Applications of accurate, high-precision Pb isotope ratio measurement by multi-collector ICP-MS

The isotope composition of Ph is difficult to determine accurately due to the lack of a stable normalisation ratio. Double and triple-spike addition techniques provide one solution and presently yield the most accurate measurements. A number of recent studies have claimed that improved accuracy and precision could also be achieved by multi-collector ICP-MS (MC-ICP-MS) Pb-isotope analysis using the addition of Tl of known isotope composition to Pb samples. In this paper, we verify whether the known isotope composition of Tl can be used for correction of mass discrimination of Pb with an extensive dataset for the NIST standard SRM 981, comparison of MC-ICP-MS with TIMS data, and comparison with three isochrons from different geological environments. When all our NIST SRM 981 data are normalised with one constant Tl-205/Tl-203 of 2.38869, the following averages and reproducibilities were obtained: Pb-207/Pb-206=0.91461+/-18; Pb-208/Ph-206 = 2.1674+/-7; and (PbPh)-Pb-206-Ph-204 = 16.941+/-6. These two sigma standard deviations of the mean correspond to 149, 330, and 374 ppm, respectively. Accuracies relative to triple-spike values are 149, 157, and 52 ppm, respectively, and thus well within uncertainties. The largest component of the uncertainties stems from the Ph data alone and is not caused by differential mass discrimination behaviour of Ph and Tl. In routine operation, variation of sample introduction memory and production of isobaric molecular interferences in the spectrometer's collision cell currently appear to be the ultimate limitation to better reproducibility. Comparative study of five different datasets from actual samples (bullets, international rock standards, carbonates, metamorphic minerals, and sulphide minerals) demonstrates that in most cases geological scatter of the sample exceeds the achieved analytical reproducibility. We observe good agreement between TIMS and MC-ICP-MS data for international rock standards but find that such comparison does not constitute the ultimate. test for the validity of the MC-ICP-MS technique. Two attempted isochrons resulted in geological scatter (in one case small) in excess of analytical reproducibility. However, in one case (leached Great Dyke sulphides) we obtained a true isochron (MSWD = 0.63) age of 2578.3 +/- 0.9 Ma, which is identical to and more precise than a recently published U-Pb zircon age (2579 3 Ma) for a Great Dyke websterite [Earth Planet. Sci. Lett. 180 (2000) 1-12]. Reproducibility of this age by means of an isochron we regard as a robust test of accuracy over a wide dynamic range. We show that reliable and accurate Pb-isotope data can be obtained by careful operation of second-generation MC-ICP magnetic sector mass spectrometers. (C) 2002 Elsevier Science B.V. All rights reserved.

Polyethylene flow prediction with a differential multi-mode Pom-Pom model

We report the first steps of a collaborative project between the University of Queensland, Polyflow, Michelin, SK Chemicals, and RMIT University; on simulation, validation and application of a recently introduced constitutive model designed to describe branched polymers. Whereas much progress has been made on predicting the complex flow behaviour of many - in particular linear - polymers, it sometimes appears difficult to predict simultaneously shear thinning and extensional strain hardening behaviour using traditional constitutive models. Recently a new viscoelastic model based on molecular topology, was proposed by McLeish and Larson (1998). We explore the predictive power of a differential multi-mode version of the pom-pom model for the flow behaviour of two commercial polymer melts: a (long-chain branched) low-density polyethylene (LDPE) and a (linear) high-density polyethylene (HDPE). The model responses are compared to elongational recovery experiments published by Langouche and Debbaut (1999), and start-up of simple shear flow, stress relaxation after simple and reverse step strain experiments carried out in our laboratory.

Parenteral and mucosal delivery of a novel multi-epitope M protein-based group A streptococcal vaccine construct: investigation of immunogenicity in mice

Primary vaccine strategies against group A streptococci (GAS) have focused on the M protein-the target of opsonic antibodies important for protective immunity. We have previously reported protection of mice against GAS infection following parenteral delivery of a multi-epitope vaccine construct, referred to as a heteropolymer. This current report has assessed mucosal (intranasal (i.n.) and oral) delivery of the heteropolymer in mice with regard to the induction and specificity of mucosal and systemic antibody responses, and compared this to parenteral delivery. GAS-specific IgA responses were detected in saliva and gut upon i.n. and oral delivery of the heteropolymer co-administered with cholera toxin B subunit, respectively. High titre serum IgG responses were elicited to the heteropolymer following all routes of delivery when administered with adjuvant. Moreover, as with parenteral delivery, serum IgG antibodies were detected to the individual heteropolymer peptides following i.n. but not oral delivery. These data support the potential of the i.n. route in the mucosal delivery of a GAS vaccine. (C) 2002 Elsevier Science Ltd. All rights reserved.

