Effects of condensation in microchannels with a porous boundary: analytical investigation on heat transfer and meniscus shape

In two-phase miniature and microchannel flows, the meniscus shape must be considered due to effects that are affected by condensation and/or evaporation and coupled with the transport phenomena in the thin film on the microchannel wall, when capillary forces drive the working fluid. This investigation presents an analytical model for microchannel condensers with a porous boundary, where capillary forces pump the fluid. Methanol was selected as the working fluid. Very low liquid Reynolds numbers were obtained (Re~6), but very high Nusselt numbers (Nu~150) could be found due to the channel size (1.5 mm) and the presence of the porous boundary. The meniscus calculation provided consistent results for the vapor interface temperature and pressure, as well as the meniscus curvature. The obtained results show that microchannel condensers with a porous boundary can be used for heat dissipation with reduced heat transfer area and very high heat dissipation capabilities.

Modeling of Liquid-Solid Flow in Industrial Scale

In the present work, liquid-solid flow in industrial scale is modeled using the commercial software of Computational Fluid Dynamics (CFD) ANSYS Fluent 14.5. In literature, there are few studies on liquid-solid flow in industrial scale, but any information about the particular case with modified geometry cannot be found. The aim of this thesis is to describe the strengths and weaknesses of the multiphase models, when a large-scale application is studied within liquid-solid flow, including the boundary-layer characteristics. The results indicate that the selection of the most appropriate multiphase model depends on the flow regime. Thus, careful estimations of the flow regime are recommended to be done before modeling. The computational tool is developed for this purpose during this thesis. The homogeneous multiphase model is valid only for homogeneous suspension, the discrete phase model (DPM) is recommended for homogeneous and heterogeneous suspension where pipe Froude number is greater than 1.0, while the mixture and Eulerian models are able to predict also flow regimes, where pipe Froude number is smaller than 1.0 and particles tend to settle. With increasing material density ratio and decreasing pipe Froude number, the Eulerian model gives the most accurate results, because it does not include simplifications in Navier-Stokes equations like the other models. In addition, the results indicate that the potential location of erosion in the pipe depends on material density ratio. Possible sedimentation of particles can cause erosion and increase pressure drop as well. In the pipe bend, especially secondary flows, perpendicular to the main flow, affect the location of erosion.

Weed control under integrated nutrient management systems in faba bean (Vicia faba) production in Egypt

Two field experiments were conducted in two successive seasons, 2005/2006 and 2006/2007, to determine whether management can improve faba bean competitiveness with weeds, thus helping to achieve its yield potential. The experiment included five treatments, composed of organic and mineral fertilizers, alone and mixed at different rates, along with a control and six weed control treatments, including oxadiargyl, prometryn, hand hoeing treatments alone or mixed with the herbicides, and a nonweeded treatment (control).The herbicide treatments were not superior to the two hand-hoeing treatments. Using compost favored growth and yield of faba bean more than of weeds. Adding fertilizer also improved most yield parameters. Application of compost alone or combined with 50 or 100% of the recommended NPK rate improved faba bean growth in terms of net assimilation rate, specific leaf area, and leaf weight ratio as components of relative growth rate. This improvement in growth resulted in increase of seed yield, yield components and protein of faba bean. Faba bean yield performance improved under interactive fertilizer effects and weed control treatments as growth improved, as a result of nutrient release from fertilizers and weed control.

Growth, nodulation, and yield of soybean and associated weeds as affected by weed management

