Optimization of Snow Drifting Mitigation and Control Methods for Iowa Conditions Part II, TR-626, 2015

Blowing and drifting of snow is a major concern for transportation efficiency and road safety in regions where their development is common. One common way to mitigate snow drift on roadways is to install plastic snow fences. Correct design of snow fences is critical for road safety and maintaining the roads open during winter in the US Midwest and other states affected by large snow events during the winter season and to maintain costs related to accumulation of snow on the roads and repair of roads to minimum levels. Of critical importance for road safety is the protection against snow drifting in regions with narrow rights of way, where standard fences cannot be deployed at the recommended distance from the road. Designing snow fences requires sound engineering judgment and a thorough evaluation of the potential for snow blowing and drifting at the construction site. The evaluation includes site-specific design parameters typically obtained with semi-empirical relations characterizing the local transport conditions. Among the critical parameters involved in fence design and assessment of their post-construction efficiency is the quantification of the snow accumulation at fence sites. The present study proposes a joint experimental and numerical approach to monitor snow deposits around snow fences, quantitatively estimate snow deposits in the field, asses the efficiency and improve the design of snow fences. Snow deposit profiles were mapped using GPS based real-time kinematic surveys (RTK) conducted at the monitored field site during and after snow storms. The monitored site allowed testing different snow fence designs under close to identical conditions over four winter seasons. The study also discusses the detailed monitoring system and analysis of weather forecast and meteorological conditions at the monitored sites. A main goal of the present study was to assess the performance of lightweight plastic snow fences with a lower porosity than the typical 50% porosity used in standard designs of such fences. The field data collected during the first winter was used to identify the best design for snow fences with a porosity of 50%. Flow fields obtained from numerical simulations showed that the fence design that worked the best during the first winter induced the formation of an elongated area of small velocity magnitude close to the ground. This information was used to identify other candidates for optimum design of fences with a lower porosity. Two of the designs with a fence porosity of 30% that were found to perform well based on results of numerical simulations were tested in the field during the second winter along with the best performing design for fences with a porosity of 50%. Field data showed that the length of the snow deposit away from the fence was reduced by about 30% for the two proposed lower-porosity (30%) fence designs compared to the best design identified for fences with a porosity of 50%. Moreover, one of the lower-porosity designs tested in the field showed no significant snow deposition within the bottom gap region beneath the fence. Thus, a major outcome of this study is to recommend using plastic snow fences with a porosity of 30%. It is expected that this lower-porosity design will continue to work well for even more severe snow events or for successive snow events occurring during the same winter. The approach advocated in the present study allowed making general recommendations for optimizing the design of lower-porosity plastic snow fences. This approach can be extended to improve the design of other types of snow fences. Some preliminary work for living snow fences is also discussed. Another major contribution of this study is to propose, develop protocols and test a novel technique based on close range photogrammetry (CRP) to quantify the snow deposits trapped snow fences. As image data can be acquired continuously, the time evolution of the volume of snow retained by a snow fence during a storm or during a whole winter season can, in principle, be obtained. Moreover, CRP is a non-intrusive method that eliminates the need to perform man-made measurements during the storms, which are difficult and sometimes dangerous to perform. Presently, there is lots of empiricism in the design of snow fences due to lack of data on fence storage capacity on how snow deposits change with the fence design and snow storm characteristics and in the estimation of the main parameters used by the state DOTs to design snow fences at a given site. The availability of such information from CRP measurements should provide critical data for the evaluation of the performance of a certain snow fence design that is tested by the IDOT. As part of the present study, the novel CRP method is tested at several sites. The present study also discusses some attempts and preliminary work to determine the snow relocation coefficient which is one of the main variables that has to be estimated by IDOT engineers when using the standard snow fence design software (Snow Drift Profiler, Tabler, 2006). Our analysis showed that standard empirical formulas did not produce reasonable values when applied at the Iowa test sites monitored as part of the present study and that simple methods to estimate this variable are not reliable. The present study makes recommendations for the development of a new methodology based on Large Scale Particle Image Velocimetry that can directly measure the snow drift fluxes and the amount of snow relocated by the fence.

Lake dwellers occupation gap in Lake Geneva (France-Switzerland) possibly explained by an earthquake-mass movement-tsunami event during Early Bronze Age

High-resolution seismic and sediment core data from the 'Grand Lac' basin of Lake Geneva reveal traces of repeated slope instabilities with one main slide-evolved mass-flow (minimum volume 0.13 km3) that originated from the northern lateral slope of the lake near the city of Lausanne. Radiocarbon dating of organic remains sampled from the top of the main deposit gives an age interval of 1865-1608 BC. This date coincides with the age interval for a mass movement event described in the 'Petit Lac' basin of Lake Geneva (1872-1622 BC). Because multiple mass movements took place at the same time in different parts of the lake, we consider the most likely trigger mechanism to be a strong earthquake (Mw 6) that occurred in the period between 1872 and 1608 BC. Based on numerical simulations, we show the major deposit near Lausanne would have generated a tsunami with local wave heights of up to 6 m. The combined effects of the earthquake and the following tsunami provide a possible explanation for a gap in lake dwellers occupation along the shores of Lake Geneva revealed by dendrochronological dating of two palafitte archaeological sites.

