Si3N4 single-crystal nanowires grown from silicon micro- and nanoparticles near the threshold of passive oxidation

A simple and most promising oxide-assisted catalyst-free method is used to prepare silicon nitride nanowires that give rise to high yield in a short time. After a brief analysis of the state of the art, we reveal the crucial role played by the oxygen partial pressure: when oxygen partial pressure is slightly below the threshold of passive oxidation, a high yield inhibiting the formation of any silica layer covering the nanowires occurs and thanks to the synthesis temperature one can control nanowire dimensions

Reduction of Concrete Deterioration by Ettringite Using Crystal Growth Inhibition Techniques: Part II Field Evaluation of Inhibitor Effectiveness, TR-469, 2004

The effects of diethylenetriaminpenta(methylenephosphonic acid) (DTPMP), a phosphonate inhibitor, on the growth of delayed ettringite have been evaluated using concrete in highway US 20 near Williams, Iowa, and the cores of six highways subject to moderate (built in 1992) or minor (built in 1997) deterioration. Application of 0.01 and 0.1 vol. % DTPMP to cores was made on a weekly or monthly basis for one year under controlled laboratory-based freeze-thaw and wet-dry conditions over a temperature range of -15 degrees to 58 degrees C to mimic extremes in Iowa roadway conditions. The same concentrations of phosphonate were also applied to cores left outside (roof of Science I at Iowa State University) over the same period of time. Nineteen applications of 0.1 vol. % DTPMP with added deicing salt solution (about 23 weight % NACL) were made to US 20 during the winters of 2003 and 2004. In untreated samples, air voids, pores, and occasional cracks are lined with acicular ettringite crystals (up to 50 micrometers in length) whereas air voids, pores, and cracks in concrete from the westbound lane of US 20 are devoid of ettringite up to a depth of about 0.5 mm from the surface of the concrete. Ettringite is also absent in zones up to 6 mm from the surface of concrete slabs placed on the roof of Science I and cores subject to laboratory-based freeze-thaw experiments. In these zones, the relatively high concentration of DTPMP caused it to behave as a chelator. Stunted ettringite crystals 5 to 25 micrometers in length, occasionally coated with porlandite, form on the margins of these zones indicating that in these areas DTPMP behaved as an inhibitor due to a reduction in the concentration of phosphonate. Analyses of mixes of ettringite and DTPMP using electrospray mass spectrometry suggests that the stunting of ettringite growth is caused by the adsorption of a Ca2+ ion and a water molecule to deprotonated DTPMP on the surface of the {0001} face of ettringite. It is anticipated that by using a DTPMP concentration of between 0.001 and 0.01 vol. % for the extended life of a highway (i.e. >20 years), deterioration caused by the expansive growth of ettringite will be markedly reduced.

Recent Observations of the Distribution and Status of Bluntnose Darters and Crystal Darters in Iowa

The distribution and status of Iowa's fishes were last extensively described in Iowa Fish and Fishing (Harlan et al. 1987). Since then, numerous fish collections have been made in Iowa's interior and bordering rivers and streams. Excluding non-native species, there have been three documented accounts of new fish species distributional records in Iowa since 1987. In this paper, I describe new collections of Crystal Darter (Crystallaria asprella) and Bluntnose Darter (Etheostoma chlorosomum) from the Mississippi River. The first documented specimen of C. asprella in Iowa was collected in Pool 11 of the Upper Mississippi River (UMR) in 1995. One specimen of E. chlorosomum was collected in Pool 13 of the UMR in 1998, and another was collected in 1999. The bluntnose darter had not been collected since 1975 and was generally thought to be extirpated in Iowa.

Crystal structures of two closely related but antigenically distinct HLA-A2/melanocyte-melanoma tumor-antigen peptide complexes.

We have determined high-resolution crystal structures of the complexes of HLA-A2 molecules with two modified immunodominant peptides from the melanoma tumor-associated protein Melan-A/Melanoma Ag recognized by T cells-1. The two peptides, a decamer and nonamer with overlapping sequences (ELAGIGILTV and ALGIGILTV), are modified in the second residue to increase their affinity for HLA-A2. The modified decamer is more immunogenic than the natural peptide and a candidate for peptide-based melanoma immunotherapy. The crystal structures at 1.8 and 2.15 A resolution define the differences in binding modes of the modified peptides, including different clusters of water molecules that appear to stabilize the peptide-HLA interaction. The structures suggest both how the wild-type peptides would bind and how three categories of cytotoxic T lymphocytes with differing fine specificity might recognize the two peptides.

