Examination of the quality of spinach leaves using hyperspectral imaging

The present research is focused on the application of hyperspectral images for the supervision of quality deterioration in ready to use leafy spinach during storage (Spinacia oleracea). Two sets of samples of packed leafy spinach were considered: (a) a first set of samples was stored at 20 °C (E-20) in order to accelerate the degradation process, and these samples were measured the day of reception in the laboratory and after 2 days of storage; (b) a second set of samples was kept at 10 °C (E-10), and the measurements were taken throughout storage, beginning the day of reception and repeating the acquisition of Images 3, 6 and 9 days later. Twenty leaves per test were analyzed. Hyperspectral images were acquired with a push-broom CCD camera equipped with a spectrograph VNIR (400–1000 nm). Calibration set of spectra was extracted from E-20 samples, containing three classes of degradation: class A (optimal quality), class B and class C (maximum deterioration). Reference average spectra were defined for each class. Three models, computed on the calibration set, with a decreasing degree of complexity were compared, according to their ability for segregating leaves at different quality stages (fresh, with incipient and non-visible symptoms of degradation, and degraded): spectral angle mapper distance (SAM), partial least squares discriminant analysis models (PLS-DA), and a non linear index (Leafy Vegetable Evolution, LEVE) combining five wavelengths were included among the previously selected by CovSel procedure. In sets E-10 and E-20, artificial images of the membership degree according to the distance of each pixel to the reference classes, were computed assigning each pixel to the closest reference class. The three methods were able to show the degradation of the leaves with storage time.

Caracterización automatizada de texturas de menas mediante análisis digital de imagen para su aplicación geometalúrgica

