Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Gibberellic acid signaling is required for ambient temperature-mediated induction of flowering in Arabidopsis thaliana.

Distinct molecular mechanisms integrate changes in ambient temperature into the genetic pathways that govern flowering time in Arabidopsis thaliana. Temperature-dependent eviction of the histone variant H2A.Z from nucleosomes has been suggested to facilitate the expression of FT by PIF4 at elevated ambient temperatures. Here we show that, in addition to PIF4, PIF3 and PIF5, but not PIF1 and PIF6, can promote flowering when expressed specifically in phloem companion cells (PCC), where they can induce FT and its close paralog, TSF. However, despite their strong potential to promote flowering, genetic analyses suggest that the PIF genes seem to have only a minor role in adjusting flowering in response to photoperiod or high ambient temperature. In addition, loss of PIF function only partially suppressed the early flowering phenotype and FT expression of the arp6 mutant, which is defective in H2A.Z deposition. In contrast, the chemical inhibition of gibberellic acid (GA) biosynthesis resulted in a strong attenuation of early flowering and FT expression in arp6. Furthermore, GA was able to induce flowering at low temperature (15°C) independently of FT, TSF, and the PIF genes, probably directly at the shoot apical meristem. Together, our results suggest that the timing of the floral transition in response to ambient temperature is more complex than previously thought and that GA signaling might play a crucial role in this process.

Polttomoottorivoimalan energiatehokkuuden parantaminen hukkalämpövirtojen sähköksi muunnolla

Tämä diplomityö on osa FCEP hankeen Lappeenrannan teknillisessä yliopistossa tehtävää tutkimusta polttomoottoreiden energiatehokkuuden parantamisesta. Työn tavoitteena on saada tutkimustietoa polttomoottoreiden hukkalämpövirtojen hyödyntämisestä sähköntuotannossa. Tavoitteena on kartoittaa polttomoottorin hukkalämpövirtojen sähköksi muunnon potentiaalia valituilla menetelmillä ja tekniikoilla. Työssä tarkasteltavaksi moottoriksi valittiin DF- monipolttoainemoottori. DF-moottorin polttoaineena voidaan käyttää joko kaasua tai polttoöljyä. Laskennat suoritettiin moottorin valmistajan antamien hukkalämpövirtojen arvojen ja moottorin lämpötaseen avulla. Laskennan perusperiaatteena oli vesihöyryprosessin ja ORC-prosessien vertailu pakokaasulämmön hyödyntämisessä sekä matalalämpöisten hukkalämpövirtojen hyödyntäminen ORC-prosesseilla. Lisäksi työssä tutkittiin korkealla painesuhteella ja korkealla hyötysuhteella toimivan turboahtimen vaikutusta hukkalämpövirroista saatavaan tehoon. Diplomityössä tarkasteltiin moottorin lämpötaseen mukaisten arvojen lisäksi moottorin parametrien muuttamisen vaikutusta hukkalämpövirroista saatavaan tehoon. Moottorin parametrien muuttamisen vaikutusta moottorin akselitehoon tai moottorin lämpötaseeseen ei kuitenkaan tämän tutkimuksen puitteissa tarkasteltu. Työssä saatiin arvokasta tietoa polttomoottoreiden hukkalämpövirtojen muuntamisesta sähköksi eri menetelmillä sekä moottorin energiatehokkuuden parantamisesta.

Advanced welding technologies used for arctic metal structures

Rapid depletion of easy-to-access fossil fuel, predominantly, oil and gas resources has now necessitated increase in need to develop new oil and gas sources in ever more remote and hostile environments. This is necessary in order to explore more oil and gas resources to meet rapidly rising long-term energy demand in the world, both at present and in the nearest future. Arctic is one of these harsh environments, where enormous oil and gas resources are available, containing about 20% of the world total oil and gas, but the environmental conditions are very harsh and hostile. However, virtually all the facilities required for the exploration and development of this new energy source are constructed with metals as well as their alloys and are predominantly joined together by welding processes and technologies. Meanwhile, due to entirely different environment from the usual moderate temperate region, conventional welding technologies, common metals and their alloys cannot be applied as this Arctic environment demand metals structures with very high toughness and strength properties under extremely low temperature. This is due to the fact that metals transit from ductility to brittleness as the temperature moves toward extreme negative values. Hence, this research work investigates and presents the advanced welding technologies applicable to Arctic metal structures which can give satisfactory weldments under active Arctic service conditions. .

