The dimensions of the ester unit

The dimensions of the ester unit, which is a component of the depsipeptide unit has been obtained by analysing the data on crystal structures of compounds having the ester unit. The dimensions indicate that this unit is slightly different from the peptide unit both as far as the bond length and bond angles are concerned.

Dielectric properties of poly(vinylidene luoride)/CaCu3Ti4O12 nanocrystal composite thick films

The poly(vinylidene fluoride)/CaCu3Ti4O12 (CCTO) nanocrystal composite films (thickness approximate to 85 mu m) with relatively high dielectric permittivity (90 at 100 Hz) were prepared by the solution casting followed by spin coating technique. The structural, the microstructural and the dielectric properties of the composites were studied using X-ray diffraction, Scanning Electron Microscope, and Impedance analyzer respectively. The effective dielectric permittivity (e(eff)) of the composite increased with increase in the volume fraction of CCTO at all the frequencies (100 Hz to 1 MHz) under investigation. The room temperature dielectric permittivity which is around 90 at 100 Hz, has increased to about 290 at 125 degrees C (100 Hz). These results may be exploited in the development of high energy density capacitors.

Negative differential resistance in doped poly(3-methylthiophene) devices

The current density-voltage (J-V) characteristics of poly(3-methylthiophene) devices show a negative differential resistance (NDR) at room temperature with a large peak to valley current ratio (similar to 507). This NDR can be tuned by two orders of magnitude by controlling the carrier density due to the variation of the space-charge region in the device. The temperature and scan rate dependent J-V measurements infer that the NDR is mainly driven by the trapping and de-trapping of carriers. The photo-generation of carriers is observed to reduce the NDR effect.

A helical peptide containing a majority of valyl residues. The crystal structure of t-butyloxy- carbonyl-(L-valyl-_-aminoisobutyryl)3-L-valyl methyl ester onohydrate

The monohydrate of the heptapeptide t-butyloxycarbonyl-(L-valyl-α-aminoiso-butyryl)3-L-valyl methyl ester crystallizes in the orthorhombic space group P212121 with four molecules in a unit cell with the dimensions α= 9.375, b = 19.413 and c = 25.878 ÅA. The structure has been solved by direct methods and refined to an R value of 0.059 for 3633 observed reflections. The molecule in the structure exists as a slightly distorted 310-helix stabilized by five 4 -> 1 intramolecular hydrogen bonds, indicating the overwhelming influence of α-aminoisobutyryl (Aib) residues in dictating helical fold even when a majority of residues in the peptide have a low intrinsic propensity to be in helices. Contrary to what is expected in helical structures, the valyl side chains, two of which are disordered, exhibit all three possible conformations. The molecules arrange themselves in a head-to-tail fashion along the c-axis. The columns thus generated pack nearly hexagonally in the crystal.

Structural Investigations on Poly(4-hydroxy-L-proline). 2. Physicochemical Studies

We report experimental studies which confirm our prediction, namely that the ordered structure of poly(hydroxypro1ine) in solution corresponds to a left-handed helical structure with intrachain hydrogen bonds. The CD studies show that the poly(hydroxypro1ine) molecule has essentially the same conformation in aqueous solution and in the film obtained subsequently by evaporation. X-ray diffraction patterns of the sample in this form (B form) have been recorded at different relative humidities. The patterns recorded at relative humidities over 66% can be interpreted in terms of a helical structure with intrachain hydrogen bonds. These results lead us to conclude that the ordered conformation of poly(hydroxypro1ine) in solution is form B and not form A. This offers a simple explanation for the greater stability of the poly(hydroxypro1ine) helix in solution as compared to the poly(pro1ine) form I1 helix and also for the absence of mutarotation for poly(hydroxypro1ine).

Structural Investigations on Poly(4-hydroxy-L-proline). 1. Theoretical Studies

Model building studies on poly(hydroxypro1ine) indicate that in addition to the well-known helical structure of form A, a left-handed helical structure with trans peptide units and with h = 2.86 A and n = 2.67 (i.e., 8 residues in 3 turns) is also possible. In this structure which is shown to be in agreement with X-ray data of the form B in the next paper, the y-hydroxyl group of an (i + 1)th Hyp residue is hydrogen bonded to the carbonyl oxygen of an (i - 1)th residue. The possibility of a structure with cis peptide units is ruled out. It is shown that both forms A and B are equally favorable from considerations of intramolecular energies. Since form B is further stabilized by intrachain hydrogen bonds, we believe that this is likely to be the ordered conformation for poly(hydroxypro1ine) in water.

Miscibility of poly(phenyl acrylate) with acrylonitrile/styrene copolymers

The Blase transition and phase behavior of blends of poly(pheny1 acrylate) with poly(acrylonitri1eco-styrene) was studied by differential scanning calorimetry. It was found that poly(pheny1 acrylate) is miscible with poly(acrylonitri1e-co-styrenes) within a specific range of copolymer composition. The segmental interaction parameters were estimated and found to be positive for all three pairs. The miscibility in thissystem appears to be the consequence of the intramolecular repulsion between styrene and acrylonitrile units.

