Material response and failure mechanism of unidirectional metal matrix composites under impulsive shear loading

The material response and failure mechanism of unidirectional metal matrix composite under impulsive shear loading are investigated in this paper. Both experimental and analytical studies were performed. The shear strength of unidirectional C-f/A356.0 composite and A356.0 aluminum alloy at high strain rate were measured with a modified split Hopkinson torsional bar technique. The results indicated that the carbon fibers did not improve the shear strength of aluminum matrix if the fiber orientation aligned with the shear loading axis. The microscopic inspection of the fractured surface showed a multi-scale zigzag feature which implied a complicated shear failure mechanism in the composite. In addition to testing, the micromechanical stress field in the composite was analyzed by the generalized Eshelby equivalent method (GEEM). The influence of cracking in matrix on the micromechanical stress field was investigated as well. The results showed that the stress distribution in the composite is quite nonhomogeneous and very high shear stress concentrations are found in some regions in the matrix. The high shear stress concentration in the matrix induces tensile cracking at 45 degrees to the shear direction. This in turn aggravates the stress concentration at the fiber/matrix interface and finally leads to a catastrophic failure in the composite. From the correlation between the analysis and experimental results, the shear failure mechanism of unidirectional C-f/A356.0 composite can be elucidated qualitatively.

Experimental Studies of the Material Properties of the Forewing of Cicada (Homoptera, Cicadidae)

Detailed investigations on the structural and mechanical properties of the forewing of the cicada were carried out. Measurement of the structures of the wings showed that the thickness of the membrane of each cell and the diameter of each vein were non-uniform in both the longitudinal and transverse directions, and their means were approximately 12.2 and 133.3 mum, respectively. However, the aspect ratios of the wings and the bodies were quite uniform and were approximately equal to 2.98 and 2.13, respectively. Based on the measured thickness, mass and area of the membranes of the cells, the mean density and the mean area density of the wing were approximately 2.3 g cm(-3) and 2.8 x 10(-3) g cm(-2), respectively. In addition, the diameters of the veins of the wings, including the diameters of the holes in the vein of the leading edge, were examined. The mechanical properties of the wing were investigated separately by nanoindentation and tensile testing. The results indicated that the mean Young's modulus, hardness and yield stress of the membranes of the wings were approximately 3.7 Gpa, 0.2 Gpa and 29 Mpa, respectively, and the mean Young's modulus and strength of the veins along the direction of the venation of wings were approximately 1.9 Gpa and 52 Mpa, respectively. Finally, the relevant results were briefly analyzed and discussed, providing a guideline to the biomimetic design of the aerofoil materials of micro air vehicles.

Determination of Proper Processing Conditions of Material Surface Heat Treatment Through Finite Element Method

A two-dimensional model has been developed based on the experimental results of stainless steel remelting with the laminar plasma technology to investigate the transient thermo-physical characteristics of the melt pool liquids. The influence of the temperature field, temperature gradient, solidification rate and cooling rate on the processing conditions has been investigated numerically. Not only have the appropriate processing conditions been determined according to the calculations, but also they have been predicted with a criterion established based on the concept of equivalent temperature area density (ETAD) that is actually a function of the processing parameters and material properties. The comparison between the resulting conditions shows that the ETAD method can better predict the optimum condition.

Influences of strain rate and temperature variation on material intrinsic length of plasticity strain gradient theory

Cowper-Symonds and Johnson-Cook dynamic constitutive relations are used to study the influence of both strain rate effect and temperature variation on the material intrinsic length scale in strain gradient plasticity. The material intrinsic length scale decreases with increasing strain rates, and this length scale increases with temperature.