La mineralogía de procesos se ha convertido en los últimos años en una herramienta indispensable dentro del ámbito minero-metalúrgico debido fundamentalmente a la emergencia de la Geometalurgia. Esta disciplina en auge, a través de la integración de datos geológicos, mineros y metalúrgicos, proporciona la información necesaria para que el circuito de concentración mineral pueda responder de manera rápida y eficaz a la variabilidad mineralógica inherente a la geología del yacimiento. Para la generación del modelo geometalúrgico, la mineralogía de procesos debe aportar datos cuantitativos sobre los rasgos mineralógicos influyentes en el comportamiento de los minerales y para ello se apoya en el uso de sistemas de análisis mineralógico automatizado. Estos sistemas son capaces de proporcionar gran cantidad de datos mineralógicos de manera rápida y precisa. Sin embargo, cuando se trata de la caracterización de la textura, el mineralogista debe recurrir a descripciones cualitativas basadas en la observación, ya que los sistemas actuales no ofrecen información textural automatizada. Esta tesis doctoral surge precisamente para proporcionar de manera sistemática información textural relevante para los procesos de concentración mineral. La tesis tiene como objetivo principal la identificación y caracterización del tipo de intercrecimiento que un determinado mineral presenta en las partículas minerales, e inicialmente se han tenido en cuenta los siete tipos de intercrecimiento considerados como los más relevantes bajo el punto de vista del comportamiento de las partículas minerales durante flotación, lixiviación y molienda. Para alcanzar este objetivo se ha desarrollado una metodología basada en el diseño y cálculo de una serie de índices numéricos, a los que se ha llamado índices mineralúrgicos, que cumplen una doble función: por un lado, cada índice aporta información relevante para caracterizar los principales rasgos mineralógicos que gobiernan el comportamiento de las partículas minerales a lo largo de los procesos de concentración y por otro lado, estos índices sirven como variables discriminantes para identificar el tipo de intercrecimiento mineral mediante la aplicación de Análisis Discriminante. Dentro del conjunto de índices propuestos en este trabajo, se han considerado algunos índices propuestos por otros autores para su aplicación tanto en el ámbito de la mineralogía como en otros ámbitos de la ciencia de materiales. Se trata del Índice de Contigüidad (Gurland, 1958), Índice de Intercrecimiento (Amstutz y Giger, 1972) e Índice de Coordinación (Jeulin, 1981), adaptados en este caso para el análisis de partículas minerales. El diseño de los índices se ha basado en los principios básicos de la Estereología y el análisis digital de imagen, y su cálculo se ha llevado a cabo aplicando el método de interceptos lineales mediante la programación en MATLAB de varias rutinas. Este método estereológico permite recoger una serie de medidas a partir de las que es posible calcular varios parámetros, tanto estereológicos como geométricos, que han servido de base para calcular los índices mineralúrgicos. Para evaluar la capacidad discriminatoria de los índices mineralúrgicos se han seleccionado 200 casos en los que se puede reconocer de manera clara alguno de los siete tipos de intercrecimiento considerados inicialmente en este trabajo. Para cada uno de estos casos se han calculado los índices mineralúrgicos y se ha aplicado Análisis Discriminante, obteniendo un porcentaje de acierto en la clasificación del 95%. Esta cifra indica que los índices propuestos son discriminadores fiables del tipo de intercrecimiento. Una vez probada la capacidad discriminatoria de los índices, la metodología desarrollada ha sido aplicada para caracterizar una muestra de un concentrado de cobre procedente de la mina Kansanshi (Zambia). Esta caracterización se ha llevado a cabo para obtener la distribución de calcopirita según su tipo de intercrecimiento. La utilidad de esta distribución ha sido analizada bajo diferentes puntos de vista y en todos ellos los índices mineralúrgicos aportan información valiosa para caracterizar el comportamiento mineralúrgico de las partículas minerales. Los resultados derivados tanto del Análisis Discriminante como de la caracterización del concentrado de Kansanshi muestran la fiabilidad, utilidad y versatilidad de la metodología desarrollada, por lo que su integración como herramienta rutinaria en los sistemas actuales de análisis mineralógico pondría a disposición del mineralurgista gran cantidad de información textural complementaria a la información ofrecida por las técnicas actuales de caracterización mineralógica. ABSTRACT Process mineralogy has become in the last decades an essential tool in the mining and metallurgical sphere, especially driven by the emergence of Geometallurgy. This emergent discipline provides required information to efficiently tailor the circuit performance to the mineralogical variability inherent to ore deposits. To contribute to the Geometallurgical model, process mineralogy must provide quantitative data about the main mineralogical features implied in the minerallurgical behaviour of minerals. To address this characterisation, process mineralogy relies on automated systems. These systems are capable of providing a large amount of data quickly and accurately. However, when it comes to the characterisation of texture, mineralogists need to turn to qualitative descriptions based on observation, due to the fact that current systems can not offer quantitative textural information in a routine way. Aiming at the automated characterisation of textural information, this doctoral thesis arises to provide textural information relevant for concentration processes in a systematic way. The main objective of the thesis is the automated identification and characterisation of intergrowth types in mineral particles. Initially, the seven intergrowth types most relevant for flotation, leaching and grinding are considered. To achieve this goal, a methodology has been developed based on the computation of a set of numerical indices, which have been called minerallurgical indices. These indices have been designed with two main purposes: on the one hand, each index provides information to characterise the main mineralogical features which determine particle behaviour during concentration processes and, on the other hand, these indices are used as discriminant variables for identifying the intergrowth type by Discriminant Analysis. Along with the indices developed in this work, three indices proposed by other authors belonging to different fields of materials science have been also considered after being adapted to the analysis of mineral particles. These indices are Contiguity Index (Gurland, 1958), Intergrowth Index (Amstutz and Giger, 1972) and Coordination Index (Jeulin, 1981). The design of minerallurgical indices is based on the fundamental principles of Stereology and Digital Image Analysis. Their computation has been carried out using the linear intercepts method, implemented by means of MATLAB programming. This stereological method provides a set of measurements to obtain several parameters, both stereological and geometric. Based on these parameters, minerallurgical indices have been computed. For the assessment of the discriminant capacity of the developed indices, 200 cases have been selected according to their internal structure, so that one of the seven intergrowth types initially considered in this work can be easily recognised in any of their constituents. Minerallurgical indices have been computed for each case and used as discriminant variables. After applying discriminant analysis, 95% of the cases were correctly classified. This result shows that the proposed indices are reliable identifiers of intergrowth type. Once the discriminant power of the indices has been assessed, the developed methodology has been applied to characterise a copper concentrate sample from the Kansanshi copper mine (Zambia). This characterisation has been carried out to quantify the distribution of chalcopyrite with respect to intergrowth types. Different examples of the application of this distribution have been given to test the usefulness of the method. In all of them, the proposed indices provide valuable information to characterise the minerallurgical behaviour of mineral particles. Results derived from both Discriminant Analysis and the characterisation of the Kansanshi concentrate show the reliability, usefulness and versatility of the developed methodology. Therefore, its integration as a routine tool in current systems of automated mineralogical analysis should make available for minerallurgists a great deal of complementary information to treat the ore more efficiently.

Optical detection of mealiness in apples using laser TDRS.

