Scanning electron microscopy of the corneal endothelium of ostrich

The aim of this study was to examine the endothelial surface morphology and perform a morphometric analysis of the corneal endothelial cells of ostrich (Struthio camelus) using scanning electron microscopy. Polygonality, mean cell area, cell density and coefficient of variation of mean cell area were analyzed. The normal corneal endothelium consisted of polygonal cells of uniform size and shape with few interdigitations of the cell borders. Microvilli appeared as protusions on the cellular surface. The average cell area was 269±18µm² and the endothelial cell density was 3717±240cells mm-2. The coefficient of variation of the cell area was 0.06, and the percentage of hexagonal cells was 75%. The parameters evaluated did not differ significantly between the right and the left eye from the same ostrich. The results of this study showed that the ostrich corneal endothelial cells appear quite similar to those of the other vertebrates.

Efeito da inclusão de diferentes fontes lipídicas e óleo mineral na dieta sobre a digestibilidade dos nutrientes e os níveis plasmáticos de gordura em equinos

Objetivou-se avaliar os efeitos da inclusão de gordura de origem animal ou vegetal e de óleo mineral sobre a aceitabilidade, a digestibilidade dos nutrientes e as concentrações plasmáticas de triglicérides e colesterol em equinos. Utilizaram-se quatro potros de 13 a 16 meses de idade recebendo dieta contendo feno de gramínea e concentrado, em delineamento quadrado latino, analisado por contrastes ortogonais. A aceitabilidade não foi influenciada pela quantidade nem pelo tipo de óleo adicionado às dietas. Os menores valores de digestibilidade de matéria seca (MS), matéria orgânica (MO) e extrato etéreo (EE) foram observados para as dietas acrescidas de óleo mineral (58,90; 60,29 e 32,02%) em comparação à dieta controle, cujos valores foram de 62,58; 64,41 e 77,72%. O coeficiente de digestibilidade do EE obtido com a dieta com óleo mineral foi menor (32,02%) que o obtido para as dietas com gordura animal (90,26%) e gordura vegetal (86,47%). A dieta com óleo mineral reduziu a concentração de HDL-C (68,75 mg/dL) em relação à dieta controle (76,00 mg/dL). A adição de fontes lipídicas e óleo mineral não influencia na aceitabilidade da dieta por equinos. O óleo vegetal não se diferencia da gordura animal quanto à digestibilidade dos nutrientes, no entanto, essas fontes de lipídios afetam a digestibilidade do extrato etéreo. A adição de óleo mineral reduz os níveis plasmáticos de HDL-C, ao passo que a adição de gordura animal e gordura vegetal não altera as concentrações plasmáticas de colesterol.

Dietary calcium intake and overweight: an epidemiologic view

OBJECTIVE: We evaluated the relation between overweight and calcium intake in adults living in the municipality of São Paulo, Brazil. METHODS: This was a cross-sectional population-based study on a sample of 1459 adults that was obtained by multistage cluster sampling. Dietary intake was measured by the 24-h recall method. Poisson's and linear regression analyses were performed to evaluate the relation between overweight and quartiles of calcium intake adjusted for energy. RESULTS: The prevalence of overweight was 43.1% and the average adjusted calcium intake was 448.6 mg. In the linear regression analyses, the regression coefficient for adjusted calcium was significant and negative (P = 0.019, beta(1) = -0.0001). Although evaluated by quartiles, the prevalence ratio for overweight in the first quartile of calcium intake was 1.24 (95% confidence interval 1.00-1.54) and that in the second quartile was 1.24 (95% confidence interval 1.03-1.49). CONCLUSION: In the present study, calcium intake showed a significant negative association with body mass index

Tendência da incidência e da mortalidade por Aids em mulheres na transição menopausal e pós-menopausa no Brasil, 1996-2005