Mid- to Late Holocene shoreline reconstruction and human occupation in Ancient Eretria (South Central Euboea, Greece)

Few studies have aimed to reconstruct landscape change in the area of Eretria (South Central Euboea, Greece) during the last 6000 years. The aim of this paper is to partially fill in this gap by examining the interaction be- tween Mid- to Late Holocene shoreline evolution and human occupation, which is documented in the area from the Late Neolithic to the Late Roman period (with discontinuities). Evidence of shoreline displacements is derived from the study of five boreholes (maximum depth of 5.25 m below the surface) drilled in the lowlands of Eretria. Based on sedimentological analyses and micro/macrofaunal identifications, different facies have been identified in the cores and which reveal typical features of deltaic progradation with marine, lagoonal, fluvio- deltaic and fluvial environments. In addition, a chronostratigraphy has been obtained based on 20 AMS 14C radio- carbon dates performed on samples of plant remains and marine/lagoonal shells found in situ. The main sequences of landscape reconstruction in the plain of Eretria can be summarized as follows: a marine environ- ment predominated from ca. 4000 to 3200 cal. BC and a gradual transition to shallow marine conditions is ob- served ca. 3200-3000 cal. BC due to the general context of deltaic progradation west of the ancient city. Subsequently, from ca. 3000 to 2000 cal. BC, a lagoon occupied the area in the vicinity of the Temple of Apollo and the settlement's development was restricted to several fluvio-deltaic levees, thus severely limiting human activities in the plain. From ca. 2000 to 800 cal. BC, a phase of shallow marine presence prevailed and constrained settlement on higher ground, forcing abandonment of the major part of the plain. Finally, since the eighth century BC, the sea has regressed southward and created the modern landscape.

Notes sobre la presència d'algunes produccions locals i importades de vernís roig en la Tàrraco Julioclàudia

Amb aquest treball volem contribuir al coneixement de la dinàmica comercial de la Tàrraco del segle i dC. Es presenta una possible producció local documentada d’una manera abundant en el jaciment de la plaça de la Font de Tarragona. També presentem com a novetat un petit conjunt de ceràmiques procedents de la zona de Nàpols i Narbona. Per últim, destacar algunes imitacions de TSI d’origen indeterminat.

FY'15 Biodiesel Fuel Revolving Fund Expenditures Report

Pursuant to Iowa Code section 307.20, the biodiesel fuel revolving fund (Fund) was created and is to be used to purchase biodiesel fuel for use in the Department of Transportation’s vehicles. The act directed that the Fund receive money from the sale of EPAct credits banked by the DOT on the effective date of the act, monies appropriated by the General Assembly, and any other monies obtained or accepted by the DOT for deposit in the Fund. This report is of the expenditures made from the Fund during FY 2015.

Early Iron Age Pottery: A Quantitative Approach. Proceedings of the International Round Table organized by the Swiss School of Archaeology in Greece (Athens, Novembre 28-30, 2008).

Quantitative approaches in ceramology are gaining ground in excavation reports, archaeological publications and thematic studies. Hence, a wide variety of methods are being used depending on the researchers' theoretical premise, the type of material which is examined, the context of discovery and the questions that are addressed. The round table that took place in Athens on November 2008 was intended to offer the participants the opportunity to present a selection of case studies on the basis of which methodological approaches were discussed. The aim was to define a set of guidelines for quantification that would prove to be of use to all researchers. Contents: 1) Introduction (Samuel Verdan); 2) Isthmia and beyond. How can quantification help the analysis of EIA sanctuary deposits? (Catherine Morgan); 3) Approaching aspects of cult practice and ethnicity in Early Iron Age Ephesos using quantitative analysis of a Protogeometric deposit from the Artemision (Michael Kerschner); 4) Development of a ceramic cultic assemblage: Analyzing pottery from Late Helladic IIIC through Late Geometric Kalapodi (Ivonne Kaiser, Laura-Concetta Rizzotto, Sara Strack); 5) 'Erfahrungsbericht' of application of different quantitative methods at Kalapodi (Sara Strack); 6) The Early Iron Age sanctuary at Olympia: counting sherds from the Pelopion excavations (1987-1996) (Birgitta Eder); 7) L'aire du pilier des Rhodiens à Delphes: Essai de quantification du mobilier (Jean-Marc Luce); 8) A new approach in ceramic statistical analyses: Pit 13 on Xeropolis at Lefkandi (David A. Mitchell, Irene S. Lemos); 9) Households and workshops at Early Iron Age Oropos: A quantitative approach of the fine, wheel-made pottery (Vicky Vlachou); 10) Counting sherds at Sindos: Pottery consumption and construction of identities in the Iron Age (Stefanos Gimatzidis); 11) Analyse quantitative du mobilier céramique des fouilles de Xombourgo à Ténos et le cas des supports de caisson (Jean-Sébastien Gros); 12) Defining a typology of pottery from Gortyn: The material from a pottery workshop pit, (Emanuela Santaniello); 13) Quantification of ceramics from Early Iron Age tombs (Antonis Kotsonas); 14) Quantitative analysis of the pottery from the Early Iron Age necropolis of Tsikalario on Naxos (Xenia Charalambidou); 15) Finding the Early Iron Age in field survey: Two case studies from Boeotia and Magnesia (Vladimir Stissi); 16) Pottery quantification: Some guidelines (Samuel Verdan).