Mealiness is a textural attribute related to an internal fruit disorder that involves quality loss. It is characterised by the combination of abnormal softness of the fruit and absence of free juiciness in the mouth when eaten by the consumer. Recent research concluded with the development of precise instrumental procedure to measure a scale of mealiness based on the combination of several rheological properties and empirical magnitudes. In this line, time-domain laser reflectance spectroscopy (TDRS) is a new medical technology, used to characterise the optical properties of tissues, and to locate affected areas like tumours. Among its advantages compared to more traditional spectroscopic techniques, there is the feasibility to asses simultaneously and independently two optical parameters: the absorption of the light inside the irradiated body, and the scattering of the photons across the tissues, at each wavelength, generating two coefficients (µa, absorption coeff.; and µ's, transport scattering coeff.). If it is assumed that they are related respectively to chemical components and to physical properties of the sample, TDRS can be applied to the quantification of chemicals and the measurement of the rheological properties (i.e. mealiness estimation) at the same time. Using VIS & NIR lasers as light sources, TDRS was applied in this work to Golden Delicious and Cox apples (n=90), conforming several batches of untreated samples and storage-treated (20°C & 95%RH) to promote the development of mealiness. The collected database was clustered into different groups according to their instrumental test values (Barreiro et al, 1998). The optical coefficients were used as explanatory variables when building discriminant analysis functions for mealiness, achieving a classification score above 80% of correctly identified mealy versus fresh apples.

Automated characterisation of intergrowth textures in mineral particles. A case study

The characterisation of mineral texture has been a major concern for process mineralogists, as liberation characteristics of the ores are intimately related to the mineralogical texture. While a great effort has been done to automatically characterise texture in unbroken ores, the characterisation of textural attributes in mineral particles is usually descriptive. However, the quantitative characterisation of texture in mineral particles is essential to improve and predict the performance of minerallurgical processes (i.e. all the processes involved in the liberation and separation of the mineral of interest) and to achieve a more accurate geometallurgical model. Driven by this necessity of achieving a more complete characterisation of textural attributes in mineral particles, a methodology has been recently developed to automatically characterise the type of intergrowth between mineral phases within particles by means of digital image analysis. In this methodology, a set ofminerallurgical indices has been developed to quantify different mineralogical features and to identify the intergrowth pattern by discriminant analysis. The paper shows the application of the methodology to the textural characterisation of chalcopyrite in the rougher concentrate of the Kansanshi copper mine (Zambia). In this sample, the variety of intergrowth patterns of chalcopyrite with the other minerals has been used to illustrate the methodology. The results obtained show that the method identifies the intergrowth type and provides quantitative information to achieve a complete and detailed mineralogical characterisation. Therefore, the use of this methodology as a routinely tool in automated mineralogy would contribute to a better understanding of the ore behaviour during liberation and separation processes.

Multiple proportion case-basing driven CBRE and its application in the evaluation of possible failure of firms

Case-based reasoning (CBR) is a unique tool for the evaluation of possible failure of firms (EOPFOF) for its eases of interpretation and implementation. Ensemble computing, a variation of group decision in society, provides a potential means of improving predictive performance of CBR-based EOPFOF. This research aims to integrate bagging and proportion case-basing with CBR to generate a method of proportion bagging CBR for EOPFOF. Diverse multiple case bases are first produced by multiple case-basing, in which a volume parameter is introduced to control the size of each case base. Then, the classic case retrieval algorithm is implemented to generate diverse member CBR predictors. Majority voting, the most frequently used mechanism in ensemble computing, is finally used to aggregate outputs of member CBR predictors in order to produce final prediction of the CBR ensemble. In an empirical experiment, we statistically validated the results of the CBR ensemble from multiple case bases by comparing them with those of multivariate discriminant analysis, logistic regression, classic CBR, the best member CBR predictor and bagging CBR ensemble. The results from Chinese EOPFOF prior to 3 years indicate that the new CBR ensemble, which significantly improved CBRs predictive ability, outperformed all the comparative methods.

Mulch materials in processing tomato: a multivariate approach.

Mulch materials of different origins have been introduced into the agricultural sector in recent years alternatively to the standard polyethylene due to its environmental impact. This study aimed to evaluate the multivariate response of mulch materials over three consecutive years in a processing tomato (Solanum lycopersicon L.) crop in Central Spain. Two biodegradable plastic mulches (BD1, BD2), one oxo-biodegradable material (OB), two types of paper (PP1, PP2), and one barley straw cover (BS) were compared using two control treatments (standard black polyethylene [PE] and manual weed control [MW]). A total of 17 variables relating to yield, fruit quality, and weed control were investigated. Several multivariate statistical techniques were applied, including principal component analysis, cluster analysis, and discriminant analysis. A group of mulch materials comprised of OB and BD2 was found to be comparable to black polyethylene regarding all the variables considered. The weed control variables were found to be an important source of discrimination. The two paper mulches tested did not share the same treatment group membership in any case: PP2 presented a multivariate response more similar to the biodegradable plastics, while PP1 was more similar to BS and MW. Based on our multivariate approach, the materials OB and BD2 can be used as an effective, more environmentally friendly alternative to polyethylene mulches.

