Produção de chapas de partículas com resíduos de madeira Cordia goeldiana

The aim of this research consisted in the use of wastes from tropical wood (Cordia goeldiana) with low density and the polyurethane resin (mono and bicomponent) castor oil based in the manufacture of particleboards, generating subsidies as application in rural and civil construction, as well in the furniture industry. The particleboards were manufactured with 15% of polyurethane resin content (one part of pre-polymer and one part of polyol), compaction pressure of 4MPa, pressing temperature of 90 degrees C and press time of 7 minutes. The physical and mechanical properties investigated were density, moisture content, strength modulus in bending and internal bond, both obtained according to the recommendations of the Brazilian standard ABNT NBR 14810:2002. The mean values obtained for these properties were systematically superior to the Brazilian standard requirement. This point showed that it is possible the use of Cordia goeldiana wastes in the particleboard production. We confirmed the hypothesis of a significant linear relation between density and the internal bond of the panels, allowing the estimation of the internal bond of particleboards.

Determination of soil properties from standard penetration test complemented by torque measurement (SPT-T)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise do desempenho térmico de habitações populares da microrregião de Guaratinguetá - SP

Pós-graduação em Engenharia Mecânica - FEG

Sistema de gestão da qualidade numa organização pública de P&D: fatores que influenciam a certificação

Pós-graduação em Engenharia Mecânica - FEG

Uso da espectroscopia do infravermelho próximo (NIR) como método não destrutivo para a discriminação de aguardentes de cana-de-açúcar produzidas no Estado de São Paulo e Minas Gerais, e predição do teor de etanol

Pós-graduação em Alimentos e Nutrição - FCFAR

Caracterização físico-mecânica de painéis de partículas de bambu com adição de casca de café

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Conformidade ergonômica dos controles no posto de trabalho do operador de trator: estudo de caso NH 7630

This article discusses an ergonomic analysis of the controls used by tractor operators, covering their positions in relation to the casing of your job. Was performed an assessment of the controls of the job of a model NH 7630 tractor average power of 74 kW (100 CV), using the norms of the ABNT. With this screening could detect the positive and negative. Then was accomplished an analytical study of the controls. Evaluation results show that some controls of tractors have errors evaluated in relation to NBR/ ISO 6682.

Comparativo ergonômico de duas metododologias para aquisição de coordenadas tridimensionais do posto de trabalho do operador de trato

This research aimed to the comparison between two methods for obtaining three-dimensional coordinates of the controls of the upper limbs of the job of the tractor operator. The methods used were based on NBR / NM / ISO 5353 - Road machines, tractors and agricultural and forestry machinery – Reference point of the seat. The first method used follows the principles recommended by the standard NBR/NM/ISO/5353 The second method is an adaptation of this standard with the introduction of a laser measuring equipment developed by Silva (2009). The results were compared statistically to evaluate differences between the methodological processes involved. In this research, data was collected thought a brand new tractor Massey Ferguson model MF 292, awarded by the dealership from Londrina. The results have shown a considerable variation between the traditional measurement process and the laser measuring. It must be considered that this variation can be used to calibrate the tractor controls positioning, therefore the tractor is not in accordance to ABNT.

Análise da incorporação de resíduos de pás eólicas em cimento portland atrvés de imagens de raios-X

Introdução: Os processos industriais geram grandes quantidades de resíduos, representando um grande desperdício de matéria prima e causando impactos negativos ao meio ambiente. No caso dos resíduos gerados pelas fábricas de pás eólicas para aerogeradores de Sorocaba-S.P., eles podem ser reaproveitados na incorporação em cimento Portland. O interesse é utilizá-los na construção civil como blocos sem fins estruturais para construção de muros, guias, calçadas, pisos, etc. Os corpos confeccionados devem obedecer às normas técnicas brasileiras e as suas propriedades relativas à resistência, compressão, absorção de água e distribuição espacial dos resíduos nestes corpos devem ser avaliadas. Objetivos: Devido à importância de se conhecer as propriedades dos corpos produzidos com a incorporação de resíduos de pás eólicas, este trabalho faz uma avaliação através de imagens de raios X de sua distribuição espacial para verificar a viabilidade do emprego desta técnica no estudo da incorporação de resíduos para, futuramente, em conjunto com outras pesquisas que estão sendo realizadas, verificar a relação desta distribuição com as propriedades mecânicas dos corpos produzidos. Métodos: Objetivando a incorporação desse resíduo como substituto parcial dos agregados miúdos em argamassa, foram fabricados corpos de prova (CPs) seguindo as normas da ABNT-NBR 5738. Todos os corpos foram desmoldados após 24 horas de sua confecção e imersos em água por 28 dias para a cura. Utilizou-se o traço 3:1, areia e cimento, em relação a massa dos componentes, ou seja, para cada 300 g de areia adicionou-se 100 g de cimento. Na confecção de argamassa com resíduo utilizou-se o mesmo traço, porém com a substituição de parte da areia pelo resíduo. Foram fabricados CPs com 5%, 15%, 50% e 0% de resíduo para que este sirva de referência. Como os corpos possuem um formato cilíndrico, foram obtidas imagens em duas projeções: frontal e superior utilizando um equipamento digital com os seguintes parâmetros: 83 kVp e 16 mAs e, 85 kVp e 30 mAs, respectivamente. Resultados: As imagens mostram que na projeção frontal é possível verificar que a distribuição do resíduo nos corpos é homogênea, o que pode proporcionar uniformidade nos resultados de testes de resistência à compressão que serão realizados futuramente. Porém, na projeção superior ainda será necessário um estudo dos parâmetros que deverão ser utilizados no equipamento de raios X para melhorar a sua qualidade. Além disso, métodos de processamento digital de imagens poderão ser aplicados nas imagens para auxiliar na visualização dos resíduos incorporados. Também pode ser visto nas imagens que a forma utilizada para a incorporação do resíduo resulta na sua distribuição uniforme, compatível com o que se deseja neste tipo de incorporação.