Mineral zoning and geochemistry of epithermal polymetallic Zn-Pb-Ag-Cu-Bi mineralization at Cerro de Pasco, Peru

The large Cerro de Pasco Cordilleran base metal deposit in central Peru is located on the eastern margin of a middle Miocene diatreme-dome complex and comprises two mineralization stages. The first stage consists of a large pyrite-quartz body replacing Lower Mesozoic Pucara carbonate rocks and, to a lesser extent, diatreme breccia. This body is composed of pyrite with pyrrhotite inclusions, quartz, and black and red chalcedony (containing hypogene hematite). At the contact with the pyrite-quartz body, the diatreme breccia is altered to pyrite-quartz-sericite-pyrite. This body was, in part, replaced by pipelike pyrrhotite bodies zoned outward to carbonate-replacement Zn-Pb ores hearing Fe-rich sphalerite (up to 24 mol % Fes). The second mineralization stage is partly superimposed on the first and consists of zoned east-west-trending Cu-Ag-(Au-Zn-Pb) enargite-pyrite veins hosted in the diatreme breccia in the western part of the deposit and well-zoned Zn-Pb-(Bi-Ag-Cu) carbonate-replacement orebodies; in both cases, sphalerite is Fe poor and the inner parts of the orebodies show typically advanced argillic alteration assemblages, including aluminum phosphate Sulfate (APS) minerals. The zoned enargite-pyrite veins display mineral zoning, from a core of enargite-pyrite +/- alunite with traces of Au, through an intermediate zone of tennantite, chalcopyrite, and Bi minerals to a poorly developed Outer zone hearing sphalerite-galena +/- kaolinite. The carbonate-hosted replacement ores are controlled along N 35 degrees E, N 90 degrees E, N 120 degrees E, and N 170 degrees E faults. They form well-zoned upward-flaring pipelike orebodies with a core of famatinite-pyrite and alunite, an intermediate zone with tetrahedrite-pyrite, chalcopyrite, matildite, cuprobismutite, emplectite, and other Bi minerals accompanied by APS minerals, kaolinite, and dickite, and an outer zone composed of Fe-poor sphalerite (in the range of 0.05-3.5 mol % Fes) and galena. The outermost zone consists of hematite, magnetite, and Fe-Mn-Zn-Ca-Mg carbonates. Most of the second-stage carbonate-replacement orebodies plunge between 25 degrees and 60 degrees to the west, suggesting that the hydrothermal fluids ascended from deeper levels and that no lateral feeding from the veins to the carbonate-replacement orebodies took place. In the Venencocha and Santa Rosa areas, located 2.5 km northwest of the Cerro de Pasco open pit and in the southern part of the deposit, respectively, advanced argillic altered dacitic domes and oxidized veins with advanced argillic alteration halos occur. The latter veins are possibly the oxidized equivalent of the second-stage enargite-pyrite veins located in the western part of the deposit. The alteration assemblage quartz-muscovite-pyrite associated with the pyrite-quartz body suggests that the first stage precipitated at slightly, acidic fin. The sulfide mineral assemblages define an evolutionary path close to the pyrite-pyrrhotite boundary and are characteristic of low-sulfidation states; they suggest that the oxidizing slightly acidic hydrothermal fluid was buffered by phyllite, shale, and carbonate host rock. However, the presence in the pyrite-quartz body of hematite within quartz suggests that, locally, the fluids were less buffered by the host rock. The mineral assemblages of the second mineralization stage are characteristic of high- to intermediate-sulfidation states. High-sulfidation states and oxidizing conditions were achieved and maintained in the cores of the second-stage orebodies, even in those replacing carbonate rocks. The observation that, in places, second-stage mineral assemblages are found in the inner and outer zones is explained in terms of the hydrothermal fluid advancing and waning. Microthermometric data from fluid inclusions in quartz indicate that the different ores of the first mineralization stage formed at similar temperatures and moderate salinities (200 degrees-275 degrees C and 0.2-6.8 wt % NaCl equiv in the pyrite-quartz body; 192 degrees-250 degrees C and 1.1-4.3 wt % NaCl equiv in the pyrrhotite bodies; and 183 degrees-212 degrees C and 3.2-4.0 wt % NaCl equiv in the Zn-Pb ores). These values are similar to those obtained for fluid inclusions in quartz and sphalerite from the second-stage ores (187 degrees-293 degrees C and 0.2-5.2 wt % NaCl equiv in the enargite-pyrite veins: 178 degrees-265 degrees C and 0.2-7.5 wt % NaCl equiv in quartz of carbonate-replacement orebodies; 168 degrees-999 degrees C and 3-11.8 wt % NaCl equiv in sphalerite of carbonate-replacement orebodies; and 245 degrees-261 degrees C and 3.2-7.7 wt % NaCl equiv in quartz from Venencocha). Oxygen and hydrogen isotope compositions oil kaolinite from carbonate-replacement orebodies (delta(18)O = 5.3-11.5%o, delta D = -82 to -114%o) and on alunite from the Venencocha and Santa Rosa areas (delta(18)O = 1.9-6.9%o, delta D = -56 to -73%o). Oxygen isotope compositions of quartz from the first and second stages have 6180 values from 9.1 to 1.7.8 per mil. Calculated fluids in equilibrium with kaolinite have delta(18)O values of 2.0 to 8.2 and delta D values of -69 to -97 per mil; values in equilibrium with alunite are -1.4 to -6.4 and -62 to -79 per mil. Sulfur isotope compositions of sulfides from both stages have a narrow range of delta(34)S values, between -3.7 and +4.2 per mil; values for sulfates from the second stage are between 4.2 and 31.2 per mil. These results define two mixing trends for the ore-forming fluids. The first trend reflects mixing between a moderately saline (similar to 10 wt % NaCl equiv) magmatic end member that had degassed (as indicated by the low delta D values) and meteoric water. The second mixing indicates condensation of magmatic vapor with HCl and SO(2) into meteoric water, which formed alunite. The hydrothermal system at Cerro de Pasco was emplaced at a shallow depth (similar to 500 m) in the epithermal and upper part of a porphyry environment. The similar temperatures and salinities obtained for the first stage and second stages, together with the stable isotope data, indicate that both stages are linked and represent successive stages of epithermal polymetallic mineralization in the upper part of a porphyry system.