Two field experiments were conducted at the experimental farm of the National Research Centre at Shalakan, Kalubia Governorate, Egypt, during 2006 and 2007 seasons, to study the effect of three pre-emergence herbicides, prometryn [at the rate of 0.75, 1.5 and 2.25 kg ha-1], oxadiargyl [at the rate of 240, 480 and 720 g ha-1] and butralin [at the rate of 1.20, 2.40 and 3.36 kg ha-1], two hand hoeing treatments and a nonweeded check, on weed infestation, nodulation, growth, yield and yield attributes of soybean plants. Two hand hoeing treatments resulted in the highest weed depression expressed as the lowest fresh and dry weights of broadleaved, grassy and total weeds. The reduction percentage in weed dry matter compared to the nonweeded treatment was 98.3, 92.64 and 96.9% in broadleaved, grassy and total weeds, respectively. Application of the three herbicides at higher or recommended doses significantly reduced fresh and dry weight of the weeds compared to the nonweeded treatment. The results indicated that all the three herbicides at rates higher than the recommended markedly decreased the number, fresh and dry weight of nodules as well as root, shoot and total dry weight plant-1, while application of two hand hoeing treatments significantly increased these traits. Two hand hoeing treatments and pre-emergence herbicides at the recommended rates markedly increased soybean yield and its attributes. Two hand hoeing treatments gave the highest values of number of pods per plant-1, weight of pods per plant-1 and number of seeds per plant-1 by 140.7, 150.0 and 59.8%, respectively, compared to the nonweeded treatment. On the other hand, oxadiargyl at the recommended rate (480 g ha-1) was the best treatment for promoting seed yield (g plant-1), seed yield (kg ha-1) and biological yield (g plant-1) compared to the nonweeded treatment by 87.3, 85.0 and 88.2%, respectively. Prometryn at the rate of 1.50 kg ha-1, followed by two hand hoeing treatments, produced the highest shoot and seed protein percentage as well as seed oil percentage, compared to the other weed control treatments.

Multispecies weed competition and their economic threshold on the wheat crop

Two field experiments were conducted to evaluate the effects of multispecies weed competition on wheat grain yield and to determine their economic threshold on the crop. The experiments were conducted in 2002, on two sites in Iran: at the Agricultural Research Station on Ferdowsi University of Mashhad (E1) and on the fields of Shirvan's Agricultural College (E2). A 15 x 50 m area of a 15 ha wheat field in E1 and a 15 x 50 m area of a 28 ha wheat field in E2 were selected as experimental sites. These areas were managed like other parts of the fields, except for the use of herbicides. At the beginning of the shooting stage, 30 points were randomly selected by dropping a 50 x 50 cm square marker on each site. The weeds present in E1 were: Avena ludoviciana, Chenopodium album, Solanum nigrum, Stellaria holostea, Convolvulus spp., Fumaria spp., Sonchus spp., and Polygonum aviculare. In E2 the weeds were A. ludoviciana, Erysimum sp., P. aviculare, Rapistrum rugosum, C. album, Salsola kali, and Sonchus sp. The data obtained within the sampled squares were submitted to regression equations and weeds densities were calculated in terms of TCL (Total Competitive Load). The regression analysis model indicated that only A. ludoviciana, Convolvulus spp. and C. album, in E1; and A. ludoviciana, S. kali, and R. rugosum, in E2 had a significant effect on the wheat yield reduction. Weed economic thresholds were 5.23 TCL in E1 and 6.16 TCL in E2; which were equivalent to 5 plants m-2 of A. ludoviciana or 12 plants m-2 of Convolvulus spp. or 19 plants m-2 of C. album in E1; and 6 plants m-2 A. ludoviciana, 13 plants m-2 S. kali and 27 plants m-2 R. rugosum in E2. Simulations of economic weed thresholds using several wheat grain prices and weed control costs allowed a better comparison of the experiments, suggesting that a more competitive crop at location E1 than at E2 was the cause of a lower weed competitive ability at the first location.

Sulfentrazone efficiency on Ipomoea hederifolia and Ipomoea quamoclit as influenced by rain and sugarcane straw

The aim of this study was to assess the capacity of sulfentrazone applied in pre-emergence in controlling Ipomoea hederifolia and Ipomoea quamoclit as a function of the time interval between herbicide application and the occurrence of rain, and the presence of sugarcane straw on the soil surface. Two greenhouse experiments and one field experiment were conducted. For the greenhouse experiments, the study included three doses of sulfentrazone applied by spraying 0, 0.6, and 0.9 kg ha-1, two amounts of straw on the soil (0 and 10 t ha-1), and five time intervals between the application of herbicide and rain simulation (0, 20, 40, 60, and 90 days). In the field experiment, five herbicide treatments (sulfentrazone at 0.6 and 0.9 kg ha-1, sulfentrazone + hexazinone at 0.6 + 0.25 kg ha-1, amicarbazone at 1.4 kg ha-1, and imazapic at 0.147 kg ha-1) and two controls with no herbicide were studied. Management conditions with or without sugarcane straw on the soil were also assessed. From the greenhouse experiments, sulfentrazone application at 0.6 kg ha-1 was found to provide for the efficient control of I. hederifolia and I. quamoclit in a dry environment, with up to 90 days between herbicide application and rain simulation. After herbicide application, 20 mm of simulated rain was enough to leach sulfentrazone from the straw to the soil, as the biological effects observed in I. hederifolia and I. quamoclit remained unaffected. Under field conditions, either with or without sugarcane straw left on the soil, sulfentrazone alone (0.6 or 0.9 kg ha-1) or sulfentrazone combined with hexazinone (0.6 + 0.25 kg ha-1) was effective in the control of I. hederifolia and I. quamoclit, exhibiting similar or better control than amicarbazone (1.4 kg ha-1) and imazapic (0.147 kg ha-1).