Exotic vs endemic biocontrol agents: Would the real stratiolaelaps miles (Berlese) (Acari : Mesostigmata : Laelapidae), please stand up?

The ability of introduced organisms to invade undisturbed native habitats is a major concern in conservation biology and has resulted in a re-evaluation of the introduction of exotic biocontrol agents, especially of generalist predators. One such agent is Stratiolaelaps miles (Berlese), a predatory mite described from Italy, known from throughout the Holarctic, and apparently accidentally introduced to other areas of the world, including Australia. Initial investigations revealed that putative S. miles could be found in both disturbed and relatively pristine habitats in Queensland, Australia. However, analysis of the mitochondrial DNA of five populations showed most to be highly divergent genetically. Subsequent morphological analysis established two species groups: the lamington-group from cool-temperate to subtropical rainforests in Eastern Australia and the more eurytopic miles-group with a cosmopolitan distribution. We describe two new species from each of these complexes (Stratiolaelaps womersleyi, Stratiolaelaps lamington; Stratiolaelaps marilyn, Stratiolaelaps lorna, respectively), and resurrect Stratiolaelaps scimitus (Womersley), a species which often appears to have been confused with S. miles. Additionally, the large genetic distances among morphologically homogenous species in the miles-group suggest that the apparently cosmopolitan S. miles may be composed of a suite of cryptic species of potentially varying utility in biological control. (C) 2002 Elsevier Science (USA). All rights reserved.

Evaluation of potential biocontrol agents against Claviceps africana in vitro and in vivo

Undiluted culture filtrates of two commercial products of Trichoderma spp., Trichopel and Trichoflow, and two isolates of Penicillium citrinum completely inhibited the conidial germination of macroconidia of Claviceps africana , the cause of ergot or sugary disease of sorghum (Sorghum bicolor) in vitro . Similarly, Pseudomonas aeruginosa and Burkholderia cepacia completely inhibited macroconidial germination, with the former being more effective at high dilutions. In contrast, these bacterial isolates failed to inhibit infection in vivo in glasshouse tests with ergot-inoculated sorghum, but all fungal biocontrol agents (including an isolate of Epicoccum nigrum) reduced the severity of disease (percentage of infected spikelets per panicle), in some cases completely inhibiting the development of ergot. In a second glasshouse trial, optimum control was achieved when the biocontrol agents were applied 3-7 days before inoculation with conidia of C. africana .

Initiation of biological agents in patients with ankylosing spondylitis: results of a Delphi study by the ASAS Group

Background: There is ample evidence of important symptomatic efficacy of tumour necrosis factor alpha (TNFalpha) inhibition in ankylosing spondylitis (AS). Moreover, studies suggest that anti-TNF could be considered as the first disease controlling antirheumatic treatment (DC-ART) for AS. Objective: To determine precisely which patients with AS are most likely to benefit from anti-TNFalpha treatment because of the cost and possible long term side effects of such treatment. Methods: Assessment in Ankylosing Spondylitis (ASAS) members were asked to use a Delphi technique to name the characteristics of patients with AS for whom they would start DC-ART, in three different clinical presentations (isolated axial involvement, peripheral arthritis, enthesitis). Results: Among the 62 invited ASAS members, more than 50% actively participated in the four phases of definition according to the Delphi technique. For each of the three clinical presentations, a combination of five to six domains was proposed, with an evaluation instrument and a cut off point defining a minimum level of activity for each domain. Conclusion: This study provides a profile for a patient with AS for considering initiation of biological agents that reflects the opinion of the ASAS members, using a Delphi exercise. Further studies are required to assess their relevance and their consistency with clinical practice.

