Modelagem e simulação de ciclos a gás com resfriamento de ar na entrada

The optimization of energy generation systems has become a key issue for technological and social development, mainly in developing countries, where the electricity consumption rises sharply. Gas turbine cycle is an electricity generating system, which studies have demonstrated that inlet air cooling increases net power and thermal efficiency. Thus, this study intends to quantify these parameters for environments with different ambient temperature and relative humidity. Two types of air cooling were used: evaporative and absorption systems. The configuration parameters only with the gas turbine cycle were compared to those whose configuration allowed cooling. First, it was analyzed only evaporative cooling. Next, the absorption system was used for analysis. The last configuration mixed these two methods, dividing equally its flow. The results showed that thermal efficiency and net power increase in any case of cooling, with absorption system more advantageous in terms of generated energy, where an increase between 1 and 2 MW was observed, depending on the ambient conditions . When the two methods were working together at low relative humidity, it showed a thermal efficiency increase compared to absorption system, up to 2.4%. Evaporative cooling was less effective, but it is a good and cheap possibility to increase the cycle parameters at high temperature and low relative humidity

Microclimate under different shading screens in greenhouses cultivated with bromeliads

This study had as its objective the evaluation of the influence of shading screens of different colors on the different microclimate variables in a greenhouse covered with transparent low-density polyethylene (LDPE). The experiment was conducted with five treatments: thermo-reflective screen (T1); a control - without screen (T2); red screen (T3); blue screen (T4); and black screen (T5), all of them with 70% of shading. An automatic micrometeorological station was installed in each treatment, measuring air temperature (T), relative humidity (RH), incoming solar radiation (Rg), photosynthetically active radiation (PAR) and net radiation (Rn) continuously. The control (T2) and red screen (T3) treatments promoted the highest solar radiation transmissivity, respectively 56.3 and 27%. The black screen (T5) had the lowest solar radiation transmissivity (10.4%). For PAR and Rn the same tendency was observed. The highest temperature was observed under blue screen (T4) treatment, which was 1.3 °C higher than external condition. Blue screen (T4) treatment also presented the highest relative humidity difference between inside and outside conditions.

Hydration of the Sulfuric Acid−Methylamine Complex and Implications for Aerosol Formation

The binary H2SO4−H2O nucleation is one of the most important pathways by which aerosols form in the atmosphere, and the presence of ternary species like amines increases aerosol formation rates. In this study, we focus on the hydration of a ternary system of sulfuric acid (H2SO4), methylamine (NH2CH3), and up to six waters to evaluate its implications for aerosol formation. By combining molecular dynamics (MD) sampling with high-level ab initio calculations, we determine the thermodynamics of forming H2SO4(NH2CH3)(H2O)n, where n = 0−6. Because it is a strong acid−base system, H2SO4−NH2CH3 quickly forms a tightly bound HSO4−−NH3CH3+ complex that condenses water more readily than H2SO4 alone. The electronic binding energy of H2SO4−NH2CH3 is −21.8 kcal mol−1 compared with −16.8 kcal mol−1 for H2SO4−NH3 and −12.8 kcal mol−1 for H2SO4−H2O. Adding one to two water molecules to the H2SO4−NH2CH3 complex is more favorable than adding to H2SO4 alone, yet there is no systematic difference for n ≥ 3. However, the average number of water molecules around H2SO4−NH2CH3 is consistently higher than that of H2SO4, and it is fairly independent of temperature and relative humidity.

