Cr2O3 thin films grown at room temperature by low pressure laser chemical vapour deposition

Chromia (Cr2O3) has been extensively explored for the purpose of developing widespread industrial applications, owing to the convergence of a variety of mechanical, physical and chemical properties in one single oxide material. Various methods have been used for large area synthesis of Cr2O3 films. However, for selective area growth and growth on thermally sensitive materials, laser-assisted chemical vapour deposition (LCVD) can be applied advantageously. Here we report on the growth of single layers of pure Cr2O3 onto sapphire substrates at room temperature by low pressure photolytic LCVD, using UV laser radiation and Cr(CO)(6) as chromium precursor. The feasibility of the LCVD technique to access selective area deposition of chromia thin films is demonstrated. Best results were obtained for a laser fluence of 120 mJ cm(-2) and a partial pressure ratio of O-2 to Cr(CO)(6) of 1.0. Samples grown with these experimental parameters are polycrystalline and their microstructure is characterised by a high density of particles whose size follows a lognormal distribution. Deposition rates of 0.1 nm s(-1) and mean particle sizes of 1.85 mu m were measured for these films. (C) 2011 Elsevier B.V. All rights reserved.

Flow amperometric determination of carbofuran and fenobucarb

A simple, rapid, and precise amperometric method for quantification of N-methylcarbamate pesticides in water samples and phytopharmaceuticals is presented. Carbofuran and fenobucarb are the target analytes. The method is developed in flow conditions providing the anodic oxidation of phenolic-based compounds formed after alkaline hydrolysis. Optimization of instrumental and chemical variables is presented. Under the optimal conditions, the amperometric signal is linear for carbofuran and fenobucarb concentrations over the range of 1.0*10-7 to 1.0*10-5 molL-1, with a detection limit of about 2 ngmL-1. The amperometric method is successfully applied to the analysis of spiked environmental waters and commercial formulations. The proposed method allows 90 samples to be analysed per hour, using 500 mL of sample, and producing wastewaters of low toxicity. The proposed method permits determinations at the mgL 1 level and offers advantages of simplicity, accuracy, precision, and applicability to coloured and turbid samples, and automation feasibility.

Taxonomy of fundamental concepts of localization in cyber-physical and sensor networks

Localization is a fundamental task in Cyber-Physical Systems (CPS), where data is tightly coupled with the environment and the location where it is generated. The research literature on localization has reached a critical mass, and several surveys have also emerged. This review paper contributes on the state-of-the-art with the proposal of a new and holistic taxonomy of the fundamental concepts of localization in CPS, based on a comprehensive analysis of previous research works and surveys. The main objective is to pave the way towards a deep understanding of the main localization techniques, and unify their descriptions. Furthermore, this review paper provides a complete overview on the most relevant localization and geolocation techniques. Also, we present the most important metrics for measuring the accuracy of localization approaches, which is meant to be the gap between the real location and its estimate. Finally, we present open issues and research challenges pertaining to localization. We believe that this review paper will represent an important and complete reference of localization techniques in CPS for researchers and practitioners and will provide them with an added value as compared to previous surveys.

Microstructure, mechanical properties and chemical degradation of brazed AISI 316 stainless steel/alumina systems

The main aims of the present study are simultaneously to relate the brazing parameters with: (i) the correspondent interfacial microstructure, (ii) the resultant mechanical properties and (iii) the electrochemical degradation behaviour of AISI 316 stainless steel/alumina brazed joints. Filler metals on such as Ag–26.5Cu–3Ti and Ag–34.5Cu–1.5Ti were used to produce the joints. Three different brazing temperatures (850, 900 and 950 °C), keeping a constant holding time of 20 min, were tested. The objective was to understand the influence of the brazing temperature on the final microstructure and properties of the joints. The mechanical properties of the metal/ceramic (M/C) joints were assessed from bond strength tests carried out using a shear solicitation loading scheme. The fracture surfaces were studied both morphologically and structurally using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction analysis (XRD). The degradation behaviour of the M/C joints was assessed by means of electrochemical techniques. It was found that using a Ag–26.5Cu–3Ti brazing alloy and a brazing temperature of 850 °C, produces the best results in terms of bond strength, 234 ± 18 MPa. The mechanical properties obtained could be explained on the basis of the different compounds identified on the fracture surfaces by XRD. On the other hand, the use of the Ag–34.5Cu–1.5Ti brazing alloy and a brazing temperature of 850 °C produces the best results in terms of corrosion rates (lower corrosion current density), 0.76 ± 0.21 μA cm−2. Nevertheless, the joints produced at 850 °C using a Ag–26.5Cu–3Ti brazing alloy present the best compromise between mechanical properties and degradation behaviour, 234 ± 18 MPa and 1.26 ± 0.58 μA cm−2, respectively. The role of Ti diffusion is fundamental in terms of the final value achieved for the M/C bond strength. On the contrary, the Ag and Cu distribution along the brazed interface seem to play the most relevant role in the metal/ceramic joints electrochemical performance.

