KINETICS OF MASS LOSS OF ARABICA COFFEE DURING ROASTING PROCESS

ABSTRACT Roasting is one of the most complex coffee processing steps due to simultaneous transfers of heat and mass. During this process, beans lose mass because of fast physical and chemical changes that will set color and flavor of the commercial coffee beverage. Therefore, we aimed at assessing the kinetics of mass loss in commercially roasted coffee beans according to heating throughout the processing. For that, we used samples of 350-g Arabica coffee processed grains with water content of 0.1217 kga kg-1, in addition to a continuous roaster with firing gas. The roaster had initial temperatures of 285, 325, 345 and 380 °C, decreasing during the process up to 255, 285, 305 and 335 °C respectively. Mass loss was calculated by the difference between grain weight before and after roasting. We observed a linear variation directly dependent on roaster temperature. For each temperature during the process was obtained a constant mass loss rate, which was reported by the Arrhenius model with r2 above 0.98. In a roaster in non-isothermal conditions, the required activation energy to start the mass loss in a commercial coffee roasting index was 52.27 kJ mol -1.

Quasiclassical Approach to the Vortex State in Iron-based Superconductors

The quasiclassical approach was applied to the investigation of the vortex properties in the ironbased superconductors. The special attention was paid to manifestation of the nonlocal effects of the vortex core structure. The main results are as follows: (i) The effects of the pairing symmetries (s+ and s₊₊) on the cutoff parameter of field distribution, ξh, in stoichiometric (like LiFeAs) and nonstoichiometric (like doped BaFe₂As₂) iron pnictides have been investigated using Eilenberger quasiclassical equations. Magnetic field, temperature and impurity scattering dependences of ξh have been calculated. Two opposite behavior have been discovered. The ξh /ξc2 ratio is less in s+ symmetry when intraband impurity scattering (Γ₀) is much larger than one and much larger than interband impurity scattering (Γπ), i.e. in nonstoichiometric iron pnictides. Opposite, the value ξh /ξc2 is higher in s+ case and the field dependent curve is shifted upward from the "clean" case (Γ₀ = Γπ = 0) for stoichiometric iron pnictides (Γ₀ = Γπ ≪ 1). (ii) Eilenberger approach to the cutoff parameter, ξh, of the field distribution in the mixed state of high

Manifestation of the pairing symmetry in the vortex core structure in iron-based superconductors

The superconducting gap is a basic character of a superconductor. While the cuprates and conventional phonon-mediated superconductors are characterized by distinct d- and s-wave pairing symmetries with nodal and nodeless gap distributions respectively, the superconducting gap distributions in iron-based superconductors are rather diversified. While nodeless gap distributions have been directly observed in Ba1–xKxFe2As2, BaFe2–xCoxAs2, LiFeAs, KxFe2–ySe2, and FeTe1–xSex, the signatures of a nodal superconducting gap have been reported in LaOFeP, LiFeP, FeSe, KFe2As2, BaFe2–xRuxAs2, and BaFe2(As1–xPx)2. Due to the multiplicity of the Fermi surface in these compounds s± and d pairing states can be both nodeless and nodal. A nontrivial orbital structure of the order parameter, in particular the presence of the gap nodes, leads to effects in which the disorder is much richer in dx2–y2-wave superconductors than in conventional materials. In contrast to the s-wave case, the Anderson theorem does not work, and nonmagnetic impurities exhibit a strong pair-breaking influence. In addition, a finite concentration of disorder produces a nonzero density of quasiparticle states at zero energy, which results in a considerable modification of the thermodynamic and transport properties at low temperatures. The influence of order parameter symmetry on the vortex core structure in iron-based pnictide and chalcogenide superconductors has been investigated in the framework of quasiclassical Eilenberger equations. The main results of the thesis are as follows. The vortex core characteristics, such as, cutoff parameter, ξh, and core size, ξ2, determined as the distance at which density of the vortex supercurrent reaches its maximum, are calculated in wide temperature, impurity scattering rate, and magnetic field ranges. The cutoff parameter, ξh(B; T; Г), determines the form factor of the flux-line lattice, which can be obtained in _SR, NMR, and SANS experiments. A comparison among the applied pairing symmetries is done. In contrast to s-wave systems, in dx2–y2-wave superconductors, ξh/ξc2 always increases with the scattering rate Г. Field dependence of the cutoff parameter affects strongly on the second moment of the magnetic field distributions, resulting in a significant difference with nonlocal London theory. It is found that normalized ξ2/ξc2(B/Bc2) dependence is increasing with pair-breaking impurity scattering (interband scattering for s±-wave and intraband impurity scattering for d-wave superconductors). Here, ξc2 is the Ginzburg-Landau coherence length determined from the upper critical field Bc2 = Φ0/2πξ2 c2, where Φ0 is a flux quantum. Two types of ξ2/ξc2 magnetic field dependences are obtained for s± superconductors. It has a minimum at low temperatures and small impurity scattering transforming in monotonously decreasing function at strong scattering and high temperatures. The second kind of this dependence has been also found for d-wave superconductors at intermediate and high temperatures. In contrast, impurity scattering results in decreasing of ξ2/ξc2(B/Bc2) dependence in s++ superconductors. A reasonable agreement between calculated ξh/ξc2 values and those obtained experimentally in nonstoichiometric BaFe2–xCoxAs2 (μSR) and stoichiometric LiFeAs (SANS) was found. The values of ξh/ξc2 are much less than one in case of the first compound and much more than one for the other compound. This is explained by different influence of two factors: the value of impurity scattering rate and pairing symmetry.