Hydration of the Sulfuric Acid-Methylamine Complex and Implications for Aerosol Formation

The binary H2SO4-H2O nucleation is one of the most important pathways by which aerosols form in the atmosphere, and the presence of ternary species like amines increases aerosol formation rates. In this study, we focus on the hydration of a ternary system of sulfuric acid (H2SO4), methylamine (NH2CH3), and up to six waters to evaluate its implications for aerosol formation. By combining molecular dynamics (MD) sampling with high-level ab initio calculations, we determine the thermodynamics of forming H2SO4(NH2CH3)(H2O)n, where n = 0-6. Because it is a strong acid-base system, H2SO4-NH2CH3 quickly forms a tightly bound HSO4(-)-NH3CH3(+) complex that condenses water more readily than H2SO4 alone. The electronic binding energy of H2SO4-NH2CH3 is -21.8 kcal mol(-1) compared with -16.8 kcal mol(-1) for H2SO4-NH3 and -12.8 kcal mol(-1) for H2SO4-H2O. Adding one to two water molecules to the H2SO4-NH2CH3 complex is more favorable than adding to H2SO4 alone, yet there is no systematic difference for n ≥ 3. However, the average number of water molecules around H2SO4-NH2CH3 is consistently higher than that of H2SO4, and it is fairly independent of temperature and relative humidity.

Natural ventilation in underground wine cellars

The main objective of this research is to promote passive thermal design techniques in the construction of wineries. Natural ventilation in underground cellars is analyzed, focusing on the entrance tunnel, the ventilation chimney and the cave. A monitoring system was designed in order to detect changes in the indoor conditions and outdoor air infiltration. Monitoring process was carried out during one year. Results show the influence of outside temperature, ventilation chimney and access tunnel on the conditions inside the underground cellar. During hot periods, natural ventilation has a negligible influence on the indoor ambience, despite the permanently open vents in the door and chimney. The tunnel and ventilation chimney work as a temperature regulator, dampening outside fluctuations. Forced ventilation is necessary when a high air exchange ratio is needed. During cold periods, there is greater instability as a result of increased natural ventilation. The temperature differences along the tunnel are reduced, reflecting a homogenization and mixing of the air. The ventilation flow is sufficient to modify the temperature and relative humidity of the cave. Forced ventilation is not necessary in this period. During the intermediate periods --autumn and spring-- occurs different behaviors based on time of day.

Establishing Quercus ilex under Mediterranean dry conditions: sowing recalcitrant acorns versus planting seedlings at different depths and tube shelter light transmissions

Article New Forests November 2015, Volume 46, Issue 5, pp 869-883 First online: 17 June 2015 Establishing Quercus ilex under Mediterranean dry conditions: sowing recalcitrant acorns versus planting seedlings at different depths and tube shelter light transmissionsJuan A. OlietAffiliated withDepartamento de Sistemas y Recursos Naturales, E.T.S. Ingenieros de Montes, Universidad Politécnica de Madrid Email author View author's OrcID profile , Alberto Vázquez de CastroAffiliated withDepartamento de Sistemas y Recursos Naturales, E.T.S. Ingenieros de Montes, Universidad Politécnica de Madrid, Jaime PuértolasAffiliated withLancaster Environment Centre, Lancaster University $39.95 / €34.95 / £29.95 * Rent the article at a discount Rent now * Final gross prices may vary according to local VAT. Get Access AbstractSuccess of Mediterranean dry areas restoration with oaks is a challenging goal. Testing eco-techniques that mimic beneficial effects of natural structures and ameliorate stress contributes to positive solutions to overcoming establishment barriers. We ran a factorial experiment in a dry area, testing two levels of solid wall transmission of tube shelters (60 and 80 %) plus a control mesh, and two depths (shallow and 15 cm depth) of placing either planted seedlings or acorns of Quercus ilex. Microclimate of the planting or sowing spots was characterized by measuring photosynthetically active radiation, temperature and relative humidity. Plant response was evaluated in terms of survival, phenology, acorn emergence and photochemical efficiency (measured through chlorophyll fluorescence). We hypothesize that tube shelters and deep planting improve Q. ilex post-planting and sowing performance because of the combined effects of reducing excessive radiation and improving access to moist soil horizons. Results show that temperature and PAR was reduced, and relative humidity increased, in deep spots. Midsummer photochemical efficiency indicates highest level of stress for oaks in 80 % light transmission shelter. Optimum acorn emergence in spring was registered within solid wall tree shelters, and maximum summer survival of germinants and of planted seedlings occurred when acorns or seedlings were placed at 15 cm depth irrespectively of light transmission of shelter. Survival of germinants was similar to that of planted seedlings. The importance of techniques to keep high levels of viability after sowing recalcitrant seeds in the field is emphasized in the study