Comparative study of upper lip frenectomy with the CO2 laser versus the Er, Cr: YSGG laser

Objectives: To compare upper lip frenulum reinsertion, bleeding, surgical time and surgical wound healing in frenectomies performed with the CO2 laser versus the Er, Cr:YSGG laser. Study design: A prospective study was carried out on 50 randomized pediatric patients who underwent rhomboidal resection of the upper lip frenulum with either the CO2 laser or the Er,Cr:YSGG laser. Twenty-five patients were assigned to each laser system. All patients were examined at 7, 14, 21 days and 4 months after the operation in order to assess the surgical wound healing. Results: Insertion of the frenulum, which was preoperatively located between the upper central incisors, migrated to the mucogingival junction as a result of using both laser systems in all patients. Only two patients required a single dose of 650 mg of paracetamol, one of either study group. CO2 laser registered improved intraoperative bleeding control results and shorter surgical times. On the other hand, the Er,Cr:YSGG laser achieved faster healing. Conclusions: Upper lip laser frenectomy is a simple technique that results in minimum or no postoperative swelling or pain, and which involves upper lip frenulum reinsertion at the mucogingival junction. The CO2 laser offers a bloodless field and shorter surgical times compared with the Er,Cr:YSGG laser. On the other hand, the Er,Cr:YSGG laser achieved faster wound healing.

Crystal size distribution of periclase in contact metamorphic dolomite marbles from the southern Adamello Massif, Italy

Crystal size distributions (CSD) of periclase in contact metamorphic dolomite marbles are presented for two profiles near the Cima Uzza summit in the southern Adamello Massif (Italy). The database was combined with geochemical and petrological information to deduce the controls on the periclase-forming reaction. The contact metamorphic dolomite marbles are exposed at the contact of mafic intrusive rocks and are partially surrounded by them. Brucite is retrograde and pseudomorphs spherical periclase crystals. Prograde periclase growth is the consequence of limited infiltration of water-rich fluid at T near 605C. Stable isotope data show depletion in (13)C and (18)O over a narrow region (40 cm) near the magmatic contact, whereas the periclase-forming reaction front extends up to 4 m from the contact. CSD analyses along the two profiles show that the median grain size of the periclase crystals does not change, but that there is a progressively greater distribution of grain sizes, including a greater proportion of larger grains, with increasing distance from the contact. A qualitative model, based on the textural and geochemical data, attributes these variations in grain size to changing reaction affinities along a kinetically dispersed infiltration front. This study highlights the need to invoke disequilibrium processes for metamorphic mineral growth and expands the use of CSDs to systems of mineral formation driven by fluid infiltration.

A comparison of the imaging characteristics of the new Kodak Hyper Speed G film with the current T-MAT G/RA film and the CR 9000 system.

Three standard radiation qualities (RQA 3, RQA 5 and RQA 9) and two screens, Kodak Lanex Regular and Insight Skeletal, were used to compare the imaging performance and dose requirements of the new Kodak Hyper Speed G and the current Kodak T-MAT G/RA medical x-ray films. The noise equivalent quanta (NEQ) and detective quantum efficiencies (DQE) of the four screen-film combinations were measured at three gross optical densities and compared with the characteristics for the Kodak CR 9000 system with GP (general purpose) and HR (high resolution) phosphor plates. The new Hyper Speed G film has double the intrinsic sensitivity of the T-MAT G/RA film and a higher contrast in the high optical density range for comparable exposure latitude. By providing both high sensitivity and high spatial resolution, the new film significantly improves the compromise between dose and image quality. As expected, the new film has a higher noise level and a lower signal-to-noise ratio than the standard film, although in the high frequency range this is compensated for by a better resolution, giving better DQE results--especially at high optical density. Both screen-film systems outperform the phosphor plates in terms of MTF and DQE for standard imaging conditions (Regular screen at RQA 5 and RQA 9 beam qualities). At low energy (RQA 3), the CR system has a comparable low-frequency DQE to screen-film systems when used with a fine screen at low and middle optical densities, and a superior low-frequency DQE at high optical density.