Selecting methods to solve multi-well master equations

There are several competing methods commonly used to solve energy grained master equations describing gas-phase reactive systems. When it comes to selecting an appropriate method for any particular problem, there is little guidance in the literature. In this paper we directly compare several variants of spectral and numerical integration methods from the point of view of computer time required to calculate the solution and the range of temperature and pressure conditions under which the methods are successful. The test case used in the comparison is an important reaction in combustion chemistry and incorporates reversible and irreversible bimolecular reaction steps as well as isomerizations between multiple unimolecular species. While the numerical integration of the ODE with a stiff ODE integrator is not the fastest method overall, it is the fastest method applicable to all conditions.

Actively shielded multi-layer gradient coil designs with improved cooling properties

In standard cylindrical gradient coils consisting of a single layer of wires, a limiting factor in achieving very large magnetic field gradients is the rapid increase in coil resistance with efficiency. This is a particular problem in small-bore scanners, such as those used for MR microscopy. By adopting a multi-layer design in which the coil wires are allowed to spread out into multiple layers wound at increasing radii, a more favourable scaling of resistance with efficiency is achieved, thus allowing the design of more powerful gradient coils with acceptable resistance values. Previously this approach has been applied to the design of unshielded, longitudinal, and transverse gradient coils. Here, the multi-layer approach has been extended to allow the design of actively shielded multi-layer gradient coils, and also to produce coils exhibiting enhanced cooling characteristics. An iterative approach to modelling the steady-state temperature distribution within the coil has also been developed. Results indicate that a good level of screening can be achieved in multi-layer coils, that small versions of such coils can yield higher efficiencies at fixed resistance than conventional two-layer (primary and screen) coils, and that performance improves as the number of layers of increases. Simulations show that by optimising multi-layer coils for cooling it is possible to achieve significantly higher gradient strengths at a fixed maximum operating temperature. A four-layer coil of 8 mm inner diameter has been constructed and used to test the steady-state temperature model. (C) 2003 Elsevier Inc. All rights reserved.

Plano de implementa????o do projeto de desenvolvimento de capacidade de governan??a