Stable isotope (C, O, S) systematics of the mercury mineralization at Idrija, Slovenia: constraints on fluid source and alteration processes

The world-class Idrija mercury deposit (western Slovenia) is hosted by highly deformed Permocarboniferous to Middle Triassic sedimentary rocks within a complex tectonic structure at the transition between the External Dinarides and the Southern Alps. Concordant and discordant mineralization formed concomitant with Middle Triassic bimodal volcanism in an aborted rift. A multiple isotopic (C, O, S) investigation of host rocks and ore minerals was performed to put constraints on the source and composition of the fluid, and the hydrothermal alteration. The distributions of the delta(13)C and delta(18)O values of host and gangue carbonates are indicative of a fracture-controlled hydrothermal system, with locally high fluid-rock ratios. Quantitative modeling of the delta(13)C and delta(18)O covariation for host carbonates during temperature dependent fluid-rock interaction, and concomitant precipitation of void-filling dolomites points to a slightly acidic hydrothermal fluid (delta(13)Capproximate to-4parts per thousand and delta(18)Oapproximate to+10parts per thousand), which most likely evolved during isotopic exchange with carbonates under low fluid/rock ratios. The delta(34)S values of hydrothermal and sedimentary sulfur minerals were used to re-evaluate the previously proposed magmatic and evaporitic sulfur sources for the mineralization, and to assess the importance of other possible sulfur sources such as the contemporaneous seawater sulfate, sedimentary pyrite, and organic sulfur compounds. The delta(34)S values of the sulfides show a large variation at deposit down to hand-specimen scale. They range for cinnabar and pyrite from -19.1 to +22.8parts per thousand, and from -22.4 to +59.6parts per thousand, respectively, suggesting mixing of sulfur from different sources. The peak of delta(34)S values of cinnabar and pyrite close to 0parts per thousand is compatible with ore sulfur derived dominantly from a magmatic fluid and/or from hydrothermal leaching of basement rocks. The similar stratigraphic trends of the delta(34)S values of both cinnabar and pyrite suggest a minor contribution of sedimentary sulfur (pyrite and organic sulfur) to the ore formation. Some of the positive delta(34)S values are probably derived from thermochemical reduction of evaporitic and contemporaneous seawater sulfates.

Apparent stable-isotope heterogeneities in gangue carbonates of the Mississippi Valley-type Zn-Pb deposits of San-Vicente, Central Peru

The aim of the present communication is to emphasize that some variations of the measured delta(13)C and delta(18)O values are apparent, and due to analytical interferences caused by the presence of sulfur and organosulfur compounds in the analyzed carbonates. This is particularly relevant for isotopic studies on carbonate-hosted mineral deposits, where the nearly ubiquitous association of the host carbonates with organic matter and sulfides can certainly affect the metallogenetic interpretations. In this work two methods were used to overcome the disturbing effects of sulfides and organic matter: (1) sample pretreatment following the method proposed by Charef and Sheppard (1984), combining the oxidation of organic matter with sodium hypochlorite and trapping of the sulfur species with silver phosphate; and (2) laser-based microprobe extraction. Apparent isotopic variations in sparry dolomite from a single hand sample of zebra ore from the MVT Zn-Pb deposit, San Vicente, central Peru, are as large as 6 parts per thousand delta(13)C and 4 parts per thousand delta(18)O. These variations are reduced to several tenths of a per mil when the samples are pretreated. A careful examination of the effects of treatment with NaOCl and/or Ag3PO4 in relation to the concentration of sulfide inclusions indicates that the main disturbing effects for delta(13)C values are the presence of sulfur species and organic matter, whereas the delta(18)O values are mainly affected by the presence of sulfides. Fine- and medium-grained replacement carbonates from MVT and other sediment-hosted base metal deposits are potentially the most affected during isotope analysis, due to the common presence of organic matter and sulfides. Using in situ laser microprobe techniques, it is possible to determine isotopic variations at a sub-millimeter scale. Our results show that laser extraction analysis allows a more precise sampling of the carbonate minerals, and minimizes contamination of the sample with sulfides and to some extent with intergrown organic matter. However, there is an isotopic shift associated with the laser extraction technique, of the order of 0.5-1 parts per thousand for delta(13)C and delta(18)O values.