Objetivo: Descrever a incidência e a mortalidade por Aids no Brasil e mulheres na fase menopausal e pós-menopausa. Métodos: Estudo retrospectivo de 1996 a 2005, utilizando dados secundários do Sistema de Informações de Saúde do DATASUS - Ministério da Saúde. Buscou-se por população residente em dados "Demográficos e Socioeconômicos, incidência no Sistema de Informação de Agravos de Notificação (SINAN) e mortalidade no Sistema de Informação sobre Mortalidade (SIM). Os coeficientes específicos de incidência e de mortalidade por Aids/100.000 mulheres foram calculados para cada década da faixa etária de 30 a 69 anos (30-39, 40-49, 50-59, 60-69), pois inclui a população de interesse; isto é, mulheres na transição menopausal e pós-menopausa, dos 35 aos 65 anos, Resultados: Houve aumento da incidência de Aids entre os anos de 1996 e 1998, a partir daí, observa-se tendência à ligeira queda até 2000 e posterior incremento até 2004. Em 2005, o coeficiente retorna a valores próximos dos encontrados em 1997. A mortalidade apresentou queda em todas as faixas etárias nos anos de 1996 e 1997, a partir de então, os coeficientes mantêm-se praticamente estáveis até 1999, exceto na faixa etária de 30 a 39 anos que continua estável até 2005. Já entre mulheres acima de 40 anos, o coeficiente de mortalidade apresentou aumento entre os anos 1999 a 2005. conclusão: Houve aumento no número de casos novos de Aids entre mulheres acima de 30 anos e o mesmo processo se repetiu com relação à mortalidade. O aumento e "envelhecimento" da epidemia entre brasileiras, sinalizam que medidas de promoção à saúde, prevenção da doença, diagnóstico precoce e tratamento efetivo devem ser oferecidos de maneira apropriada às mulheres de 30 a 69 anos, considerando as características pessoais, o contexto familiar e o papel social do sexo feminino nestas idades

Tendência da mortalidade relacionada à paracoccidioidomicose, Estado de São Paulo, Brasil, 1985 a 2005: estudou usando causas múltiplas de morte

Objetivo. Estudar a mortalidade relacionada à paracoccidioidomicose informada em qualquer linha ou parte do atestado médico da declaração de óbito. Métodos. Os dados provieram dos bancos de causas múltiplas de morte da Fundação Sistema Estadual de Análise de Dados (SEADE) de São Paulo entre 1985 e 2005. Foram calculados os coeficientes padronizados de mortalidade relacionada à paracoccidioidomicose como causa básica, como causa associada e pelo total de suas menções. Resultados. No período de 21 anos ocorreram 1 950 óbitos, sendo a paracoccidioidomicose a causa básica de morte em 1 164 (59,7%) e uma causa associada de morte em 786 (40,3%). Entre 1985 e 2005 observou-se um declínio do coeficiente de mortalidade pela causa básica de 59,8% e pela causa associada, de 53,0%. O maior número de óbitos ocorreu entre os homens, nas idades mais avançadas, entre lavradores, com tendência de aumento nos meses de inverno. As principais causas associadas da paracoccidioidomicose como causa básica foram a fibrose pulmonar, as doenças crônicas das vias aéreas inferiores e as pneumonias. As neoplasias malignas e a AIDS foram as principais causas básicas estando a paracoccidioidomicose como causa associada. Verificou-se a necessidade de adequar as tabelas de decisão para o processamento automático de causas de morte nos atestados de óbito com a menção de paracoccidioidomicose. Conclusões. A metodologia das causas múltiplas de morte, conjugada com a metodologia tradicional da causa básica, abre novas perspectivas para a pesquisa que visa a ampliar o conhecimento sobre a história natural da paracoccidioidomicose.