α-Pinene oxide and verbenol oxide isomerizations over heterogeneous catalysts

Terpenes are a valuable natural resource for the production of fine chemicals. Turpentine, obtained from biomass and also as a side product of softwood industry, is rich in monoterpenes such as α-pinene and β-pinene, which are widely used as raw materials in the synthesis of flavors, fragrances and pharmaceutical compounds. The rearrangement of their epoxides has been thoroughly studied in recent years, as a method to obtain compounds which are further used in the fine chemical industry. The industrially most desired products of α-pinene oxide isomerization are campholenic aldehyde and trans-carveol. Campholenic aldehyde is an intermediate for the manufacture of sandalwood-like fragrances such as santalol. Trans-carveol is an expensive constituent of the Valencia orange essence oil used in perfume bases and food flavor composition. Furthermore it has been found to exhibit chemoprevention of mammary carcinogenesis. A wide range of iron and ceria supported catalysts were prepared, characterized and tested for α-pinene oxide isomerization in order to selective synthesis of above mentioned products. The highest catalytic activity in the preparation of campholenic aldehyde over iron modified catalysts using toluene as a solvent at 70 °C (total conversion of α-pinene oxide with a selectivity of 66 % to the desired aldehyde) was achieved in the presence of Fe-MCM-41. Furthermore, Fe-MCM-41 catalyst was successfully regenerated without deterioration of catalytic activity and selectivity. The most active catalysts in the synthesis of trans-carveol from α-pinene oxide over iron and ceria modified catalysts in N,N-dimethylacetamide as a solvent at 140 °C (total conversion of α-pinene oxide with selectivity 43 % to trans-carveol) were Fe-Beta-300 and Ce-Si-MCM-41. These catalysts were further tested for an analogous reaction, namely verbenol oxide isomerization. Verbenone is another natural organic compound which can be found in a variety of plants or synthesized by allylic oxidation of α-pinene. An interesting product which is synthesized from verbenone is (1R,2R,6S)-3-methyl-6-(prop-1-en-2-yl)cyclohex-3-ene-1,2-diol. It has been discovered that this diol possesses potent anti-Parkinson activity. The most effective way leading to desired diol starts from verbenone and includes three stages: epoxidation of verbenone to verbenone oxide, reduction of verbenone oxide and subsequent isomerization of obtained verbenol oxide, which is analogous to isomerization of α-pinene oxide. In the research focused on the last step of these synthesis, high selectivity (82 %) to desired diol was achieved in the isomerization of verbenol oxide at a conversion level of 96 % in N,N-dimethylacetamide at 140 °C using iron modified zeolite, Fe-Beta-300. This reaction displayed surprisingly high selectivity, which has not been achieved yet. The possibility of the reuse of heterogeneous catalysts without activity loss was demonstrated.