6.2

Airborne particles can come from a variety of sources and contain variable chemical constituents. Some particles are formed by natural processes, such as volcanoes, erosion, sea spray, and forest fires, while other are formed by anthropogenic processes, such as industrial- and motor vehicle-related combustion, road-related wear, and mining. In general, larger particles (those greater than 2.5 μm) are formed by mechanical processes, while those less than 2.5 μm are formed by combustion processes. The chemical composition of particles is highly influenced by the source: for combustion-related particles, factors such as temperature of combustion, fuel type, and presence of oxygen or other gases can also have a large impact on PM composition. These differences can often be observed at a regional level, such as the greater sulphate-composition of PM in regions that burn coal for electricity production (which contains sulphur) versus regions that do not. Most countries maintain air monitoring networks, and studies based on the resulting data are the most common basis for epidemiology studies on the health effects of PM. Data from these monitoring stations can be used to evaluate the relationship between community-level exposure to ambient particles and health outcomes (i.e., morbidity or mortality from various causes). Respiratory and cardiovascular outcomes are the most commonly assessed, although studies have also considered other related specific outcomes such as diabetes and congenital heart disease. The data on particle characteristics is usually not very detailed and most often includes some combination of PM2.5, PM10, sulphate, and NO2. Other descriptors that are less commonly found include particle number (ultrafine particles), metal components of PM, local traffic intensity, and EC/OC. Measures of association are usually reported per 10 μg/m3 or interquartile range increase in pollutant concentration. As the exposure data are taken from regional monitoring stations, the measurements are not representative of an individual's exposure. Particle size is an important descriptor for understanding where in the human respiratory system the particles will deposit: as a general rule, smaller particles penetrate to deeper regions of the lungs. Initial studies on the health effects of particulate matter focused on mass of the particles, including either all particles (often termed total suspended particulate or TSP) or PM10 (all particles with an aerodynamic diameter less than 10 μm). More recently, studies have considered both PM10 and PM2.5, with the latter corresponding more directly to combustion-related processes. UFPs are a dominant source of particles in terms of PNC, yet are negligible in terms of mass. Very few epidemiology studies have measured the effect of UFPs on health; however, the numbers of studies on this topic are increasing. In addition to size, chemical composition is of importance when understanding the toxicity of particles. Some studies consider the composition of particles in addition to mass; however this is not common, in part due the cost and labour involved in such analyses.

Glial hyaluronate-binding protein expression in aggregating brain cell cultures.

We analyzed the expression of glial hyaluronate-binding protein (GHAP), an integral component of the extracellular matrix, in aggregating brain cell cultures of fetal rat telencephalon using immunofluorescence. GHAP immunoreactivity appeared after 1 week in culture, simultaneous with the first deposits of myelin basic protein, and showed a development-dependent increase. Comparison of glia-enriched and neuron-enriched cultures showed that only glial cells express GHAP. Three peptide growth factors, epidermal growth factor, fibroblast growth factor and platelet-derived growth factor, which are known to stimulate the differentiation of glial cells, modulated the deposit of GHAP immunoreactivity. The 3-dimensional structure of aggregate cultures promoted GHAP deposition, suggesting that cell-cell interactions are required for extracellular matrix formation. Furthermore GHAP production seemed to depend on the developmental stage of the glial cells.

Determining, Balancing and Controlling of Pitch and White Pitch at Stora Enso Kabel Production Line 4

Työn ensimmäisenä tarkoituksena oli kartoittaa kiinteä-neste ja neste-neste uuttomenetelmillä pihkan ja valkopihkan määrä Stora Enso Kabelin tuotantolinja 4:llä. Työn kannalta oli myöstärkeää saada selvyys saostumien koostumuksesta. Lopullinen päämäärä oli automatisoida fiksatiivin annostelu uuden, jatkuvatoimisen märänpäänanalysaattorin avulla. Mäntyosuuden kasvattaminen hiokemassassa lisää hydrofobisten partikkeleiden lukumäärää, minkä uskotaan lisäävän saostumariskiä. Työtä varten kehitetty neste-neste uuttomenetelmä, jota ei ole liiemmin paperiteollisuudessa käytetty, voi olla hyvä menetelmä lipofiilisten komponenttien määrän arviointiin tietyssä määrässä massa- tai prosessivesinäytettä. Virtaussytometri-menetelmän avulla tutkittiin pihka- tai valkopihkapartikkeleiden määrää ja kokojakaumaa eri prosessinäytteissä. Virtaussytometri-menetelmällä mitattujen valkopihkapartikkeleiden lukumäärän ja päällystetyn hylyn saostimen suodoksen sameuden välille löytyiselvä korrelaatio. Fiksatiivimäärän vaikutusta päällystetyn hylyn saostimen suodoksen sameuteen tutkittiin koeajojaksolla, jossa fiksatiivin annostelua säädettiin käsin. Käytetyt annosmäärät eivät riittäneet sameuden pitämiseen tasaisena matalalla tasolla.

