Methods and Tools for Objective Assessment of Psychomotor Skills in Laparoscopic Surgery

Training and assessment paradigms for laparoscopic surgical skills are evolving from traditional mentor–trainee tutorship towards structured, more objective and safer programs. Accreditation of surgeons requires reaching a consensus on metrics and tasks used to assess surgeons’ psychomotor skills. Ongoing development of tracking systems and software solutions has allowed for the expansion of novel training and assessment means in laparoscopy. The current challenge is to adapt and include these systems within training programs, and to exploit their possibilities for evaluation purposes. This paper describes the state of the art in research on measuring and assessing psychomotor laparoscopic skills. It gives an overview on tracking systems as well as on metrics and advanced statistical and machine learning techniques employed for evaluation purposes. The later ones have a potential to be used as an aid in deciding on the surgical competence level, which is an important aspect when accreditation of the surgeons in particular, and patient safety in general, are considered. The prospective of these methods and tools make them complementary means for surgical assessment of motor skills, especially in the early stages of training. Successful examples such as the Fundamentals of Laparoscopic Surgery should help drive a paradigm change to structured curricula based on objective parameters. These may improve the accreditation of new surgeons, as well as optimize their already overloaded training schedules.

Design and Test of a High QoS Radio Network for CBTC Systems in Subway Tunnels

Communications Based Train Control Systems require high quality radio data communications for train signaling and control. Actually most of these systems use 2.4GHz band with proprietary radio transceivers and leaky feeder as distribution system. All them demand a high QoS radio network to improve the efficiency of railway networks. We present narrow band, broad band and data correlated measurements taken in Madrid underground with a transmission system at 2.4 GHz in a test network of 2 km length in subway tunnels. The architecture proposed has a strong overlap in between cells to improve reliability and QoS. The radio planning of the network is carefully described and modeled with narrow band and broadband measurements and statistics. The result is a network with 99.7% of packets transmitted correctly and average propagation delay of 20ms. These results fulfill the specifications QoS of CBTC systems.

On the specification and testing of inverters for stand-alone PV systems

Inverter features are reviewed from a PV systems perspective, with a view to contributing to possible codes, procurement specifications and testing procedures, in order to assure the technical quality of these systems. A laboratory testing campaign has been carried out on a representative set of sixteen currently available inverters and a set of the most common AC appliances. The results of the tests are discussed with the aim of divulging the particular features of operating AC appliances in PV systems and the provisions to be taken into account in PV system design. The development of testing procedures has followed the motto ?keep it as simple as possible?, in order to make their application easier in conventional laboratories in developing countries.

Conceptual framework for the design, implementation and validation of psychomotor skills’ assessment systems in minimally invasive surgery

