A Novel Method for Switching and Tuning of PBG Structures

Photonic band-gap (PBG) structures are utilized in microwave components as filters to suppress unwanted signals. In this work, rectangular perforations were created in the ground plane of a microstrip line to construct a PBG structure. A gold-coated alumina substrate was utilized to switch or tune the bandstop characteristics of this structure. It was demonstrated that the bandstop characteristics were switched off from - 35 to - 1 dB at 16 GHz. Tuning of the bandstop edge with a shift of 1.5 GHz was also shown

Wideband Oylindrioal Dielectric Resonator Antenna Excited Using an L-strip Feed

A broadband cylindrical dielectric resonator antenna (DRA) energized with an L-strip feed is presented The novel exciting technique achieves a 2:1 VSWR bandwidth of 18%. The variation of bandwidth for different feed parameters is also studied

Comparison of Electromagnetic Band Gap and Split-Ring Resonator Microstrip Lines as Stop Band Structures

In this paper, microstrip lines magnetically coupled to splitring resonators (SRRs) are conquved to electromagnetic bundgup (EBG) nr,rrostrip lines in terns q/ their stop-heard penjbrnmrnce and dimensions. In bath types o/ trunsmis•siou lines, signal propagation is inhibited in it certain jequency bwuL For EBG microstrip lines, the central frequency of such a forbidden band is determined by the period of the structure, whereas in SRR-hased microstrip lines the position of the frequency gap depends on the quasi-static resonant frequency of the rings. The main relevant conrributiun of this paper is to provide a tuning procedure to control the gap width in SRR microstrip lines, and to show that by using SRRs, device dimensions ale much smaller than those required by EBGs in order to obtain similar stop-banal performance. This has been demonstrated by fill-wave electromagnetic simulations and experimentally verified from the characterization ql two fabricated microstrip lines: one with rectangular SRRs etched on the upper substrate side, and the other with a periodic perturbation cf'strip width. For similar rejection and 1-(;H,. gap width centered at 4.5 Gllz, it has been found that the SRR microstrip line is•,fve times shorter. In addition, no ripple is appreciable in the allowed band for the .SRR-hared structure, whereas due to dispersion, certain mismatch is expected in the EBG prototype. Due to the high-frequency selectivity, controllable gap width, and small dimensions, it is believed that SRR coupled to planar transmission lines can have an actual impact on the design of stop-band filters compatible with planar technology, and can be an alternative to present solutions based on distributed approaches or EBG

Design and Analysis of Microstrip Lines with EBG-Backed Ground Planes of Different Geometrical Shapes

Propagation of electromagnetic waves through a microstrip line with 2D electromagnetic baud gap (EBG) structures of different geometrical shapes in the ground plane is investigated in this paper. Using transmission-line theory, the design equations for EBG structures are calculated. The measured, numerical. and simulated results are in gone) agreement

L-strip-fed Wideband Rectangular Dielectric Resonator Antenna

In this paper, the advantages of using L-shaped microviij) feed to e.tcite a rectangular dielectric resonator cuuenna (DRA) by elemanagnetic coupling are presented. This feeding technique enhances the hardsvidth and gain of the antenna without affecting its size. The experimental re srdts are validated using Fidelity software based on the finitedifference tine-domain (FDTD) method

Rectangular Dielectric Resonator Antenna on a Conductor-backed Co-planar

In this paper, we present an effective excitation of a reelangular dielectric resonator antennas (DRA) with a conductor-hacked coplanar waveguide (CB-CPW). The radiation and resonance characteristics are found to van,, depending on the orientation of the DR on doe coplanar feed line. The effect of finite and infinite ground planes of CB-CPIV on the radiation characteristics of the rectangular DRA is studied. The orientation and position of the DR are optimized for maximum gain and bandwidth. The optimized antenna ,geometry offers --10.46 dBi gain and 7.5% bandwidth with low cross-polar radiation characteristics

Novel Wide Band Printed Dipole Antenna

Design, development and experimental observations of a L: band printed dipole antenna is presented.Bandwidth enhancement is achieved by end-loading or the dipole arms. Using the present technique Impedance bandwidth van be enhanced up to 50% without degrading the efficiency of the antenna.