Characterisation of Laser Beam and Paper Material Interaction

It is known already from 1970´s that laser beam is suitable for processing paper materials. In this thesis, term paper materials mean all wood-fibre based materials, like dried pulp, copy paper, newspaper, cardboard, corrugated board, tissue paper etc. Accordingly, laser processing in this thesis means all laser treatments resulting material removal, like cutting, partial cutting, marking, creasing, perforation etc. that can be used to process paper materials. Laser technology provides many advantages for processing of paper materials: non-contact method, freedom of processing geometry, reliable technology for non-stop production etc. Especially packaging industry is very promising area for laser processing applications. However, there are only few industrial laser processing applications worldwide even in beginning of 2010´s. One reason for small-scale use of lasers in paper material manufacturing is that there is a shortage of published research and scientific articles. Another problem, restraining the use of laser for processing of paper materials, is colouration of paper material i.e. the yellowish and/or greyish colour of cut edge appearing during cutting or after cutting. These are the main reasons for selecting the topic of this thesis to concern characterization of interaction of laser beam and paper materials. This study was carried out in Laboratory of Laser Processing at Lappeenranta University of Technology (Finland). Laser equipment used in this study was TRUMPF TLF 2700 carbon dioxide laser that produces a beam with wavelength of 10.6 μm with power range of 190-2500 W (laser power on work piece). Study of laser beam and paper material interaction was carried out by treating dried kraft pulp (grammage of 67 g m-2) with different laser power levels, focal plane postion settings and interaction times. Interaction between laser beam and dried kraft pulp was detected with different monitoring devices, i.e. spectrometer, pyrometer and active illumination imaging system. This way it was possible to create an input and output parameter diagram and to study the effects of input and output parameters in this thesis. When interaction phenomena are understood also process development can be carried out and even new innovations developed. Fulfilling the lack of information on interaction phenomena can assist in the way of lasers for wider use of technology in paper making and converting industry. It was concluded in this thesis that interaction of laser beam and paper material has two mechanisms that are dependent on focal plane position range. Assumed interaction mechanism B appears in range of average focal plane position of 3.4 mm and 2.4 mm and assumed interaction mechanism A in range of average focal plane position of 0.4 mm and -0.6 mm both in used experimental set up. Focal plane position 1.4 mm represents midzone of these two mechanisms. Holes during laser beam and paper material interaction are formed gradually: first small hole is formed to interaction area in the centre of laser beam cross-section and after that, as function of interaction time, hole expands, until interaction between laser beam and dried kraft pulp is ended. By the image analysis it can be seen that in beginning of laser beam and dried kraft pulp material interaction small holes off very good quality are formed. It is obvious that black colour and heat affected zone appear as function of interaction time. This reveals that there still are different interaction phases within interaction mechanisms A and B. These interaction phases appear as function of time and also as function of peak intensity of laser beam. Limit peak intensity is the value that divides interaction mechanism A and B from one-phase interaction into dual-phase interaction. So all peak intensity values under limit peak intensity belong to MAOM (interaction mechanism A one-phase mode) or to MBOM (interaction mechanism B onephase mode) and values over that belong to MADM (interaction mechanism A dual-phase mode) or to MBDM (interaction mechanism B dual-phase mode). Decomposition process of cellulose is evolution of hydrocarbons when temperature is between 380- 500°C. This means that long cellulose molecule is split into smaller volatile hydrocarbons in this temperature range. As temperature increases, decomposition process of cellulose molecule changes. In range of 700-900°C, cellulose molecule is mainly decomposed into H2 gas; this is why this range is called evolution of hydrogen. Interaction in this range starts (as in range of MAOM and MBOM), when a small good quality hole is formed. This is due to “direct evaporation” of pulp via decomposition process of evolution of hydrogen. And this can be seen can be seen in spectrometer as high intensity peak of yellow light (in range of 588-589 nm) which refers to temperature of ~1750ºC. Pyrometer does not detect this high intensity peak since it is not able to detect physical phase change from solid kraft pulp to gaseous compounds. As interaction time between laser beam and dried kraft pulp continues, hypothesis is that three auto ignition processes occurs. Auto ignition of substance is the lowest temperature in which it will spontaneously ignite in a normal atmosphere without an external source of ignition, such as a flame or spark. Three auto ignition processes appears in range of MADM and MBDM, namely: 1. temperature of auto ignition of hydrogen atom (H2) is 500ºC, 2. temperature of auto ignition of carbon monoxide molecule (CO) is 609ºC and 3. temperature of auto ignition of carbon atom (C) is 700ºC. These three auto ignition processes leads to formation of plasma plume which has strong emission of radiation in range of visible light. Formation of this plasma plume can be seen as increase of intensity in wavelength range of ~475-652 nm. Pyrometer shows maximum temperature just after this ignition. This plasma plume is assumed to scatter laser beam so that it interacts with larger area of dried kraft pulp than what is actual area of beam cross-section. This assumed scattering reduces also peak intensity. So result shows that assumably scattered light with low peak intensity is interacting with large area of hole edges and due to low peak intensity this interaction happens in low temperature. So interaction between laser beam and dried kraft pulp turns from evolution of hydrogen to evolution of hydrocarbons. This leads to black colour of hole edges.