Age regression from soft aligned face images using low computational resources

The initial step in most facial age estimation systems consists of accurately aligning a model to the output of a face detector (e.g. an Active Appearance Model). This fitting process is very expensive in terms of computational resources and prone to get stuck in local minima. This makes it impractical for analysing faces in resource limited computing devices. In this paper we build a face age regressor that is able to work directly on faces cropped using a state-of-the-art face detector. Our procedure uses K nearest neighbours (K-NN) regression with a metric based on a properly tuned Fisher Linear Discriminant Analysis (LDA) projection matrix. On FG-NET we achieve a state-of-the-art Mean Absolute Error (MAE) of 5.72 years with manually aligned faces. Using face images cropped by a face detector we get a MAE of 6.87 years in the same database. Moreover, most of the algorithms presented in the literature have been evaluated on single database experiments and therefore, they report optimistically biased results. In our cross-database experiments we get a MAE of roughly 12 years, which would be the expected performance in a real world application.

Descripción de parámetros glóticos basados en el modelado de los pliegues vocales para la detección de patología de la voz

Las patologías de la voz se han transformado en los últimos tiempos en una problemática social con cierto calado. La contaminación de las ciudades, hábitos como el de fumar, el uso de aparatos de aire acondicionado, etcétera, contribuyen a ello. Esto alcanza más relevancia en profesionales que utilizan su voz de manera frecuente, como, por ejemplo, locutores, cantantes, profesores o teleoperadores. Por todo ello resultan de especial interés las técnicas de ayuda al diagnóstico que son capaces de extraer conclusiones clínicas a partir de una muestra de la voz grabada con un micrófono, frente a otras invasivas que implican la exploración utilizando laringoscopios, fibroscopios o videoendoscopios, técnicas en cualquier caso mucho más molestas para los pacientes al exigir la introducción parcial del instrumental citado por la garganta, en actuaciones consideradas de tipo quirúrgico. Dentro de aquellas técnicas se ha avanzado mucho en un período de tiempo relativamente corto. En lo que se refiere al diagnóstico de patologías, hemos pasado en los últimos quince años de trabajar principalmente con parámetros extraídos de la señal de voz –tanto en el dominio del tiempo como en el de la frecuencia– y con escalas elaboradas con valoraciones subjetivas realizadas por expertos a hacerlo también con parámetros procedentes de estimaciones de la fuente glótica. La importancia de utilizar la fuente glótica reside, a grandes rasgos, en que se trata de una señal vinculada directamente al estado de la estructura laríngea del locutor y también en que está generalmente menos influida por el tracto vocal que la señal de voz. Es conocido que el tracto vocal guarda más relación con el mensaje hablado, y su presencia dificulta el proceso de detección de patología vocal. Estas estimaciones de la fuente glótica han sido obtenidas a través de técnicas de filtrado inverso desarrolladas por nuestro grupo de investigación. Hemos conseguido, además, profundizar en la naturaleza de la señal glótica: somos capaces de descomponerla y relacionarla con parámetros biomecánicos de los propios pliegues vocales, obteniendo estimaciones de elementos como la masa, la pérdida de energía o la elasticidad del cuerpo y de la cubierta del pliegue, entre otros. De las componentes de la fuente glótica surgen también los denominados parámetros biométricos, relacionados con la forma de la señal, que constituyen por sí mismos una firma biométrica del individuo. También trabajaremos con parámetros temporales, relacionados con las diferentes etapas que se observan dentro de la señal glótica durante un ciclo de fonación. Por último, consideraremos parámetros clásicos de perturbación y energía de la señal. En definitiva, contamos ahora con una considerable cantidad de parámetros glóticos que conforman una base estadística multidimensional, destinada a ser capaz de discriminar personas con voces patológicas o disfónicas de aquellas que no presentan patología en la voz o con voces sanas o normofónicas. Esta tesis doctoral se ocupa de varias cuestiones: en primer lugar, es necesario analizar cuidadosamente estos nuevos parámetros, por lo que ofreceremos una completa descripción estadística de los mismos. También estudiaremos cuestiones como la distribución de los parámetros atendiendo a criterios como el de normalidad estadística de los mismos, ocupándonos especialmente de la diferencia entre las distribuciones que presentan sujetos sanos y sujetos con patología vocal. Para todo ello emplearemos diferentes técnicas estadísticas: generación de elementos y diagramas descriptivos, pruebas de normalidad y diversos contrastes de hipótesis, tanto paramétricos como no paramétricos, que considerarán la diferencia entre los grupos de personas sanas y los grupos de personas con alguna patología relacionada con la voz. Además, nos interesa encontrar relaciones estadísticas entre los parámetros, de cara a eliminar posibles redundancias presentes en el modelo, a reducir la dimensionalidad del problema y a establecer un criterio de importancia relativa en los parámetros en cuanto a su capacidad discriminante para el criterio patológico/sano. Para ello se aplicarán técnicas estadísticas como la Correlación Lineal Bivariada y el Análisis Factorial basado en Componentes Principales. Por último, utilizaremos la conocida técnica de clasificación Análisis Discriminante, aplicada a diferentes combinaciones de parámetros y de factores, para determinar cuáles de ellas son las que ofrecen tasas de acierto más prometedoras. Para llevar a cabo la experimentación se ha utilizado una base de datos equilibrada y robusta formada por doscientos sujetos, cien de ellos pertenecientes al género femenino y los restantes cien al género masculino, con una proporción también equilibrada entre los sujetos que presentan patología vocal y aquellos que no la presentan. Una de las aplicaciones informáticas diseñada para llevar a cabo la recogida de muestras también es presentada en esta tesis. Los distintos estudios estadísticos realizados nos permitirán identificar aquellos parámetros que tienen una mayor contribución a la hora de detectar la presencia