Structural behaviour of three-pile caps subjected to axial compressive loading

This work presents a comparative analysis about the behaviour of pile caps supported by 3 piles subjected to axial loading. Piles with 20 cm and 30 cm diameters were analysed. The main reinforcement was maintained in all the specimens, however, the arrangement of the secondary reinforcement varied. The main reinforcement consisted of steel bars connecting the piles. The secondary reinforcement was made up of: (a) bars going through the piles and through the projection of the column, (b) bars forming a network, and (c) vertical and horizontal stirrups. The main objective was the observation of the pile cap behaviour regarding the cracks and the modes of rupture. The real scale specimens were subjected to experimental tests until failure by rupture. Instruments were placed with the aim to obtain the displacement of the bases, the strains in the main and secondary reinforcement bars, in the compression struts, in the lower and upper nodal zones and in the sides of the caps. None of the caps reached failure by rupture with a load less than 1.12 times the theoretical load. The specimens ruptured due to the cracking of the compression strut and/or the yielding of the reinforcement bars in one direction.

Experiments on stress-triaxiality dependence of material behavior of aluminum alloys

The paper presents and discusses experimental procedures, visual observations and test results considered important to obtain data that can be used in validation of constitutive relations and failure criteria. The aim is to investigate the combined effects of stress intensity, stress-triaxiality and Lode parameter on the material response and failure behavior of aluminum alloys. Smooth and pre-notched tensile and shear specimens were manufactured from both very thin sheets and thicker plates to cover a wide range of stress triaxialities and Lode parameters. In addition, modified Arcan specimens were designed allowing investigation of the effect of sudden changes in stress states and deformation modes on the material behavior. (C) 2009 Elsevier Ltd. All rights reserved.

Infinite horizon MPC with non-minimal state space feedback

In the MPC literature, stability is usually assured under the assumption that the state is measured. Since the closed-loop system may be nonlinear because of the constraints, it is not possible to apply the separation principle to prove global stability for the Output feedback case. It is well known that, a nonlinear closed-loop system with the state estimated via an exponentially converging observer combined with a state feedback controller can be unstable even when the controller is stable. One alternative to overcome the state estimation problem is to adopt a non-minimal state space model, in which the states are represented by measured past inputs and outputs [P.C. Young, M.A. Behzadi, C.L. Wang, A. Chotai, Direct digital and adaptative control by input-output, state variable feedback pole assignment, International journal of Control 46 (1987) 1867-1881; C. Wang, P.C. Young, Direct digital control by input-output, state variable feedback: theoretical background, International journal of Control 47 (1988) 97-109]. In this case, no observer is needed since the state variables can be directly measured. However, an important disadvantage of this approach is that the realigned model is not of minimal order, which makes the infinite horizon approach to obtain nominal stability difficult to apply. Here, we propose a method to properly formulate an infinite horizon MPC based on the output-realigned model, which avoids the use of an observer and guarantees the closed loop stability. The simulation results show that, besides providing closed-loop stability for systems with integrating and stable modes, the proposed controller may have a better performance than those MPC controllers that make use of an observer to estimate the current states. (C) 2008 Elsevier Ltd. All rights reserved.

Non-Equilibrium Reaction Rates in the Macroscopic Chemistry Method for DSMC Calculations

The Direct Simulation Monte Carlo (DSMC) method is used to simulate the flow of rarefied gases. In the Macroscopic Chemistry Method (MCM) for DSMC, chemical reaction rates calculated from local macroscopic flow properties are enforced in each cell. Unlike the standard total collision energy (TCE) chemistry model for DSMC, the new method is not restricted to an Arrhenius form of the reaction rate coefficient, nor is it restricted to a collision cross-section which yields a simple power-law viscosity. For reaction rates of interest in aerospace applications, chemically reacting collisions are generally infrequent events and, as such, local equilibrium conditions are established before a significant number of chemical reactions occur. Hence, the reaction rates which have been used in MCM have been calculated from the reaction rate data which are expected to be correct only for conditions of thermal equilibrium. Here we consider artificially high reaction rates so that the fraction of reacting collisions is not small and propose a simple method of estimating the rates of chemical reactions which can be used in the Macroscopic Chemistry Method in both equilibrium and non-equilibrium conditions. Two tests are presented: (1) The dissociation rates under conditions of thermal non-equilibrium are determined from a zero-dimensional Monte-Carlo sampling procedure which simulates ‘intra-modal’ non-equilibrium; that is, equilibrium distributions in each of the translational, rotational and vibrational modes but with different temperatures for each mode; (2) The 2-D hypersonic flow of molecular oxygen over a vertical plate at Mach 30 is calculated. In both cases the new method produces results in close agreement with those given by the standard TCE model in the same highly nonequilibrium conditions. We conclude that the general method of estimating the non-equilibrium reaction rate is a simple means by which information contained within non-equilibrium distribution functions predicted by the DSMC method can be included in the Macroscopic Chemistry Method.

