957 resultados para Multiprocessor on chip


Relevância:

30.00% 30.00%

Publicador:

Resumo:

A sensitive and fast-responding membrane-free amperometric gas sensor is described, consisting of a small filter paper foil soaked with a room temperature ionic liquid (RTIL), upon which three electrodes are screen printed with carbon ink, using a suitable mask. It takes advantage of the high electrical conductivity and negligible vapour pressure of RTILs as well as their easy immobilization into a porous and inexpensive supporting material such as paper. Moreover, thanks to a careful control of the preparation procedure, a very close contact between the RTIL and electrode material can be achieved so as to allow gaseous analytes to undergo charge transfer just as soon as they reach the three-phase sites where the electrode material, paper supported RTIL and gas phase meet. Thus, the adverse effect on recorded currents of slow steps such as analyte diffusion and dissolution in a solvent is avoided. To evaluate the performance of this device, it was used as a wall-jet amperometric detector for flow injection analysis of 1-butanethiol vapours, adopted as the model gaseous analyte, present in headspace samples in equilibrium with aqueous solutions at controlled concentrations. With this purpose, the RTIL soaked paper electrochemical detector (RTIL-PED) was assembled by using 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl) imide as the wicking RTIL and printing the working electrode with carbon ink doped with cobalt(II) phthalocyanine, to profit from its ability to electrocatalyze thiol oxidation. The results obtained were quite satisfactory (detection limit: 0.5 mu M; dynamic range: 2-200 mu M, both referring to solution concentrations; correlation coefficient: 0.998; repeatability: +/- 7% RSD; long-term stability: 9%), thus suggesting the possible use of this device for manifold applications.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The most important property of austenitic stainless steels is corrosion resistance. In these steels, the transition between paramagnetic and ferromagnetic conditions occurs at low temperatures. Therefore, the use of austenitic stainless steels in conditions in which ferromagnetism absence is important can be considered. On the other hand, the formation of strain-induced martensite is detected when austenitic stainless steels are deformed as well as machined. The strain-induced martensite formed especially in the machining process is not uniform through the chip and its formation can also be related to the Md temperature. Therefore, both the temperature distribution and the gradient during the cutting and chip formation are important to identify regions in which martensite formation is propitiated. The main objective here is evaluate the strain-induced martensite formation throughout machining by observing microstructural features and comparing these to thermal results obtained through finite element method analysis. Results show that thermal analysis can give support to the martensite identified in the microstructural analysis.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

