Articulated wooden blades for a horizontal-axis wind turbine. Design, construction and testing.

A pair of blades were constructed following a Tapered Chord, Zero Twist pattern after Anderson. The construction uses the Wood Epoxy Saturation Technique, with a solid Beech main spar and leading edge joined together with laminated veneers of beech forming a D-section; the trailing edge is formed from millimetre ply skins, foam filled to resist compressive loads. This construction leads to an extremely light, flexible blade, with the centres of gravity and torsion well forward, giving good stability. Each blade has three built-in strain gauges, alowing flapwise bending to be measured. Stiffness, and natural frequencies, were measured, to input to a numerical computer model to calculate blade deformation during operation, and to determine stability boundaries of the blade. Preliminary aerodynamic performance measurements are presented and close agreement is found with theory.

Cultivation of Gracilaria lichenoides in Puttalam Lagoon

A brief description is given of experimental rearing of the red alga G. lichenoides using a coir net frame method. Frames of 1x1 m were made and tied to bamboo poles which were planted in water; the frame was fixed at a level about 1 ft below the water level. 2 cm fragments were used as propagating material. Plants were found to grow more luxuriantly and were more greenish than using other methods, and in addition were free from extraneous matter such as sand. The regeneration time of the plant is low, and it reaches marketable size in 3-4 months.

A packaging technique for silicon MEMS strain sensors on steel

A packaging technique suited to applying MEMS strain sensors realized on a silicon chip to a steel flat surface is described. The method is based on adhesive bonding of the silicon chip rear surface on steel using two types of glue normally used for standard piezoresistive strain sensors (Mbond200/ 600), using direct wire bonding of the chip to a Printed Circuit Board, also fixed on steel. In order to protect the sensor from the external environment, and to improve the MEMS performance, the silicon chip is encapsulated with a metal cap hermetically sealed-off under vacuum condition with a vacuum adhesive in which the bonding wires are also protected from possible damage. In order to evaluate the mechanical coupling of the silicon chip with the bar and thestress transfer extent to the silicon surface, commercial strain sensors have been applied on the chip glued on a steel bar in alaboratory setup able to generate strain by inflection, yielding a stress transfer around 70% from steel to silicon. © 2008 IEEE.

Effects of black Bengal goat manure on growth and production of Genetically Improved Farmed Tilapia (GIFT) starin [sic], Oreochromis niloticus

In a goat-tilapia integrated farming system, the effect of Black Bengal goat manure on the growth and production of Oreochromis niloticus was studied at the Freshwater Substation, Shantahar, Bogra for 4.5 months. The stocking density used in three treatments were, 200 goats and 15,000 GIFT strain/ha (T1); 300 goats and 15,000 GIFT strain/ha (T2); and only 15,000 GIFT strain/ha (T3). The initial individual total length and weight of stocked tilapia were 7.6 cm and 11.34 g, respectively. Twelve ponds each having an area of 40 square meters were used for this trail [sic]. On one side of each pond goat shed was constructed and the space allocated for each goat was 0.75 m x 1.5 m. Newly weaned black Bengal goats of average weight 8.45 kg was used in the trial. Every morning the goats manure was swiped out in ponds through the fixed opening of bamboo made floor of goat shed. Water depth of the ponds was maintained at 0.75 m. The highest fish production was in treatment 1 (1,750 kg/ha) followed by treatment 2 (1,455 kg/ha) and treatment 3 (621 kg/ha). The difference in individual goat weight was not significant (P>0.05) among treatments 1 and 2.

Comparative study of traditional and improved containers for transportation of fresh fish

Traditional bamboo basket and expanded polystyrene insulated plywood box (second hand tea-chest) were compared for transportation of iced marine, fresh water and brackish water fishes from Kakinada to Madras by rail. Quality of fish at dispatching and receiving centres was assessed by organoleptic, total volatile nitrogen (TVN) and total bacterial count (TBC) tests. Based on the results obtained and the prices fetched, the traditional bamboo basket apart from being cheaper was found to be as good as expanded polystyrene insulated plywood box for short distance transportation of iced fish involving less than 24 hours journey.

The preservation of some Indian freshwater fish

Quality changes in Labeo rohita, Cirrhinus mrigala and Tilapia mossambica were studied during storage in ice and at ambient temperature (29-32°C). After 10h at ambient temperature L. rohita and T. mossambica were completely spoiled, while C. mrigala became unacceptable within 11h. Organoleptic examination, total volatile base nitrogen and total bacterial counts showed that L. rohita (0.5 kg and above) and C. mrigala (0.5 kg and above) were acceptable up to 7 to 8 days of storage in ice in popular container (Bamboo basket) lined with palmyrah mat) at ambient temperature while T. mossambica (30-40 g) was acceptable up to 6 days. Influence of size of fish on shelf life in ice studied with reference to L. rohita showed that fishes below 500 g were acceptable up to 6 days of storage in ice in popular container at ambient temperature while those above 1000 g size were acceptable up to 8 days. Provision of an alkathene lining to the popular container extended the storage life of L. rohita from 6 days to 8 days. Pre-chilled and iced L. rohita had a longer shel flife (9 days) than merely iced sample (7 days).