Las técnicas de cirugía de mínima invasión (CMI) se están consolidando hoy en día como alternativa a la cirugía tradicional, debido a sus numerosos beneficios para los pacientes. Este cambio de paradigma implica que los cirujanos deben aprender una serie de habilidades distintas de aquellas requeridas en cirugía abierta. El entrenamiento y evaluación de estas habilidades se ha convertido en una de las mayores preocupaciones en los programas de formación de cirujanos, debido en gran parte a la presión de una sociedad que exige cirujanos bien preparados y una reducción en el número de errores médicos. Por tanto, se está prestando especial atención a la definición de nuevos programas que permitan el entrenamiento y la evaluación de las habilidades psicomotoras en entornos seguros antes de que los nuevos cirujanos puedan operar sobre pacientes reales. Para tal fin, hospitales y centros de formación están gradualmente incorporando instalaciones de entrenamiento donde los residentes puedan practicar y aprender sin riesgos. Es cada vez más común que estos laboratorios dispongan de simuladores virtuales o simuladores físicos capaces de registrar los movimientos del instrumental de cada residente. Estos simuladores ofrecen una gran variedad de tareas de entrenamiento y evaluación, así como la posibilidad de obtener información objetiva de los ejercicios. Los diferentes estudios de validación llevados a cabo dan muestra de su utilidad; pese a todo, los niveles de evidencia presentados son en muchas ocasiones insuficientes. Lo que es más importante, no existe un consenso claro a la hora de definir qué métricas son más útiles para caracterizar la pericia quirúrgica. El objetivo de esta tesis doctoral es diseñar y validar un marco de trabajo conceptual para la definición y validación de entornos para la evaluación de habilidades en CMI, en base a un modelo en tres fases: pedagógica (tareas y métricas a emplear), tecnológica (tecnologías de adquisición de métricas) y analítica (interpretación de la competencia en base a las métricas). Para tal fin, se describe la implementación práctica de un entorno basado en (1) un sistema de seguimiento de instrumental fundamentado en el análisis del vídeo laparoscópico; y (2) la determinación de la pericia en base a métricas de movimiento del instrumental. Para la fase pedagógica se diseñó e implementó un conjunto de tareas para la evaluación de habilidades psicomotoras básicas, así como una serie de métricas de movimiento. La validación de construcción llevada a cabo sobre ellas mostró buenos resultados para tiempo, camino recorrido, profundidad, velocidad media, aceleración media, economía de área y economía de volumen. Adicionalmente, los resultados obtenidos en la validación de apariencia fueron en general positivos en todos los grupos considerados (noveles, residentes, expertos). Para la fase tecnológica, se introdujo el EVA Tracking System, una solución para el seguimiento del instrumental quirúrgico basado en el análisis del vídeo endoscópico. La precisión del sistema se evaluó a 16,33ppRMS para el seguimiento 2D de la herramienta en la imagen; y a 13mmRMS para el seguimiento espacial de la misma. La validación de construcción con una de las tareas de evaluación mostró buenos resultados para tiempo, camino recorrido, profundidad, velocidad media, aceleración media, economía de área y economía de volumen. La validación concurrente con el TrEndo® Tracking System por su parte presentó valores altos de correlación para 8 de las 9 métricas analizadas. Finalmente, para la fase analítica se comparó el comportamiento de tres clasificadores supervisados a la hora de determinar automáticamente la pericia quirúrgica en base a la información de movimiento del instrumental, basados en aproximaciones lineales (análisis lineal discriminante, LDA), no lineales (máquinas de soporte vectorial, SVM) y difusas (sistemas adaptativos de inferencia neurodifusa, ANFIS). Los resultados muestran que en media SVM presenta un comportamiento ligeramente superior: 78,2% frente a los 71% y 71,7% obtenidos por ANFIS y LDA respectivamente. Sin embargo las diferencias estadísticas medidas entre los tres no fueron demostradas significativas. En general, esta tesis doctoral corrobora las hipótesis de investigación postuladas relativas a la definición de sistemas de evaluación de habilidades para cirugía de mínima invasión, a la utilidad del análisis de vídeo como fuente de información y a la importancia de la información de movimiento de instrumental a la hora de caracterizar la pericia quirúrgica. Basándose en estos cimientos, se han de abrir nuevos campos de investigación que contribuyan a la definición de programas de formación estructurados y objetivos, que puedan garantizar la acreditación de cirujanos sobradamente preparados y promocionen la seguridad del