Aproveitamento do resíduo do processamento do café na composição de painéis MDP

A produção de produtos derivados de madeira e bambu vem crescendo nos últimos anos na busca de um aproveitamento mais racional dessas matériasprimas. Este trabalho tem por finalidade, o estudo da aplicação de resíduos do processamento do café em um painel MDP. Os painéis MDP foram produzidos com partículas de bambu da espécie Dendrocalamus giganteus e adição de partículas de casca de café na camada intermediária do painel, unidas por resina poliuretana à base de mamona. A caracterização físico-mecânica foi realizada baseando-se nas especificações da NBR 14810-3 (2006). Os resultados obtidos foram comparados com a norma brasileira NBR 14810-2 (2006), resultando em valores próximos aos comercialmente encontrados.

Evaluation of longitudinal modulus of elasticity in wood species for structural application

1024x768 This research aimed to investigate possible differences in values of longitudinal modulus of elasticity for wood species usually employed for structural purposes, as Castanheira (Bertholletia excelsa), Cambará (Erisma uncinatum), Cumaru (Dipteryx odorata), Jatobá (Hymenaea stilbocarpa), Garapa (Apuleia leiocarpa) and Peroba Rosa (Aspidosperma polyneuron), obtained from compression and tension parallel to grain, and static bending tests. Recommendations of the Brazilian standard ABNT NBR 7190:1997, Annex B, were followed. Statistical analysis results for the cited properties, had equivalent averages for the six wood species analyzed. This confirms that any of the three tests can be used to obtain the longitudinal elastic modulus and which could avoid the necessity of evaluating stiffness values for wood by more than one kind of mechanical test. Normal 0 21 false false false PT-BR X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabela normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

Influence of moisture content in some mechanical properties of two brazilian tropical wood species

This study aimed, with the aid of analysis of variance (ANOVA), to investigate and quantify the influence of moisture ranging between 12% and over 30% (fiber saturation) on the mechanical properties: strength and modulus of elasticity in compression and in tension parallel to grain; modulus of rupture and modulus of elasticity in static bending; shear strength parallel to grain considering wood species Ipê (Tabebuia sp) and Angelim Araroba (Vataireopsis araroba). Tests were performed according to the assumptions and calculating methods Brazilian standard ABNT NBR 7190, Anexx B, totalizing 400 tests. Results of ANOVA revealed a significant reduction (16% on average) for mechanical properties wood due to the increase in moisture content from 12% to over 30% (fiber saturation). The same behavior also occurred when assembly containing the two species was considered.

Evaluation of bamboo particleboards produced with urea-formaldheyde resin

The bamboo waste can be an alternative material to sustain the crescent demand for particleboards, also bringing ecological benefits as reduction of the pressure for raw materials and landfill space demands. In this context, this research aimed to manufacture and determine some physical and mechanical properties of particleboards with bamboo waste particles (Dendrocalamus giganteus), obtained from different sources, bonded with four different percentages of urea–formaldehyde (UF) based resin (6%, 8%, 10% and 12% related to dry material of particles). Response variables investigated were: density; moisture content; thickness swelling in 2 and 24 hours; water absorption in 2 and 24 hours; internal adhesion (STpe); strength in tension parallel to faces (STpa); modulus of elasticity (MOE) and modulus of rupture (MOR). Results permitted to conclude that particleboards as mentioned showed good performance only in the physical properties requirements imposed by Brazilian Standard NBR 14810, but this was not observed to mechanical properties considered. New researches are needed in order to optimize the producing process parameters.

Physical characterization of particleboard produced with waste from ethanol and sugar mill

The problem of proper disposal of solid waste generated in different industrial processes is one of worldwide environmental concerns nowadays. Thus, this study aimed to establish a new alternative for the disposal of two agro-industrial residues employing them to produce particleboard for different purposes in building construction. The focus was given to the reuse of the sugarcane bagasse (SB) originated during the processing of Saccharum officinarum for sugar and ethanol production, and bamboo stem leaves of Dendrocalamus giganteus(BB). For this, six particleboards were produced in the following compositions: with 100% SB, 75% SB + 25% BB, 50% SB+50% BB, 40% SB +60 BB, 25% SB+ 75% BB and 100% BB in the total mass of the composites. The particleboards physical characterization followed Brazilian Standard ABNT NBR 14810-3 to density, moisture content and water absorption. Results showed these raw materials are compatible to particleboard production.

Study of the feasibility of mix of species from sawmill waste and limiting for particleboard

This study aims to determine physical properties of particleboard made of sawmill waste, as a mix of several wood species, and two adhesives: urea-formaldehyde, usually employed in industry (even with drawbacks or formaldehyde emission during pressing) and FASTBOND®, water based resin, still poorly referenced in literature. Sixteen panels have been produced, in four experimental conditions, defined by using two adhesives and a 12 mm thick limiter (or not). Variance analysis was adopted to evaluate influence of experimental conditions on physical properties of produced panels, manufactured in nominal dimensions 350x350mm; 10% resin related to particles mass (at 5% moisture); 3.5 MPa compaction pressure, temperature 130°C, in a 10 min cycle. Tests to determine density, moisture content, swelling and water absorption were carried out based on normative parameters of ABNT NBR 14810:2006. Results have been satisfactory to panels produced with urea-formaldehyde but those manufactured with polychloroprene based resin (FASTBOND®) not meet regulatory requirements. Best results have been obtained without limiter.