Heroin-assisted treatment as a response to the public health problem of opiate dependence

Injection drug use (involving the injection of illicit opiates) poses serious public health problems in many countries. Research has indicated that injection drug users are at higher risk for morbidity in the form of HIV/AIDS and Hepatitis B and C, and drug-related mortality, as well as increased criminal activity. Methadone maintenance treatment is the most prominent form of pharmacotherapy treatment for illicit opiate dependence in several countries, and its application varies internationally with respect to treatment regulations and delivery modes. In order to effectively treat those patients who have previously been resistant to methadone maintenance treatment, several countries have been studying and/or considering heroin-assisted treatment as a complementary form of opiate pharmacotherapy treatment. This paper provides an overview of the prevalence of injection drug use and the opiate dependence problem internationally, the current opiate dependence treatment landscape in several countries, and the status of ongoing or planned heroin-assisted treatment trials in Australia, Canada and certain European countries.

Sol-gel preparation of near-infrared broadband emitting Er(3+)-doped SiO(2)-Ta(2)O(5) nanocomposite films

This article reports a study on the preparation, densification process, and structural and optical properties of SiO(2)-Ta(2)O(5) nanocomposite films obtained by the sol-gel process. The films were doped with Er(3+) and the Si:Ta molar ratio was 90:10. Values of refractive index, thickness and vibrational modes in terms of the number of layers and thermal annealing time are described for the films. The densification process is accompanied by OH group elimination, increase in the refractive index, and changes in film thickness. Full densification of the film is acquired after 90 min of annealing at 900 degrees C. The onset of crystallization and devitrification, with the growth of Ta(2)O(5) nanocrystals occurs with film densification, evidenced by high-resolution transmission electron microscopy. The Er(3+)-doped nanocomposite annealed at 900 degrees C consists of Ta(2)O(5) nanoparticles, with sizes around 2 nm, dispersed in the SiO(2) amorphous phase. The main emission peak of the film is detected at around 1532 nm, which can be assigned to the (4)I(13/2)->(4)I(15/2) transition of the Er(3+) ions present in the nanocomposites. This band has a full width at half medium of 64 nm, and the lifetime measured for the (4)I(13/2) levels is 5.4 ms, which is broader compared to those of other silicate systems. In conclusion, the films obtained in this work are excellent candidates for use as active planar waveguide. (C) 2010 Elsevier B.V. All rights reserved.

Signature of mott-insulator transition with ultracold fermions in a one-dimensional optical lattice

Using the exact Bethe ansatz solution of the Hubbard model and Luttinger liquid theory, we investigate the density profiles and collective modes of one-dimensional ultracold fermions confined in an optical lattice with a harmonic trapping potential. We determine a generic phase diagram in terms of a characteristic filling factor and a dimensionless coupling constant. The collective oscillations of the atomic mass density, a technique that is commonly used in experiments, provide a signature of the quantum phase transition from the metallic phase to the Mott-insulator phase. A detailed experimental implementation is proposed.

Phase-dependent fluorescence linewidth narrowing in a three-level atom damped by a finite-bandwidth squeezed vacuum

We examine subnatural phase-dependent linewidths in the fluorescence spectrum of a three-level atom damped by a narrow-bandwidth squeezed vacuum in a cavity. Using the dressed-atom model approach of a strongly driven three-level cascade system, we derive the master equation of the system from which we obtain simple analytical expressions for the fluorescence spectrum. We show that the phase effects depend on the bandwidths of the squeezed vacuum and the cavity relative to the Rabi frequency of the driving fields. When the squeezing bandwidth is much larger than the Rabi frequency, the spectrum consists of five lines with only the central and outer sidebands dependent on the phase. For a squeezing bandwidth much smaller than the Rabi frequency the number of lines in the spectrum and their phase properties depend on the frequency at which the squeezing and cavity modes are centered. When the squeezing and cavity modes are centered on the inner Rabi sidebands, the spectrum exhibits five lines that are completely independent of the squeezing phase with only the inner Rabi sidebands dependent on the squeezing correlations. Matching the squeezing and cavity modes to the outer Rabi sidebands leads to the disappearance of the inner Rabi sidebands and a strong phase dependence of the central line and the outer Rabi sidebands. We find that in this case the system behaves as an individual two-level system that reveals exactly the noise distribution in the input squeezed vacuum. [S1050-2947(97)00111-X].