In two Italian sites, multiaxis trees slightly reduced primary axis length and secondary axis length of newly grafted trees, and increased the number of secondary shoots. The total length, node production, and total dry matter gain were proportional to the number of axis. Growth of both primary and secondary shoots, and dry matter accumulation, have been found to be also well related to rootstock vigour. A great variability in axillary shoot production was recorded among different environments. Grafted trees had higher primary growth, secondary axis growth, and dry matter gain than chip budded trees. Stem water potential measured in the second year after grafting was not affected by rootstocks or number of leaders. Measurements performed in New Zealand (Hawke’s Bay) during the second year after grafting revealed that both final length and growth rate of primary and secondary axis were related to the rootstock rather than to the training system. Dwarfing rootstocks reduced the number of long vegetative shoots and increased the proportion of less vigorous shoots.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The new generation of multicore processors opens new perspectives for the design of embedded systems. Multiprocessing, however, poses new challenges to the scheduling of real-time applications, in which the ever-increasing computational demands are constantly flanked by the need of meeting critical time constraints. Many research works have contributed to this field introducing new advanced scheduling algorithms. However, despite many of these works have solidly demonstrated their effectiveness, the actual support for multiprocessor real-time scheduling offered by current operating systems is still very limited. This dissertation deals with implementative aspects of real-time schedulers in modern embedded multiprocessor systems. The first contribution is represented by an open-source scheduling framework, which is capable of realizing complex multiprocessor scheduling policies, such as G-EDF, on conventional operating systems exploiting only their native scheduler from user-space. A set of experimental evaluations compare the proposed solution to other research projects that pursue the same goals by means of kernel modifications, highlighting comparable scheduling performances. The principles that underpin the operation of the framework, originally designed for symmetric multiprocessors, have been further extended first to asymmetric ones, which are subjected to major restrictions such as the lack of support for task migrations, and later to re-programmable hardware architectures (FPGAs). In the latter case, this work introduces a scheduling accelerator, which offloads most of the scheduling operations to the hardware and exhibits extremely low scheduling jitter. The realization of a portable scheduling framework presented many interesting software challenges. One of these has been represented by timekeeping. In this regard, a further contribution is represented by a novel data structure, called addressable binary heap (ABH). Such ABH, which is conceptually a pointer-based implementation of a binary heap, shows very interesting average and worst-case performances when addressing the problem of tick-less timekeeping of high-resolution timers.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Eine funktionierende Proteinqualitätskontrolle ist essenziell für die Vitalität einer Zelle. Das dynamische Gleichgewicht zwischen Proteinfaltung und -degradation wird von molekularen Chaperonen aufrechterhalten, deren Aktivität wiederum durch die Interaktion mit zahlreichen Cochaperonen moduliert wird. Das Cochaperon CHIP ist ein zentraler Faktor in Proteintriage-Entscheidungsprozessen, da es als Ubiquitinligase Chaperonsubstrate dem Abbau zuführt und somit die Chaperonmaschinerie direkt mit den Systemen der Proteindegradation verbindet. Um Polypeptide vor einem vorzeitigen Abbau zu schützen, wird die destruktive Aktivität von CHIP durch weitere Cochaperone reguliert. rnIn dieser Arbeit konnte die Hemmung der Ligaseaktivität von CHIP durch das Cochaperon BAG2 mechanistisch erstmals in einem zellulären System nachgewiesen werden. Dazu wurde die humane IMR-90 Fibroblasten Zelllinie verwendet. Die Ubiquitinierungsaktivität von CHIP wurde anhand von HSP72 als Modell-CHIP-Substrat untersucht. Durch die verringerte Ubiquitinierung, und damit dem reduzierten Abbau von HSP72, regulierte BAG2 dessen intrazelluläre Proteinspiegel, ohne dabei selbst eine Hitzeschockantwort zu induzieren. Überexprimiertes BAG2 wirkte sich trotz stabilisierter HSP72-Spiegel bei einem appliziertem Hitzestresses negativ auf die Zellvitalität aus, vermutlich da BAG2 durch die Inhibition von CHIP-vermittelter Ubiquitinierung massiv in das Gleichgewicht zwischen Substratfaltung und -degradation eingreift.rnDa sich die Mechanismen der Proteinqualitätskontrolle in der Alterung stark verändern und sich den wandelnden Bedingungen in der Zelle anpassen, wurde in einem zweiten Teil dieser Arbeit mit Hilfe des IMR-90 Zellsystems als etabliertes Modell zellulärer Seneszenz analysiert, inwieweit sich die Aktivität und die Regulation von CHIP durch BAG2 in der zellulären Alterung ändern. In seneszenten Zellen war HSP72 erheblich weniger ubiquitiniert als in jungen Fibroblasten, was auf eine reduzierte CHIP-Aktivität hinweist. Diese blieb jedoch durch BAG2 weiterhin modulierbar. Die Funktion von BAG2 als Inhibitor der Ubiquitinligase CHIP blieb demnach in seneszenten Zellen bestehen. In gealterten Fibroblasten regulierte BAG2 außerdem die Proteinspiegel des CHIP-Substrates und Seneszenzinitiators p53, was BAG2 eine mögliche Rolle in der Etablierung des Seneszenz-Phänotyps zuspricht. Weiterhin unterlagen die Proteinspiegel der beiden funktionell redundanten CHIP-Modulatoren BAG2 und HSPBP1 in der zellulären Alterung einer reziproken Regulation. In gealterten Mäusen trat die gegenläufige Veränderung der beiden Cochaperone gewebsspezifisch in der Lunge auf. Außerdem waren die BAG2-Proteinspiegel im Hippocampus gealterter Tiere signifikant erhöht.rnZusammenfassend konnte anhand der erzielten Ergebnisse die Funktion von BAG2 als Inhibitor von CHIP im zellulären System bestätigt werden. Außerdem durchlaufen die Aktivität und die Regulation von CHIP einen seneszenzspezifischen Adaptationsprozess, welcher für die Erhaltung der Proteostase in der Alterung relevant sein könnte und in welchem die Funktion von BAG2 als CHIP-Modulator möglicherweise eine wichtige Rolle spielt.rnZukünftige Studien könnten die komplexen Mechanismen weiterführend aufklären, mit denen CHIP-Aktivität reguliert wird. Dies kann helfen, der altersbedingten Abnahme an proteostatischer Kontrolle entgegenzuwirken und aberrante Proteinaggregation in altersassoziierten Erkrankungen vorzubeugen.rn

Relevância:

30.00% 30.00%

Publicador:

Resumo:

We present a microfluidic epithelial wound-healing assay that allows characterization of the effect of hepatocyte growth factor (HGF) on the regeneration of alveolar epithelium using a flow-focusing technique to create a regular wound in the epithelial monolayer. The phenotype of the epithelial cell was characterized using immunostaining for tight junction (TJ) proteins and transmission electron micrographs (TEMs) of cells cultured in the microfluidic system, a technique that is reported here for the first time. We demonstrate that alveolar epithelial cells cultured in a microfluidic environment preserve their phenotype before and after wounding. In addition, we report a wound-healing benefit induced by addition of HGF to the cell culture medium (19.2 vs. 13.5 μm h(-1) healing rate).