Análise espectrofotométrica da ação das lipoxigenases em grãos de soja macerados em diferentes temperaturas

O sabor e aroma desagradáveis dos derivados da soja, particularmente do extrato hidrossolúvel (leite de soja), são obstáculos a sua aceitação pelos ocidentais que o consideram desagradável. A origem desse "flavor" está na oxidação de ácidos graxos catalisada pelas isoenzimas lipoxigenases quando os tecidos dos grãos sofrem danos na presença de umidade. Já na maceração (embebição) dos grãos, no processo tradicional de produção de leite de soja, células do cotilédone sofrem rupturas, devido ao entumescimento provocado pela rápida absorção de água, permitindo o contato enzima-substrato. O objetivo do presente estudo foi avaliar o nível de oxidação sofrido por grãos de soja macerados em diferentes temperaturas, e depois liofilizados, para a extração e análise espectrofotométrica (232 nm) da fração lipídica. Os métodos de extração e análise empregados permitiram a verificação da ocorrência de oxidação no processo de maceração sendo que o coeficiente de extinção (dienos conjugados) passou de 3,40 [(g/100ml)cm]-1 (grãos não macerados) para 5,88 [(g/100ml)cm]-1 (grãos macerados a 22°C) e o coeficiente de extinção diminuiu com o aumento da temperatura.

Concentração de suco de laranja (Citrus sinensis) por osmose inversa

A concentração de suco de laranja por osmose inversa combinada com ultrafiltração foi estudada em escala semi-piloto, visando avaliar a utilização dessa tecnologia para substituição parcial da evaporação. Foram utilizados no processamento 100 litros de suco de laranja, com teor de polpa de 1,5%, cedidos pela CTM Citrus. Na primeira etapa, todo o suco passou pela etapa de ultrafiltração, para separação da polpa, enzimas pectinolíticas e microrganismos, que foram retidos. Foi utilizada uma membrana da Romicom (HF-43) de polissulfona em um sistema de configuração tubular, com peso molecular de corte de 50.000 daltons, à pressão de 1,2 bar. Obteve-se um fator de concentração de 27,6. O retentado da ultrafiltração foi pasteurizado à temperatura de 90°C, em trocador de calor de superfície raspada desenvolvido para este projeto. O processo de osmose inversa foi conduzido no equipamento Lab-unit M-20 da DDS, utilizando membranas da DDS (HR 95 PP) de filme composto em um sistema de configuração quadro e placas. Foram realizados três tratamentos com pressões de 20, 40 e 60 bar e para cada experimento, foram feitas três repetições. O retentado pasteurizado da ultrafiltração foi adicionado ao retentado da osmose inversa e caracterizado química, física e sensorialmente. Na osmose inversa foram obtidos fatores de concentração de 2,7, 3,5 e 3,6 e teores de sólidos solúveis de 18, 23 e 30 °Brix, para os tratamentos de 20, 40 e 60 bar, respectivamente. Os respectivos permeados apresentaram teores de sólidos solúveis de 3,3, 1,3 e 0,3°Brix e acidez de 262,50, 91,50 e 34,25 mg de ácido cítrico/100 ml. Os sucos obtidos pelos três tratamentos apresentaram valores de "defect score" e "color score" superiores aos do suco original, enquanto que para o "flavor score", os sucos obtidos às pressões de 40 e 60 bar, apresentaram valores próximos ao ideal. Os valores de "ratio", pH e formol foram semelhantes entre os tratamentos. O teor de óleo foi maior no tratamento realizado à menor pressão enquanto que o teor de vitamina C foi maior no de maior pressão. Tanto o suco concentrado quanto o diluído, nos três tratamentos, foram caracterizados como fluidos Newtonianos, apresentando valores de viscosidade maiores quando obtidos a maiores pressões.

Organic acid profile of commercial sour cassava starch

Organic acids are present in sour cassava starch ("polvilho azedo") and contribute with organoleptic and physical characteristics like aroma, flavor and the exclusive baking property, that differentiate this product from the native cassava starch. Samples of commercial sour cassava starch collected in South and Southeast Brazil were prepared for high performance liquid chromatography (HPLC) analysis. The HPLC equipment had a Biorad Aminex HPX-87H column for organic acid analysis and a refractometric detector. Analysis was carried out with 0.005M sulfuric acid as mobile phase, 0.6ml/min flow rate and column temperature of 60° C. The acids quantified were lactic (0.036 to 0.813 g/100g), acetic (0 to 0.068 g/100g), propionic (0 to 0.013 g/100g) and butyric (0 to 0.057 g/100g), that are produced during the natural fermentation of cassava starch. Results showed large variation among samples, even within the same region. Some samples exhibited high acid levels, mainly lactic acid, but in these neither propionic nor butyric acids were detected. Absence of butyric acid was not expected because this is an important component of the sour cassava starch aroma, and the lack of this acid may suggest that such samples were produced without the natural fermentation step.