Comparación de calidad en la producción de carbón vegetal entre la fosa de tierra y el horno de ladrillo, en la finca el plantel Masaya

La presente investigación tuvo como objetivo comparar la producción de calidad de carbón vegetal entre la fosa de tierra y el horno de ladrillo utilizando Eucalyptus camaldulensis, empleando dos categorías diamétricas. La metodología utilizada consistió en la selección del material vegetal para la producción de carbón, se seleccionaron árboles con diámetros entre 20-30 cm. y mayores de 30 cm. por cada categoría diamétrica se emplearon cinco árboles para un total de diez individuos, se tumbaron los árboles con la técnica de tala dirigida, con hacha a partir de 0.30 cm. del suelo con el propósito de aprovechar la mayor cantidad de madera del árbol, se procedió a medir la longitud de la troza en metros empleando una cinta métrica para la medición del diámetro medio. Luego se procedió a calcular el volumen del fuste limpio utilizando la fórmula de Smalian, posteriormente se traslado trozas y ramas al sitio de carbonización, se depositaron por clase diamétrica donde se cálculo el volumen empleando la fórmula de Huber, para la cubicación de las ramas se empleo el método tradicional de metro estéreo. Para la producción de carbón vegetal se emplearon dos diseños de producción: fosa de tierra y el horno de ladrillos, el análisis de laboratorio consistió en determinar porcentaje de cenizas, carbono orgánico, densidad aparente y porcentaje de humedad. Para la clase diamétrica de 20 a 30 cm., se utilizo un volumen de 4.48 m3 y para la categoría diamétrica mayor de 30 cm, 6.55 m3. Finalizado el proceso de carbonización se obtuvieron 8 sacos en la fosa de tierra, equivalente a 0.217m3, en el horno de ladrillo se obtuvieron 18 sacos lo que representa 0.496 m3. Comparando los estándares de calidad de la FAO, con los obtenidos en este estudio, son aceptables, se concluye que el método de producción de horno de ladrillos usando arboles mayores de 30 cm es el mejor método para la producción de carbón vegetal.

Evaluación del comportamiento de falso roble (Tabebuia rosea (Bertol.) DC.), Genízaro (Pithecellobium saman (Jacq.) Benth.) y Guanacaste negro (Enterolobium cyclocarpum (Jacq.) Griseb.) en ensayo de germinación y sembrados en dos tipos de sustrato orgánico

Las etapas de este trabajo de investigación se llevaron a cabo en las instalaciones del invernadero y vivero de la Universidad Nacional Agraria, ubicada a la altura del kilómetro 12 carretera norte en la ciudad de Managua. Se realizó un ensayo de germinación con semillas falso roble Tabebuia rosea (Bertol.) DC., genízaro Phitecellobium saman (Jacq.) Benth. y guanacaste negro Enterolobium cyclocarpum (Jacq.) Griseb., para cuantificar el porcentaje, energía y valor de la germinación aplicando tratamientos pre germinativos. Posteriormente, en vivero, se establecieron dichas especies en un diseño de bloques completos al azar con tres bloques por especie, tres tratamientos por bloque y noventa repeticiones por tratamiento, realizando un ANDEVA y aplicando una prueba de separación de medias. Las variables evaluadas en el ANDEVA fueron altura total y diámetro basal. Separadamente se evaluó la mortalidad y sobrevivencia de las plantas en el vivero. El tratamiento pre germinativo que dio mejores resultados fue el rompimiento de la testa en el extremo donde se encuentra el micrópilo, con porcentajes de germinación superiores al 90%. No se encontraron diferencias significativas entre tratamientos, por lo cual no hubo efecto de los sustratos sobre los incrementos de las plantas de genízaro Phitecellobium saman (Jacq.) Benth. y se encontraron diferencias significativas entre tratamientos y variables para guanancaste negro Enterolobium cyclocarpum (Jacq.) Griseb. con los mayores incrementos en compostaje con 29,32 cm y los menores en tierra común 18,82 cm. El compostaje fue el sustrato donde ocurrió la mayor sobrevivencia de guanacaste negro Phitecellobium saman (Jacq.) Benth. con 85% y genízaro Phitecellobium saman (Jacq.) Benth. con 66%. Los valores de mortalidad fueron menores al 26% en todos los sustratos.