Spondylocostal Dysostosis Associated with Methylmalonic Aciduria

Spondylocostal dysostosis (SCD) is a genetic disorder characterized by vertebral segmentation and formation defects associated with changes of the ribs. Autosomal dominant and recessive modes of inheritance have been reported. Methylmalonic aciduria (MMA) is an inborn error of propionate or cobalamin metabolism. It is an autosomal recessive disorder and one of the most frequent forms of branched-chain organic acidurias. Here we report on a case of a Brazilian boy with both diseases. As we know, it is the first case in the literature with the occurrence of both SCD and MMA-the first a skeletal disease and the latter an inborn error of metabolism.

Trigger performance of mid-level ICU mechanical ventilators during assisted ventilation: a bench study

Objective: To compare the triggering performance of mid-level ICU mechanical ventilators with a standard ICU mechanical ventilator. Design: Experimental bench study. Setting: The respiratory care laboratory of a university-affiliated teaching hospital. Subject: A computerized mechanical lung model, the IngMar ASL5000. Interventions: Ten mid-level ICU ventilators were compared to an ICU ventilator at two levels of lung model effort, three combinations of respiratory mechanics (normal, COPD and ARDS) and two modes of ventilation, volume and pressure assist/control. A total of 12 conditions were compared. Measurements and main results: Performance varied widely among ventilators. Mean inspiratory trigger time was < 100 ms for only half of the tested ventilators. The mean inspiratory delay time (time from initiation of the breath to return of airway pressure to baseline) was longer than that for the ICU ventilator for all tested ventilators except one. The pressure drop during triggering (Ptrig) was comparable with that of the ICU ventilator for only two ventilators. Expiratory Settling Time (time for pressure to return to baseline) had the greatest variability among ventilators. Conclusions: Triggering differences among these mid-level ICU ventilators and with the ICU ventilator were identified. Some of these ventilators had a much poorer triggering response with high inspiratory effort than the ICU ventilator. These ventilators do not perform as well as ICU ventilators in patients with high ventilatory demand.

Cervical Mobility in Women With Migraine

Objective.-To contrast the cervical range of motion (CROM) in women with episodic migraine (EM), transformed migraine (TM), and controls without migraine headaches. Background.-Migraineurs often complain about neck pain. Furthermore, neck problems can worsen the headaches in individuals with migraine. Individuals with neck pain usually have reduced CROM. Nonetheless, studies assessing the CROM in migraineurs are scarce. Methods.-Our sample was selected in an outpatient headache clinic, and consisted of 45 women aged 20-54 years old, 15 per group. Cervical mobility was evaluated in movements of flexion, extension, right lateral flexion, left lateral flexion, right rotation, and left rotation using the CROM technique, and was contrasted among the groups. Migraine clinical patterns were also evaluated ( frequency, duration of migraine, pain in the moment of evaluation, pain in movement, and pain localization) as a function of CROM. Results.-Compared with controls, individuals with TM had numerically inferior CROM in all parameters, and significant reduction in 3 of them: extension (59.3 vs 68.1, P = .02), left lateral flexion (44.5 vs 49.1, P = .03), and right rotation (62.2 vs 69.6, P = .02). Compared with individuals with migraine, the TM group presented significantly reduced mobility only for extension ( 59.3 vs 68.4, P = .02). Migraineurs also had numerically inferior ROM, contrasted to controls, in 5 of the 6 parameters, although significance was seen just for right rotation (60.8 vs 68.6 P < .01). There was no correlation between cervical mobility and migraine parameters. The CROM was not reduced for the symptomatic side of migraine, in cases of unilateral pain. Conclusion.-Contrasted to controls, individuals with episodic and TM have decreased cervical range of motion.