Caracterización de los barrios de bodegas subterráneas de la denominación de origen calificada Rioja. Estudio y comparación de sus condiciones interiores con las de las nuevas bodegas comerciales

Esta tesis pretende demostrar que las bodegas subterráneas suponen un modelo de construcción eficiente y medioambientalmente sostenible para la crianza y el almacenamiento de vinos. Durante la elaboración, crianza y almacenamiento del vino, las condiciones de temperatura y humedad relativa son determinantes en la calidad final del producto. La aparición de defectos en el vino como consecuencia de altas temperaturas durante el proceso crianza es algo conocido desde el siglo pasado, por lo que los enólogos tratan de alcanzar los parámetros que consideran idóneos para una correcta elaboración y envejecimiento del vino recurriendo en la mayoría de las bodegas a la climatización artificial. Las bodegas subterráneas son construcciones históricas en La Rioja y en el conjunto de los pueblos de la Denominación de Origen Calificada Rioja y el objetivo de esta tesis es demostrar que reúnen de forma natural las condiciones idóneas para la crianza del vino debido al diseño de su construcción y sin necesidad de emplear otras energías para conseguirlo. Además, la presencia de estas construcciones en la Denominación de Origen Calificada Rioja supone el origen de la fama de sus caldos y es un patrimonio cultural hoy en día sin explotar. Para demostrar la importancia de estos barrios de bodegas subterráneas, germen de la Denominación de Origen Calificada Rioja, se han inventariado los barrios de todos los municipios acogidos a ésta. Para ello se han visitado todos los municipios y se han fotografiado sus bodegas. En las visitas realizadas durante la catalogación se ha observado que constituyen hoy en día un patrimonio olvidado, que ha evolucionado hacia merenderos o viviendas, incluso en ocasiones abandonadas o derruidas. La conservación de las construcciones se ha cuidado más en la subzona de Rioja Alta, donde aún se pueden encontrar bodegas donde se elabora vino de forma particular, algo más excepcional de encontrar en La Rioja Baja. También se ha observado que los materiales de construcción de los calados empleados en La Rioja Alta suelen ser de piedra labrada o de sillería, mientras que en La Rioja Baja se recurre más a piedra de río o mampostería. Este trabajo se refleja en 2159 fichas que catalogan las bodegas subterráneas localizadas. Con objeto de demostrar que reúnen las condiciones adecuadas para la crianza, se han instalado sensores que han registrado la temperatura y la humedad relativa en las bodegas subterráneas y en bodegas comerciales de las que se diferencian tanto en el diseño constructivo como en las soluciones adoptadas por estas para reunir los parámetros buscados. Los resultados obtenidos en las bodegas subterráneas muestran que estas construcciones tradicionales presentan menos oscilaciones anuales de temperatura y humedad relativa que las salas de crianza de bodegas comerciales, lo que implica una solución constructiva más adecuada para la crianza y conservación del vino. Para corroborar los resultados obtenidos sobre las condiciones interiores, se ha realizado un análisis sensorial de vinos almacenados y criados en bodegas subterráneas comparándolos con los almacenados sin estar sometidos a un control de estos parámetros, como se puede dar en condiciones domésticas, una vez comercializados cuando el enólogo pierde el control sobre ellos. Los resultados demuestran que los vinos almacenados en domicilios particulares presentan diferencias con los almacenados en bodegas subterráneas. Estos resultados son acordes con los datos obtenidos de los sensores colocados en estas bodegas subterráneas, donde la temperatura máxima anual no supera los 20ºC, considerada como umbral máximos permitido durante la crianza por varios autores. ABSTRACT This thesis aims to demonstrate that the underground cellars represent a model of efficient construction and environmentally sustainable for aging and storing wines. During the production, aging and storing wine, temperature and relative humidity are crucial to the final product quality. The appearance of defects in wine as a result of high temperatures during the aging process is something known since the last century, so that winemakers seek to achieve the parameters considered suitable for proper production and aging of wine using the most wineries to artificial air conditioning. The underground cellars are historical buildings in La Rioja and all the peoples of the Designation of Origin Rioja and the aim of this thesis is to demonstrate that naturally meet the conditions for aging wine due to its construction design and without the use of other energy to get it. Furthermore, the presence of these buildings in the Rioja Denomination of Origin represents the origin of the fame of its wines and is a cultural heritage today untapped. To demonstrate the importance of these areas of underground cellars, germ of the Designation of Origin Rioja, they have been inventoried all the districts of municipalities benefiting from this. This will have visited all municipalities and have photographed their cellars. In visits made during cataloging it has been observed that constitute today a forgotten heritage that has evolved to picnic or homes, sometimes even abandoned or demolished. The conservation of the buildings has been more careful in the subzone of Rioja Alta, where you can still find wine cellars where a particular way, something exceptional to find in La Rioja Baja is made. It has also been observed that the building materials used in the drafts La Rioja Alta usually carved stone or masonry, while in La Rioja Baja is most uses of river stone or masonry. This work is reflected in 2159 cataloging records located underground cellars. In order to demonstrate that they meet the conditions suitable for breeding they were installed sensors that recorded the temperature and relative humidity in the underground cellars and commercial wineries which differ both in the building design and the solutions adopted by sought to gather these parameters. The results obtained in the underground cellars show that these traditional buildings have fewer annual fluctuations of temperature and relative humidity of the aging rooms commercial wineries, which implies a more constructive solution suitable for the breeding and conservation of wine. To corroborate the results obtained on domestic conditions, has made a sensory analysis of wines stored and raised underground cellars compared with stored without being subjected to control these parameters, as can occur in domestic conditions, once marketed as winemaker loses control over them. The results show that the wines stored in private homes have differences with those stored in underground cellars. These results are consistent with data obtained from sensors placed in these underground cellars, where the maximum annual temperature is below 20 ° C, considered as maximum allowable threshold for raising by various authors.