Työkoneiden dieselmoottoreiden hyötysuhteen parantaminen lämmöntalteenoton avulla

Tämä diplomityö on osa Lappeenrannan teknillisessä yliopistossa tehtävää tutkimusta polttomoottoreiden energiatehokkuuden parantamisessa. Työn tavoitteena on saada tutkimustietoa polttomoottoreiden hukkalämpövirtojen hyödyntämisestä sähköntuotannossa. Tavoitteena on muodostaa näkemys Mikro-ORC energiamuuntimen mahdollisuuksista ja reunaehdoista osana työkoneluokan (150 kW… 400 kW) dieselmoottorikokonaisuutta, erityisesti maataloussektorilla. Työssä tarkasteltaviksi moottoreiksi valittiin kaksi eri AGCO Sisu Powerin dieselmoottoria. Laskennat suoritettiin moottorin valmistajan antamien hukkalämpövirtojen arvojen perusteella. Laskennan perusperiaatteena oli tutkia ORC-prosessin tuottamaa lisäsähkötehoa hyödyntämällä pakokaasujen lämpöenergiaa korkea-, keski- ja matalalämpötiloissa. Työssä vertailtiin kahden eri kiertoaineen prosessihyötysuhdetta, saatava sähkötehoa sekä prosessin sisäisiä parametreja. Lisäksi työssä tutkittiin ORC-prosessin laskentaa suunnittelupisteessä (design) ja suunnittelupisteen ulkopuolella (off-design), prosessisuureiden optimointia ja lämmönsiirtimien mitoitusta. Diplomityössä tarkasteltiin moottorin energiataseen mukaisten arvojen lisäksi moottorin parametrien muuttamisen vaikutusta hukkalämpövirroista saatavan tehoon. Työssä saatiin arvokasta tietoa polttomoottoreiden hukkalämpövirtojen muuntamisesta sähköksi ORC:lla sekä moottorin energiatehokkuuden parantamisesta.

Defining of the material models for stainless steels to be used in FE modeling

The aim of this work is to study the results of tensile tests for austenitic stainless steel type 304 and make accurate FE-models according to the results of the tests. Tensile tests were made at Central Research Institute of Structural Material, Prometey at Saint Petersburg and Mariyenburg in Russia. The test specimens for the tensile tests were produced at Lappeenranta University of Technology in a Laboratory of Steel Structures. In total 4 different tests were made, two with base material specimens and two with transverse butt weld specimens. Each kind of a specimen was tested at room temperature and at low temperature. By comparing the results of room and low temperature tests of similar test specimen we get to study the results of work hardening that affect the austenitic steels at below room temperature. The produced specimens are to be modeled accurately and then imported for nonlinear FEM- analyzing. Using the data gained from the tensile tests the aim is to get the models work like the specimens did during the tests. By using the analyzed results of the FE-models the aim is to calculate and get the stress-strain curves that correspond to the results acquired from the tensile tests.