Development of biocompatible and “smart” porous structures using CO2-assisted processes

Dissertação apresentada para a obtenção do grau de Doutor em Engenharia Química, especialidade Engenharia da Reacção Química, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

Space-time monitoring of prescribed burnt soils performance – an effective tool for forest management

Among the most important measures to prevent wild forest fires is the use of prescribed and controlled burning actions in order to reduce the availability of fuel mass. However, the impact of these activities on soil physical and chemical properties varies according to the type of both soil and vegetation and is not fully understood. Therefore, soil monitoring campaigns are often used to measure these impacts. In this paper we have successfully used three statistical data treatments - the Kolmogorov-Smirnov test followed by the ANOVA and the Kruskall-Wallis tests – to investigate the variability among the soil pH, soil moisture, soil organic matter and soil iron variables for different monitoring times and sampling procedures.

Mechanical performance of concrete made with aggregates from construction and demolition waste recycling plants

This research aims at analysing the mechanical performance of concrete with recycled aggregates (RA) from construction and demolition waste (CDW) from various locations in Portugal. First the characteristics of the various aggregates (natural and recycled) used in the production of concrete were thoroughly analysed. The composition of the RA was determined and several physical and chemical tests of the aggregates were performed. In order to evaluate the mechanical performance of concrete, compressive strength (in cubes and cylinders), splitting tensile strength, modulus of elasticity and abrasion resistance tests were performed. Concrete mixes with RA from CDW from several recycling plants were evaluated, in order to understand the influence that the RA's collection point, and consequently their composition, has on the characteristics of the mixes produced. The analysis of the mechanical performance allowed concluding that the use of RA worsens most of the properties tested, especially when fine RA are used. On the other hand, there was an increase in abrasion resistance when coarse RA were used. In global terms, the use of this type of aggregates, in limited contents, is viable from a mechanical viewpoint. (C) 2015 Elsevier Ltd. All rights reserved.

Seroepidemiology and occupational and environmental variables for leptospirosis, brucellosis and toxoplasmosis in slaughterhouse workers in the Paraná State, Brazil

Leptospirosis, brucellosis and toxoplasmosis are widely-distributed zoonosis, being the man an accidental participant of their epidemiological chains. The aim of this paper was to make a seroepidemiological report and identify occupational and environmental variables related to these illnesses in 150 workers in a slaughterhouse in the Northern region of Paraná. For the diagnosis of leptospirosis a microscopical seroagglutination test was applied; for brucellosis, the tamponated acidified antigen test and the 2-mercaptoetanol tests were used, and for toxoplasmosis the indirect immunofluorescence reaction test. For each employee an epidemiological survey was filled, which investigated occupational and environmental variables which could be associated with these infections. Positive results for leptospirosis were found in 4.00% of the samples, for brucellosis in 0.66% of samples and toxoplasmosis in 70.00%. From the three diseases researched, only the results for leptospirosis suggest occupational infection.

Effects of Exercise on Physical and Mental Health, and Cognitive and Brain Functions in Schizophrenia: Clinical and Experimental Evidence

Exercise promotes several health benefits, such as cardiovascular, musculoskeletal and cardiorespiratory improvements. It is believed that the practice of exercise in individuals with psychiatric disorders, e.g. schizophrenia, can cause significant changes. Schizophrenic patients have problematic lifestyle habits compared with general population; this may cause a high mortality rate, mainly caused by cardiovascular and metabolic diseases. Thus, the aim of this study is to investigate changes in physical and mental health, cognitive and brain functioning due to the practice of exercise in patients with schizophrenia. Although still little is known about the benefits of exercise on mental health, cognitive and brain functioning of schizophrenic patients, exercise training has been shown to be a beneficial intervention in the control and reduction of disease severity. Type of training, form of execution, duration and intensity need to be better studied as the effects on physical and mental health, cognition and brain activity depend exclusively of interconnected factors, such as the combination of exercise and medication. However, one should understand that exercise is not only an effective nondrug alternative, but also acts as a supporting linking up interventions to promote improvements in process performance optimization. In general, the positive effects on mental health, cognition and brain activity as a result of an exercise program are quite evident. Few studies have been published correlating effects of exercise in patients with schizophrenia, but there is increasing evidence that positive and negative symptoms can be improved. Therefore, it is important that further studies be undertaken to expand the knowledge of physical exercise on mental health in people with schizophrenia, as well as its dose-response and the most effective type of exercise.

New natural hydraulic lime mortars – Physical and microstructural properties in different curing conditions

Construction and Building Materials 54 (2014) 378–384

Evaluation of mechanical soft-abrasive blasting and chemical cleaning methods on alkyd-paint graffiti made on carbonate stones

In the context of this dissertation several studies were developed resulting in submission and publication “Evaluation of mechanical soft-abrasive blasting and chemical cleaning methods on alkyd-paint graffiti made on calcareous stones” to Journal of Cultural Heritage. (http://dx.doi.org/10.101 /j.culher.2014.10.004)

Mechanism of extracellular silver nanoparticles synthesis by Stereum hirsutum and Fusarium oxysporum