Three-Dimensional Modeling of Heat Transfer and Fluid Flow in Laminar-Plasma Material Re-Melting Processing

Modeling study is performed concerning the heat transfer and fluid flow for a laminar argon plasma jet impinging normally upon a flat workpiece exposed to the ambient air. The diffusion of the air into the plasma jet is handled by using the combined-diffusion-coefficient approach. The heat flux density and jet shear stress distributions at the workpiece surface obtained from the plasma jet modeling are then used to study the re-melting process of a carbon steel workpiece. Besides the heat conduction within the workpiece, the effects of the plasma-jet inlet parameters (temperature and velocity), workpiece moving speed, Marangoni convection, natural convection etc. on the re-melting process are considered. The modeling results demonstrate that the shapes and sizes of the molten pool in the workpiece are influenced appreciably by the plasma-jet inlet parameters, workpiece moving speed and Marangoni convection. The jet shear stress manifests its effect at higher plasma-jet inlet velocities, while the natural convection effect can be ignored. The modeling results of the molten pool sizes agree reasonably with available experimental data.

Evolution induced catastrophe in a nonlinear dynamical model of material failure

In order to study the failure of disordered materials, the ensemble evolution of a nonlinear chain model was examined by using a stochastic slice sampling method. The following results were obtained. (1) Sample-specific behavior, i.e. evolutions are different from sample to sample in some cases under the same macroscopic conditions, is observed for various load-sharing rules except in the globally mean field theory. The evolution according to the cluster load-sharing rule, which reflects the interaction between broken clusters, cannot be predicted by a simple criterion from the initial damage pattern and even then is most complicated. (2) A binary failure probability, its transitional region, where globally stable (GS) modes and evolution-induced catastrophic (EIC) modes coexist, and the corresponding scaling laws are fundamental to the failure. There is a sensitive zone in the vicinity of the boundary between the GS and EIC regions in phase space, where a slight stochastic increment in damage can trigger a radical transition from GS to EIC. (3) The distribution of strength is obtained from the binary failure probability. This, like sample-specificity, originates from a trans-scale sensitivity linking meso-scopic and macroscopic phenomena. (4) Strong fluctuations in stress distribution different from that of GS modes may be assumed as a precursor of evolution-induced catastrophe (EIC).

The effect of nucleation time on the growth of a microvoid in a viscoelastic material

In this paper, discussions are focused on the growth of a nucleated void in a viscoelastic material. The in situ tensile tests of specimens made of high-density polyethylene, filled with spherical glass beads (HDPE/GB) are carried out under SEM. The experimental result indicates that the microvoid nucleation is induced by the partially interfacial debonding of particles. By means of the Laplace transform and the Eshelby's equivalent inclusion method, a new analytical expression of the void strain at different nucleation times is derived. It can be seen that the strain of the nucleated void depends not only on the remote strain history, but also on the nucleation time. This expression is also illustrated by numerical examples, and is found to be of great usefulness in the study of damage evolution in viscoelastic materials.

Dynamic stress intensity factor of a functionally graded material under antiplane shear loading

The dynamic response of a finite crack in an unbounded Functionally Graded Material (FGM) subjected to an antiplane shear loading is studied in this paper. The variation of the shear modulus of the functionally graded material is modeled by a quadratic increase along the direction perpendicular to the crack surface. The dynamic stress intensity factor is extracted from the asymptotic expansion of the stresses around the crack tip in the Laplace transform plane and obtained in the time domain by a numerical Laplace inversion technique. The influence of graded material property on the dynamic intensity factor is investigated. It is observed that the magnitude of dynamic stress intensity factor for a finite crack in such a functionally graded material is less than in the homogeneous material with a property identical to that of the FGM crack plane.

Material parameter extraction in THz-TDS using a converging beam transfer function

We demonstrate a parameter extraction algorithm based on a theoretical transfer function, which takes into account a converging THz beam. Using this, we successfully extract material parameters from data obtained for a quartz sample with a THz time domain spectrometer. © 2010 IEEE.