paciente en el quirófano. Abstract Minimally invasive surgery (MIS) techniques have become a standard in many surgical sub-specialties, due to their many benefits for patients. However, this shift in paradigm implies that surgeons must acquire a complete different set of skills than those normally attributed to open surgery. Training and assessment of these skills has become a major concern in surgical learning programmes, especially considering the social demand for better-prepared professionals and for the decrease of medical errors. Therefore, much effort is being put in the definition of structured MIS learning programmes, where practice with real patients in the operating room (OR) can be delayed until the resident can attest for a minimum level of psychomotor competence. To this end, skills’ laboratory settings are being introduced in hospitals and training centres where residents may practice and be assessed on their psychomotor skills. Technological advances in the field of tracking technologies and virtual reality (VR) have enabled the creation of new learning systems such as VR simulators or enhanced box trainers. These systems offer a wide range of tasks, as well as the capability of registering objective data on the trainees’ performance. Validation studies give proof of their usefulness; however, levels of evidence reported are in many cases low. More importantly, there is still no clear consensus on topics such as the optimal metrics that must be used to assess competence, the validity of VR simulation, the portability of tracking technologies into real surgeries (for advanced assessment) or the degree to which the skills measured and obtained in laboratory environments transfer to the OR. The purpose of this PhD is to design and validate a conceptual framework for the definition and validation of MIS assessment environments based on a three-pillared model defining three main stages: pedagogical (tasks and metrics to employ), technological (metric acquisition technologies) and analytical (interpretation of competence based on metrics). To this end, a practical implementation of the framework is presented, focused on (1) a video-based tracking system and (2) the determination of surgical competence based on the laparoscopic instruments’ motionrelated data. The pedagogical stage’s results led to the design and implementation of a set of basic tasks for MIS psychomotor skills’ assessment, as well as the definition of motion analysis parameters (MAPs) to measure performance on said tasks. Validation yielded good construct results for parameters such as time, path length, depth, average speed, average acceleration, economy of area and economy of volume. Additionally, face validation results showed positive acceptance on behalf of the experts, residents and novices. For the technological stage the EVA Tracking System is introduced. EVA provides a solution for tracking laparoscopic instruments from the analysis of the monoscopic video image. Accuracy tests for the system are presented, which yielded an average RMSE of 16.33pp for 2D tracking of the instrument on the image and of 13mm for 3D spatial tracking. A validation experiment was conducted using one of the tasks and the most relevant MAPs. Construct validation showed significant differences for time, path length, depth, average speed, average acceleration, economy of area and economy of volume; especially between novices and residents/experts. More importantly, concurrent validation with the TrEndo® Tracking System presented high correlation values (>0.7) for 8 of the 9 MAPs proposed. Finally, the analytical stage allowed comparing the performance of three different supervised classification strategies in the determination of surgical competence based on motion-related information. The three classifiers were based on linear (linear discriminant analysis, LDA), non-linear (support vector machines, SVM) and fuzzy (adaptive neuro fuzzy inference systems, ANFIS) approaches. Results for SVM show slightly better performance than the other two classifiers: on average, accuracy for LDA, SVM and ANFIS was of 71.7%, 78.2% and 71% respectively. However, when confronted, no statistical significance was found between any of the three. Overall, this PhD corroborates the investigated research hypotheses regarding the definition of MIS assessment systems, the use of endoscopic video analysis as the main source of information and the relevance of motion analysis in the determination of surgical competence. New research fields in the training and assessment of MIS surgeons can be proposed based on these foundations, in order to contribute to the definition of structured and objective learning programmes that guarantee the accreditation of well-prepared professionals and the promotion of patient safety in the OR.