de patología vocal. Alguno de los estudios, además, nos permitirá presentar una ordenación de los parámetros en base a su importancia para realizar la detección. Por otra parte, también concluiremos que en ocasiones es conveniente realizar una reducción de la dimensionalidad de los parámetros para mejorar las tasas de detección. Por fin, las propias tasas de detección constituyen quizá la conclusión más importante del trabajo. Todos los análisis presentes en el trabajo serán realizados para cada uno de los dos géneros, de acuerdo con diversos estudios previos que demuestran que los géneros masculino y femenino deben tratarse de forma independiente debido a las diferencias orgánicas observadas entre ambos. Sin embargo, en lo referente a la detección de patología vocal contemplaremos también la posibilidad de trabajar con la base de datos unificada, comprobando que las tasas de acierto son también elevadas. Abstract Voice pathologies have become recently in a social problem that has reached a certain concern. Pollution in cities, smoking habits, air conditioning, etc. contributes to it. This problem is more relevant for professionals who use their voice frequently: speakers, singers, teachers, actors, telemarketers, etc. Therefore techniques that are capable of drawing conclusions from a sample of the recorded voice are of particular interest for the diagnosis as opposed to other invasive ones, involving exploration by laryngoscopes, fiber scopes or video endoscopes, which are techniques much less comfortable for patients. Voice quality analysis has come a long way in a relatively short period of time. In regard to the diagnosis of diseases, we have gone in the last fifteen years from working primarily with parameters extracted from the voice signal (both in time and frequency domains) and with scales drawn from subjective assessments by experts to produce more accurate evaluations with estimates derived from the glottal source. The importance of using the glottal source resides broadly in that this signal is linked to the state of the speaker's laryngeal structure. Unlike the voice signal (phonated speech) the glottal source, if conveniently reconstructed using adaptive lattices, may be less influenced by the vocal tract. As it is well known the vocal tract is related to the articulation of the spoken message and its influence complicates the process of voice pathology detection, unlike when using the reconstructed glottal source, where vocal tract influence has been almost completely removed. The estimates of the glottal source have been obtained through inverse filtering techniques developed by our research group. We have also deepened into the nature of the glottal signal, dissecting it and relating it to the biomechanical parameters of the vocal folds, obtaining several estimates of items such as mass, loss or elasticity of cover and body of the vocal fold, among others. From the components of the glottal source also arise the so-called biometric parameters, related to the shape of the signal, which are themselves a biometric signature of the individual. We will also work with temporal parameters related to the different stages that are observed in the glottal signal during a cycle of phonation. Finally, we will take into consideration classical perturbation and energy parameters. In short, we have now a considerable amount of glottal parameters in a multidimensional statistical basis, designed to be able to discriminate people with pathologic or dysphonic voices from those who do not show pathology. This thesis addresses several issues: first, a careful analysis of these new parameters is required, so we will offer a complete statistical description of them. We will also discuss issues such as distribution of the parameters, considering criteria such as their statistical normality. We will take special care in the analysis of the difference between distributions from healthy subjects and the distributions from pathological subjects. To reach these goals we will use different statistical techniques such as: generation of descriptive items and diagramas, tests for normality and hypothesis testing, both parametric and nonparametric. These latter techniques consider the difference between the groups of healthy subjects and groups of people with an illness related to voice. In addition, we are interested in finding statistical relationships between parameters. There are various reasons behind that: eliminate possible redundancies in the model, reduce the dimensionality of the problem and establish a criterion of relative importance in the parameters. The latter reason will be done in terms of discriminatory power for the criterion pathological/healthy. To this end, statistical techniques such as Bivariate Linear Correlation and Factor Analysis based on Principal Components will be applied. Finally, we will use the well-known technique of Discriminant Analysis classification applied to different combinations of parameters and factors to determine which of these combinations offers more promising success rates. To perform the experiments we have used a balanced and robust database, consisting of two hundred speakers, one hundred of them males and one hundred females. We have also used a well-balanced proportion where subjects with vocal pathology as well as subjects who don´t have a vocal pathology are equally represented. A computer application designed to carry out the collection of samples is also presented in this thesis. The different statistical analyses performed will allow us to determine which parameters contribute in a more decisive way in the detection of vocal pathology. Therefore, some of the analyses will even allow us to present a ranking of the parameters based on their importance for the detection of vocal pathology. On the other hand, we will also conclude that it is sometimes desirable to perform a dimensionality reduction in order to improve the detection rates. Finally, detection rates themselves are perhaps the most important conclusion of the work. All the analyses presented in this work have been performed for each of the two genders in agreement with previous studies showing that male and female genders should be treated independently, due to the observed functional differences between them. However, with regard to the detection of vocal pathology we will consider the possibility of working with the unified database, ensuring that the success rates obtained are also high.