Bulk packages for storage and transportation of salted and dried fish

The effect of bulk packaging on the storage of salted and dried fish was studied at ambient conditions. Four different packaging systems were tried, among which gusseted type high density polyethylene woven sacks having either circular loom or traditional loom laminated with 100 gauge low density polyethylene were found to be best suited for dry fish packaging as they could withstand the hazards of handling, transportation and storage.

The sequence and de novo assembly of the giant panda genome

Using next-generation sequencing technology alone, we have successfully generated and assembled a draft sequence of the giant panda genome. The assembled contigs (2.25 gigabases (Gb)) cover approximately 94% of the whole genome, and the remaining gaps (0.05 Gb) seem to contain carnivore-specific repeats and tandem repeats. Comparisons with the dog and human showed that the panda genome has a lower divergence rate. The assessment of panda genes potentially underlying some of its unique traits indicated that its bamboo diet might be more dependent on its gut microbiome than its own genetic composition. We also identified more than 2.7 million heterozygous single nucleotide polymorphisms in the diploid genome. Our data and analyses provide a foundation for promoting mammalian genetic research, and demonstrate the feasibility for using next-generation sequencing technologies for accurate, cost-effective and rapid de novo assembly of large eukaryotic genomes.

Comparative feature on design, construction and installation of three different model of low cost solar tunnel dryers

The study was conducted in collaboration with the ECFC project of the FAO (BGD/97/017) in Cox's Bazar to develop a low cost solar tunnel dryer for the production of high quality marine dried fish. The study areas were Kutubdiapara, Maheshkhali and Shahparirdip under Cox's Bazar district. Three different models of low cost solar dryer were constructed with locally available materials such as bamboo, wood, bamboo mat, hemp, canvas, wire, nails, rope, tin, polythene and net. Size of the dryers were: 20x4x3 ft ; 30x3x3 ft and 65x3x3 ft with the costs of Tk. 3060, 3530, 9600 for dryer 1, 2 and 3, respectively having different models. The drying capacities were 50, 150, 500 kg for dryer 1, 2 and 3 respectively. The average temperature range inside the dryers were 29-43°C, 34-51°C and 37-57°C for dryer 1, 2 and 3 respectively as recorded at 8:30h to 16:30h. The relative humidity were in the ranges of 22-42%, 27-39% and 24-41 % in dryer 1, 2 and 3 respectively. The fish samples used were Bombay duck, Silver Jew fish and Ribbon fish. The total drying time was in the range of 30-42, 28-38 and 24-34 hours to reach the moisture content of 12.3-14.5, 11.8-14.3, and 11.6-14.1% in dryer 1, 2 and 3 respectively. Among these three fish samples the drying was faster in Silver Jew fish followed by Bombay duck and Ribbon fish in all the three dryer.

Effect of delayed icing on the quality of tiger shrimp (Penaeus monodon Fab.)

Effect of delayed icing on the quality of Penaeus monodon iced after three hours of harvest was studied in plastic and bamboo baskets. After harvest of three hours at ambient temperature (28°-32°C), ice was added to the shrimp at a ratio of 1:1 (shrimp:ice) and stored for 21 hours in both the baskets. Quality evaluation was carried out through visual assessment, biochemical analysis and microbial analysis for 24 hours. The organoleptic evaluation and scoring was done from the time of harvest treated as 0 hour and the average score was 10. At 9th hour after iced condition quality of shrimp was found reduced to the next stage (acceptable) with a score ranged from 8.4-6.5 in both baskets. This acceptable stage was observed throughout the experiment for bamboo basket whereas in the plastic basket the quality was reduced to a small extent with a score of 6.4 (moderately acceptable). Till the end point of the experiment the quality of shrimp was acceptable in respect to biochemical analysis. The microbial load was found log sub(10) 3.99±0.12 cfu/g to log sub(10) 4.33±0.21 cfu/g and log sub(10) 4.01 ±0.12 cfu/g to log sub(10) 4.83±0.19 cfu/g in the bamboo and plastic basket respectively. The importers or buyers suggests for immediate icing to maintain good quality but results of the present experiment suggest that the quality does not vary drastically for first three hours.