Analysis and design of multiagent systems using MAS-CommonKADS

This article proposes an agent-oriented methodology called MAS-CommonKADS and develops a case study. This methodology extends the knowledge engineering methodology CommonKADSwith techniquesfrom objectoriented and protocol engineering methodologies. The methodology consists of the development of seven models: Agent Model, that describes the characteristics of each agent; Task Model, that describes the tasks that the agents carry out; Expertise Model, that describes the knowledge needed by the agents to achieve their goals; Organisation Model, that describes the structural relationships between agents (software agents and/or human agents); Coordination Model, that describes the dynamic relationships between software agents; Communication Model, that describes the dynamic relationships between human agents and their respective personal assistant software agents; and Design Model, that refines the previous models and determines the most suitable agent architecture for each agent, and the requirements of the agent network.

Detection and Isolation of Simultaneous Additive and Parametric Faults in Nonlinear Stochastic Dynamical Systems

This paper presents a new fault detection and isolation scheme for dealing with simultaneous additive and parametric faults. The new design integrates a system for additive fault detection based on Castillo and Zufiria, 2009 and a new parametric fault detection and isolation scheme inspired in Munz and Zufiria, 2008 . It is shown that the so far existing schemes do not behave correctly when both additive and parametric faults occur simultaneously; to solve the problem a new integrated scheme is proposed. Computer simulation results are presented to confirm the theoretical studies.

Real time passenger information systems and quality of bus services

One of the main problems in urban areas is the steady growth in car ownership and traffic levels. Therefore, the challenge of sustainability is focused on a shift of the demand for mobility from cars to collective means of transport. For this end, buses are a key element of the public transport systems. In this respect Real Time Passenger Information (RTPI) systems help citizens change their travel behaviour towards more sustainable transport modes. This paper provides an assessment methodology which evaluates how RTPI systems improve the quality of bus services in two European cities, Madrid and Bremerhaven. In the case of Madrid, bus punctuality has increased by 3%. Regarding the travellers perception, Madrid raised its quality of service by 6% while Bremerhaven increased by 13%. On the other hand, the users ́ perception of Public Transport (PT) image increased by 14%.