The increasing interest for greener and biological methods of synthesis has led to the development of non-toxic and comparatively more bioactive nanoparticles. Unlike physical and chemical methods of nanoparticle synthesis, microbial synthesis in general and mycosynthesis in particular is cost-effective and environment-friendly. However, different aspects, such as the rate of synthesis, monodispersity and downstream processing, need to be improved. Many fungal-based mechanisms have been proposed for the formation of silver nanoparticles (AgNPs), mainly those involving the presence of nitrate reductase, which has been detected in filtered fungus cell used for AgNPs production. There is a general acceptance that nitrate reductase is the main responsible for the reduction of Ag ions for the formation of AgNPs. However, this generally accepted mechanism for fungal AgNPs production is not totally understood. In order to elucidate the molecules participating in the mechanistic formation of metal nanoparticles, the current study is focused on the enzymes and other organic compounds involved in the biosynthesis of AgNPs. The use of each free fungal mycelium of both Stereum hirsutum and Fusarium oxysporum will be assessed. In order to identify defective mutants on the nitrate reductase structural gene niaD, fungal cultures of S.hirsutum and F.oxysporum will be selected by chlorate resistance. In addition, in order to verify if each compound identified as key-molecule influenced on the production of nanoparticles, an in vitro assay using different nitrogen sources will be developed. Lately, fungal extracellular enzymes will be measured and an in vitro assay will be done. Finally, The nanoparticle formation and its characterization will be evaluated by UV-visible spectroscopy, electron microscopy (TEM), X-ray diffraction analysis (XRD), Fourier transforms infrared spectroscopy (FTIR), and LC-MS/MS.

Synthesis, physical and magnetic properties of BaFe12O19/P(VDF-TrFE) multifunctional composites

Composite films with filler microparticles of Barium ferrite dispersed within P(VDF-TrFE) as polymeric matrix have been prepared by solvent evaporation. The lowest BaFO content of 1% wt acts as a small defect within the polymeric matrix, reducing the values of the dielectric and mechanical properties of the pure P(VDF-TrFE). For filler contents up to a 20%, the BaFO filler reinforces the matrix and measured properties increase their values. This trend is not followed by the electrical conductivity. We extended the study to fibers composed by BaFe12O19 microparticles in a PVDF matrix. Due to the big size of BaFO particles (1 micron in diameter), proper fabrication of the fiber shaped composites has not been achieved. We found that true BaFO content are always lower than nominal ones. Results are discussed in terms of the influence of size and morphology of the BaFO particles on the initial properties of the polymeric matrix.

Relation between oral health and socioeconomic variables among schoolchildren aged 12 in the City of Manaus - AM

Studies have shown that the age of 12 was determined as the age of global monitoring of caries for international comparisons and monitoring of disease trends. The aimed was to evaluate the prevalence of dental caries, fluorosis and periodontal condition and their relation with socioeconomic factors among schoolchildren aged twelve in the city of Manaus, AM. This study with a probabilistic sample of 661 children was conducted, 609 from public and 52 from private schools, in 2008. Dental caries, periodontal condition and dental fluorosis were evaluated. In order to obtain the socioeconomic classification of each child (high, upper middle, middle, lower middle, low and lower low socioeconomic classes), the guardians were given a questionnaire. The mean decayed teeth, missing teeth, and filled teeth (DMFT) found at age twelve was 1.89. It was observed that the presence of dental calculus was the most severe periodontal condition detected in 39.48%. In relation to dental fluorosis, there was a low prevalence in the children examined, i.e., the more pronounced lines of opacity only occasionally merge, forming small white areas. The study showed a significant association of 5% among social class with dental caries and periodontal condition. In schoolchildren of Manaus there are low mean of DMFT and fluorosis, but a high occurrence of gingival bleeding.

Predictive value of clinical and electrophysiological variables in patients with chronic chagasic cardiomyopathy and nonsustained ventricular tachycardia

OBJECTIVE: Risk stratification of patients with nonsustained ventricular tachycardia (NSVT) and chronic chagasic cardiomyopathy (CCC). METHODS: Seventy eight patients with CCC and NSVT were consecutively and prospectively studied. All patients underwent to 24-hour Holter monitoring, radioisotopic ventriculography, left ventricular angiography, and electrophysiologic study. With programmed ventricular stimulation. RESULTS: Sustained monomorphic ventricular tachycardia (SMVT) was induced in 25 patients (32%), NSVT in 20 (25.6%) and ventricular fibrillation in 4 (5.1%). In 29 patients (37.2%) no arrhythmia was inducible. During a 55.7-month-follow-up, 22 (28.2%) patients died, 16 due to sudden death, 2 due to nonsudden cardiac death and 4 due to noncardiac death. Logistic regression analysis showed that induction was the independent and main variable that predicted the occurrence of subsequent events and cardiac death (probability of 2.56 and 2.17, respectively). The Mantel-Haenszel chi-square test showed that survival probability was significantly lower in the inducible group than in the noninductible group. The percentage of patients free of events was significantly higher in the noninducible group. CONCLUSION: Induction of SMVT during programmed ventricular stimulation was a predictor of arrhythmia occurrence cardiac death and general mortality in patients with CCC and NSVT.