Impedance spectroscopy study of the effect of environmental conditions in the microstructure development of OPC and slag cement mortars

In this work, the microstructure of mortars made with an ordinary Portland cement and slag cement has been studied. These mortars were exposed to four different constant temperature and relative humidity environments during a 180-day period. The microstructure has been studied using impedance spectroscopy, and mercury intrusion porosimetry as a contrast technique. The impedance spectroscopy parameters make it possible to analyze the evolution of the solid fraction formation for the studied mortars and their results are confirmed with those obtained using mercury intrusion porosimetry. The development of the pore network of mortars is affected by the environment. However, slag cement mortars are more influenced by temperature while the relative humidity has a greater influence on the OPC mortars. The results show that slag cement mortars hardened under non-optimal environments have a more refined microstructure than OPC mortars for the studied environmental conditions.

Surfactant coated aerosol powders and their properties

The hygroscopic growth of aerosols is an important factor effecting particle size. The consequence of the hygroscopic growth of pharrnaceutical aerosols is a change in their deposition characteristics, such that there is an increase in the total amount deposited in the lung. In this study the hygroscopic growth of disodium fluorescein (DF) aerosol powders was investigated by coating the powders with lauric and capric acids. The coating procedure was carried out in dichloromethane and chloroform, which acted as cosolvents for the fatty acids. An assessment of the extent and the nature of the coating was carried out. The qualitative assessment of the coating was achieved by infra-red spectroscopy, electronscanning chemical analysis and scanning electron microscopy. The quantitative analysis was carried out by differential refractometry, ultra-violet spectroscopy and gas liquid chromatography. These powders were generated under conditions approaching those in the lung, of 97 % relative humidity and 37"C. Coated and uncoated DF aerosol powders were introduced into a controlled temperature and relative humidity apparatus, designed and constructed for the investigation of hygroscopic growth in these studies. A vertical spinning disc device was used to generate the powders. Under conditions of controlled temperature and relative humidity mentioned, the growth ratio of disodium fluorescein alone was 1.45 compared with 1.68, for a nominal coating of DF with lauric acid of 0.12 gg-1, 1.0 for a nominal lauric acid coating of 0.2 gg-1, and 1.02 for a nominal capric acid coating of 0.18 gg-1. The range of control of hygroscopic growth of these aerosols has implications for the deposition of these preparations in the respiratory tract. These implications are discussed in the light of the current knowledge of the effects of hygroscopic growth on the deposition of pharmaceutical and environmental aerosols. A series of experiments in which pulmonary ventilation using a simple radioaerosol generator and delivery system are reported showing that particle size determination may be used to aid the design of diagnostic aerosol generators.