Substâncias voláteis em mel floral e mel de melato

Embora pareça existir um "flavor" característico de mel, a grande variedade de flores disponíveis para a abelha, possibilita uma grande diversidade de flavor e aroma, indicando a presença de vários componentes voláteis. Alguns destes dependem da fisiologia da abelha, dos procedimentos após a colheita e no mel de melato há também a interferência de insetos sugadores e das formigas. Várias substâncias voláteis já foram identificadas, sendo algumas características de determinados méis uniflorais. Com o objetivo de encontrar uma substância volátil característica do mel de melato, seis amostras deste tipo de mel e seis amostras de mel floral foram analisadas usando extração por arraste de gás hidrogênio e cromatografia a gás acoplada a espectrometria de massas. Ácido acético foi encontrado em quatro amostras de mel de melato e em uma amostra de mel floral porém, com menor abundância.

Electrophoretic analisys to detect and quantify additional whey in milk and dairy beverages

Polyacrylamide gel electrophoresis, SDS-PAGE system, was adjusted to detect the presence of additional whey in dairy beverages distributed in a Brazilian Government School Meals Program. Aqueous solutions of samples in 8 M urea were submitted to a polyacrylamide gel gradient (10% to 18%). Gel scans from electrophoresis patterns of previously adulterated milk samples showed that caseins peak areas decreased while peak areas of beta -lactoglobulin plus alpha -lactalbumin increased as the percentage of raw milk powder replaced by whey powder increased. The relative densitometer areas of caseins or beta -lactoglobulin plus alpha -lactalbumin plotted against the percentage of whey added to the raw milk showed a linear correlation coefficient square higher than 0.97. The caseins plot was used to determine the percentage of additional whey in 116 dairy beverages, chocolate or coffee flavor. Considering that the lowest relative caseins concentration found in commercial milk powder samples by the present method was 72%, the dairy beverages containing caseins percentages equal to or higher than this value were considered free of additional whey. Based on this criterion, about 49% of the coffee-flavor dairy beverages and 29% of the chocolate-flavor beverages, among all the samples analyzed were adulterated with whey protein to reach the total protein contents specified on their labels. The present method showed a sensitivity of 5% to additional whey.

USO DE CULTURAS INICIADORAS PARA A ELABORAÇÃO DE UM EMBUTIDO À BASE DE CARNE DE PATO (Cairina moschata)

No Brasil, tanto a criação quanto a comercialização da carne de pato (Cairina moschata) ainda é incipiente, mas devido a sua rusticidade, fácil manejo, e carne apreciada no mercado, entende-se que a obtenção de produtos à base de carne de pato apresenta-se como uma alternativa rentável na indústria de alimentos. O uso de culturas iniciadoras na elaboração de produtos fermentados é uma prática comum na indústria de produtos cárneos estando diretamente relacionada às características de flavor, textura, cor e vida-de-prateleira do produto final. Avaliou-se o uso de culturas iniciadoras na elaboração de embutido fermentado à base de carne de pato obtida da desossa manual da coxa e sobrecoxa. Uma mistura de culturas iniciadoras de Lactobacillus plantarum BN e Kokuria varians CCT 4492 foi usada para inocular a massa cárnea. Os embutidos foram defumados em câmara para defumação a 23±1°C por aproximadamente 19 horas e curados por 25 dias. A contagem inicial de células viáveis na massa do embutido foi de 6,08Log10UFC/g e de 6,04Log10UFC/g para bactérias ácido-lácticas e Micrococcacea, respectivamente. Após o segundo dia do processo, bactérias ácido-lácticas apresentaram um crescimento de 0,79 ciclos logarítmicos e no décimo primeiro dia um aumento de 2,58 ciclos logarítmicos. O valor médio de acidez, em ácido láctico, no produto final foi de 0,39% e o valor de pH de 5,11. As análises físico-químicas apresentaram-se dentro dos padrões da legislação brasileira. O produto elaborado apresentou perfil sensorial dentro dos padrões aceitáveis de qualidade.