Pressure-assisted cold denaturation of hen egg white lysozyme: the influence of co-solvents probed by hydrogen exchange nuclear magnetic resonance

COSY proton nuclear magnetic resonance was used to measure the exchange rates of amide protons of hen egg white lysozyme (HEWL) in the pressure-assisted cold-denatured state and in the heat-denatured state. After dissolving lysozyme in deuterium oxide buffer, labile protons exchange for deuterons in such a way that exposed protons are substituted rapidly, whereas "protected" protons within structured parts of the protein are substituted slowly. The exchange rates k obs were determined for HEWL under heat treatment (80ºC) and under high pressure conditions at low temperature (3.75 kbar, -13ºC). Moreover, the influence of co-solvents (sorbitol, urea) on the exchange rate was examined under pressure-assisted cold denaturation conditions, and the corresponding protection factors, P, were determined. The exchange kinetics upon heat treatment was found to be a two-step process with initial slow exchange followed by a fast one, showing residual protection in the slow-exchange state and P-factors in the random-coil-like range for the final temperature-denatured state. Addition of sorbitol (500 mM) led to an increase of P-factors for the pressure-assisted cold denatured state, but not for the heat-denatured state. The presence of 2 M urea resulted in a drastic decrease of the P-factors of the pressure-assisted cold denatured state. For both types of co-solvents, the effect they exert appears to be cooperative, i.e., no particular regions within the protein can be identified with significantly diverse changes of P-factors.

Eletrical conductivity and deterioration of soybean seeds exposed to different storage conditions

Research with soybean seeds has revealed that the results of the electrical conductivity test may be influenced by storage temperature, particularly low temperature, such as 10ºC, suggesting that seed deterioration at low storage temperatures does not seem to be directly related to the loss of the cell membrane integrity. This study was conducted with seeds of two soybean cultivars with the objective of: a) studying the effect of different storage temperatures (10ºC; 20ºC; 25ºC; 20/10ºC and 25/10ºC) on the results of the electrical conductivity test; b) observing the behavior of fatty acids and carbohydrates during storage and studying its relation with the electrical conductivity results. Every three months, from a total of 18 months of storage, the physiological quality of seeds was evaluated using the germination, accelerated aging and electrical conductivity tests. Based on the obtained results, it can be concluded that the electrical conductivity test was not shown to be a good indicative of the deterioration process of seeds stored at low temperatures, and no direct relationship between changes in the fatty acids and carbohydrates and the behavior of the mentioned test for seeds stored at 10ºC was found.

Crystal Growth and Characterization of Li0.9Mo6O17

Purple bronze Li0.9Mo6O17 has attracted researchers for its low dimensionality and corresponding properties. Although it has been studied for nearly two decades, there are still some unsolved puzzles with this unique material. Single crystals of Li0.9Mo6O17 were grown using the temperature gradient flux technique in this research. The crystal growth was optimized by experimenting different conditions and good quality crystals were obtained. X-ray diffraction results have confirmed the right phase of the crystals. Resistivity measurements and magnetic susceptibility measurements were carried out, and anomalous electronic behaviors were found. All of the samples showed the metal-insulator transition near 20K, followed by behavior that differs from sample to sample: either superconducting, metallic or insulating behavior was observed below 2K. Li0.9Mo6O17 was considered as a quasi-one-dimensional crystal and also a superconducting crystal, which implies a dimensional crossover may occur at the metal-insulator transition. A two-band scenario of the Luttinger liquid model was used to fit the resistivity data and excellent results were achieved, suggesting that the Luttinger theory is a very good candidate for the explanation of the anomalous behavior of Li0.9Mo6O17. In addition, the susceptibility measurements showed Curie paramagnetism and some temperature independent paramagnetism at low temperature. The absence of any anomalous magnetic feature near 20K where the resistivity upturn takes place, suggests that a charge density wave mechanism, which has been proposed by some researchers, is not responsible for the unique properties of Li0.9Mo6O17.