Effect of desiccation and salinity stress on seed germination and initial plant growth of Cucumis melo

Smellmelon, an annual invasive weed of soybean production fields in the north of Iran, reproduces and spreads predominately through seed production. This makes seed bank survival and successful germination essential steps in the invasive process. To evaluate the potential of Smellmelon to invade water-stressed environments, laboratory studies were conducted to investigate the effect of desiccation and salinity at different temperatures on seed germination and seedling growth of Cucumis melo. Seeds were incubated at 25, 30, 35 and 40 ºC in the darkness in a solution (0, -0.2, -0.4, -0.6, -0.8, 1 and 1.2 MPa) of a salt (NaCl), and in a solution (0, -2, -4, -6, -8, -10, -12 bar) of PEG-6000 (Polyethylene glycol), in two separate experiments. The results showed that the highest percentage and rate of germination occurred at 35 ºC in salt concentrations of 0, -0.2, -0.4 MPa and PEG concentrations of 0, -2, -4 bar. Increasing the concentration of salt (NaCl) and PEG limited germination, seedling growth and water uptake but increased the sodium content in the seedlings. No significant difference was observed among 0, -0.2 and -0.4 MPa of NaCl and among 0, -2 and -4 bar of PEG concentration at 35 ºC. The negative effects of PEG were more than those of NaCl on germination percentage and germination rate. Increased stress levels lead to reduction of root and shoot length, and SVL of seedlings. Na+ content of seedling decreased with limited seedling growth of C. melo.

Levels of nutrients and grain yield of maize intercropped with signalgrass (Brachiaria) in different arrangements of plants

Competition between maize and signalgrass can economically cripple the intercropping by the reduced yield of maize and dry matter content of the forage. In seeking to define plant arrangements which make this system more efficient, this research was held with the objective of assessing the effects of interference of densities of signalgrass (Urochloa Brizantha) on nutrition and on maize grain yield. Two field experiments were conducted in a randomized block design with four replications. Treatments were arranged similarly in both experiments, in a 2 x 4 factorial design, the first factor being the dose of Nicosulfuron herbicide applied (0 and 8 g ha-1) and the second factor being the forage seeding rates (0, 2, 4 and 6 kg of seeds per hectare). The interference of signalgrass reduced foliar nitrogen, potassium and phosphorus content in maize plants intercropped with the forage. Higher values of grain yield were observed with the reduction of the spacing and the application of the recommended herbicide underdose (8 g ha-1). It was concluded that, regardless of the seeding density of U. Brizantha, reducing the maize seeding inter-rows spacing, combined with the application of an underdose of Nicosulfuron, caused a positive effect by reducing the initial forage growth, resulting in less interference of Urochloa brizantha on nutrient uptake by the maize plants and grain yield of the crop.

Eggplant (Solanum melongena) infusion has a modest and transitory effect on hypercholesterolemic subjects

Eggplant (Solanum melongena) is consumed extensively in Brazil. It has been believed that infusion of a powdered preparation of the fruit may reduce serum cholesterol. However, there are few documented reports on its effects on cholesterol metabolism and its possible hypocholesterolemic effect has not been proved by well-controlled studies. The aim of the present study was to observe the effects of S. melongena on the serum cholesterol and triglycerides of 38 hypercholesterolemic human volunteers ingesting S. melongena infusion for five weeks. Thirty-eight hypercholesterolemic subjects receiving either S. melongena infusion (N = 19) or placebo (N = 19) participated in two clinical experiments in which the effect of S. melongena infusion was studied with (N = 16) or without (N = 38) dietary orientation. Total cholesterol and its fractions, triglycerides, and apolipoproteins A and B were measured in blood at the beginning of the experiment and three and five weeks thereafter. No differences were observed compared to control. Intraindividual analysis showed that S. melongena infusion significantly reduced the blood levels of total and LDL cholesterol and of apolipoprotein B. After dietary orientation, no intra- or intergroup differences were seen for any of the parameters analyzed. The results suggest that S. melongena infusion had a modest and transitory effect, which was not different from that obtained with standard orientation for dyslipidemia patients (diet and physical activities).