Development of a Multicommutated Flow System with Chemiluminometric Detection for Quantification of Gentamicin in Pharmaceuticals

A new flow procedure based on multicommutation with chemiluminometric detection was developed to quantify gentamicin sulphate in pharmaceutical formulations. This approach is based on gentamicin's ability to inhibit the chemiluminometric reaction between luminol and hypochlorite in alkaline medium, causing a decrease in the analytical signal. The inhibition of the analytical signal is proportional to the concentration of gentamicin sulphate, within a linear range of 1 to 4 mu g mL(-1) with a coefficient variation <3%. A sample throughput of 55 samples h(-1) was obtained. The developed method is sensitive, simple, with low reagent consumption, reproducible, and inexpensive, and when applied to the analysis of pharmaceutical formulations (eye drops and injections) it gave results with RSD between 1.10 and 4.40%.

Development, implementation, and assessment of a distance module in endocrine physiology

Rangel EM, Mendes IA, Carnio EC, Marchi Alves LM, Godoy S, Crispim JA. Development, implementation, and assessment of a distance module in endocrine physiology. Adv Physiol Educ 34: 70-74, 2010; doi: 10.1152/advan.00070.2009.-This study aimed to develop, implement, and assess a distance module in endocrine physiology in TelEduc for undergraduate nursing students from a public university in Brazil, with a sample size of 44 students. Stage 1 consisted of the development of the module, through the process of creating a distance course by means of the Web. Stage 2 was the planning of the module's practical functioning, and stage 3 was the planning of student evaluations. In the experts' assessment, the module complied with pedagogical and technical requirements most of the time. In the practical functioning stage, 10 h were dedicated for on-site activities and 10 h for distance activities. Most students (93.2%) were women between 19 and 23 yr of age (75%). The internet was the most used means to remain updated for 23 students (59.0%), and 30 students (68.2%) accessed it from the teaching institution. A personal computer was used by 23 students (56.1%), and most of them (58.1%) learned to use it alone. Access to a forum was more dispersed (variation coefficient: 86.80%) than access to chat (variation coefficient: 65.14%). Average participation was 30 students in forums and 22 students in the chat. Students' final grades in the module averaged 8.5 (SD: 1.2). TelEduc was shown to be efficient in supporting the teaching- learning process of endocrine physiology.

Risk optimization of a steel frame communications tower subject to tornado winds

The structural engineering community in Brazil faces new challenges with the recent occurrence of high intensity tornados. Satellite surveillance data shows that the area covering the south-east of Brazil, Uruguay and some of Argentina is one of the world most tornado-prone areas, second only to the infamous tornado alley in central United States. The design of structures subject to tornado winds is a typical example of decision making in the presence of uncertainty. Structural design involves finding a good balance between the competing goals of safety and economy. This paper presents a methodology to find the optimum balance between these goals in the presence of uncertainty. In this paper, reliability-based risk optimization is used to find the optimal safety coefficient that minimizes the total expected cost of a steel frame communications tower, subject to extreme storm and tornado wind loads. The technique is not new, but it is applied to a practical problem of increasing interest to Brazilian structural engineers. The problem is formulated in the partial safety factor format used in current design codes, with all additional partial factor introduced to serve as optimization variable. The expected cost of failure (or risk) is defined as the product of a. limit state exceedance probability by a limit state exceedance cost. These costs include costs of repairing, rebuilding, and paying compensation for injury and loss of life. The total expected failure cost is the sum of individual expected costs over all failure modes. The steel frame communications, tower subject of this study has become very common in Brazil due to increasing mobile phone coverage. The study shows that optimum reliability is strongly dependent on the cost (or consequences) of failure. Since failure consequences depend oil actual tower location, it turn,,; out that different optimum designs should be used in different locations. Failure consequences are also different for the different parties involved in the design, construction and operation of the tower. Hence, it is important that risk is well understood by the parties involved, so that proper contracts call be made. The investigation shows that when non-structural terms dominate design costs (e.g, in residential or office buildings) it is not too costly to over-design; this observation is in agreement with the observed practice for non-optimized structural systems. In this situation, is much easier to loose money by under-design. When by under-design. When structural material cost is a significant part of design cost (e.g. concrete dam or bridge), one is likely to lose significantmoney by over-design. In this situation, a cost-risk-benefit optimization analysis is highly recommended. Finally, the study also shows that under time-varying loads like tornados, the optimum reliability is strongly dependent on the selected design life.