Synthèse stéréosélective de motifs polypropionates via la chimie des radicaux : application à l'élaboration de l'hémisphère ouest de la narasine

Cet ouvrage traite principalement de la synthèse de motifs polypropionates de type stéréopentade ainsi qu’une application à la synthèse d’une molécule naturelle possèdant des propriétés biologiques. La stratégie envisagée pour l’élaboration de ces motifs récurrents dans plusieurs structures d’origine naturelle fait appel à la chimie des radicaux. Cette thèse se divise en différents chapitres dans lesquels la versatilité de la méthodologie développée sera démontrée. En premier lieu, il sera question de présenter l’importance de la synthèse de motifs polypropionates. Le domaine couvert par la chimie de ces molécules complexes hautement fonctionnalisées a contribué énormément à l’avancement de nos connaissances en synthèse organique, particulièrement dans le contexte des réactions impliquant des molécules acyliques. Une brève description des méthodes connues est présentée afin de saisir l’étendue des défis restants pour construire efficacement tous les isomères possibles des polypropionates de type stéréopentade. La stratégie proposée est basée sur une approche contrôlée entièrement par le substrat. Ce contrôle s’appuie sur le choix judicieux de l’acide de Lewis activant les deux réactions impliquées, soit la réaction de Mukaiyama et le transfert d’hydrogène. La seconde section de cette thèse concerne principalement le développement d’une réaction de Mukaiyama impliquant un éther d’énol silylé portant un lien pouvant être homolytiquement brisé dans la réaction suivante et un aldéhyde de type propionate. Le contrôle de l’aldolisation provient de la nature de l’acide de Lewis. Une espèce monodentate (BF3·OEt2) génère une relation 3,4-syn selon le modèle dit Felkin-Anh tandis que les acides de Lewis bidentates mènent à la relation 3,4-anti via un état de transition définit comme Cram-chélate. Une optimisation des conditions réactionnelles en variant l’acidité et la stoechiométrie de l’acide de Lewis de titane a permis de construire diastéréosélectivement le produit de Mukaiyama ayant une relation 3,4-anti. En outre, la nature des complexes impliqués dans ces réactions a été élucidée par des études RMN 13C à basse température. Une fois les précurseurs radicalaires synthétisés, notre méthodologie de réduction par transfert d’hydrogène contrôlée également par les acides de Lewis s’avère très efficace. Les acides de Lewis dérivés d’aluminium mènent sélectivement à la relation 2,3-syn selon un contrôle endocyclique tandis que les acides de Lewis de bore permettent la création des relations 2,3-anti en se basant sur une stabilisation par les divers facteurs de contrôle de molécules acycliques. Cette stratégie novatrice nous a ainsi permis de construire efficacement les 16 diastéréoisomères possibles. Le chapitre suivant concerne l’application de cette méthodologie à la synthèse de l’hémisphère ouest de la salinomycine et de la narasine. Plusieurs défis synthétiques ont été relevés à cette occasion par la présence de nombreux centres stéréogènes contigus. Nous avons réalisé que la relation stéréochimique 2,3-anti de la salinomycine n’est pas accessible sélectivement par la chimie des radicaux via l’effet exocyclique. Des études ont été entreprises afin de comprendre cette perte de sélectivité. Les conclusions suggèrent que les substituants sur le cycle imposent un biais conformationnel conduisant à des faibles sélectivités. Une alternative utilisant un réactif de crotylsilane chiral a été développée pour arriver à la molécule cible. Cette situation est différente dans le cas de la narasine où la présence du méthyle sur le carbone en position β du radical bloque efficacement l’approche d’une des faces d’attaque par l’hydrure. Des sélectivités impressionnantes nous ont permis de construire le fragment C1-C9 de la narasine de manière expéditive et efficace. Finalement, l’élongation sélective utilisant à nouveau la séquence d’aldolisation de Mukaiyama/réduction radicalaire suivie d’un couplage de type aldol stéréosélectif conduit au fragment C1-C17 de la narasine (hémisphère ouest)en 19 étapes avec un rendement global de l’ordre de 7 %. En dernier lieu, nous nous sommes penchés sur la réactivité des α-bromo-β- alkoxycétones lors de transfert d’hydrogène. Nous avons découvert que la chimie de ces derniers pourrait s’avérer utile dans le contexte de la synthèse de motifs complexes polypropionates. La présence d’un centre stéréogène de l’autre coté de la cétone semble avoir un impact sur la sélectivité.