Relevância:

30.00% 30.00%

Publicador:

Resumo:

A silicon-based microcell was fabricated with the potential for use in in-situ transmission electron microscopy (TEM) of materials under plasma processing. The microcell consisted of 50 nm-thick film of silicon nitride observation window with 60μm distance between two electrodes. E-beam scattering Mont Carlo simulation showed that the silicon nitride thin film would have very low scattering effect on TEM primary electron beam accelerated at 200 keV. Only 4.7% of primary electrons were scattered by silicon nitride thin film and the Ar gas (60 μm thick at 1 atm pressure) filling the space between silicon nitride films. Theoretical calculation also showed low absorption of high-energy e-beam electrons. Because the plasma cell needs to survive the high vacuum TEM chamber while holding 1 atm internal pressure, a finite element analysis was performed to find the maximum stress the low-stress silicon nitride thin film experienced under pressure. Considering the maximum burst stress of low-stress silicon nitride thin film, the simulation results showed that the 50 nm silicon nitride thin film can be used in TEM under 1 atm pressure as the observation window. Ex-situ plasma generation experiment demonstrated that air plasma can be ignited at DC voltage of 570. A Scanning electron microscopy (SEM) analysis showed that etching and deposition occurred during the plasma process and larger dendrites formed on the positive electrode.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

OBJECTIVES: Proteomics approaches to cardiovascular biology and disease hold the promise of identifying specific proteins and peptides or modification thereof to assist in the identification of novel biomarkers. METHOD: By using surface-enhanced laser desorption and ionization time of flight mass spectroscopy (SELDI-TOF-MS) serum peptide and protein patterns were detected enabling to discriminate between postmenopausal women with and without hormone replacement therapy (HRT). RESULTS: Serum of 13 HRT and 27 control subjects was analyzed and 42 peptides and proteins could be tentatively identified based on their molecular weight and binding characteristics on the chip surface. By using decision tree-based Biomarker Patternstrade mark Software classification and regression analysis a discriminatory function was developed allowing to distinguish between HRT women and controls correctly and, thus, yielding a sensitivity of 100% and a specificity of 100%. The results show that peptide and protein patterns have the potential to deliver novel biomarkers as well as pinpointing targets for improved treatment. The biomarkers obtained represent a promising tool to discriminate between HRT users and non-users. CONCLUSION: According to a tentative identification of the markers by their molecular weight and binding characteristics, most of them appear to be part of the inflammation induced acute-phase response

Relevância:

30.00% 30.00%

Publicador:

Resumo:

We report the fabrication, functionalization and testing of microdevices for cell culture and cell traction force measurements in three-dimensions (3D). The devices are composed of bent cantilevers patterned with cell-adhesive spots not lying on the same plane, and thus suspending cells in 3D. The cantilevers are soft enough to undergo micrometric deflections when cells pull on them, allowing cell forces to be measured by means of optical microscopy. Since individual cantilevers are mechanically independent of each other, cell traction forces are determined directly from cantilever deflections. This proves the potential of these new devices as a tool for the quantification of cell mechanics in a system with well-defined 3D geometry and mechanical properties.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The presence of congenital appendages (wattles) on the throat of goats is supposed to be under genetic control with a dominant mode of inheritance. Wattles contain a cartilaginous core covered with normal skin resembling early stages of extremities. To map the dominant caprine wattles (W) locus, we collected samples of 174 goats with wattles and 167 goats without wattles from nine different Swiss goat breeds. The samples were genotyped with the 53k goat SNP chip for a subsequent genome-wide association study. We obtained a single strong association signal on chromosome 10 in a region containing functional candidate genes for limb development and outgrowth. We sequenced the whole genomes of an informative family trio containing an offspring without wattles and its heterozygous parents with wattles. In the associated goat chromosome 10 region, a total of 1055 SNPs and short indels perfectly co-segregate with the W allele. None of the variants were perfectly associated with the phenotype after analyzing the genome sequences of eight additional goats. We speculate that the causative mutation is located in one of the numerous gaps in the current version of the goat reference sequence and/or represents a larger structural variant which influences the expression of the FMN1 and/or GREM1 genes. Also, we cannot rule out possible genetic or allelic heterogeneity. Our genetic findings support earlier assumptions that wattles are rudimentary developed extremities.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