Desde a d??cada de 1990, o Governo Federal brasileiro vem implementando uma agenda ambiciosa de reformas do Estado, centradas na redu????o da pobreza e na melhoria da efici??ncia dos servi??os p??blicos. As principais prioridades, conforme previstas no Plano Plurianual (PPA) para o per??odo 2003-2007, s??o as seguintes: inclus??o social e redu????o da desigualdade; crescimento econ??mico com gera????o de emprego; distribui????o de renda e respeito ao meio ambiente; promo????o e amplia????o dos direitos de cidadania; e fortalecimento da democracia. No in??cio de 2006, o Governo criou a Pol??tica Nacional de Desenvolvimento de Pessoal (Decreto 5.707), com o objetivo de melhorar e aumentar a efici??ncia e a efic??cia na presta????o de servi??os p??blicos. No marco dessa pol??tica recente, as escolas de administra????o p??blica desempenham um papel fundamental na identifica????o das compet??ncias que precisam ser desenvolvidas nas institui????es do governo, bem como na implementa????o de pol??ticas de capacita????o para os servidores p??blicos, diretamente e/ou em parceria com escolas de governo nos n??veis federal, estadual ou local. O Canad?? tamb??m est?? criando uma estrutura para levantar as compet??ncias necess??rias para os servidores p??blicos e desenvolv??-las como um componente da Renova????o do Servi??o P??blico em todo o governo. Como institui????es l??deres no desenvolvimento de compet??ncias de servidores p??blicos, a Canada School of Public Service (CSPS) e a Escola Nacional de Administra????o P??blica (ENAP) firmaram uma parceria para implementar o Projeto de Desenvolvimento de Capacidade de Governan??a no Brasil. A finalidade do Projeto ?? melhorar a capacidade de servidores p??blicos federais, estaduais e municipais do Brasil para desenvolver e implementar programas de capacita????o e gerenciar pol??ticas p??blicas descentralizadas. Espera-se que essa parceria e o resultante compartilhamento de experi??ncias em capacita????o para governan??a efetiva contribuam para a redu????o da pobreza e das desigualdades no Brasil, por meio do desenvolvimento de compet??ncias de servidores na presta????o de servi??os p??blicos eficazes e eficientes, voltados para o cidad??o. O Projeto re??ne, al??m das duas principais Escolas de Governo no Canad?? e no Brasil, seis Escolas Brasileiras de Administra????o P??blica regionais e duas renomadas Institui????es Acad??micas Canadenses ??? a Queen???s University e a Western Ontario University. O Minist??rio do Desenvolvimento Social e Combate ?? Fome (MDS) e tr??s Secretarias Especiais do Governo Federal ??? Ra??a (SEPPIR), Direitos Humanos (SEDH) e Pol??ticas para as Mulheres (SPM) ??? tamb??m se envolver??o nas atividades de compartilhamento de conhecimentos com o Human Resources and Skills Development Canada (HRSDC) e a Canada Public Service Agency (CPSA). A CIDA fornecer?? CND$1.700.000 por meio do Programa Brasil-Canad?? de Interc??mbio de Conhecimentos para a Promo????o da Equidade (PIPE). A contribui????o da ENAP ser?? de CND$1.069.707 em esp??cie. A CSPS contribuir?? com cursos, al??m de conhecimentos e suporte t??cnicos, avaliados em CND$1.000.000. Aproveitando a parceria entre a CSPS e a ENAP, que resultou na transfer??ncia e na adapta????o bem sucedidas de cursos e metodologias canadenses, o novo projeto extrapola o n??cleo do servi??o p??blico em Bras??lia, alcan??ando escolas de governo em regi??es brasileiras em situa????o de desvantagem. ?? semelhan??a do papel da CSPS no primeiro projeto, a ENAP fortalecer?? a capacidade das escolas parceiras regionais para capacitar servidores p??blicos envolvidos na presta????o de servi??os aos brasileiros. O interc??mbio estruturado entre Minist??rios dos Governos canadense e brasileiro tamb??m aplicar?? a aprendizagem mais diretamente a quest??es de pol??ticas e programas sociais do Brasil. O desafio assumido neste Projeto ?? a adapta????o de conhecimentos e aprendizagem, com vistas a melhorar a implementa????o de pol??ticas e programas sociais. Para tanto, a CSPS e a ENAP introduzir??o novos cursos nos curr??culos das escolas parceiras e incorporar??o novos m??todos e tecnologias de aprendizagem como, por exemplo, comunidades de pr??tica virtuais e um componente de tutoria (mentoring) envolvendo o Human Resources and Skills Development Canada e o Minist??rio do Desenvolvimento Social e Combate ?? Fome do Brasil. Seis institui????es da Rede Nacional de Escolas de Governo do Brasil e do Programa de Parceria da ENAP foram selecionadas e convidadas a se unir ?? CSPS e ?? ENAP nesse novo Projeto: a Universidade Federal do Par?? (UFPA), de Bel??m (estado do Par?? ??? regi??o Norte); a Funda????o Joaquim Nabuco (FUNDAJ), de Recife (Pernambuco ??? Nordeste); a Universidade Corporativa do Servi??o P??blico / Secretaria de Administra????o do Estado da Bahia (UCS/SAEB), Salvador (Bahia ??? Nordeste); a Escola de Governo do Mato Grosso do Sul (ESCOLAGOV), Campo Grande (estado do Mato Grosso do Sul ??? Centro-Oeste); a Escola Nacional de Ci??ncias Estat??sticas / Instituto Brasileiro de Geografia e Estat??stica (ENCE/IBGE), Rio de Janeiro (estado do Rio de Janeiro ??? Sudeste); e o Instituto Municipal de Administra????o P??blica (IMAP) de Curitiba (Paran?? ??? Sul). Essas escolas de refer??ncia foram escolhidas segundo sua capacidade de trabalhar como p??los de pr??ticas inovadoras em pol??ticas p??blicas e disseminar os benef??cios do Projeto para outras escolas em suas regi??es, por meio da Rede Nacional coordenada pela ENAP. O objetivo dessa parceria ?? fortalecer as escolas de governo locais, para que estas desenvolvam, por meio de eventos de aprendizagem, compet??ncias em servidores p??blicos, a fim de aumentar a capacidade do governo na implementa????o e gest??o de pol??ticas p??blicas. O Plano de Implementa????o do Projeto (PIP) descreve o trabalho a ser realizado por essas institui????es nos pr??ximos 30 meses, ao tempo em que serve de guia para os Parceiros do Projeto no que se refere ??s a????es e aos recursos necess??rios para a obten????o dos resultados acordados. Na medida em que o Projeto estiver em andamento e os parceiros iniciarem um interc??mbio produtivo de conhecimentos, o Plano de Trabalho Anual ser?? atualizado e revisto por meio de reuni??es anuais de avalia????o e encontros do Comit?? Diretor do Projeto, com vistas a assegurar que os resultados descritos no PIP sejam alcan??ados com sucesso