Elektroniikka - ja sähköromun (SER) kierrätys

Tässä työssä pyrin tarkastelemaan sähkö- ja elektroniikkaromun kierrätystä erityisesti EU - direktiivin mukaisen tuottajavastuun näkökulmasta. Käytettyjen sähkö- ja elektroniikkalaitteiden vuori kasvaa koko ajan kaikkialla Euroopassa. Euroopan parlamentti hyväksyi joulukuussa 2002 kaksi uutta direktiiviä, joilla pyritään lieventämään sähköromuongelmaa. Parlamentin vaatimusten ansiosta unionin jäsenvaltioiden on taattava, että laitteiden valmistajat maksavat omista tuotteistaan syntyvän sähkö- ja elektroniikkalaitejätteen keräys-, käsittely- ja kierrätyskustannukset. Tämä merkitsee esimerkiksi sitä, että kuluttajat voivat viedä vanhat sähkölaitteensa asuinpaikkansa läheisyydessä sijaitseviin maksuttomiin keräyspisteisiin. Myös kuluttajien on otettava vastuu hankkimistaan tuotteista: sähkö- ja elektroniikkalaitejätteen hävittäminen tavallisen kotitalousjätteen seassa tullaan kieltämään.

A case of acute retinal pigment epithelitis: spectral domain optical coherence tomography time course and physiopathologic hypothesis.

PURPOSE: To report the time course of retinal morphologic changes in a patient with acute retinal pigment epithelitis (ARPE) using spectral domain optical coherence tomography (SD-OCT). METHODS: A 30-year old man was referred for blurred vision of his right eye after five days that appeared suddenly 15 days after recovery from a flu-like syndrome. SD-OCT was performed immediately, followed by fluorescein and infracyanine angiography at eight days and then at three weeks. RESULTS: At presentation, a bubble of sub-macular deposit was observed on the right macula with central golden micronodules in a honeycomb pattern. SD-OCT showed an "anterior dislocation" of all the retinal layers up to the inner/outer segment (IS/OS) line and irregular deposits at the OS level together with thickening of the retinal pigment epithelial (RPE) layer. As visual acuity increased, eight days later, the OCT showed reduction of the sub-retinal deposits and an abnormal hyperflectivity of the sub-retinal and RPE layers was observed. The patient showed a positive serology for picornavirus. DISCUSSION: The acute SD-OCT sections of this patient with ARPE were compared with histological sections of a 35 day old Royal College of Surgeons rat. Similar findings could be observed, with preservation of the IS/OS line and accumulation of debris at the OS level, suggesting that ARPE symptoms could result from a transient phagocytic dysfunction of the RPE at the fovea, inducing reversible accumulation of undigested OS. Picornaviruses comprising enterovirus and coxsachievirus described as being associated with acute chorioretinitis. In this case, it was responsible for ARPE. CONCLUSION: We hypothesize that ARPE syndrome results from a transient dysfunction of RPE, which can occur as a post viral reaction.

Événements et déformations tardi-métamorphiques dans le segment Ossola-Ticino (Val Vigezzo-Centovalli, Italie-Suisse)