Building a Roadmap for a Market Intelligence function in a Global B2B company

Tämän diplomityötutkimuksen tarkoituksena on luoda markkinaälyyn (MI) erikoistunut funktio suurelle, globaalisti toimivalle B2B-yritykselle. Tämän päivän muut-tuvilla markkinoilla, teollisuusyrityksen on oltava markkinalähtöinen selviytyäkseen. Markkinatiedon tehokas hyödyntäminen ei pelkästään luo tietoa markkinoista, vaan tuottaa kilpailukykyistä tietoa ja toimii strategisen päätöksenteon tukena pitkällä aikavälillä. Tämä tutkimus on kvalitatiivinen toimintatutkimus, joka sisältää kirjallisuuskat-sauksen, yritystapaustutkimuksen sekä syväanalyysin yrityksen MI-ympäristöstä. Kirjallisuuskatsaus pitää sisällään teoriaa liittyen markkinaälyyn useassa eri kon-tekstissa, asiakassuhteeseen, sekä prosessinmallintamiseen. Empiiriseen osaa seuraa tutkimusmenetelmäkappale, joka sisältää kaksivaiheisen tutkimuksen mukaan lu-kien 20 päällikkötason haastattelua sekä yhden laaja-alaisen työryhmätapaamisen. Työn tuloksena syntyy kolmivaiheinen tiekartta, jonka tarkoitus on toimia pohjana uuden MI-funktion rakentamiselle Case-yrityksessä. Tuloksen mukaan MI-funktio tulisi sijoittaa yrityksen asiakasrajapintaan sekä tukea yksiköiden välistä integraa-tiota. Markkinaälyn jakaminen yrityksen sisällä vaatii käytäntöjen, tarpeiden ja ta-voitteiden systemaattista viestintää eri organisaatiotasoille, jotta yritys voi edelleen saada asiakkaalta tarpeeseen vastaavaa tietoa. Viestintä yrityksen ja asiakkaan välil-lä on oltava molemminpuolista, jotta tulokset voisivat parantaa asiakassuhdetta. Kun asiakassuhde paranee, yritys voi oppia asiakkaalta arvokasta tietoa, markkinaälyä.

Kaksifaasijäähdytysjärjestelmään liittyvien pumppujen vertailu ja kehittäminen sarjatuotannon tarpeisiin

Tehoelektroniikalta vaaditaan nykyään parempaa suorituskykyä entistä pienemmässä tilassa. Tämä luo haasteen riittävälle jäähdytykselle. Eräs ratkaisu on käyttää kaksifaasijäähdytystä, jolla aikaansaadaan tehokas lämmönsiirto komponenttien pinnalta. Lämmönsiirtonesteinä voidaan käyttää kylmäaineita tai muita alhaisessa lämpötilassa kiehuvia nesteitä. Tällaisille nesteille on tyypillistä alhainen höyrynpaine sekä matala viskositeetti. Nämä ominaisuudet tuovat haasteita nesteen pumppaukseen. Tässä työssä tarkastellaan R-134A:ta sekä Novec 7000:ta, perehdytään niiden fysikaalisiin ominaisuuksiin sekä materiaaliyhteensopivuuksiin ja näiden tietojen pohjalta etsitään sopivaa pumpputyyppiä kaksifaasijäähdytysjärjestelmään. Tehoelektroniikan jäähdytysjärjestelmän pumpun on oltava edullinen muuhun järjestelmään nähden. Tyypillinen kiertopumppu nestejäähdytysjärjestelmässä on pieni keskipakopumppu. Alhaisen kiehumispisteen vuoksi kavitointiriski kasvaa ja tämä voi vahingoittaa pumppua. Myös matala viskositeetti tuo haasteita vuotoherkkyyden kasvamisen myötä, joten mekaanisilla aksiaalitiivisteillä varustetut pumput eivät ole pitkäikäisiä. Kylmäainejärjestelmiin tarkoitetut pumput ovat arvokkaita, eikä näin ollen sovellu edullisiin jäähdytysjärjestelmiin. Tässä työssä käydään läpi erilaisia pumpputyyppejä, jotka voisivat soveltua pitkäikäiseen pumppaukseen ilman huoltotöitä. Näiden tietojen perusteella kehitetään edullista ja pitkäikäistä pumppua pieniin kaksifaasijäähdytysjärjestelmiin nesteiden fysikaaliset ominaisuudet huomioon ottaen. Kehitetyn pumpun ominaisuuksia ja kustannuksia vertaillaan kaupallisiin ratkaisuihin ottaen huomioon sarjavalmistus. Itse valmistettuna pienelle sisäryntöiselle hammaspyöräpumpulle jää hintaa alle kymmenesosa markkinoilta löytyviin kylmäaineille soveltuviin pumppuun.