Effect of framework design on crown failure

This study evaluated the effect of core-design modification on the characteristic strength and failure modes of glass-infiltrated alumina (In-Ceram) (ICA) compared with porcelain fused to metal (PFM). Premolar crowns of a standard design (PFMs and ICAs) or with a modified framework design (PFMm and ICAm) were fabricated, cemented on dies, and loaded until failure. The crowns were loaded at 0.5 mm min(-1) using a 6.25 mm tungsten-carbide ball at the central fossa. Fracture load values were recorded and fracture analysis of representative samples were evaluated using scanning electron microscopy. Probability Weibull curves with two-sided 90% confidence limits were calculated for each group and a contour plot of the characteristic strength was obtained. Design modification showed an increase in the characteristic strength of the PFMm and ICAm groups, with PFM groups showing higher characteristic strength than ICA groups. The PFMm group showed the highest characteristic strength among all groups. Fracture modes of PFMs and of PFMm frequently reached the core interface at the lingual cusp, whereas ICA exhibited bulk fracture through the alumina core. Core-design modification significantly improved the characteristic strength for PFM and for ICA. The PFM groups demonstrated higher characteristic strength than both ICA groups combined.

Bond Strength of Fiber Posts to Weakened Roots After Resin Restoration With Different Light-Curing Times

Introduction: This study evaluated the bond strength of translucent fiber posts to experimentally weakened radicular dentin restored with composite resin and polymerized with different light-exposure time. Methods: Roots of 60 maxillary incisors were used. Twenty-four hours after obturation, the filling materials of root canals were removed to a depth of 12 mm, and 4 groups were randomly formed. In 3 groups, root dentin was flared to produce a space between fiber post and canal walls. In the control group, the roots were not experimentally weakened. The flared roots were bulk restored with composite resin, which was light-activated through the translucent post for 40, 80, or 120 seconds. Posts were cemented, and after 24 hours, all roots were sectioned transversely in the coronal, middle, and apical regions, producing 1-mm-thick slices. Push-out test was performed, and failure modes were observed. Results The quantitative analysis showed significant statistical difference only among groups (P <.001). Comparing the weakened/restored groups, composite light-exposure time did not influence the results. Overall, adhesive failures occurred more frequently than other types of failures. Cohesive failures occurred only in the weakened/restored roots. Conclusions Intracanal root restoration with composite resin and translucent fiber posts provided similar or higher bond strength to dentin than the control group, regardless of the light-exposure time used for polymerization. (J Endod 2009;35:1034-1039)

Dual mode cooling house in the warm humid tropics

Passive techniques as an alternative to artificial cooling can bring important energy, environmental, financial, operational and qualitative benefits. However, regions such as the wet tropics can reach high levels of thermal stress in which passive means alone are unable to provide appropriate thermal comfort standards for some parts of the year. Despite a great accumulation of empirical information on the passive performance of houses for either free-running or conditioned modes, very little work has been done on the thermal performance of buildings that can operate with a mixed-running strategy in warm-humid climates. Buildings with such design features are able to balance the needs for comfort, privacy, and energy efficiency during different periods of the year. As free-running and conditioned modes are believed by many to be 'opposite' approaches, and have been presented as separate strategies, this paper demonstrates that not all parameters are directly opposite and a possible dual-mode integrated operation can be used for warm-humid locations for maximum comfort and minimum energy requirements. For this purpose, simulation runs using ESP-R (University of Strathclyde, ESRU, UK) were based on the climate data of Darwin (Australia) and on the ventilation styles of the house: free running and conditioned. Design features applicable to both, i.e. for a dual mode operation could be identified and the differences between conditioned and free running were demonstrated and proved not to be totally conflicting and therefore suitable for a dual mode operation. Different daily usage profiles (five use patterns were defined), and zoning of sleeping and living areas are presented. The dual mode use patterns compared to the base case house, for all the user possibilities, had improved performances of 17-52%, when compared to the free-running mode and 66-98% when compared to the conditioned mode. Simulation runs using other warm-humid climates (Miami, USA; Sao Luis, Brazil; Kuala Lumpur, Malaysia) were also conducted and compared to the results found for Darwin. (C) 2002 Elsevier Science Ltd. All rights reserved.