RESUME: Une zone tectonique large et complexe, connue sous le nom de ligne des Centovalli, traverse le secteur des Alpes Centrales compris entre Domodossola et Locarno. Cette région, formée par le Val Vigezzo et la vallée des Centovalli, constitue la terminaison méridionale du dôme Lepontin et représente une portion de la zone des racines des nappes alpines. Elle fait partie d’une grande et complexe zone de cisaillement, en partie associée à des phénomènes hydrothermaux d’âge alpin (<20 Ma), qui comprend le système tectonique Insubrien et celui du Simplon. Le Val Vigezzo et les Centovalli constituent un vrai carrefour entre les principaux accidents tectoniques des Alpes ainsi qu'une zone de juxtaposition du socle Sudalpin avec la zone des racines de l’Austroalpin et du Pennique. Les phases de déformation et les structures géologiques qui peuvent être étudiées s'étalent sur une période comprise entre environ 35 Ma et l'actuel. L’étude détaillée de terrain a mis en évidence la présence de nombreuses roches et structures de déformation de type ductile et cassant tels que des mylonites, des cataclasites, des pseudotachylites, des kakirites, des failles minéralisées, des gouges de faille et des plis. Sur le terrain on a pu distinguer au moins quatre générations de plis liés aux différentes phases de déformation. Le nombre et la complexité de ces structures indiquent une histoire très compliquée, selon plusieurs étapes distinctes, parfois liées, voire même superposées. Une partie de ces structures de déformation affectent aussi les dépôts sédimentaires d’âge quaternaire, notamment des limons et des sables lacustres. Ces sédiments constituent les restes d'un bassin lacustre attribué à l'époque interglaciaire Riss/Würm (éemien, 67.000-120.000 ans) et ils affleurent dans la partie centrale de la zone étudiée, à l'Est de la plaine de Santa Maria Maggiore. Ces sédiments montrent en leur sein toute une série de structures de déformation tels que des plans de faille inverses, des structures conjuguées de raccourcissement et des véritables plis. Ces failles et ces plis représenteraient les évidences de surface d’une déformation probablement active en époque quaternaire. Une autre formation rocheuse a retenu tout notre attention; il s'agit d'un corps de brèches péridotitiques monogéniques qui affleure en discontinuité le long du versant méridional et le long du fond de la vallée Vigezzo sur environ 20 km. Ces brèches se posent indifféremment sur le socle (unités Finero, Orselina) ou sur les sédiments lacustres. Elles sont traversées par des plans de failles qui développent des véritables stries de faille et des gouges de faille; l’orientation de ces plans est la même que celle affectant les failles à gouges du socle. La genèse de cette brèche est liée à l'altération et au modelage glacier (rock-glaciers) d'une brèche tectonique originelle qui borde la partie externe du Corps de Finero. Les structures de déformation de cette brèche, pareillement à celles des sédiments lacustres, ont été considérées comme les évidences de surface d'une tectonique quaternaire active dans la région. La dernière phase de déformation cassante qui affecte cette région peut donc être considérée comme active en époque quaternaire. Une vue d’ensemble de la région étudiée nous permet de reconnaître à l’échelle régionale une zone de cisaillement complexe orientée E-W, parallèlement à l’axe de la vallée Centovalli-Val Vigezzo. Les données de terrain, indiquent que cette zone de cisaillement débute sous conditions ductiles et évolue en plusieurs étapes jusqu’à des conditions de failles cassantes de surface. La reconstruction de l'évolution géodynamique de la région a permis de définir trois étapes distinctes qui marquent le passage, de ce secteur de socle cristallin, de conditions P-T profondes à des conditions de surface. Dans ce contexte, on a reconnu trois phases principales de déformation à l’échelle régionale qui caractérisent ces trois étapes. La phase la plus ancienne est constituée par des mylonites en faciès amphibolite, associées à des mouvements de cisaillement dextre, qui sont ensuite remplacés par des mylonites en faciès schistes verts et des plis rétrovergentes liés au rétrocharriage des nappes alpines. Une deuxième étape est identifiée par le développement d’une phase hydrothermale liée à un système de failles extensives et décrochantes dextres à direction principale E-W, NE-SW et NW-SE. Leur caractérisation minéralogique a permis la mise en évidence des phases cristallines de néoformation liées à cet événement constituées par : K-feldspath (microcline), chlorites (Fe+Mg), épidotes, prehnite, zéolites (laumontite), sphène, calcite. Dans ce contexte, pour obtenir une meilleure caractérisation de cet événement hydrothermal on a utilisé des géothermomètres sur chlorites, sensible aussi à la pression et a la a(H2O), qui ont donné des valeurs descendantes comprises entre 450-200°C. Les derniers mouvements sont mis en évidence par le développement d’une série de plans majeurs de failles à gouge, qui forment une structure en sigmoïdes d’épaisseur kilométrique reconnaissable à l’échelle de la vallée et caractérisée par des mouvements transpressifs avec une composante décrochante dextre toujours importante. Cette phase de déformation forme un système conjugué de failles avec direction moyenne E-W qui coupent la zone des racines des nappes alpines, la zone du Canavese et le corps ultramafique de Finero. Ce système se déroule de manière subparallèle à l'axe de la vallée le long de plusieurs dizaines de kilomètres. Une analyse complète et détaillée des gouges de faille par XRD a montré que la fraction argileuse (<2 µm) de ces gouges contient une partie de néoformation très importante constituée par, des illites, des chlorites et des interstratifiés de type illite/smectite ou chlorite/smectite. Des datations avec méthode K-Ar sur ces illites ont donné des valeurs comprises entre 12 et 4 Ma qui représentent l'âge de cette dernière déformation cassante. L'application de la méthode de la cristallinité de l'illite (C.I.) a permis d'évaluer les conditions thermiques qui caractérisent le déroulement de cette dernière phase tectonique qui se produit sous conditions de température caractéristiques de l'anchizone et de la diagenèse. L'ensemble des structures de déformation qu'on vient de décrire s'insère parfaitement dans le contexte de convergence oblique entre la plaque adriatique et celle européenne qui à produit l'orogène alpin. On peut considérer les structures tectoniques du Val Vigezzo-Centovalli comme l'expression d'une zone majeure de cisaillement "Simplo-Insubrienne". L'empilement structural et les structures tectoniques affleurantes dans la région sont le résultat de l'interaction entre un régime tectonique transpressif et un régime transtensif. Ces deux champs de tension sont antagonistes entre eux mais sont reliés, de toute façon, à une seule phase décrochante dextre principale, due à une convergence oblique entre deux plaques. À l'échelle de l'évolution géodynamique on peut distinguer différentes étapes au cours desquelles les structures de ces deux régimes tectoniques interagissent en manière différente. En accord avec les données géophysiques et les reconstructions paléodynamiques prises dans la littérature on considère que la ligne Rhône-Simplon-Centovalli représente l'évidence de surface de la suture majeure profonde entre la plaque Adriatique et celle Européenne. Les vitesses de soulèvement qui ont été calculées