Estimación eficiente de atributos demográficos del rostro humano en imágenes

Sin duda, el rostro humano ofrece mucha más información de la que pensamos. La cara transmite sin nuestro consentimiento señales no verbales, a partir de las interacciones faciales, que dejan al descubierto nuestro estado afectivo, actividad cognitiva, personalidad y enfermedades. Estudios recientes [OFT14, TODMS15] demuestran que muchas de nuestras decisiones sociales e interpersonales derivan de un previo análisis facial de la cara que nos permite establecer si esa persona es confiable, trabajadora, inteligente, etc. Esta interpretación, propensa a errores, deriva de la capacidad innata de los seres humanas de encontrar estas señales e interpretarlas. Esta capacidad es motivo de estudio, con un especial interés en desarrollar métodos que tengan la habilidad de calcular de manera automática estas señales o atributos asociados a la cara. Así, el interés por la estimación de atributos faciales ha crecido rápidamente en los últimos años por las diversas aplicaciones en que estos métodos pueden ser utilizados: marketing dirigido, sistemas de seguridad, interacción hombre-máquina, etc. Sin embargo, éstos están lejos de ser perfectos y robustos en cualquier dominio de problemas. La principal dificultad encontrada es causada por la alta variabilidad intra-clase debida a los cambios en la condición de la imagen: cambios de iluminación, oclusiones, expresiones faciales, edad, género, etnia, etc.; encontradas frecuentemente en imágenes adquiridas en entornos no controlados. Este de trabajo de investigación estudia técnicas de análisis de imágenes para estimar atributos faciales como el género, la edad y la postura, empleando métodos lineales y explotando las dependencias estadísticas entre estos atributos. Adicionalmente, nuestra propuesta se centrará en la construcción de estimadores que tengan una fuerte relación entre rendimiento y coste computacional. Con respecto a éste último punto, estudiamos un conjunto de estrategias para la clasificación de género y las comparamos con una propuesta basada en un clasificador Bayesiano y una adecuada extracción de características. Analizamos en profundidad el motivo de porqué las técnicas lineales no han logrado resultados competitivos hasta la fecha y mostramos cómo obtener rendimientos similares a las mejores técnicas no-lineales. Se propone un segundo algoritmo para la estimación de edad, basado en un regresor K-NN y una adecuada selección de características tal como se propuso para la clasificación de género. A partir de los experimentos desarrollados, observamos que el rendimiento de los clasificadores se reduce significativamente si los ´estos han sido entrenados y probados sobre diferentes bases de datos. Hemos encontrado que una de las causas es la existencia de dependencias entre atributos faciales que no han sido consideradas en la construcción de los clasificadores. Nuestro resultados demuestran que la variabilidad intra-clase puede ser reducida cuando se consideran las dependencias estadísticas entre los atributos faciales de el género, la edad y la pose; mejorando el rendimiento de nuestros clasificadores de atributos faciales con un coste computacional pequeño. Abstract Surely the human face provides much more information than we think. The face provides without our consent nonverbal cues from facial interactions that reveal our emotional state, cognitive activity, personality and disease. Recent studies [OFT14, TODMS15] show that many of our social and interpersonal decisions derive from a previous facial analysis that allows us to establish whether that person is trustworthy, hardworking, intelligent, etc. This error-prone interpretation derives from the innate ability of human beings to find and interpret these signals. This capability is being studied, with a special interest in developing methods that have the ability to automatically calculate these signs or attributes associated with the face. Thus, the interest in the estimation of facial attributes has grown rapidly in recent years by the various applications in which these methods can be used: targeted marketing, security systems, human-computer interaction, etc. However, these are far from being perfect and robust in any domain of problems. The main difficulty encountered is caused by the high intra-class variability due to changes in the condition of the image: lighting changes, occlusions, facial expressions, age, gender, ethnicity, etc.; often found in images acquired in uncontrolled environments. This research work studies image analysis techniques to estimate facial attributes such as gender, age and pose, using linear methods, and exploiting the statistical dependencies between these attributes. In addition, our proposal will focus on the construction of classifiers that have a good balance between performance and computational cost. We studied a set of strategies for gender classification and we compare them with a proposal based on a Bayesian classifier and a suitable feature extraction based on Linear Discriminant Analysis. We study in depth why linear techniques have failed to provide competitive results to date and show how to obtain similar performances to the best non-linear techniques. A second algorithm is proposed for estimating age, which is based on a K-NN regressor and proper selection of features such as those proposed for the classification of gender. From our experiments we note that performance estimates are significantly reduced if they have been trained and tested on different databases. We have found that one of the causes is the existence of dependencies between facial features that have not been considered in the construction of classifiers. Our results demonstrate that intra-class variability can be reduced when considering the statistical dependencies between facial attributes gender, age and pose, thus improving the performance of our classifiers with a reduced computational cost.