Caracterização molecular, formação de biofilme e susceptibilidade a antimicrobianos de isolados de E. coli de aderência difusa Afa/Dr e não Afa/Dr

A Escherichia coli de aderência difusa (DAEC), um patotipo diarreiogênico de E. coli, corresponde a um grupo heterogêneo sem marcador de virulência comum a todos os isolados e de papel controverso na diarreia infantil. O objetivo deste estudo foi caracterizar genotipica e fenotipicamente amostras de DAEC, portadoras e não portadoras de adesinas Afa/Dr, isoladas de crianças com e sem diarreia. Em 70 amostras de DAEC, PCR foi realizado para pesquisa de genes descritos em DAEC, EAEC ou UPEC, que codificam: (i) oito adesinas fimbriais e afimbriais (fimH, papC, sfa, aggA, aafA, agg3A, aidA/aah, afaC); (ii) cinco toxinas (pet, astA, set1A, sat, hlyA); (iii) três proteínas captadoras/receptora de ferro (irp2, iucA, chuA/shuA); (iv) invasina (daaD) e; antígeno 43 (agn43). Ensaio de formação de biofilme foi realizado a partir da bactéria cultivada em caldo Luria-Bertani e inoculada em placas de poliestireno com DMEM suplementado com 0,4% glicose. A leitura da densidade ótica (DO490) foi realizada após coloração com safranina. Soroaglutinação para 23 antígenos O (Probac do Brasil) foi realizada em 50% das DAEC. Método de difusão de disco foi realizado para testar a suscetibilidade a 13 antimicrobianos. A presença de pelo menos um gene que codifica adesinas, toxinas, proteínas captadoras/receptora de ferro, invasina ou antígeno 43 foram encontrados em 58,6%, 51,4%, 80%, 48,6% e 57,1%, respectivamente, com os genes fimH, irp2, agn43, iucA, chuA/shuA, presentes em mais de 50% das amostras. Gene afaC+ (PCR) e/ou sonda afaBC+ (hibridização de colônias) classificou 50% das DAEC como Afa/Dr, sendo pet, sat, irp2, iucA, chuA/shuA e agn43 significantes nessas amostras (p<0,05). Do total das DAEC, 44,3% foram formadoras de biofilme, igualmente distribuídas entre as Afa/Dr e não Afa/Dr, e nenhum gene foi associado com esse fenótipo. Sorologia de 35 amostras evidenciou os seguintes sorogrupos: 1 O29, 2 O125, 2 O127 e 7 O86. Todas as O86 foram de DAEC Afa/Dr. Maiores frequências de resistência antimicrobiana foram encontradas para ampicilina (55,7%), sulfametoxazol/trimetoprim (35,7%) e tetraciclina (28,6%) e o perfil resistente/intermediário para amoxicilina/ácido clavulânico, ampicilina, sulfametoxazol/trimetoprim foi significante nas DAEC Afa/Dr, assim como a multi-droga resistência (p<0,05). Em conclusão, observou-se: (i) alta frequência de fimH e pet e presença de agn43, até então não descrito em DAEC, em frequências similares àquelas encontradas em EAEC, UPEC e EAEC/UPEC, respectivamente; (ii) que as amostras de DAEC Afa/Dr e não Afa/Dr constituíram grupos com perfis genéticos diferenciados entre si; (iii) poucos sorogrupos foram encontrados entre as DAEC; (iv) frequências de resistência menores quando comparado com as poucas descrições em DAEC, sugerindo uma menor pressão seletiva da população do presente estudo e; (v) amostras de DAEC Afa/Dr podem representar um importante reservatório de genes de resistência a antimicrobianos, além de diversos fatores de virulência.