To identify novel quantitative trait loci (QTL) within horses, we performed genome-wide association studies (GWAS) based on sequence-level genotypes for conformation and performance traits in the Franches-Montagnes (FM) horse breed. Sequence-level genotypes of FM horses were derived by re-sequencing 30 key founders and imputing 50K data of genotyped horses. In total, we included 1077 FM horses genotyped for ~4 million SNPs and their respective de-regressed breeding values of the traits in the analysis. Based on this dataset, we identified a total of 14 QTL associated with 18 conformation traits and one performance trait. Therefore, our results suggest that the application of sequence-derived genotypes increases the power to identify novel QTL which were not identified previously based on 50K SNP chip data.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The goal of the RAP-WAM AND-parallel Prolog abstract architecture is to provide inference speeds significantly beyond those of sequential systems, while supporting Prolog semantics and preserving sequential performance and storage efficiency. This paper presents simulation results supporting these claims with special emphasis on memory performance on a two-level sharedmemory multiprocessor organization. Several solutions to the cache coherency problem are analyzed. It is shown that RAP-WAM offers good locality and storage efficiency and that it can effectively take advantage of broadcast caches. It is argued that speeds in excess of 2 ML IPS on real applications exhibiting medium parallelism can be attained with current technology.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Development of PCB-integrateable microsensors for monitoring chemical species is a goal in areas such as lab-on-a-chip analytical devices, diagnostics medicine and electronics for hand-held instruments where the device size is a major issue. Cellular phones have pervaded the world inhabitants and their usefulness has dramatically increased with the introduction of smartphones due to a combination of amazing processing power in a confined space, geolocalization and manifold telecommunication features. Therefore, a number of physical and chemical sensors that add value to the terminal for health monitoring, personal safety (at home, at work) and, eventually, national security have started to be developed, capitalizing also on the huge number of circulating cell phones. The chemical sensor-enabled “super” smartphone provides a unique (bio)sensing platform for monitoring airborne or waterborne hazardous chemicals or microorganisms for both single user and crowdsourcing security applications. Some of the latest ones are illustrated by a few examples. Moreover, we have recently achieved for the first time (covalent) functionalization of p- and n-GaN semiconductor surfaces with tuneable luminescent indicator dyes of the Ru-polypyridyl family, as a key step in the development of innovative microsensors for smartphone applications. Chemical “sensoring” of GaN-based blue LED chips with those indicators has also been achieved by plasma treatment of their surface, and the micrometer-sized devices have been tested to monitor O2 in the gas phase to show their full functionality. Novel strategies to enhance the sensor sensitivity such as changing the length and nature of the siloxane buffer layer are discussed in this paper.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The latest video coding standards developed, like HEVC (High Efficiency Video Coding, approved in January 2013), require for their implementation the use of devices able to support a high computational load. Considering that currently it is not enough the usage of one unique Digital Signal Processor (DSP), multicore devices have appeared recently in the market. However, due to its novelty, the working methodology that allows produce solutions for these configurations is in a very initial state, since currently the most part of the work needs to be performed manually. In consequence, the objective set consists on finding methodologies that ease this process. The study has been focused on extend a methodology, under development, for the generation of solutions for PCs and embedded systems. During this study, the standards RVC (Reconfigurable Video Coding) and HEVC have been employed, as well as DSPs of the Texas Instruments company. In its development, it has been tried to address all the factors that influence both the development and deployment of these new implementations of video decoders, ranging from tools up to aspects of the partitioning of algorithms, without this can cause a drop in application performance. The results of this study are the description of the employed methodology, the characterization of the software migration process and performance measurements for the HEVC standard in an RVC-based implementation. RESUMEN Los estándares de codificación de vídeo desarrollados más recientemente, como HEVC (High Efficiency Video Coding, aprobado en enero de 2013), requieren para su implementación el uso de dispositivos capaces de soportar una elevada carga computacional. Teniendo en cuenta que actualmente no es suficiente con utilizar un único Procesador Digital de Señal (DSP), han aparecido recientemente dispositivos multinúcleo en el mercado. Sin embargo, debido a su novedad, la metodología de trabajo que permite elaborar soluciones para tales configuraciones se encuentra en un estado muy inicial, ya que actualmente la mayor parte del trabajo debe realizarse manualmente. En consecuencia, el objetivo marcado consiste en encontrar metodologías que faciliten este proceso. El estudio se ha centrado en extender una metodología, en desarrollo, para la generación de soluciones para PC y sistemas empotrados. Durante dicho estudio se han empleado los estándares RVC (Reconfigurable Video Coding) y HEVC, así como DSPs de la compañía Texas Instruments. En su desarrollo se ha tratado de atender a todos los factores que influyen tanto en el desarrollo como en la puesta en marcha de estas nuevas implementaciones de descodificadores de vídeo; abarcando desde las herramientas a utilizar hasta aspectos del particionado de los algoritmos, sin que por ello se produzca una reducción en el rendimiento de las aplicaciones. Los resultados de este estudio son una descripción de la metodología empleada, la caracterización del proceso de migración de software, y medidas de rendimiento para el estándar HEVC en una implementación basada en RVC.