Étude de l'influence de la réassociation en surface des atomes N et O sur l'inactivation des spores bactériennes dans une post-décharge N2-O2 basse pression en flux

Le recours au plasma pour stériliser des dispositifs médicaux (DM) est un domaine de recherche ne datant véritablement que de la fin des années 1990. Les plasmas permettent, dans les conditions adéquates, de réaliser la stérilisation à basse température (≤ 65°C), tel qu’exigé par la présence de polymères dans les DM et ce contrairement aux procédés par chaleur, et aussi de façon non toxique, contrairement aux procédés chimiques comme, par exemple, l’oxyde d’éthylène (OEt). Les laboratoires du Groupe de physique des plasmas à l’Université de Montréal travaillent à l’élaboration d’un stérilisateur consistant plus particulièrement à employer les effluents d’une décharge N2-%O2 basse pression (2-8 Torrs) en flux, formant ce que l’on appelle une post-décharge en flux. Ce sont les atomes N et O de cette décharge qui viendront, dans les conditions appropriées, entrer en collisions dans la chambre de stérilisation pour y créer des molécules excitées NO*, engendrant ainsi l’émission d’une quantité appréciable de photons UV. Ceux-ci constituent, dans le cas présent, l’agent biocide qui va s’attaquer directement au bagage génétique du micro-organisme (bactéries, virus) que l’on souhaite inactiver. L’utilisation d’une lointaine post-décharge évite du même coup la présence des agents érosifs de la décharge, comme les ions et les métastables. L’un des problèmes de cette méthode de stérilisation est la réduction du nombre de molécules NO* créées par suite de la perte des atomes N et O, qui sont des radicaux connus pour interagir avec les surfaces, sur les parois des matériaux des DM que l’on souhaite stériliser. L’objectif principal de notre travail est de déterminer l’influence d’une telle perte en surface, dite aussi réassociation en surface, par l’introduction de matériaux comme le Téflon, l’acier inoxydable, l’aluminium et le cuivre sur le taux d’inactivation des spores bactériennes. Nous nous attendons à ce que la réassociation en surface de ces atomes occasionne ainsi une diminution de l’intensité UV et subséquemment, une réduction du taux d’inactivation. Par spectroscopie optique d’émission (SOE), nous avons déterminé les concentrations perdues de N et de O par la présence des matériaux dans le stérilisateur, ainsi que la diminution de l’émission UV en découlant. Nous avons observé que cette diminution des concentrations atomiques est d’autant plus importante que les surfaces sont catalytiques. Au cours de l’étude du phénomène de pertes sur les parois pour un mélange N2-%O2 nous avons constaté l’existence d’une compétition en surface entre les atomes N et O, dans laquelle les atomes d’oxygènes semblent dominer largement. Cela implique qu’au-delà d’un certain %O2 ajouté à la décharge N2, seuls les atomes O se réassocient en surface. Par ailleurs, l’analyse des courbes de survie bi-phasiques des micro-organismes a permis d’établir une étroite corrélation, par lien de cause à effet, entre la consommation des atomes N et O en surface et la diminution du taux d’inactivation des spores dans la première phase. En revanche, nous avons constaté que notre principal agent biocide (le rayonnement ultraviolet) est moins efficace dans la deuxième phase et, par conséquent, il n’a pas été possible d’établir un lien entre la diminution des concentrations et le taux d’inactivation de cette phase-là.