An Experimental Investigation of the Effect of Flange Angle on Radiation Patterns of V-Slot Waveguide Antenna

Results of exhaustive study of the effect of metallic flanges on H-plane radiation characteristics of V-slot waveguide antenna are presented . It has been established that the beam can be sharpened or broadened by varying the flange angle . The adjustment of the flange angle and flange width would further improve the radiation pattern , yielding optimum efficiency from the flanged system

A Strip-Loaded Feed-Horn antenna

Design and development of a new feed -horn antenna with low sidelobe levels is reported . The E-walls of this antenna are fabricated with low -loss dielectric substrate , periodically loaded with thin conducting strips . The antenna is found to be simulating the radiation characteristics of metallic corrugated horns . This can be an ideal substitute for metallic corrugated horns with added advantages like light -weight and low production cost.

A Strip-Loaded Feed-Horn antenna

Design and development of a new feed -horn antenna with low sidelobe levels is reported . The E-walls of this antenna are fabricated with low -loss dielectric substrate , periodically loaded with thin conducting strips . The antenna is found to be simulating the radiation characteristics of metallic corrugated horns . This can be an ideal substitute for metallic corrugated horns with added advantages like light -weight and low production cost.

Analysis of Cavity Backed Printed Dipoles

The closed form expression for the radiated power of a half-wave microstrip patch is modified to calculate the impedance bandwidth of a printed dipole. Analyses of cavity backed flared and end-loaded printed dipoles are presented

Compact Planar Multiband Antenna for GPS,DCS 2.4/5.8 GHz WLAN Applications

A compact single - feed muttiband planar antenna configuration suitable for GPS, DCS. 2.4/5.8 GHz WLAN applications is presented. The antenna has dimensions 38 x 3 x 1.6 mm and offers good radiation and reflection characteristics in the above frequency bands. The antenna has a simple geometry and can be easily fed using a 50 coaxial probe.

Compact Wideband Antenna for 2.4 GHz WLAN Applications

A novel compact wideband antenna for wireless local area network (WLAN) applications in the 2.4 GHz band is presented. The proposed low profile antenna of dimensions 15 x 14.5 x 1.6 mm offers 18.6% bandwidth and an average gain of -5 dBi. The antenna can be excited directly using a 50 coaxial probe

DESIGN AND DEVELOPMENT OF COMPACT ASYMMETRIC COPLANAR STRIP FED ANTENNAS

Antennas are indispensable component of any wireless communication device. An antenna is a transducer between the transmitter and the free space waves and vice versa. They efficiently transfer electromagnetic energy from a transmission line into free space. But the present day communication applications require compact and ultra wide band designs which cannot be catered by simple microstrip based designs. PIFAs have solved the problem to some extend, but the field of antennas needs more innovative designs In this thesis the design and development of compact planner antenna are presented. Emphasis is given to the design of the feed as well as the radiator resulting in simple compact uniplanar geometries. The Asymmetric coplanar feed used to excite the antennas is found to be a suitable choice for feeding compact antennas.The main objectives of the study are the design of compact single, dual and multi band antennas with uniplanar structure and extension of the design for practical GSM/WLAN applications and Ultra compact antennas using the above techniques and extension of the design to antennas for practical applications like RFID/DVB-H. All the above objectives are thoroughly studied. Antennas with ultra compact dimensions are obtained as a result of the study. Simple equations are provided to design antennas with the required characteristics. The design equations are verified by designing different antennas for different applications.

BROADBAND WIDE COVERAGE UNIPLANAR ANTENNA

The Present thesis deals with the numerical as well as experimental investigations conducted on the resonance and radiation characteristics of Drum shaped monopole antenna, Funnel shaped monopole antenna and the shorted coplanar antenna.An introduction to the over view of antennas, state of the art planar antenna technologies, different feeding techniques and introduction of coplanar waveguides have been discussed.