Ontology driven description and engineering of autonomous systems: application to process system engineering

Autonomous systems refer to systems capable of operating in a real world environment without any form of external control for extended periods of time. Autonomy is a desired goal for every system as it improves its performance, safety and profit. Ontologies are a way to conceptualize the knowledge of a specific domain. In this paper an ontology for the description of autonomous systems as well as for its development (engineering) is presented and applied to a process. This ontology is intended to be applied and used to generate final applications following a model driven methodology.

Quality assurance systems in the production and marketing of fresh peaches.

Due to the fast rate of peach post-harvest ripening, damage due to mechanical handling, externally appreciated as bruises and soft areas, is a real problem that leads to an early harvesting and poor quality of the fruits, as perceived by the consumers. More and more, the European consumer asks for good taste and freshness of fruits and vegetables, and these quality factors are not included in standards, nor in most of the producers' practices. Fruit processing and marketing centres (co-operatives) are increasingly interested in adopting quality controls in their processes. ISO 9000 procedures are being applied in some food areas, primarily milk and meat processors, but no generalised procedures have been developed until the present time to be applied to fresh product processes. All different peach and nectarine varieties that are harvested and handled in Murcia cooperatives and sold in a large supermarket in Madrid were analysed during the whole 1997 season (early May to late August). A total number of 78 samples of 25 fruits (co-operative) or 10 fruits (market), were tested in the laboratory for mechanical, optical, chemical and tasting quality. The variability and relationships between all these quality parameters are presented and discussed, and sampling unit sizes which would be advisable for quality control are calculated.

NGCPV: a new generation of concentrator photovoltaic cells, modules and systems

Starting on June 2011, NGCPV is the first project funded jointly between the European Commission (EC) and the New Energy and Industrial Technology Development Organization (NEDO) of Japan to research on new generation concentration photovoltaics (CPV). The Project, through a collaborative research between seven European and nine Japanese leading research centers in the field of CPV, aims at lowering the cost of the CPVproduced photovoltaic kWh down to 5 ?cents. The main objective of the project is to improve the present concentrator cell, module and system efficiency, as well as developing advanced characterization tools for CPV components and systems. As particular targets, the project aims at achieving a cell efficiency of at least 45% and a CPV module with an efficiency greater than 35%. This paper describes the R&D activities that are being carried out within the NGCPV project and summarizes some of the most relevant results that have already been attained, for instance: the manufacturing of a 44.4% world record efficiency triple junction solar cell (by Sharp Corp.) and the installation of a 50 kWp experimental CPV plant in Spain, which will be used to obtain accurate forecasts of the energy produced at system level.

Digital libraries for the preservation of research methods and associated artifacts

New digital artifacts are emerging in data-intensive science. For example, scientific workflows are executable descriptions of scientific procedures that define the sequence of computational steps in an automated data analysis, supporting reproducible research and the sharing and replication of best-practice and know-how through reuse. Workflows are specified at design time and interpreted through their execution in a variety of situations, environments, and domains. Hence it is essential to preserve both their static and dynamic aspects, along with the research context in which they are used. To achieve this, we propose the use of multidimensional digital objects (Research Objects) that aggregate the resources used and/or produced in scientific investigations, including workflow models, provenance of their executions, and links to the relevant associated resources, along with the provision of technological support for their preservation and efficient retrieval and reuse. In this direction, we specified a software architecture for the design and implementation of a Research Object preservation system, and realized this architecture with a set of services and clients, drawing together practices in digital libraries, preservation systems, workflow management, social networking and Semantic Web technologies. In this paper, we describe the backbone system of this realization, a digital library system built on top of dLibra.

Modelling and Control of Stepper Motors for High Accuracy Positioning Systems Used in Radioactive Environments