An electronic pressure-meter nociception paw test for mice

The aim of the present investigation was to describe and validate an electronic mechanical test for quantification of the intensity of inflammatory nociception in mice. The electronic pressure-meter test consists of inducing the animal hindpaw flexion reflex by poking the plantar region with a polypropylene pipette tip adapted to a hand-held force transducer. This method was compared to the classical von Frey filaments test in which pressure intensity is automatically recorded after the nociceptive hindpaw flexion reflex. The electronic pressure-meter and the von Frey filaments were used to detect time versus treatment interactions of carrageenin-induced hypernociception. In two separate experiments, the electronic pressure-meter was more sensitive than the von Frey filaments for the detection of the increase in nociception (hypernociception) induced by small doses of carrageenin (30 µg). The electronic pressure-meter detected the antinociceptive effect of non-steroidal drugs in a dose-dependent manner. Indomethacin administered intraperitoneally (1.8-15 mg/kg) or intraplantarly (30-300 µg/paw) prevented the hypersensitive effect of carrageenin (100 µg/paw). The electronic pressure-meter also detected the hypernociceptive effect of prostaglandin E2 (PGE2; 10-100 ng) in a dose-dependent manner. The hypernociceptive effect of PGE2 (100 ng) was blocked by dipyrone (160 and 320 µg/paw) but not by intraplantar administration of indomethacin (300 µg/paw). The present results validate the use of the electronic pressure-meter as more sensitive than the von Frey filaments in mice. Furthermore, it is an objective and quantitative nociceptive test for the evaluation of the peripheral antinociceptive effect of anti-inflammatory analgesic drugs, which inhibit prostaglandin synthesis (indomethacin) or directly block the ongoing hypernociception (dipyrone).

Readout architectures for hybrid pixel detector readout chips

The original contribution of this thesis to knowledge are novel digital readout architectures for hybrid pixel readout chips. The thesis presents asynchronous bus-based architecture, a data-node based column architecture and a network-based pixel matrix architecture for data transportation. It is shown that the data-node architecture achieves readout efficiency 99% with half the output rate as a bus-based system. The network-based solution avoids “broken” columns due to some manufacturing errors, and it distributes internal data traffic more evenly across the pixel matrix than column-based architectures. An improvement of > 10% to the efficiency is achieved with uniform and non-uniform hit occupancies. Architectural design has been done using transaction level modeling (TLM) and sequential high-level design techniques for reducing the design and simulation time. It has been possible to simulate tens of column and full chip architectures using the high-level techniques. A decrease of > 10 in run-time is observed using these techniques compared to register transfer level (RTL) design technique. Reduction of 50% for lines-of-code (LoC) for the high-level models compared to the RTL description has been achieved. Two architectures are then demonstrated in two hybrid pixel readout chips. The first chip, Timepix3 has been designed for the Medipix3 collaboration. According to the measurements, it consumes < 1 W/cm^2. It also delivers up to 40 Mhits/s/cm^2 with 10-bit time-over-threshold (ToT) and 18-bit time-of-arrival (ToA) of 1.5625 ns. The chip uses a token-arbitrated, asynchronous two-phase handshake column bus for internal data transfer. It has also been successfully used in a multi-chip particle tracking telescope. The second chip, VeloPix, is a readout chip being designed for the upgrade of Vertex Locator (VELO) of the LHCb experiment at CERN. Based on the simulations, it consumes < 1.5 W/cm^2 while delivering up to 320 Mpackets/s/cm^2, each packet containing up to 8 pixels. VeloPix uses a node-based data fabric for achieving throughput of 13.3 Mpackets/s from the column to the EoC. By combining Monte Carlo physics data with high-level simulations, it has been demonstrated that the architecture meets requirements of the VELO (260 Mpackets/s/cm^2 with efficiency of 99%).