The effect of flying and low humidity on the admittance of the tympanic membrane and middle ear system

Many passengers experience discomfort during flight because of the effect of low humidity on the skin, eyes, throat, and nose. In this physiological study, we have investigated whether flight and low humidity also affect the tympanic membrane. From previous studies, a decrease in admittance of the tympanic membrane through drying might be expected to affect the buffering capacity of the middle ear and to disrupt automatic pressure regulation. This investigation involved an observational study onboard an aircraft combined with experiments in an environmental chamber, where the humidity could be controlled but could not be made to be as low as during flight. For the flight study, there was a linear relationship between the peak compensated static admittance of the tympanic membrane and relative humidity with a constant of proportionality of 0.00315 mmho/% relative humidity. The low humidity at cruise altitude (minimum 22.7 %) was associated with a mean decrease in admittance of about 20 % compared with measures in the airport. From the chamber study, we further found that a mean decrease in relative humidity of 23.4 % led to a significant decrease in mean admittance by 0.11 mmho [F(1,8) = 18.95, P = 0.002], a decrease of 9.4 %. The order of magnitude for the effect of humidity was similar for the flight and environmental chamber studies. We conclude that admittance changes during flight were likely to have been caused by the low humidity in the aircraft cabin and that these changes may affect the automatic pressure regulation of the middle ear during descent. © 2013 Association for Research in Otolaryngology.

Application and use of isothermal calorimetry in pharmaceutical development

There are many steps involved in developing a drug candidate into a formulated medicine and many involve analysis of chemical interaction or physical change. Calorimetry is particularly suited to such analyses as it offers the capacity to observe and quantify both chemical and physical changes in virtually any sample. Differential scanning calorimetry (DSC) is ubiquitous in pharmaceutical development, but the related technique of isothermal calorimetry (IC) is complementary and can be used to investigate a range of processes not amenable to analysis by DSC. Typically, IC is used for longer-term stability indicating or excipient compatibility assays because both the temperature and relative humidity (RH) in the sample ampoule can be controlled. However, instrument design and configuration, such as titration, gas perfusion or ampoule-breaking (solution) calorimetry, allow quantification of more specific values, such as binding enthalpies, heats of solution and quantification of amorphous content. As ever, instrument selection, experiment design and sample preparation are critical to ensuring the relevance of any data recorded. This article reviews the use of isothermal, titration, gas-perfusion and solution calorimetry in the context of pharmaceutical development, with a focus on instrument and experimental design factors, highlighted with examples from the recent literature. © 2011 Elsevier B.V.

An investigation of environmental conditions experienced during the life of high-value wood components and products

