceptor metal center at the other coordination site can be studied as a function of distance. A variety of monometallic and homo- and heterodimetallic tetrapyridophenazine complexes has been synthesized. Electro- and magnetochemistry show that no ground-state interaction exists between the metals in bimetallic complexes. Excited-state energy and electron transfer, however, takes place at rates which are invariant with increasing donor-acceptor separation, indicating that a very efficient coupling mechanism is at work. Theory and experiment have suggested that such behavior might exist in extended π-systems like those presented by these ligands.

Condensation of three equivalents of 4,5-dimethyl-1,2-phenylenediamine with hexaketocyclohexane gives the trinucleating ligand hexaazahexamethyltrinapthalene (hhtn). Attaching two photredox-active metal centers and a third catalytic center to hhtn provides means by which multielectron photocatalyzed reactions might be carried out. The coordination properties of hhtn have been examined; X-ray crystallographic structure determination shows that the ligand's constricted coordination pocket leads to distorted geometries in its mono- and dimetallic derivatives.

Dirac spectra, summation formulae, and the spectral action

Noncommutative geometry is a source of particle physics models with matter Lagrangians coupled to gravity. One may associate to any noncommutative space (A, H, D) its spectral action, which is defined in terms of the Dirac spectrum of its Dirac operator D. When viewing a spin manifold as a noncommutative space, D is the usual Dirac operator. In this paper, we give nonperturbative computations of the spectral action for quotients of SU(2), Bieberbach manifolds, and SU(3) equipped with a variety of geometries. Along the way we will compute several Dirac spectra and refer to applications of this computation.