Aamiaiskahvilasta ötökkätarjontaan. Suomen kirjoitetun yleiskielen morfosyntaktisten yhdyssanarakenteiden produktiivisuus

Tämän tutkimuksen kohde on suomen kirjoitetun yleiskielen morfosyntaktisten yhdyssanarakenteiden produktiivisuus. Tutkimuksen tärkein päämäärä on selvittää, kuinka ahkerasti erilaisia suomen kielen suomia mahdollisuuksia käytetään uusien yhdyssanojen muodostuksessa. Käytännöllistä produktiivisuutta kartoittava tutkimus täydentää kielioppien ja sanastonkuvausten antamaa kuvaa kielestä. Tutkimuksen kohteena oleva kielimuoto on kaikille kielenkäyttäjille yhteinen kirjoitettu yleiskieli. Tutkimusaineisto koostuu 28 091 uudesta yhdyssanasta, jotka on kerätty painetun median kielestä vuosina 2000–2009. Aineiston pohjana on Kotimaisten kielten keskuksen Nykysuomen sanastotietokanta, johon poimitaan uusia ja uudella tavalla käytettyjä sanoja ensisijaisesti sanakirjatyön ja kielenhuollon tarpeisiin. Tutkimusaihetta lähestytään useiden yhdyssanan osien muotoa, sanaluokkaa, määrää ja pituutta koskevien alakysymysten kautta. Tutkimus etenee yksittäisten muut-tujien käsittelystä muuttujien keskinäisiä suhteita tarkasteleviin malleihin. Tutkimuksessa käytetään kaksivaiheista metodia: Metodin ensimmäinen askel on uudessa sanastossa havaittujen rakenteiden tyyppifrekvenssin tilastollinen analyysi. Toinen askel on varsinkin matalafrekvenssisten tai tilastollisessa analyysissa muuten poikkeavaksi osoittautuneiden rakenteiden kvalitatiivinen tarkastelu. Metodi on kehitetty tätä tutkimusta varten, sillä aiemmin produktiivisuuden mittaamisessa käytetyt menetelmät eivät sellaisenaan sovi suomen kielen yhdyssanarakenteiden tutkimukseen. Tutkimusmetodien kehittäminen on tutkimuksen keskeinen tavoite. Tutkimus osoittaa, että suomen kielen uudet yhdyssanat ovat rakenteeltaan homogeenisempiä, kuin aiempia kielenkuvauksia lukemalla voisi olettaa. Uusi suomen kielen yhdyssana on todennäköisimmin kahdesta substantiivista yhdistämällä muodostettu substantiivi, jonka alkuosa on nominatiivissa eikä kongruoi jälkiosan kanssa. Ennakko-oletusta huomattavasti yleisempiä ovat myös prefiksinkaltaisella alkuosalla alkavat yhdyssanat. Genetiivialkuiset yhdyssanat puolestaan ovat ennakko-oletusta harvinaisempia. Kaikki kieliopillisesti mahdolliset yhdyssanarakenteet eivät ole lainkaan produktiivisia kielenkäytön tasolla. Tutkimus on luonteeltaan kielen rakennetta kartoittavaa perustutkimusta. Tutkimustulosten tärkeimmät sovellusalat ovat kieliteknologia ja sananmuodostuksen opetus. Tutkimus avaa useita näkökulmia jatkotutkimukselle.

Flow in porous media of oil-water systems

Fluid flow behaviour in porous media is a conundrum. Therefore, this research is focused on filtration-volumetric characterisation of fractured-carbonate sediments, coupled with their proper simulation. For this reason, at laboratory rock properties such as pore volume, permeability and porosity are measured, later phase permeabilities and oil recovery in function of flow rate are assessed. Furthermore, the rheological properties of three oils are measured and analysed. Finally based on rock and fluid properties, a model using COMSOL Multiphysics is built in order to compare the experimental and simulated results. The rock analyses show linear relation between flow rate and differential pressure, from which phase permeabilities and pressure gradient are determined, eventually the oil recovery under low and high flow rate is established. In addition, the oils reveal thixotropic properties as well as non-Newtonian behaviour described by Bingham model, consequently Carreau viscosity model for the used oil is given. Given these points, the model for oil and water is built in COMSOL Multiphysics, whereupon successfully the reciprocity between experimental and simulated results is analysed and compared. Finally, a two-phase displacement model is elaborated.