Growth of calcium phosphate coating on Ti-7.5Mo alloy after anodic oxidation

Titanium and its alloys are widely used as biomaterials due to their mechanical, chemical and biological properties. To enhance the biocompatibility of titanium alloys, various surface treatments have been proposed. In particular, the formation of titanium oxide nanotubes layers has been extensively examined. Among the various materials for implants, calcium phosphates and hydroxyapatite are widely used clinically. In this work, titanium nanotubes were fabricated on the surface of Ti-7.5Mo alloy by anodization. The samples were anodized for 20 V in an electrolyte containing glycerol in combination with ammonium fluoride (NH4F, 0.25%), and the anodization time was 24 h. After being anodized, specimens were heat treated at 450 °C and 600°C for 1 h to crystallize the amorphous TiO2 nanotubes and then treated with NaOH solution to make them bioactive, to induce growth of calcium phosphate in a simulated body fluid. Surface morphology and coating chemistry were obtained respectively using, field-emission scanning electron microscopy (FEG-SEM), AFM and X-ray diffraction (XRD). It was shown that the presence of titanium nanotubes induces the growth of a sodium titanate nanolayer. During the subsequent invitro immersion in a simulated body fluid, the sodium titanate nanolayer induced the nucleation and growth of nano-dimensioned calcium phosphate. It was possible to observe the formation of TiO2 nanotubes on the surface of Ti-7.5Mo. Calcium phosphate coating was greater in the samples with larger nanotube diameter. These findings represent a simple surface treatment for Ti-7.5Mo alloy that has high potential for biomedical applications. © (2013) Trans Tech Publications, Switzerland.

Photoelectrocatalytic oxidation of hair dye basic red 51 at W/WO 3/TiO2 bicomposite photoanode activated by ultraviolet and visible radiation

We prepared a W/WO3/TiO2 bicomposite photoanode by simple electrochemical anodization of W foil, followed by cathodic electrodeposition of TiO2 and annealing at 450 C for 30 min. This photoanode shows good photoactivity under irradiation with UV and visible light. In optimized conditions, it promotes complete photoelectrocatalytic oxidation of 3.33 × 10-5 mol L-1 basic red 51 solution (which is used in hair dye) at 0.1 mol L-1 Na2SO4, pH 2.0, under a current density of 1.25 mA cm-2 and ultraviolet and visible radiation-total organic carbon removal is 94 and 88%, respectively. This effect paves the way for the sustainable solar-assisted remediation of water bodies contaminated with organic components of hair dyes. © 2013 Elsevier Ltd. All rights reserved.

Optical properties of the MoO3-TiO2 particulate system and its use as a ceramic pigment

Mo-doped TiO2 powders were prepared using a dry mixture of TiO2 and MoO3 oxides with several compositions, followed by a calcination step at several temperatures. The resulting oxide system develops yellow and green tones. The XRD patterns showed only traces of MoO 3; however, EDS results, combined with TG/DTA data, confirmed the presence of molybdenum ions, suggesting that the changes in optical properties of the oxide system is due to the incorporation of Mo ions into the TiO 2 matrix, substituting Ti+4 with Mo+6 ions. The band gap decreased with increasing of MoO3 content; on the other hand, the band gap reached a maximum value at about 850°C to 910°C when plotted as a function of the calcination temperature. The glazes produced showed that the oxide system under study is a potential material for use as abinary ceramic pigment. Copyright © 2013 Taylor & Francis Group, LLC.

Development of a new method to prepare nano-/microparticles loaded with extracts of azadirachta indica, their characterization and use in controlling plutella xylostella

Biodegradable nanoparticles have been widely explored as carriers for controlled delivery of therapeutic molecules; however, studies describing the development of nanoparticles as carriers for biopesticide products are few. In this work, a new method to prepare nanoparticles loaded with neem (Azadirachta indica) extracts is presented. In this study, nanoparticles were formulated as colloidal suspension and (spray-dried) powder and characterized by evaluating pH, particle size, zeta potential, morphology, absolute recovery, and entrapment efficiency. A high-performance liquid chromatography method was used for nanoparticle characterization. The best formulations presented absolute recovery and entrapment efficiencies of approximately 100% and a release profile based on swelling and relaxation of the polymer or polymer erosion. The biological data of the formulated products against Plutella xylostella showed 100% larval mortality. The nanoparticle information improved the stability of neem products against ultraviolet radiation and increased their dispersion in the aqueous phase. © 2013 American Chemical Society.