Brazilian roasted coffee oil obtained by mechanical expelling: compositional analysis by GC-MS

A preliminary analysis by GC-MS comparing the mass spectrum of the compounds with the Wiley 275 L mass spectral data base was used to identify the fatty acids and mainly, some volatile compounds responsible for the flavor of the roasted coffee oil. The oil was obtained by mechanical expelling of Brazilian beans (Coffea arabica) roasted at 238ºC for 10 minutes. Different sample preparation methodologies such as headspace, adsorbent suction trapping and esterification were used. It was possible to identify pyrazines, pyridines, furan derivatives and other compounds not reported in the literature.

Efeito do cozimento na qualidade do músculo Semitendinosus

O presente experimento foi realizado para determinar a efetividade do tratamento térmico em água e vapor a 80 °C tendo como objetivo a inativação do Clostridium botulinum tipo E, utilizando-se amostras de Semintendinosus. Foram realizadas ainda a avaliação da maciez objetiva, utilizando-se a análise de força de cisalhamento, e a avaliação sensorial dos atributos de suculência, maciez subjetiva, "flavor" e presença de colágeno. O tratamento a 80 °C foi efetivo na eliminação do microrganismo, contudo não houve diferença significativa no atributo maciez objetiva (força de cisalhamento) avaliado nos dois tratamentos utilizados. A avaliação sensorial apresentou correlação positiva entre os atributos maciez e suculência, enquanto o colágeno apresentou correlação negativa com a maciez. O "flavor" não apresentou correlação com os atributos maciez, suculência e presença de colágeno.

Development and assessment of acceptability and nutritional properties of a light snack

A light snack was developed using a fat replacer as a flavor fixative agent. The product presented a calorie reduction of up to 47.5% in comparison with products available on the market. The impact of this fat replacer on the sensory properties was determined by comparing this light snack to the traditional ones. No significant difference in texture was observed; however, there was a difference in color (deltaE = 8.67), due mainly to luminosity (deltaL = 7.79). The light snack presented high sensory acceptability (7.27 ± 1.3; 82.5% of grades were > 7 on 9-point hedonic scale); no significant difference in snack acceptability was observed. However, the traditional snack was significantly preferred in sensory terms (p < 0.05). In an opinion survey when the consumers were informed about snack composition, 75% of them said that they would buy the light snack instead of the traditional one. The caloric and fat reductions allow the use of the claims "light snack" and "fat free", in accordance with the legislation of various countries. We conclude that it is technologically possible to use a fat replacer in snack production, resulting in a sensory acceptable light snack with great potential to replace traditional ones.

Evaluation of Brazilian light ketchups II: quantitative descriptive and physicochemical analysis

Samples of ketchup available on the Brazilian market, one traditional (sweetened with sucrose) and three light versions (sweetened with aspartame, acesulfame-K and a blend of cyclamate, saccharin and stevia) were evaluated for their physicochemical characteristics and sensory profile (Quantitative Descriptive Analysis). Four main groups of attributes were generated: appearance, oral texture, aroma and flavor. The samples presented significant differences in all attributes, except for syneresis and overripe tomato flavor. The highest means for sweetener and bitter tastes and aftertastes were observed for the samples sweetened with acesulfame-K and the blend of sweeteners. Although different characteristics were observed among the products evaluated and, despite the differences in the formulations, the light ketchup sweetened with aspartame was the one that presented properties most similar to those of the traditional ketchup.

Pellets de trigo e soja produzidos por extrusão

A mistura de trigo e soja representa uma importante fonte calórico-protéica com proteínas de boa qualidade. Apesar disso, a utilização da soja como ingrediente tem sido limitada pelo seu sabor de feijão cru (beany flavor), o qual é melhorado pelo processo de extrusão. Foram estudados os efeitos de umidade da mistura, Temperatura de Barril (TB) e Velocidade de Rotação de Parafuso (VRP, Nº 5) do extrusor no Índice de Expansão (IE), no Índice de Solubilidade em Água (ISA) e nas características sensoriais de pellets produzidos com mistura de trigo e soja (90:10), objetivando a otimização deste processo para a obtenção de pellets fritos com melhores qualidades sensoriais. A farinha mista crua foi extrusada em 2 umidades (32 e 35%), 4 TB (60 a 90 °C) e 4 VRP (60 a 150 rpm), totalizando 32 tratamentos. O pellet frito, preparado com a farinha mista com 32% de umidade e extrusada em 60 rpm a 80 °C, apresentou o maior IE e as melhores qualidades sensoriais (aparência, sabor e textura), sendo preferido pela equipe de provadores não treinados, tanto com sabor de bacon como com sabor de queijo.