Detection of Biological CO2 and 1,3-Pentadiene Using Non-refrigerated Low-Cost MWIR Detectors

The early detection of spoiling metabolic products in contaminated food is a very important tool to control quality. Some volatile compounds produce unpleasant odours at very low concentrations, making their early detection very challenging. This is the case of 1,3-pentadiene produced by microorganisms through decarboxylation of the preservative sorbate. In this work, we have developed a methodology to use the data produced by a low-cost, compact MWIR (Mid-Wave IR) spectrometry device without moving parts, which is based on a linear array of 128 elements of VPD PbSe coupled to a linear variable filter (LVF) working in the spectral range between 3 and 4.6 ?m. This device is able to analyze food headspace gases through dedicated sample presentation setup. This methodology enables the detection of CO2 and the volatile compound 1,3-pentadiene, as compared to synthetic patrons. Data analysis is based on an automated multidimensional dynamic processing of the MWIR spectra. Principal component and discriminant analysis allow segregating between four yeast strains including producers and no producers. The segregation power is accounted as a measure of the discrimination quality.

Geoquímica multielementar de sedimentos de corrente no Estado de São Paulo: abordagem através da análise estatística multivariada

Este trabalho apresenta resultados geoquímicos multielementares de sedimentos de corrente no estado de São Paulo, obtidos através do projeto institucional do Serviço Geológico do Brasil denominado \"Levantamento Geoquímico de Baixa Densidade no Brasil\". Dados analíticos de 1422 amostras de sedimento de corrente obtidos por ICP-MS (Inductively Coupled Plasma Mass Spectrometry), para 32 elementos químicos (Al, Ba, Be, Ca, Ce, Co, Cr, Cs, Cu, Fe, Ga, Hf, K, La, Mg, Mn, Mo, Nb, Ni, P, Pb, Rb, Sc, Sn, Sr, Th, Ti, U, V, Y, Zn e Zr), foram processadas e abordadas através da análise estatística uni e multivariada. Os resultados do tratamento dos dados através de técnicas estatísticas univariadas forneceram os valores de background geoquímico (teor de fundo) dos 32 elementos para todo estado de São Paulo. A análise georreferenciada das distribuições geoquímicas unielementares evidenciaram a compartimentação geológica da área. As duas principais províncias geológicas do estado de São Paulo, Bacia do Paraná e Complexo Cristalino, se destacam claramente na maioria das distribuições geoquímicas. Unidades geológicas de maior expressão, como a Formação Serra Geral e o Grupo Bauru também foram claramente destacadas. Outras feições geoquímicas indicaram possíveis áreas contaminadas e unidades geológicas não cartografadas. Os resultados da aplicação de métodos estatísticos multivariados aos dados geoquímicos com 24 variáveis (Al, Ba, Ce, Co, Cr, Cs, Cu, Fe, Ga, La, Mn, Nb, Ni, Pb, Rb, Sc, Sr, Th, Ti, U, V, Y, Zn e Zr) permitiram definir as principais assinaturas e associações geoquímicas existentes em todo estado de São Paulo e correlacioná-las aos principais domínios litológicos. A análise de agrupamentos em modo Q forneceu oito grupos de amostras geoquimicamente correlacionáveis, que georreferenciadas reproduziram os principais compartimentos geológicos do estado: Complexo Cristalino, Grupos Itararé e Passa Dois, Formação Serra Geral e Grupos Bauru e Caiuá. A análise discriminante multigrupos comprovou, estatisticamente, a classificação dos grupos formados pela análise de agrupamentos e forneceu as principais variáveis discriminantes: Fe, Co, Sc, V e Cu. A análise de componentes principais, abordada em conjunto com a análise fatorial pelo método de rotação varimax, forneceram os principais fatores multivariados e suas respectivas associações elementares. O georreferenciamento dos valores de escores fatoriais multivariados delimitaram as áreas onde as associações elementares ocorrem e forneceram mapas multivariados para todo o estado. Por fim, conclui-se que os métodos estatísticos aplicados são indispensáveis no tratamento, apresentação e interpretação de dados geoquímicos. Ademais, com base em uma visão integrada dos resultados obtidos, este trabalho recomenda: (1) a execução dos levantamentos geoquímicos de baixa densidade em todo país em caráter de prioridade, pois são altamente eficazes na definição de backgrounds regionais e delimitação de províncias geoquímicas com interesse metalogenético e ambiental; (2) a execução do mapeamento geológico contínuo em escala adequada (maiores que 1:100.000) em áreas que apontam para possíveis existências de unidades não cartografadas nos mapas geológicos atuais.