Hybrid Stepper Motors are widely used in open-loop position applications. They are the choice of actuation for the collimators in the Large Hadron Collider, the largest particle accelerator at CERN. In this case the positioning requirements and the highly radioactive operating environment are unique. The latter forces both the use of long cables to connect the motors to the drives which act as transmission lines and also prevents the use of standard position sensors. However, reliable and precise operation of the collimators is critical for the machine, requiring the prevention of step loss in the motors and maintenance to be foreseen in case of mechanical degradation. In order to make the above possible, an approach is proposed for the application of an Extended Kalman Filter to a sensorless stepper motor drive, when the motor is separated from its drive by long cables. When the long cables and high frequency pulse width modulated control voltage signals are used together, the electrical signals difer greatly between the motor and drive-side of the cable. Since in the considered case only drive-side data is available, it is therefore necessary to estimate the motor-side signals. Modelling the entire cable and motor system in an Extended Kalman Filter is too computationally intensive for standard embedded real-time platforms. It is, in consequence, proposed to divide the problem into an Extended Kalman Filter, based only on the motor model, and separated motor-side signal estimators, the combination of which is less demanding computationally. The efectiveness of this approach is shown in simulation. Then its validity is experimentally demonstrated via implementation in a DSP based drive. A testbench to test its performance when driving an axis of a Large Hadron Collider collimator is presented along with the results achieved. It is shown that the proposed method is capable of achieving position and load torque estimates which allow step loss to be detected and mechanical degradation to be evaluated without the need for physical sensors. These estimation algorithms often require a precise model of the motor, but the standard electrical model used for hybrid stepper motors is limited when currents, which are high enough to produce saturation of the magnetic circuit, are present. New model extensions are proposed in order to have a more precise model of the motor independently of the current level, whilst maintaining a low computational cost. It is shown that a significant improvement in the model It is achieved with these extensions, and their computational performance is compared to study the cost of model improvement versus computation cost. The applicability of the proposed model extensions is demonstrated via their use in an Extended Kalman Filter running in real-time for closed-loop current control and mechanical state estimation. An additional problem arises from the use of stepper motors. The mechanics of the collimators can wear due to the abrupt motion and torque profiles that are applied by them when used in the standard way, i.e. stepping in open-loop. Closed-loop position control, more specifically Field Oriented Control, would allow smoother profiles, more respectful to the mechanics, to be applied but requires position feedback. As mentioned already, the use of sensors in radioactive environments is very limited for reliability reasons. Sensorless control is a known option but when the speed is very low or zero, as is the case most of the time for the motors used in the LHC collimator, the loss of observability prevents its use. In order to allow the use of position sensors without reducing the long term reliability of the whole system, the possibility to switch from closed to open loop is proposed and validated, allowing the use of closed-loop control when the position sensors function correctly and open-loop when there is a sensor failure. A different approach to deal with the switched drive working with long cables is also presented. Switched mode stepper motor drives tend to have poor performance or even fail completely when the motor is fed through a long cable due to the high oscillations in the drive-side current. The design of a stepper motor output fillter which solves this problem is thus proposed. A two stage filter, one devoted to dealing with the diferential mode and the other with the common mode, is designed and validated experimentally. With this ?lter the drive performance is greatly improved, achieving a positioning repeatability even better than with the drive working without a long cable, the radiated emissions are reduced and the overvoltages at the motor terminals are eliminated.

Review and comparison of effective delayed neutron fraction calculation methods with Monte Carlo codes

The calculation of the effective delayed neutron fraction, beff , with Monte Carlo codes is a complex task due to the requirement of properly considering the adjoint weighting of delayed neutrons. Nevertheless, several techniques have been proposed to circumvent this difficulty and obtain accurate Monte Carlo results for beff without the need of explicitly determining the adjoint flux. In this paper, we make a review of some of these techniques; namely we have analyzed two variants of what we call the k-eigenvalue technique and other techniques based on different interpretations of the physical meaning of the adjoint weighting. To test the validity of all these techniques we have implemented them with the MCNPX code and we have benchmarked them against a range of critical and subcritical systems for which either experimental or deterministic values of beff are available. Furthermore, several nuclear data libraries have been used in order to assess the impact of the uncertainty in nuclear data in the calculated value of beff .

Development of somatic embryogenesis for cloning and conservation of mature holm oak trees (Quercus ilex L.)