Low cost synthesis of cathode and anode materials for lithium-ion batteries

Dans cette thèse, nous démontrons des travaux sur la synthèse à faible coût des matériaux de cathode et l'anode pour les piles lithium-ion. Pour les cathodes, nous avons utilisé des précurseurs à faible coût pour préparer LiFePO4 et LiFe0.3Mn0.7PO4 en utilisant une méthode hydrothermale. Tout d'abord, des matériaux composites (LiFePO4/C) ont été synthétisés à partir d'un précurseur de Fe2O3 par une procédé hydrothermique pour faire LiFePO4(OH) dans une première étape suivie d'une calcination rapide pour le revêtement de carbone. Deuxièmement, LiFePO4 avec une bonne cristallinité et une grande pureté a été synthétisé en une seule étape, avec Fe2O3 par voie hydrothermale. Troisièmement, LiFe0.3Mn0.7PO4 a été préparé en utilisant Fe2O3 et MnO comme des précurseurs de bas coûts au sein d'une méthode hydrothermale synthétique. Pour les matériaux d'anode, nous avons nos efforts concentré sur un matériau d'anode à faible coût α-Fe2O3 avec deux types de synthèse hydrothermales, une a base de micro-ondes (MAH) l’autre plus conventionnelles (CH). La nouveauté de cette thèse est que pour la première fois le LiFePO4 a été préparé par une méthode hydrothermale en utilisant un précurseur Fe3+ (Fe2O3). Le Fe2O3 est un précurseur à faible coût et en combinant ses coûts avec les conditions de synthèse à basse température nous avons réalisé une réduction considérable des coûts de production pour le LiFePO4, menant ainsi à une meilleure commercialisation du LiFePO4 comme matériaux de cathode dans les piles lithium-ion. Par cette méthode de préparation, le LiFePO4/C procure une capacité de décharge et une stabilité de cycle accrue par rapport une synthétisation par la méthode à l'état solide pour les mêmes précurseurs Les résultats sont résumés dans deux articles qui ont été récemment soumis dans des revues scientifiques.

Development of Cell Culture Systems from Selected Species of Fish and Prawns

The present work deals with the development of primary cell culture and diploid cell lines from two fishes, such as Poecilia reticulata and Clarias gariepinus. The greatest difficulty experienced was the avoidance of bacterial and fungi contamination. Three types of cell cultures are commonly developed, primary cell culture, diploid cell lines and heteroploid cell lines. Primary cell culture obtained from the animal tissues that have been cultivated in vitro for the first time. They are characterized by the same chromosome number as parent tissue, cultivated in vitro for the first time, have wide range of virus susceptibility, usually not malignant, six chromatin retarded and do not grow as suspension cultures. Diploid cell lines arise from a primary cell culture at the time of subculturing. Diploid cell lines commercially used in virology are W1-38 (human embryonic lung), W1-26 (human embryonic lung) and HEX (Human embryonic kidney). Heteroploid cell lines have been subcultivated with less than 75% of the cells in the population having a diploid chromosome constitution. Tissue cultures have been extensively used in biomedical research. The main applications are in three areas, Karyological studies, Identification and study of hereditary metabolic disorders and Somatic cell genetics. Other applications are in virology and host-parasite relationships. In this study an attempt was made to preserve the ovarian tissue at low temperature in the presence of cryoprotectants so that the tissue can be retrieved at any time and a cell culture could be developed.

Effect of curing temperature , fibre loading and bonding agent on the equilibrium swelling of isora-natural rubbercomposites

Isora fibre-reinforced natural rubber (NR) composites were cured at 80, 100, 120 and 150°C using a low temperature curing accelerator system. Composites were also prepared using a conventional accelerator system and cured at 150°C. The swelling behavior of these composites at varying fibre loadings was studied in toluene and hexane. Results show that the uptake of solvent and volume fraction of rubber due to swelling was lower for the low temperature cured vulcanizates which is an indication of the better fibre/rubber adhesion. The uptake of aromatic solvent was higher than that of aliphatic solvent, for all the composites. As the fibre content increased, the solvent uptake decreased, due to the superior solvent resistance of the fibre and good fibre-rubber interactions. The bonding agent improved the swelling resistance of the composites due to the strong interfacial adhesion. Due to the improved adhesion between the fibre and rubber, the ratio of the change in volume fraction of rubber due to swelling to the volume fraction of rubber in the dry sample (V,) was found to decrease in the presence of bonding agent. At a fixed fibre loading, the alkali treated fibre composite showed a lower percentage swelling than untreated one for both systems showing superior rubber-fibre interactions.