NATURAL FOODS AND THEIR ECOLOGICAL IMPLICATIONS FOR MACACA-THIBETANA AT MOUNT EMEI, CHINA

Natural food plants of partly provisioned groups of Macaca thibetana included about 196 species belonging to 135 genera and 72 families. The macaques consumed mainly bamboo shoots and fruits for about 2 months in autumn, whereas they relied on active or passive provisions from visitors, a variety of structural parts of plants and a small amount of invertebrates in late spring and summer and ate mainly mature leaves and bark for the rest of the year. About half of the species eaten came from the dense herb and shrub layers. This forest-dwelling species shows a distinctive feeding and foraging pattern in comparison with other macaques, explaining why M. thibetana has the largest body weight of all macaques.

滇金丝猴栖息地竹类资源及群落学特征

对滇金丝猴栖息地60条样线和15个调查点的实地调查表明,箭竹是林下植被的主要组成部分,所处的主要群落有云南铁杉-卵叶杜鹃林,长苞冷杉-亮叶杜鹃林,白柯-假乳黄杜鹃林,西南桦-五裂枫林,黄背栎林,华山松-麻栎林等。栖息地内的多数箭竹是滇金丝猴夏季的主要食物种类之一,箭竹属植物资源对保护金丝猴具有重要意义。

Sleeping sites of Rhinopithecus bieti at Mt. Fuhe, Yunnan

Data on sleeping site selection were collected for a group of black-and-white snub-nosed monkeys (Rhinopithecus bieti; around 80) at Mt. Fuhe, Yunnan, China (99degrees20'E, 26degrees25'N, about 3,000 m asl) from November 2000 to January 2002. At the site mainly three vegetation types were present in an elevation-ascending order: deciduous broad leaf forest, mixed coniferous and broad leaf forest, and dark coniferous forest. In addition, bamboo forest presented in areas burned in 1958. Sleeping sites (n = 10) were located in the coniferous forest, where trees were the tallest, bottommost branches were the highest, the diameter of crowns was the second largest, and the gradient of the ground was the steepest. Monkeys usually kept quiet during entering and staying at a sleeping site. The site choice and the quietness may be tactics to avoid potential predators. In the coniferous forest, however, monkeys did not sleep in the valley bottom where trees were the largest, but frequently slept in the middle of the slope towards the east/southeast, in the shadow of ridges in three other directions, to avoid strong wind and to access sunshine; in winter-spring, they ranged in a more southern and lower area than in summer-autumn. These may be behavioral strategies to minimize energy stress in the cold habitat. Monkeys often slept in the same sleeping site on consecutive nights, which reflected a reduced pressure of predation probably due to either the effectiveness of anti-predation through sleeping site selection, or the population decline of predators with increasing human activities in the habitat. The group's behavioral responses to interactive and sometimes conflicting traits of the habitat are site-specific and conform to expectations for a temperate zone primate.

The soft impact response of composite laminate beams

The quasi-static and dynamic responses of laminated beams of equal areal mass, made from monolithic CFRP and Ultra high molecular weight Polyethylene (UHMWPE), have been measured. The end-clamped beams were impacted at mid-span by metal foam projectiles to simulate localised blast loading. The effect of clamping geometry on the response was investigated by comparing the response of beams bolted into the supports with the response of beams whose ends were wrapped around the supports. The effect of laminate shear strength upon the static and dynamic responses was investigated by testing two grades of each of the CFRP and UHMWPE beams: (i) CFRP beams with a cured matrix and uncured matrix, and (ii) UHMWPE laminates with matrices of two different shear strengths. Quasi-static stretch-bend tests indicated that the load carrying capacity of the UHWMPE beams exceeds that of the CFRP beams, increases with diminishing shear strength of matrix, and increases when the ends are wrapped rather than through-bolted. The dynamic deformation mode of the beams is qualitatively different from that observed in the quasi-static stretch-bend tests. In the dynamic case, travelling hinges emanate from the impact location and propagate towards the supports; the beams finally fail by tensile fibre fracture at the supports. The UHMWPE beams outperform the CFRP beams in terms of a lower mid-span deflection for a given impulse, and a higher failure impulse. Also, the maximum attainable impulse increases with decreasing shear strength for both the UHMWPE and CFRP beams. The ranking of the beams for load carrying capacity in the quasi-static stretch-bend tests is identical to that for failure impulse in the impact tests. Thus, the static tests can be used to gauge the relative dynamic performances of the beams. © 2013 Elsevier Ltd. All rights reserved.

Glass reinforced glass

Laminated glass units are traditionally used to provide a degree of post-fracture strength, but the residual strength is often limited to relatively low levels suffi cient for holding the glass fragments together for a predetermined amount of time. It is possible to achieve a higher level of residual strength, but this requires specific boundary conditions and/or opaque reinforcing materials. This paper describes the experimental investigations on laminated glass units that can provide a signifi cant degree of post-fracture resistance, without the need of boundary restraints or opaque reinforcing materials. The glass units are composed entirely of combinations of conventional transparent interlayers and commercially available glass (annealed, heat treated and chemically strengthened). The paper also describes an empirical energy based interpretation of the mechanical response of the laminated units.