La encina (Quercus ilex L.) es una de las especies forestales mediterráneas más importantes. Constituye gran parte del estrato arbóreo de dehesas o montados, produce bellota como alimento del ganado y establece simbiosis con hongos micorrizógenos de gran valor económico. La encina está considerada como una especie recalcitrante en términos de conservación de semillas y capacidad morfogénica, lo que dificulta los programas de conservación de recursos genéticos y la mejora de la especie. La propagación vegetativa es una potente herramienta de los programas de mejora, por lo que es preciso desarrollar protocolos de regeneración somática en encina. La embriogénesis somática está considerada como la modalidad más adecuada de regeneración basada en técnicas de cultivo de tejidos vegetales utilizada en biotecnología forestal. Este trabajo se centra en el estudio de determinados aspectos de la embriogénesis somática para la regeneración clonal de encinas adultas. La memoria de esta tesis se ha dividido en capítulos que se corresponden con diferentes aspectos del sistema embriogénico. La embriogénesis somática se indujo en tegumentos maternos de óvulos en desarrollo procedentes de bellotas inmaduras de encinas adultas. A pesar de las bajas frecuencias de inducción, las líneas embriogénicas generadas se amplificaron mediante embriogénesis secundaria observándose cierta pérdida de la capacidad de diferenciación con el tiempo. Tanto el genotipo como la formulación del medio de cultivo influyeron en la respuesta embriogénica, concluyendo que la formulación de macronutrientes de Schenk y Hildebrant del medio sin reguladores de crecimiento fue la combinación más efectiva en la inducción. Los resultados sugirieron la existencia de una ventana en el desarrollo del óvulo más sensible a la inducción. El genotipo in[luyó en la capacidad proliferativa de los cultivos y en la conversión de los embriones somáticos, que se incrementó suplementando el medio con ácido indol-3-butírico y 6-benciladenina. El cultivo en medio líquido de líneas embriogénicas en condiciones de inmersión transitoria incrementó el crecimiento, dependiendo del genotipo, con respecto al cultivo en medio semisólido. Sin embargo, no mejoró la capacidad de diferenciar embriones cotiledonares aislados. Se estableció un protocolo de inicio y mantenimiento de cultivos en suspensión para varias líneas embriogénicas mediante inoculación en alta densidad de agregados embrionarios procedentes del medio semisólido. Para evitar la pérdida de vigor y la capacidad morfogénica debida al cultivo prolongado se desarrolló un protocolo de crioconservación de líneas embriogénicas mediante vitrificación. Al determinar la influencia de los agentes crioprotectores antes y después de su inmersión en nitrógeno líquido se concluyó que las respuestas de capacidad de crecimiento y de diferenciación del material embriogénico son independientes, además de estar bajo influencia del genotipo y el tipo de material crioconservado. La combinación de sacarosa y PVS2 previa a la inmersión en nitrógeno líquido proporcionó la mayor tasa de recuperación. Cuando las líneas fueron crioconservadas 30 días la capacidad de diferenciación se perdió en todas ellas. El análisis de SSR detectó variación somaclonal en el material crioconservado a corto plazo. SSR y RAPD mostraron importantes diferencias genéticas entre los árboles donantes y el material embriogénico que dependieron del genotipo. El grado de detección dependió del marcador empleado. Ambos marcadores revelaron baja inestabilidad intraclonal. Los RAPD revelaron variación genética intra-individuo en las encinas donantes. Se discuten la variación genética pre-existente en encina, su aparición durante las primeras fases de la inducción de embriogénesis, y la presencia de tejidos provenientes de la fertilización en el explanto materno. Esto hace preciso definir la identidad genética del material donante y acometer ensayos de detección precoz de variación somaclonal. ABSTRACT Holm oak (Quercus ilex L.) is one of the most important Mediterranean forest species. It conforms the tree layer of dehesas or montados, it produces acorns to feed the livestock and it establishes symbiosis with profitable mycorrhizal fungi. Holm oak is considered as recalcitrant species in terms of seed conservation and morphogenic capacities, which complicates the development of genetic conservation and improvement programs. Vegetative propagation is one of the mightiest tools for breeding programs therefore; developing protocols for clonal regeneration of holm oak is essential. Somatic embryogenesis is considered the best tissue culture-based way of plant regeneration in forest biotechnology. The present study is focused on the study of certain aspects of somatic embryogenesis for clonal regeneration of mature holm oak. This thesis manuscript is divided into several chapters that match with different aspects of the embryogenic system. Somatic embryogenesis induction was achieved on maternal teguments of developing ovules from immature acorns of adult holm oak trees. Despite the low induction frequencies, the generated embryogenic lines were amplified by secondary embryogenesis. A decline in the differentiation capacity over time was also observed. It was concluded that both genotype and culture media formulation influenced the embryogenic response, being the Schenk and Hildebrandt´s macronutrients formulation from culture medium and the lack of plant growth regulators the most effective combination for the induction of the embryogenic response. It has been suggested the existence of a developmental window in which ovules are prone to induction. Genotype influenced the proliferation capacity and the plant conversion of somatic embryos, which was also favoured by the presence of indol-3-butyric acid and 6-bencyladenine. The use of temporary immersion systems as proliferation in liquid culture of the embryogenic lines increased the growth depending on genotype, when compared to semisolid cultures. However, it did not improve the differentiation of single cotyledonary embryos. A protocol for the initiation and maintenance of embryogenic suspension cultures was established for several embryogenic lines with highly dense inoculi of embryogenic clusters from proliferating semisolid cultures. In order to avoid the loss of vigour and morphogenic ability of embryogenic lines due to prolonged cultures, a cryopreservation protocol for embryogenic lines of holm oak has been developed. During the determination of the influence of cryoprotective agents on the growth and differentiation capacities before and after liquid nitrogen immersion, it was concluded that both responses were independent from each other and also under the influence of genotype and the type of cryopreserved material. The combination of sucrose and PVS2 prior liquid nitrogen immersion provided higher recovery rates. When the same embryogenic lines were cryopreserved for 30 days, none was able to differentiate. The SSRs analysis of the short-term cryopreserved material detected somaclonal variation. Both SSR and RAPD markers showed high sensitivity to detect genetic differences between the donor trees and the generated embryogenic material. Nevertheless, the degree of instability detection depended on the marker. The SSR analysis indicated a relationship between genotype, the studied loci and the located polymorphisms. Also, both markers revealed low intraclonal genetic variation. The RAPD detected genetic variation within the donor trees. The presence of pre-existent genetic variation within mature trees, in addition to its occurrence during the early stages of the embryogenic induction, and the presence of tissues of fertilisation origin within the maternal explants are all discussed. Nonetheless, the determination of the genetic identity of donor material is required, in addition to early detection methods of somaclonal variation.