Mechanisms of garnet growth in eclogites of the Zermatt-Saas Fee unit, Western Alps

THESIS ABSTRACT Garnets are one of the key metamorphic minerals used to study peak metamorphic conditions or crystallization ages. Equilibrium is typically assumed between the garnet and the matrix. This thesis attempts to understand garnet growth in the Zermatt-Saas Fee (ZSF) eclogites, and discusses consequences for Sm/Nd and Lu/Hf dating and the equilibrium assumption. All studied garnets from the ZSF eclogites are strongly zoned in Mn, Fe, Mg, and Ca. Methods based on chemical zoning patterns and on 3D spatial statistics indicate different growth mechanisms depending on the sample studied. Garnets from the Pfulwe area are grown in a system where surface kinetics likely dominated over intergranular diffusion kinetics. Garnets fram two other localities, Nuarsax and Lago di Cignana, seem to have grown in a system where intergranular diffusion kinetics were dominating over surface kinetics, at least during initial growth. Garnets reveal strong prograde REE+Y zoning. They contain narrow central peaks for Lu + Yb + Tm ± Er and at least one additional small peak towards the rim. The REE Sm + Eu + Gd + Tb ± Dy are depleted in the cores but show one prominent peak close to the rim. It is shown that these patterns cam be explained using a transient matrix diffusion model where REE uptake is limited by diffusion in the matrix surrounding the porphyroblast. The secondary peaks in the garnet profiles are interpreted to reflect thermally activated diffusion due to a temperature increase during prograde metamorphism. The model predicts anomalously low 176Lu/177Hf and 147Sm/144Nd ratios in garnets where growth rates are fast compared to diffusion of the REE, which decreases garnet isochron precisions. The sharp Lu zoning was further used to constrain maximum Lu volume diffusion rates in garnet. The modeled minimum pre-exponential diffusion coefficient which fits the measured central peak is in the order of Do = 5.7* 106 m2/s, taking an activation energy of 270 kJ/mol. The latter was chosen in agreement with experimentally determined values. This can be used to estimate a minimum closure temperature of around 630°C for the ZSF zone. Zoning of REE was combined with published Lu/Hf and Sm/Nd age information to redefine the prograde crystallization interval for Lago di Cignana UHP eclogites. Modeling revealed that a prograde growth interval in the order of 25 m.y. is needed to produce the measured spread in ages. RÉSUMÉ Le grenat est un minéral métamorphique clé pour déterminer les conditions du pic de métamorphisme ainsi que l'âge de cristallisation. L'équilibre entre le grenat et la matrice est requis. Cette étude a pour but de comprendre la croissance du grenat dans les éclogites de la zone de Zermatt-Saas Fee (ZSF) et d'examiner quelques conséquences sur les datations Sm/Nd et Lu/Hf. Tous les grenats des éclogites de ZSF étudiés sont fortement zonés en Mn, Fe, Mg et partiellement en Ca. Les différentes méthodes basées sur le modèle de zonation chimique ainsi que sur les statistiques de répartition spatiale en 3D indiquent un mécanisme de croissance différent en fonction de la localité d'échantillonnage. Les grenats provenant de la zone de Pfulwe ont probablement crû dans un système principalement dominé par la cinétique de surface au détriment de 1a cinétique de diffusion intergranulaire. Les grenats provenant de deux autres localités, Nuarsax et Lago di Cignana, semblent avoir cristallisé dans un système dominé par la diffusion intergranulaire, au moins durant les premiers stades de croissance. Les grenats montrent une forte zonation prograde en Terres Rares (REE) ainsi qu'en Y. Les profils présentent au coeur un pic étroit en Lu + Yb+ Tm ± Er et au moins un petit pic supplémentaire vers le bord. Les coeurs des grenats sont appauvris en Sm + Eu + Gd + Tb ± Dy, mais les bords sont marqués par un pic important de ces REE. Ces profils s'expliquent par un modèle de diffusion matricielle dans lequel l'apport en REE est limité par la diffusion dans la matrice environnant les porphyroblastes. Les pics secondaires en bordure de grain reflètent la diffusion activée par l'augmentation de la température lors du métamorphisme prograde. Ce modèle prédit des rapports 176Lu/177Hf et 147Sm/144Nd anormalement bas lorsque les taux de croissance sont plus rapides que la diffusion des REE, ce qui diminue la précision des isochrones impliquant le grenat. La zonation nette en Lu a permis de contraindre le maximum