Chaotic Patterns in Aeroelastic Signals

This work presents the analysis of nonlinear aeroelastic time series from wing vibrations due to airflow separation during wind tunnel experiments. Surrogate data method is used to justify the application of nonlinear time series analysis to the aeroelastic system, after rejecting the chance for nonstationarity. The singular value decomposition (SVD) approach is used to reconstruct the state space, reducing noise from the aeroelastic time series. Direct analysis of reconstructed trajectories in the state space and the determination of Poincare sections have been employed to investigate complex dynamics and chaotic patterns. With the reconstructed state spaces, qualitative analyses may be done, and the attractors evolutions with parametric variation are presented. Overall results reveal complex system dynamics associated with highly separated flow effects together with nonlinear coupling between aeroelastic modes. Bifurcations to the nonlinear aeroelastic system are observed for two investigations, that is, considering oscillations-induced aeroelastic evolutions with varying freestream speed, and aeroelastic evolutions at constant freestream speed and varying oscillations. Finally, Lyapunov exponent calculation is proceeded in order to infer on chaotic behavior. Poincare mappings also suggest bifurcations and chaos, reinforced by the attainment of maximum positive Lyapunov exponents. Copyright (C) 2009 F. D. Marques and R. M. G. Vasconcellos.

Diffusive Synchronization of Hyperchaotic Lorenz Systems

The synchronizing properties of two diffusively coupled hyperchaotic Lorenz 4D systems are investigated by calculating the transverse Lyapunov exponents and by observing the phase space trajectories near the synchronization hyperplane. The effect of parameter mismatch is also observed. A simple electrical circuit described by the Lorenz 4D equations is proposed. Some results from laboratory experiments with two coupled circuits are presented. Copyright (C) 2009 Ruy Barboza.

Effects of Variations in Nonlinear Damping Coefficients on the Parametric Vibration of a Cantilever Beam with a Lumped Mass

Uncertainties in damping estimates can significantly affect the dynamic response of a given flexible structure. A common practice in linear structural dynamics is to consider a linear viscous damping model as the major energy dissipation mechanism. However, it is well known that different forms of energy dissipation can affect the structure's dynamic response. The major goal of this paper is to address the effects of the turbulent frictional damping force, also known as drag force on the dynamic behavior of a typical flexible structure composed of a slender cantilever beam carrying a lumped-mass on the tip. First, the system's analytical equation is obtained and solved by employing a perturbation technique. The solution process considers variations of the drag force coefficient and its effects on the system's response. Then, experimental results are presented to demonstrate the effects of the nonlinear quadratic damping due to the turbulent frictional force on the system's dynamic response. In particular, the effects of the quadratic damping on the frequency-response and amplitude-response curves are investigated. Numerically simulated as well as experimental results indicate that variations on the drag force coefficient significantly alter the dynamics of the structure under investigation. Copyright (c) 2008 D. G. Silva and P. S. Varoto.