Variables sociodemográficas, médicas y psicológicas relacionadas con el comportamiento de fumar y con los intentos de dejar de fumar en una muestra comunitaria

Se estudia la relación entre variables sociodemográficas, médicas y psicológicas y el comportamiento de fumar y los intentos de dejar de fumar. La muestra (n=291) se ha extraído al azar de una población comunitaria rural de 4300 habitantes. Todas las variables se han medido con un único cuestionario, a través de entrevista personal domiciliaria. Mediante análisis discriminantes las variables sexo, consumo de bebidas alcohólicas y el uso de medicamentos son las que más explican estadísticamente el comportamiento de fumar. Sorprendentemente, sólo una variable, haber visitado al médico en los últimos 12 meses, se asoció, bivariadamente, con los intentos de dejar de fumar, y no se procedía, lógicamente, con el análisis multivariante. Por último, se discuten los hallazgos a la luz de la literatura internacional y nacional.

Morphological classification of microtidal sand and gravel beaches

A new classification of microtidal sand and gravel beaches with very different morphologies is presented below. In 557 studied transects, 14 variables were used. Among the variables to be emphasized is the depth of the Posidonia oceanica. The classification was performed for 9 types of beaches: Type 1: Sand and gravel beaches, Type 2: Sand and gravel separated beaches, Type 3: Gravel and sand beaches, Type 4: Gravel and sand separated beaches, Type 5: Pure gravel beaches, Type 6: Open sand beaches, Type 7: Supported sand beaches, Type 8: Bisupported sand beaches and Type 9: Enclosed beaches. For the classification, several tools were used: discriminant analysis, neural networks and Support Vector Machines (SVM), the results were then compared. As there is no theory for deciding which is the most convenient neural network architecture to deal with a particular data set, an experimental study was performed with different numbers of neuron in the hidden layer. Finally, an architecture with 30 neurons was chosen. Different kernels were employed for SVM (Linear, Polynomial, Radial basis function and Sigmoid). The results obtained for the discriminant analysis were not as good as those obtained for the other two methods (ANN and SVM) which showed similar success.

The SAAS-R: A New Instrument to Assess the School Attitudes of Students with High and Low Academic Achievement in Spain

We examined the psychometric properties of the School Attitude Assessment Survey–Revised in a Spanish population (n = 1,398). Confirmatory factor analysis procedures supported the instrument’s five-factor structure. The results of discriminant analysis demonstrated the predictive power of the School Attitude Assessment Survey–Revised scales as regards academic performance. Implications for education and assessment are discussed.

(Table 1) Summary statistics of taxa in samples of ODP Hole 181-1123B

Planktonic foraminifera are used to identify late Pliocene-Quaternary near surface water masses on the northeastern flank of Chatham Rise by comparison with faunas in core-tops east of New Zealand. In an overview study, distance measures, ordinations, and discriminant analysis are applied to 32 faunas from Site 1123B to identify similar faunas among 35 core-tops between 35 and 61°S east of New Zealand. Many Site 1123B faunas in the 2.72 myr interval sampled compare with those in core-tops on the northern side of Chatham Rise from a similar latitude, and are identified as transitional zone assemblages now associated with the subtropical gyre. This result is consistent with studies of late Quaternary planktonic foraminifera from this region and suggests that, typically, the Subtropical Front was locked to Chatham Rise through glacial and interglacial periods, at least back to the late Pliocene. However, a fauna at ca. 1.17 Ma compares with subpolar assemblages in core-tops between 44 and 48°S and identifies cooler surface water. Expectedly, closer sampling may reveal additional periods when southern water moved over the northeastern flank of Chatham Rise. Although the dominance of Globorotalia inflata, a species typical of the southern margin of subtropical gyres, is a principal feature of Site 1123B faunas, in a minority it is replaced as the most abundant species by dextral populations of Neogloboquadrina pachyderma, particularly about the time of the middle Pleistocene transition. Close analogues of these variant transitional assemblages are not present in core-tops about Chatham Rise but sediment trap and coretop data from other regions suggest that they identify high fertility in the mixed layer associated with upwelling or mixing of water masses. The proportion of sinistrally coiled Neogloboquadrina pachyderma rises to ca. 0.6 between ca. 2.45 and 2.57 Ma, soon after the intensification of Northern Hemisphere glaciation. Although the coiling data indicate subantarctic near surface water, the species remains rare. As the faunas retain their transitional zone character, only minor entrainment of subantarctic water may have occurred.