Development of somatic embryogenesis for cloning and conservation of mature holm oak trees (Quercus ilex L.)

La encina (Quercus ilex L.) es una de las especies forestales mediterráneas más importantes. Constituye gran parte del estrato arbóreo de dehesas o montados, produce bellota como alimento del ganado y establece simbiosis con hongos micorrizógenos de gran valor económico. La encina está considerada como una especie recalcitrante en términos de conservación de semillas y capacidad morfogénica, lo que dificulta los programas de conservación de recursos genéticos y la mejora de la especie. La propagación vegetativa es una potente herramienta de los programas de mejora, por lo que es preciso desarrollar protocolos de regeneración somática en encina. La embriogénesis somática está considerada como la modalidad más adecuada de regeneración basada en técnicas de cultivo de tejidos vegetales utilizada en biotecnología forestal. Este trabajo se centra en el estudio de determinados aspectos de la embriogénesis somática para la regeneración clonal de encinas adultas. La memoria de esta tesis se ha dividido en capítulos que se corresponden con diferentes aspectos del sistema embriogénico. La embriogénesis somática se indujo en tegumentos maternos de óvulos en desarrollo procedentes de bellotas inmaduras de encinas adultas. A pesar de las bajas frecuencias de inducción, las líneas embriogénicas generadas se amplificaron mediante embriogénesis secundaria observándose cierta pérdida de la capacidad de diferenciación con el tiempo. Tanto el genotipo como la formulación del medio de cultivo influyeron en la respuesta embriogénica, concluyendo que la formulación de macronutrientes de Schenk y Hildebrant del medio sin reguladores de crecimiento fue la combinación más efectiva en la inducción. Los resultados sugirieron la existencia de una ventana en el desarrollo del óvulo más sensible a la inducción. El genotipo in[luyó en la capacidad proliferativa de los cultivos y en la conversión de los embriones somáticos, que se incrementó suplementando el medio con ácido indol-3-butírico y 6-benciladenina. El cultivo en medio líquido de líneas embriogénicas en condiciones de inmersión transitoria incrementó el crecimiento, dependiendo del genotipo, con respecto al cultivo en medio semisólido. Sin embargo, no mejoró la capacidad de diferenciar embriones cotiledonares aislados. Se estableció un protocolo de inicio y mantenimiento de cultivos en suspensión para varias líneas embriogénicas mediante inoculación en alta densidad de agregados embrionarios procedentes del medio semisólido. Para evitar la pérdida de vigor y la capacidad morfogénica debida al cultivo prolongado se desarrolló un protocolo de crioconservación de líneas embriogénicas mediante vitrificación. Al determinar la influencia de los agentes crioprotectores antes y después de su inmersión en nitrógeno líquido se concluyó que las respuestas de capacidad de crecimiento y de diferenciación del material embriogénico son independientes, además de estar bajo influencia del genotipo y el tipo de material crioconservado. La combinación de sacarosa y PVS2 previa a la inmersión en nitrógeno líquido proporcionó la mayor tasa de recuperación. Cuando las líneas fueron crioconservadas 30 días la capacidad de diferenciación se perdió en todas ellas. El análisis de SSR detectó variación somaclonal en el material crioconservado a corto plazo. SSR y RAPD mostraron importantes diferencias genéticas entre los árboles donantes y el material embriogénico que dependieron del genotipo. El grado de detección dependió del marcador empleado. Ambos marcadores revelaron baja inestabilidad intraclonal. Los RAPD revelaron variación genética intra-individuo en las encinas donantes. Se discuten la variación genética pre-existente en encina, su aparición durante las primeras fases de la inducción de embriogénesis, y la presencia de tejidos provenientes de la fertilización en el explanto materno. Esto hace preciso definir la identidad genética del material donante y acometer ensayos de detección precoz de variación somaclonal. ABSTRACT Holm oak (Quercus ilex L.) is one of the most important Mediterranean forest species. It conforms the tree layer of dehesas or montados, it produces acorns to feed the livestock and it establishes symbiosis with profitable mycorrhizal fungi. Holm oak is considered as recalcitrant species in terms of seed conservation and morphogenic capacities, which complicates the development of genetic conservation and improvement programs. Vegetative propagation is one of the mightiest tools for breeding programs therefore; developing protocols for clonal regeneration of holm oak is essential. Somatic embryogenesis is considered the best tissue culture-based way of plant regeneration in forest biotechnology. The present study is focused on the study of certain aspects of somatic embryogenesis for clonal regeneration of mature holm oak. This thesis manuscript is divided into several chapters that match with different aspects of the embryogenic system. Somatic embryogenesis induction was achieved on maternal teguments of developing ovules from immature acorns of adult holm oak trees. Despite the low induction frequencies, the generated embryogenic lines were amplified by secondary embryogenesis. A decline in the differentiation capacity over time was also observed. It was concluded that both genotype and culture media formulation influenced the embryogenic response, being the Schenk and Hildebrandt´s macronutrients formulation from culture medium and the lack of plant growth regulators the most effective combination for the induction of the embryogenic response. It has been suggested the existence of a developmental window in which ovules are prone to induction. Genotype influenced the proliferation capacity and the plant conversion of somatic embryos, which was also favoured by the presence of indol-3-butyric acid and 6-bencyladenine. The use of temporary immersion systems as proliferation in liquid culture of the embryogenic lines increased the growth depending on genotype, when compared to semisolid cultures. However, it did not improve the differentiation of single cotyledonary embryos. A protocol for the initiation and maintenance of embryogenic suspension cultures was established for several embryogenic lines with highly dense inoculi of embryogenic clusters from proliferating semisolid cultures. In order to avoid the loss of vigour and morphogenic ability of embryogenic lines due to prolonged cultures, a cryopreservation protocol for embryogenic lines of holm oak has been developed. During the determination of the influence of cryoprotective agents on the growth and differentiation capacities before and after liquid nitrogen immersion, it was concluded that both responses were independent from each other and also under the influence of genotype and the type of cryopreserved material. The combination of sucrose and PVS2 prior liquid nitrogen immersion provided higher recovery rates. When the same embryogenic lines were cryopreserved for 30 days, none was able to differentiate. The SSRs analysis of the short-term cryopreserved material detected somaclonal variation. Both SSR and RAPD markers showed high sensitivity to detect genetic differences between the donor trees and the generated embryogenic material. Nevertheless, the degree of instability detection depended on the marker. The SSR analysis indicated a relationship between genotype, the studied loci and the located polymorphisms. Also, both markers revealed low intraclonal genetic variation. The RAPD detected genetic variation within the donor trees. The presence of pre-existent genetic variation within mature trees, in addition to its occurrence during the early stages of the embryogenic induction, and the presence of tissues of fertilisation origin within the maternal explants are all discussed. Nonetheless, the determination of the genetic identity of donor material is required, in addition to early detection methods of somaclonal variation.