Stable anode performance of an Sb–carbon nanocomposite in lithium-ion batteries and the effect of ball milling mode in the course of its preparation

Materials that alloy with lithium (Si, Ge, Sn, Sb, and P) are considered as alternatives to graphitic anodes in lithium-ion batteries. Their practical use is precluded by large volume changes (200–370%) during cycling. Embedding nanoparticles into carbon is being investigated as a way to tackle that, and ball milling is emerging as a technique to prepare nanocomposites with enhanced capacity and cyclic stability. Using Sb as a model system, we investigate the preparation of Sb–carbon nanocomposites using a reconfigurable ball mill. Four distinctive milling modes are compared. The structure of the composites varies depending on the mode. Frequent strong ball impacts are required for the optimal electrochemical performance of the nanocomposite. An outstanding stable capacity of 550 mA h g−1 for 250 cycles at a current rate of 230 mA g−1 is demonstrated in a thin electrode (1 mg cm−2) and a capacity of [similar]400 mA h g−1 can be retained at 1.15 A g−1. Some capacity fade is observed in a thicker electrode (2.5 mg cm−2), i.e. the performance is sensitive to mass loading. The electrochemical stability originates from the nanocomposite structure containing Sb nanoparticles (5–15 nm) dispersed in a carbon component.

Associations between young children's perceived and actual ball skill competence and physical activity

Objectives: The relationship between actual and perceived object control competence (ball skills) and the contribution to young children’s physical activity is not known.
Design: Cross sectional study.
Methods: The Test Gross Motor Development-2 assessed actual object control competence and a modified version of the Pictorial Scale of Perceived Competence and Social Acceptance for Young Children assessed perceived object control competence. Moderate- to vigorous-intensity physical activity was measured via accelerometry. Three mixed regression models were performed: (i) object control competence as the predictor and the outcome as perceived object control, (ii) perceived object control competence as the predictor and the outcome moderate to vigorous physical activity and (iii) actual object control as the predictor and the outcome moderate to vigorous physical activity. Models adjusted for school clustering, monitor wear time, sex and age. Interactions between respective predictor variables and sex were performed if warranted. A total of 102 children (56% boys, 44% girls) aged 4–8 years (M 6.3, SD 0.92) completed assessments.
Results: Girls had lower perceived and actual object control competence and were less active than boys. Actual object control competence was positively associated with perceived object control competence (B = 0.11, t(96) = 2.25, p < 0.001, p = 0.027) and this relationship did not differ by sex (p = 0.449); however, neither actual (p = 0.092) nor perceived object control competence (p = 0.827) were associated with moderate to vigorous physical activity.
Discussion: Young children’s perceived ball skill abilities appear to relate to actual competence; however, these measures were not associated with physical activity. In older children, object control skill is associated with physical activity so targeting young children’s object control skills is an intervention priority.

Electrochemical performance of LiFe1-xMnxPO4/C materials prepared by ball milling

LiFe1-xMnxPO4/C composite materials as cathode materials in Li-ion batteries have been synthesised and their electrochemical properties have been investigated. The samples were synthesised by using high energy ball milling of commercially available precursors (Li2C2O4, FeC2O4.2H2O, MnC2O4.2H2O, NH4H2PO4) and then heated at 600&deg;C. The morphology and structure of the heated samples were analysed by means of SEM and X-ray diffraction. The olivine structure of the LiFe1-xMnxPO4/C composite was obtained. A slight shift of the peaks to smaller 2θ angles with the increasing Mn/Fe ratios is observed due to the increase in lattice parameters. The influence of different Mn/Fe ratios on electrical and electrochemical performances were studied by charge-discharge and cyclic voltammetry (CV) testing. The CV curves of the pure LiFePO4 and LiMnPO4 show the expected Fe2+/Fe3+ peak around 3·5 V and Mn2+/Mn3+ peak around 4·1 V, respectively. The addition of manganese increases the discharge voltage from 3·5 to 4·1 V.

Enhanced lithium storage in ZnFe2O4-C nanocomposite produced by a low-energy ball milling

Preparation of novel nanocomposite structure of ZnFe2O4-C is achieved by combining a sol-gel and a low energy ball milling method. The crucial feature of the composite's structure is that sol-gel synthesised ZnFe2O4 nanoparticles are dispersed and attached uniformly along the chains of Super P Li&trade; carbon black matrix by adopting a low energy ball milling. The composite ZnFe2O4-C electrodes are capable of delivering a very stable reversible capacity of 681 mAh g-1 (96% retention of the calculated theoretical capacity of ∼710 mAh g-1) at 0.1 C after 100 cycles with a remarkable Coulombic efficiency (82%) improvement in the first cycle. The rate capability of the composite is significantly improved and obtained capacity was as high as 702 at 0.1, 648 at 0.5, 582 at 1, 547 at 2 and 469 mAh g-1 at 4 C (2.85 A g-1), respectively. When cell is returned to 0.1 C, the capacity recovery was still ∼98%. Overall, the electrochemical performance (in terms of cycling stability, high rate capability, and capacity retention) is outstanding and much better than those of the related reported works. Therefore, our smart electrode design enables ZnFe2O4-C sample to be a high quality anode material for lithium-ion batteries.