Soft-chemical synthesis, characterization and humidity sensing behavior of WO3/TiO2 nanopowders

Tungsten oxide/titania (WO3/TiO2) nanopowders were synthesized by the polymeric precursor method which varied the WO3 content between 0 and 10 mol%. The powders were thermally treated in a conventional furnace and their structural, microstructural and electric properties were evaluated by X-ray diffraction (XRD), Raman spectrometry, N 2 physisorption, NH3 chemisorption, temperature-programmed reduction (TPR), X-ray absorption near-edge spectroscopy (XANES) in situ XANES and extended X-ray absorption fine structure spectroscopy (EXAFS) and transmission electron microscopy (TEM). XRD and Raman spectrometry confirmed the homogeneous distribution of an amorphous WO3 phase in the TiO 2 matrix which stabilized the anatase phase through the generation of [TiO5·V0] or [TiO5·V 0] complex sites. Conventional TPR-H2 (temperature programmed reduction) along with XANES TPR-H2 and XANES TPR-EtOH showed that WO3/TiO2 sample reduction occurs through the formation of these complex clusters. Moreover, the addition of WO3 promoted an increase in the surface acidity of doped samples as revealed by NH3 chemisorption. The WO3/TiO2 bulk-ceramic samples were further used to estimate their potential application in a humidity sensor in the range of 15-85% relative humidity. Probable reasons that lead to the different humidity sensor responses of samples were given based on the structural and surface characterizations. Correlation between the sensing performance of the sensor and its structural features are also discussed. Although all samples responded as a humidity sensor, the W2T sample (2 mol% added WO3) excelled for sensitivity due to the increase in acid sites, optimum mean pore size and pore size distribution. © 2013 Elsevier B.V.

Estudo das condições de coagulação/flogulação para remoção do catalisador TiO2 do meio reacional após fotodegradação da carga orgânica

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Fotocatálise heterogênea em instrumental odontológico recoberto com nanopartículas TiO2 e Ag

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Clareamento dental com perôxido de hidrogênio contendo nano partículas de óxido de titânio como semicondutor: efeito de concentrações, tempos e formas de ativação

Pós-graduação em Ciências Odontológicas - FOAR

Desenvolvimento de sistemas líquido-cristalinos multifuncionais contendo nanopartículas de TiO2 para proteção solar e liberação controlada de terpinem-4-ol

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Caracterização de propriedades de vidros polarizados do sistema P2O5 – B2O3 – CaO – TiO2

Pós-graduação em Ciência dos Materiais - FEIS

Célula solar de SnO2/TiO2 preparada por spray - pirólise ativada com corante orgânico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Um estudo da dependência do índice de refração linear com a composição dos vidros teluretos dos sistemas TeO2-Li2O-TiO2 e TeO2-Li2O-WO3

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Construção, estudo analítico e aplicação físico-química do eletrodo 'PT'|'HG'|'HG IND.2 C IND.2 O IND.4'| grafite, em meio aquoso de 'NACLO IND.4' e 'NANO IND.3'

Pós-graduação em Química - IQ

Caracterização térmica e mecânica de cerâmicas porosas com camadas de TiO2 e Al2O3

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Obtenção de fotocatalisadores magnéticos a partir de resíduos industriais e TiO2 para a degradação de contaminantes orgânicos

In this work, magnetic photocatalysts were synthesized containing differents levels of TiO2 (40, 60 e 80%) supported at the supporter of C/LV, forming the photocatalysts 40, 60, 80Ti/C/LV, using tar pitch as carbon (C) source and red mud (LV) as iron source. The prepared magnetic photocatalysts and TiO2 were used to degrade the Remazol Black textile dye (PR5) and the organic material present in samples of a textile dye effluent. The characterization of photocatalysts by Raman, X-Ray Diffraction, Transmission Electron Micoscope and Scanning, Energy Dispersive X-ray Spectrometry, Termogravimetry and Elemental Analysis, confirms the presence of carbon and magnetite in support C/LV and the presence of TiO2 in prepared photocatalysts. The photocatalytic reactions with TiO2 were analyzed by different experimental conditions, such as: mass of TiO2 (30-240 mg), solution pH (2-10), light intensity (0.871 and 1.20 mWcm-2), type of radiation (UV and sunlight-1.420 mWcm-2), radiation incidence area (44.2 to 143.1 cm2) and dissolved oxygen (OD, 1.9 and 7.6 mg L- 1). Results showed that reactions with the following conditions: 220 mg of TiO2, pH 10, solar radiation, 7.6 mg L-1 of OD and an incidence area of radiation of 143.1 cm2 showed the best results for degradation of PR5 dye. Photocatalytic reactions with magnetic photocatalysts for degrading PR5 shows that efficiency increases with TiO2 content in the C/LV support, where, above 60% of TiO2, there was not significant increase in reaction velocity. In addition, solar radiation has proved to be advantageous for photocatalytic reactions. In order to verify the presence of a non-magnetic fraction in the photocatalyst 60Ti/C/LV0, magnetic separation was proceeded. The characterizations of the magnetic (FM) and nonmagnetic (NMF) fraction confirmed that about 25% of TiO2 did not fixed in 60Ti/C/LV photocatalyst. Results of photocatalytic reactions with FM and FNM showed that both phases have photocatalytic activity for degradation of PR5. The reactions executed for the degradation of organic matter present in the actual sample of textile effluent showed that TiO2 and magnetic photocatalyst 60Ti/C/ LV have better results for color removal (85 to 35%), soluble solids ( 11 and 3%), DQO (90 and 86%) and turbidity (94 and 11%) than the treatment done by the textile industry. Sedimentation kinetics tests in presence of a magnet showed that photocatalysts are separated faster from aqueous environment than pure TiO2. Obtained results showed that magnetic photocatalysts have excellent photocatalytic activity and can be separated from the reaction environment on a simple and quick way when a magnetic field is applied.