Cartografando movimentos curriculares produzidos nas redes de conversações nos encontrosformações do PROEJA/IFES/ES

Problematiza a constituição do currículo (e da “formação docente” no campo curricular), no cotidiano escolar, na dimensão das conversações. Objetiva acompanhar os movimentos curriculares concernentes ao Proeja entre formas e forças complexas no cotidiano do Ifes – campus Venda Nova do Imigrante (VNI). Compõe com as linhas de pensamentos principalmente de Alves (2008, 2010, 2012); Carvalho (2004, 2008a, 2008b, 2009, 2012); Deleuze (1988, 2002, 2010); Deleuze e Guattari (1995); Ferraço (2007, 2008a, 2008b); Garcia (2011); Guattari (1987, 2004, 2012); Kastrup (2009, 2013); Lopes e Macedo (2011); Lopes (2010, 2011); Oliveira (2005, 2009, 2012); Paiva (2004, 2009); Rolnik (1989); e Spinoza (2013), entremeando os conceitos de movimentos e afetos no campo do currículo em redes na relação híbrida com os encontros-formações docente do/no Proeja. Adota a (não) metodologia cartográfica ao acompanhar movimentos curriculares (des)(re)territorializantes nas redes de conversações, especialmente nos encontrosformações: “Rodas de conversas com professores e demais servidores do Proeja”. Utiliza como principais instrumentos metodológicos a observação participante, a gravação das vozes e o registro em diário de campo. Contribui para outros movimentos de pesquisa ao capturar produzir e analisar dados em que se percebe que: ainda que tenha ocorrido um planejamento coletivo, outras temáticas surgiram nos encontros formações (que não se pretendiam engessados e não objetivavam a paralisação dos fluxos que pedem passagem), e tais assuntos puderam ser usados como disparadores para criação de outros movimentos curriculares; as concepções dos professores sobre a “dificuldade/facilidade” em ministrar aulas para o Proeja e os lugares estabelecidos entre estudantes e docentes no processo ensino-aprendizagem não estão relacionados diretamente, em relação de causa e efeito, à disciplina/área de conhecimento específica que ministram, mas aos agenciamentos, aos ligamentos e às rupturas produzidas nas relações com essas redes de saberes fazeres poderes que envolvem múltiplos agentes: docentes, outros servidores, alunos, experiências e encontros múltiplos dentro fora no espaço tempo do Ifes; uma tríade-refrão coopera para a criação de uma fôrma triangular que enfatiza a noção de um padrão em um processo molar enraizado nas árvores do conhecimento: perfil, seleção e nivelamento, contudo, algumas linhas de fuga dissonantes são criadas por entre as fissuras dos pretensos tons harmônicos; as frases “os professores do IF não estão preparados para ministrar aulas para o Proeja” ou “não há formação/qualificação para os docentes se relacionarem com o Proeja” são utilizadas, em alguns discursos, como escudos-argumentos para a opção-política de não oferta de vagas para a modalidade EJA em composição com fios que afirmam tal especificidade da educação básica, dentro da rede federal, como um “favor social”; processos que envolvem a (des)organização da matriz curricular são considerados por alguns participantes como início, “produto” e objetivo das conversas curriculares e provocam tensões que (i)mobilizam, (não) movimentam entre os afetos dos corpos, podendo levar à (não) ação coletiva; a noção de “mercado de trabalho” ainda impera nos discursos, ciclicamente, enquanto início fim das problematizações do currículo do Ensino Médio e da EJA; a expressão “integração curricular” é constantemente usada nos discursos que circulam o campus, no entanto, os sentidos produzidos, as concepções e as teorias curriculares que embasam a noção de “integração” no currículo são bem diversos; não há totalidades nos discursos, não há homogeneização, não foi efetivada nenhuma coesão/única voz representante (e esse também não era o objetivo desta pesquisa); ainda que o tema da roda se propusesse às conversas curriculares do/no Proeja, nesses encontros, os participantes manifestaram a necessidade de intensificar os movimentos produzidos nas rodas visando à discussão dos currículos textos de todos os cursos e modalidades ofertados pelos campus VNI e na intensificação de espaços para trocas de experiências curriculares cotidianas; na potencialização das diferenças como possibilidades de inventividade nos encontros-formações docente e nas danças curriculares que envolvem diversas relações de aprendizagem no Ifes, algumas experimentações foram produzidas, entre afetos, criando composições(des)(re)territorializantes e ressonando com movimentos que não se restringiram às rodas de conversas, contudo, enredaram-se em fios de outros espaços tempos do campus em tentativas de propagações de currículos multidão.