Poly propyl ether imine (PETIM) dendrimer: A novel non-toxic dendrimer for sustained drug delivery

In the present study, an attempt was made to study the acute and sub-acute toxicity profile of G3-COOH Poly (propyl ether imine) PETIM] dendrimer and its use as a carrier for sustained delivery of model drug ketoprofen. Drug-dendrimer complex was prepared and characterized by FTIR, solubility and in vitro drug release study. PETIM dendrimer was found to have significantly less toxicity in A541 cells compared to Poly amido amine (PAMAM) dendrimer. Further, acute and 28 days sub-acute toxicity measurement in mice showed no mortality, hematological, biochemical or histopathological changes up to 80 mg/kg dose of PETIM dendrimer. The results of study demonstrated that G3-COOH PETIM dendrimer can be used as a safe and efficient vehicle for sustained drug delivery. (C) 2010 Elsevier Masson SAS. All rights reserved.

A kinetic investigation of thermal degradation of poly(vinyl formals)

Several samples of poly(vinyl formal) having the same vinyl alcohol content (8–9%) but varying contents of vinyl acetate (6–22%) and vinyl formol (70–85%) were prepared and subjected to thermogravimetric analysis, in air and nitrogen atmospheres, employing both isothermal and dynamic methods. Kinetic parameters determined from both the isothermal and dynamic TGA data are compared. The activation energy is seen to be largely dependent on the degree of conversion, implying a complex degradation reaction. The activation energy is also much less for degradation in air than in nitrogen, which can be explained by a reaction with oxygen-producing structures favoring degradation. The activation energy is less sensitive to variation in polymer composition for degradation in air than in nitrogen. Thus, in the dynamic process, the activation energy value decreases (from 36 to 23 kcal/mole) with increasing acetate content (from 6 to 22%) in nitrogen atmosphere, while in air the activation energy value increases only moderately (from 21 to 27 kcal/mole) with increasing acetate content (from 6 to 22%). The order of reaction is nearly unity, irrespective of the composition of the polymer, both in air and nitrogen.

A kinetic investigation of thermal degradation of poly(vinyl formals)

Several samples of poly(vinyl formal) having the same vinyl alcohol content (8–9%) but varying contents of vinyl acetate (6–22%) and vinyl formol (70–85%) were prepared and subjected to thermogravimetric analysis, in air and nitrogen atmospheres, employing both isothermal and dynamic methods. Kinetic parameters determined from both the isothermal and dynamic TGA data are compared. The activation energy is seen to be largely dependent on the degree of conversion, implying a complex degradation reaction. The activation energy is also much less for degradation in air than in nitrogen, which can be explained by a reaction with oxygen-producing structures favoring degradation. The activation energy is less sensitive to variation in polymer composition for degradation in air than in nitrogen. Thus, in the dynamic process, the activation energy value decreases (from 36 to 23 kcal/mole) with increasing acetate content (from 6 to 22%) in nitrogen atmosphere, while in air the activation energy value increases only moderately (from 21 to 27 kcal/mole) with increasing acetate content (from 6 to 22%). The order of reaction is nearly unity, irrespective of the composition of the polymer, both in air and nitrogen.

Mesoporous Carbon and Poly(3,4-ethylenedioxythiophene) Composite as Catalyst Support for Polymer Electrolyte Fuel Cells

In situ polymerization of 3,4-ethylenedioxythiophene with sol-gel-derived mesoporous carbon (MC) leading to a new composite and its subsequent impregnation with Pt nanoparticles for application in polymer electrolyte fuel cells (PEFCs) is reported. The composite exhibits good dispersion and utilization of platinum nanoparticles akin to other commonly used microporous carbon materials, such as carbon black. Pt-supported MC-poly(3,4-ethylenedioxythiophene) (PEDOT) composite also exhibits promising electrocatalytic activity toward oxygen reduction reaction, which is central to PEFCs. The PEFC with Pt-loaded MC-PEDOT support exhibits 75% of enhancement in its power density in relation to the PEFC with Pt-loaded pristine MC support while operating under identical conditions. It is conjectured that Pt-supported MC-PEDOT composite ameliorates PEFC performance/durability on repetitive potential cycling. (C) 2010 The Electrochemical Society. DOI: 10.1149/1.3486172] All rights reserved.

Estimation Of Charge Transport Parameters And Equivalent Circuit For Poly Alkyl Thiophene Field-Effect Transistors

The small signal ac response is measured across the source-drain terminals of organic field-effect transistors (OFET) under dc bias to obtain the equivalent circuit parameters of poly(2,5-bis(3-tetradecylthiophen-2-yl)thieno[3,2-b]thiophene) (PBTTT) and poly(3-hexyl thiophene) (P3HT) based devices. The numerically simulated response based on these parameters is in good agreement with the experimental data for PBTTT-FET except at low frequencies, while the P3HT-FET data show significant deviations. This indicates that the interface with the metal electrode is rather complex for the latter, involving additional circuit elements arising from contact impedance or charge injection processes. Such an investigation can help in identifying the operational bottlenecks and to improve the performance of OFETs.