dans cette étude pour cette région des Alpes donnent une valeur moyenne de 0.8 mm/a qui est tout à fait comparable avec les données proposées par la littérature sur cette zone. La zone Val Vigezzo-Centovalli peut être donc considérée comme un carrefour géologique où se croisent différentes phases tectoniques qui représentent les évidences de surface d'une suture profonde majeure entre deux plaques dans un contexte de collision continentale. ABSTRACT: A wide and complex tectonic zone known as Centovalli line, crosses the Central Alps sector between Domodossola and Locarno. This area, formed by the Vigezzo Valley and Centovalli valley, constitutes the southernmost termination of the Lepontin dome and represents a portion of the alpine nappes root zone. It belongs to a large and complex shear-zone, partly associated with hydrothermal phenomena of alpine age (<20 My), which includes the Insubric Line and the Simplon fault zone. Vigezzo Valley and Centovalli constitute a real crossroads between the mains alpines tectonics lines as well as a zone of juxtaposition of the Southalpine basement with the Austroalpin and Pennique root zone. The deformation phases and the geological structures that can be studied between approximately 35 My and the present. The detailed field study showed the presence of many brittle and ductile deformation structures and fault rocks such as mylonites, cataclasites, pseudotachylites, kakirites, mineralized faults, fault gouges and folds. In the field we could distinguish at least four folds generations related to the various deformation phases. The number and the complexity of these structures indicate a very complicated history, comprising several different stages, that sometimes are related and even superimposed. Part of these deformation structures affect also the sedimentary deposits of quaternary age, in particular the silts and sands lake deposit. These sediments constitute the remainders of a lake basin ascribed to the interglacial Riss/Würm (Eemien, 67.000-120.000 years) and outcroping in the central part of the studied area, in the Eastern part of Santa Maria Maggiore plain. These sediments show a whole series of deformation structures such as inverse fault planes, combined shortening structures and true folds. These faults and folds would represent the surface evidence of a probably active tectonic deformation in quaternary time. Another rock formation attracted all our attention. It is a body of monogenic peridotite breccia which outcrops in discontinuity along the southernmost slope and the bottom of the Vigezzo valley on approximately 20 km. This breccia lies indifferently on the basement (Finero and Orselina units) or on the lake sediments. They are crossed by fault planes which developed slikenside and fault gouges whose orientation is the same of the faults gouges in the alpine basement. This breccia results from the weathering and the surface modelling of an original tectonic breccia which borders the external part of Finero peridotite body. This breccia deformation structures, like those of the lake sediments, were regarded as the surface interaction of active quaternary tectonics in the area. So the last brittle deformation phases which affects this area seems to be actives in quaternary time. Theoverall picture of the studied area on a regional scale enables us to point out a complex shear-zone directed E-W, parallel to the axis of the Centovalli and Vigezzo Valley. The field analysis indicates that this shear-zone began under ductile conditions and evolved in several stages to brittle faulting under surface conditions. The analysis of the geodynamic evolution of the area allows to define three different stages which mark the transition of this alpine basement root zone, from deep P-T conditions to P-T surface conditions. In this context on regional scale three principal deformation phases, which characterize these three stages can be distinguished. The oldest phase consisted of the amphibolitie facies mylonites, associated to dextral strikeslip movements. They are then replaced by green-schists facies mylonites and backfolds related to the backthrusting of the alpines nappes. A second episode is caracterized by the development of an hydrothermal phase bound to an extensive fault and dextral strike-slip fault system, with E-W, NW-SE and SE-NW principal directionsThe principal neoformed mineral phases related to this event are: K-feldspar (microcline), chlorites (Fe+Mg), epidotes prehnite, zéolites (laumontite), sphene and calcite. In this context, to obtain a better characterization of this hydrothermal event, we have used an chlorite geothermometer, sensitive also to the pressure and has the a(H2O), which gave downward values ranging between 450-200°C. The last movements are caracterized by the development of important gouge fault plans, which form a sigmoid structure of kilometric thickness which is recognizable at the valley scale, and is characterized by transpressive movements always with a significant dextral strike-slip component. This deformation phase forms a combined faults system with an average E-W direction, which cuts trough the alpine root zone, the Canavese zone and the Finero ultramafic body. This fault system takes place subparallel to the axis of the valley over several tens of kilometers. A complete and detailed XRD analysis of the gouges fault showed that the clay fraction (<2µm) contains a very significant neo-formation of illite, chlorites and mixed layered clays such as illite/smectite or chlorite/smectite. The K-Ar datings of the illite fraction <2µm gave values ranging between 12 and 4 My and the illite fraction <0.2µm gave more recents values until to 2,4-0 My.This values represent the age of this last brittle deformation. The application of the illite crystallinity method (C.I.) allowed evaluating the thermal conditions which characterize this tectonic phase that occured under temperature conditions of the anchizone and diagenesis. The whole set of deformation structures which we just described, perfectly fit the context of oblique convergence between the Adriatic and the European plate that produced the alpine orogen. We can regard the Vigezzo valley and Centovalli tectonic structures as the expression of a major "Simplo-Insubric" shear-zone. Structural stacking and tectonic structures that outcrop in the studied area, are the result of the interaction between a transpressive and a transtensve tectonic phases. These two tension fields are antagonistic but they are also connected, in any event, with only one principal dextral strike-slip movement, caused by an oblique convergence between two plates. On the geodynamic evolution scale we can distinguish various stages during which these two tectonic structures fields interact in various ways. In agreement with the geophysical data and the paleodynamic recostructions taken in the literature we considers that the Rhone-Simplon-Centovalli line are the surface feature of the major collision between the Adriatique and the European plate at depth. The uplift speeds we calculated in this study for this Alpine area give an average value of 0.8 mm/a, which is in good agreement with the data suggested by the literature on this zone. TheVigezzo Valley and Centovalli zone can therefore be regarded as a geological crossroad where various tectonic phases are superimposed. They represent the evidences of a major and deeper suture between two plates in a continental collision context.