Preparation of composite electrodes with carbon nanotubes for lithium-ion batteries by low-energy ball milling

Some of the prospective electrode materials for lithium-ion batteries are known to have electronic transport limitations preventing them from being used in the electrodes directly. In many cases, however, these materials may become practical if they are applied in the form of nanocomposites with a carbon component, e.g. via incorporating nanoparticles of the phase of interest into a conducting network of carbon nanotubes. A simple way to prepare oxide-carbon nanotube composites suitable for the electrodes of lithium-ion batteries is presented in this paper. The method is based on low-energy ball milling. An electrochemically active but insulating phase of LiFeTiO4 is used as a test material. It is demonstrated that the LiFeTiO4-carbon nanotube composite is not only capable of having significantly higher capacity (∼105-120 mA h g-1vs. the capacity of ∼65-70 mA h g -1 for the LiFeTiO4 nanoparticles) at a slow current rate but may also operate at reasonably high current rates. © the Partner Organisations 2014.

High-efficient production of boron nitride nanosheets via an optimized ball milling process for lubrication in oil

Although tailored wet ball milling can be an efficient method to produce a large quantity of two-dimensional nanomaterials, such as boron nitride (BN) nanosheets, milling parameters including milling speed, ball-to-powder ratio, milling ball size and milling agent, are important for optimization of exfoliation efficiency and production yield. In this report, we systematically investigate the effects of different milling parameters on the production of BN nanosheets with benzyl benzoate being used as the milling agent. It is found that small balls of 0.1-0.2 mm in diameter are much more effective in exfoliating BN particles to BN nanosheets. Under the optimum condition, the production yield can be as high as 13.8% and the BN nanosheets are 0.5-1.5 μm in diameter and a few nanometers thick and of relative high crystallinity and chemical purity. The lubrication properties of the BN nanosheets in base oil have also been studied. The tribological tests show that the BN nanosheets can greatly reduce the friction coefficient and wear scar diameter of the base oil.

Preparation of cellulose nanofiber from softwood pulp by ball milling

This paper reports the possibility of producing cellulose nanofiber from softwood pulp using a simple ball milling technique under ambient pressure and at room temperature. The effects of milling conditions including the ball-to-cellulose mass ratio, milling time, ball size and alkaline pretreatment were investigated. It was found that milling-ball size should be carefully selected for producing fibrous morphologies instead of particulates. Milling time and ball-to-cellulose mass ratio were also found important to control the fiber morphology. Alkali pre-treatment helped in weakening hydrogen bonds between cellulose fibrils and removing small particles, but with the risks of damaging the fibrous morphology. In a typical run, cellulose nanofiber with an average diameter of 100 nm was obtained using soft mechanical milling conditions using cerium-doped zirconia balls of 0.4–0.6 mm in diameter within 1.5 h without alkaline pretreatment.

Compressibility of a Ti-based alloy with varying amounts of surfactant prepared by high-energy ball milling

The combined effects of varying amounts of surfactant (ethylene bis-stearamide; EBS) and milling time on the compressibility of ball-milled Ti-10Nb-3Mo (wt.%) alloy were investigated. Ball milling process was performed on the elemental powders with different amounts of EBS (0-3. wt.%) for 5 and 10. h, and the ball-milled powders were consolidated by a uniaxial cold pressing in the range of 500-1100. MPa. Results indicated that the addition of surfactant in ball milling process lead to significant changes in particle packing density. The relative density was higher for powders ball milled with larger amounts of EBS and for the shorter milling time. The compressibility of powders was examined by the compaction equation developed by Panelli and Ambrosio Filho. The densification parameter (A) increased with the increasing amount of EBS, and decreased with increasing milling time.

Does playing a sports active video game improve young children's ball skill competence?

OBJECTIVES: Actual and perceived object control (commonly ball) skill proficiency is associated with higher physical activity in children and adolescents. Active video games (AVGs) encourage whole body movement to control/play the electronic gaming system and therefore provide an opportunity for screen time to become more active. The purpose of this study was to determine whether playing sports AVGs has a positive influence on young children's actual and perceived object control skills. DESIGN: Two group pre/post experimental design study. METHODS: Thirty-six children aged 6-10 years old from one school were randomly allocated to a control or intervention condition. The Test of Gross Motor Development-3 assessed object control skill. The Pictorial Scale of Perceived Competence for Young Children assessed perceived object control skill. The intervention consisted of 6×50min lunchtime AVG sessions on the Xbox Kinect. Two to three sport games were chosen for participants to play each session. General linear models with either perceived object control or actual object control skill as the outcome variables were conducted. Each base model adjusted for intervention status and pre-score of the respective outcome variable. Additional models adjusted for potential confounding variables (sex of child and game at home). RESULTS: No significant differences between the control and intervention groups were observed for both outcomes. CONCLUSIONS: This study found that playing the Xbox Kinect does not significantly influence children's perceived or actual object control skills, suggesting that the utility of the Xbox Kinect for developing perceived and actual object control skill competence is questionable.

Simultaneous improvement in the strength and corrosion resistance of Al via high-energy ball milling and Cr alloying

The corrosion resistance and mechanical properties of nanocrystalline aluminium (Al) and Al-20. wt.%Cr alloys, synthesized by high-energy ball milling followed by spark plasma sintering, were investigated. Both alloys exhibited an excellent combination of corrosion resistance and compressive yield strength, which was attributed to the nanocrystalline structure, extended solubility, uniformly distributed fine particles, and homogenous microstructure induced by high-energy ball milling. This work demonstrates the possibilities of developing ultra-high strength Al alloys with excellent corrosion resistance, exploiting conventionally insoluble elements or alloying additions via suitable processing routes.