Stability and ergodicity of piecewise deterministic Markov processes

The main goal of this paper is to establish some equivalence results on stability, recurrence, and ergodicity between a piecewise deterministic Markov process ( PDMP) {X( t)} and an embedded discrete-time Markov chain {Theta(n)} generated by a Markov kernel G that can be explicitly characterized in terms of the three local characteristics of the PDMP, leading to tractable criterion results. First we establish some important results characterizing {Theta(n)} as a sampling of the PDMP {X( t)} and deriving a connection between the probability of the first return time to a set for the discrete-time Markov chains generated by G and the resolvent kernel R of the PDMP. From these results we obtain equivalence results regarding irreducibility, existence of sigma-finite invariant measures, and ( positive) recurrence and ( positive) Harris recurrence between {X( t)} and {Theta(n)}, generalizing the results of [ F. Dufour and O. L. V. Costa, SIAM J. Control Optim., 37 ( 1999), pp. 1483-1502] in several directions. Sufficient conditions in terms of a modified Foster-Lyapunov criterion are also presented to ensure positive Harris recurrence and ergodicity of the PDMP. We illustrate the use of these conditions by showing the ergodicity of a capacity expansion model.

Near-infrared third-order nonlinearity of PbO-GeO(2) films containing Cu and Cu(2)O nanoparticles

We report measurements of the nonlinear (NL) refractive index n(2) of lead-germanium films (LGFs) containing Cu and Cu(2)O nanoparticles (NPs). The thermally managed eclipse Z-scan technique with 150 fs pulses from a laser operating at 800 nm was used. The NL refractive index measured, n(2)=6.3x10(-12) cm(2)/W has electronic origin and the NL absorption coefficient alpha(2) is smaller than 660 cm/GW. The figure of merit n(2)/lambda alpha(2) is enhanced by more than two orders of magnitude in comparison with the result for the LGFs without the copper based NPs. (C) 2008 American Institute of Physics.

Sliding wear of weld layers with application to cane mill shaft rebuilding

Three welding procedures used to rebuild worn shafts in sugar cane mills were analysed: two submerged arc welding processes and one flux cored arc welding (FCAW) process. Sliding wear tests were in accordance with ASTM G 77 standard, using rings of welding material, blocks of bronze SAE 67, and oil as lubricant. The worn surfaces of rings and blocks were analysed by scanning electron microscopy to determine the wear mechanisms. High contact pressure, high operating temperature, and low relative speed were applied in sliding wear tests to match the conditions in sugar cane mills. Transferred material and evidence of adhesive junctions were detected. Additionally, hardened fragments produced abrasive grooves on the worn surfaces. The welding deposits that presented strong adhesion on the worn surface showed higher mass loss than the materials that presented more abrasive characteristics. Plastic mechanical properties were measured and related to the mass loss. The tested materials presented similar hardness but different yield stress and hardening coefficient. A relationship between wear, strain hardening coefficient, and yield stress was found. The welding deposit that presented the highest hardening coefficient showed the highest mass loss, with evidence of severe adhesion on the worn surface.

NEAR INFRARED SPECTROSCOPY FOR ESTIMATING SUGARCANE BAGASSE CONTENT IN MEDIUM DENSITY FIBERBOARD

Medium density fiberboard (MDF) is an engineered wood product formed by breaking down selected lignin-cellulosic material residuals into fibers, combining it with wax and a resin binder, and then forming panels by applying high temperature and pressure. Because the raw material in the industrial process is ever-changing, the panel industry requires methods for monitoring the composition of their products. The aim of this study was to estimate the ratio of sugarcane (SC) bagasse to Eucalyptus wood in MDF panels using near infrared (NIR) spectroscopy. Principal component analysis (PCA) and partial least square (PLS) regressions were performed. MDF panels having different bagasse contents were easily distinguished from each other by the PCA of their NIR spectra with clearly different patterns of response. The PLS-R models for SC content of these MDF samples presented a strong coefficient of determination (0.96) between the NIR-predicted and Lab-determined values and a low standard error of prediction (similar to 1.5%) in the cross-validations. A key role of resins (adhesives), cellulose, and lignin for such PLS-R calibrations was shown. PLS-DA model correctly classified ninety-four percent of MDF samples by cross-validations and ninety-eight percent of the panels by independent test set. These NIR-based models can be useful to quickly estimate sugarcane bagasse vs. Eucalyptus wood content ratio in unknown MDF samples and to verify the quality of these engineered wood products in an online process.