Australian forest industries have a long history of export trade of a wide range of products from woodchips (for paper manufacturing), sandalwood (essential oils, carving and incense) to high value musical instruments, flooring and outdoor furniture. For the high value group, fluctuating environmental conditions brought on by changes in temperature and relative humidity, can lead to performance problems due to consequential swelling, shrinkage and/or distortion of the wood elements. A survey determined the types of value-added products exported, including species and dimensions packaging used and export markets. Data loggers were installed with shipments to monitor temperature and relative humidity conditions. These data were converted to timber equilibrium moisture content values to provide an indication of the environment that the wood elements would be acclimatising to. The results of the initial survey indicated that primary high value wood export products included guitars, flooring, decking and outdoor furniture. The destination markets were mainly located in the northern hemisphere, particularly the United States of America, China, Hong Kong, Europe (including the United Kingdom), Japan, Korea and the Middle East. Other regions importing Australian-made wooden articles were south-east Asia, New Zealand and South Africa. Different timber species have differing rates of swelling and shrinkage, so the types of timber were also recorded during the survey. Results from this work determined that the major species were ash-type eucalypts from south-eastern Australia (commonly referred to in the market as Tasmanian oak), jarrah from Western Australia, spotted gum, hoop pine, white cypress, black butt, brush box and Sydney blue gum from Queensland and New South Wales. The environmental conditions data indicated that microclimates in shipping containers can fluctuate extensively during shipping. Conditions at the time of manufacturing were usually between 10 and 12% equilibrium moisture content, however conditions during shipping could range from 5 (very dry) to 20% (very humid). The packaging systems incorporated were reported to be efficient at protecting the wooden articles from damage during transit. The research highlighted the potential risk for wood components to ‘move’ in response to periods of drier or more humid conditions than those at the time of manufacturing, and the importance of engineering a packaging system that can account for the environmental conditions experienced in shipping containers. Examples of potential dimensional changes in wooden components were calculated based on published unit shrinkage data for key species and the climatic data returned from the logging equipment. The information highlighted the importance of good design to account for possible timber movement during shipping. A timber movement calculator was developed to allow designers to input component species, dimensions, site of manufacture and destination, to see validate their product design.

Índice de previsão de produção de leite para vacas Jersey

In Brazil the adoption of several models of cattle confinement leads to special conditions for management methods in dairy production, which can be improved by the use of technology that assures better herd management. Indexes relating environmental variables to production are applied for the prediction of milk production. The values of temperature and relative humidity, rain index, solar radiation and pasture soil temperature are generally considered potential stress agents for cows. The objective of this research was to develop an index for predicting milk production for high productivity Jersey milking cows lodged in semi confinement in tropical conditions. The experiment considered two treatments: A - the cows waited for 30 minutes prior to milking in a room with a shower associated to a fan; B - the cows did not have access to this room (control). Other than the waiting period, the cows had access to pasture. Differences in the effect of average production were not statistically significant. The analysis for studying the effect of the variables and designing the model led to a statistical model relating the variables milk production and rain index, as well as the maximum soil temperature of pasture, and milk production.

Identificação eletrônica para avaliação do comportamento dos suínos na fase de gestação

The efficiency of swine production performance depends on the herd administration, such as good nutrition, sanitary control, facilities and appropriate environmental conditions. The concept of this production model is directly related with the reduction of selective losses and the process control. Each production segment is controlled to reach the optimization in the system totality, it is necessary to apply animals handling concepts, environmental control implementation, diseases control, nutrition control, information concerning in guaranteeing the animal welfare and individual identification. The present work presents as objective the development of the mathematical model to evaluate interactions among the internal atmosphere of the installation and the thermal animals preference, in the expectation of detecting a relationship among the frequency access to the drinking fountain and the atmosphere conditions - temperature, black globe temperature and relative humidity, using as tool the electronic identification. The results obtained by the mathematical model, allowed to conclude accurately the evaluation of the swine thermal preference correlating with the climatic variables in the pregnancy stage.

Unidade Haugh como medida da qualidade de ovos de galinha armazenados sob refrigeração

Alterations in physical, chemical and functional characteristics of egg proteins occur during storage. These changes depend on the storage conditions, mainly duration, temperature and relative humidity. This study examined the fresh egg Haugh unit score and the storage egg Haugh unit score, at room temperature (25°C) and under refrigeration conditions (8°C), during 7, 14 and 21 days of storage. Haugh units and albumin height decreased considerably during storage at room temperature. At 8°C, there was no significant difference in the Haugh unit for different periods of storage, but their values were smaller as compared to fresh eggs. The weight of the eggs was not affected by both storage and temperature. For both temperatures, pH was positively correlated with Haugh units and negatively with the albumin height.