de diffusion volumique par une approche numérique. Le coefficient de diffusion minimum modélisé en adéquation avec les pics mesurés est de l'ordre de Do = 5.7*10-6 m2/s, en prenant une énergie d'activation ~270 kJ/mol déterminée expérimentalement. Ainsi, la température de clôture minimale est estimée aux alentours de 630°C pour la zone ZSF. Des nouvelles données de zonation de REE sont combinées aux âges obtenus avec les rapports Lu/Hf et Sm/Nd qui redéfissent l'intervalle de cristallisation prograde pour les éclogites UHP de Lago di Cignana. La modélisation permet d'attribuer au minimum un intervalle de croissance prograde de 25 Ma afin d'obtenir les âges préalablement mesurés. RESUME GRAND PUBLIC L'un des principaux buts du pétrologue .métamorphique est d'extraire des roches les informations sur l'évolution temporelle, thermique et barométrique qu'elles ont subi au cours de la formation d'une chaîne de montagne. Le grenat est l'un des minéraux clés dans une grande variété de roches métamorphiques. Il a fait l'objet de nombreuses études dans des terrains d'origines variées ou lors d'études expérimentales afin de comprendre ses domaines de stabilité, ses réactions et sa coexistence avec d'autres minéraux. Cela fait du grenat l'un des minéraux les plus attractifs pour la datation des roches. Cependant, lorsqu'on l'utilise pour la datation et/ou pour la géothermobarométrie, on suppose toujours que le grenat croît en équilibre avec les phases coexistantes de la matrice. Pourtant, la croissance d'un minéral est en général liée au processus de déséquilibre. Cette étude a pour but de comprendre comment croît le grenat dans les éclogites de Zermatt - Saas Fee et donc d'évaluer le degré de déséquilibre. Il s'agit aussi d'expliquer les différences d'âges obtenues grâce aux grenats dans les différentes localités de l'unité de Zermatt-Saas Fee. La principale question posée lors de l'étude des mécanismes de croissance du grenat est: Parmi les processus en jeu lors de la croissance du grenat (dissolution des anciens minéraux, transport des éléments vers le nouveau grenat, précipitation d'une nouvelle couche en surface du minéral), lequel est le plus lent et ainsi détermine le degré de déséquilibre? En effet, les grenats d'une des localités (Pfulwe) indiquent que le phénomène d'adhérence en surface est le plus lent, contrairement aux grenats des autres localités (Lago di Cignana, Nuarsax) dans lesquels ce sont les processus de transport qui sont les plus lents. Cela montre que les processus dominants sont variables, même dans des roches similaires de la même unité tectonique. Ceci implique que les processus doivent être déterminés individuellement pour chaque roche afin d'évaluer le degré de déséquilibre du grenat dans la roche. Tous les grenats analysés présentent au coeur une forte concentration de Terres Rares: Lu + Yb + Tm ± Er qui décroît vers le bord du grain. Inversement, les Terres Rares Sm + Eu + Gd + Tb ± Dy sont appauvries au coeur et se concentrent en bordure du grain. La modélisation révèle que ces profils sont-dus à des cinétiques lentes de transport des Terres Rares. De plus, les modèles prédisent des concentrations basses en éléments radiogéniques pères dans certaines roches, ce qui influence fortement sur la précision des âges obtenus par la méthode d'isochrone. Ceci signifie que les roches les plus adaptées pour les datations ne doivent contenir ni beaucoup de grenat ni de très gros cristaux, car dans ce cas, la compétition des éléments entre les cristaux limite à de faibles concentrations la quantité d'éléments pères dans chaque cristal.

Nd:YAG Laser Welding of 5083 Aluminium Alloy using Filler Wire

High reflectivity and high thermal conductivity, high vapour pressure of alloyingelements as well as low liquid surface tension and low ionisation potential, make laser welding of aluminium and its alloys a demanding task.Problems that occur during welding are mainly process instabilities of the keyhole and the melt pool, increased plasma formation above the melt pool and loss of alloying elements. These problems lead to unwanted metallurgical defects like hot cracks and porosity in the weld bead andother problems concerning the shape and appearance of the weld bead. In order to minimise the defects and improve the weld quality, the process and beam parameters need to be carefully adjusted along with a consideration concerning the use of filler wire for the welding process. In this work the welding of 3,0 mm thick grade 5083 aluminium alloy plates using a 3,0 kW Nd:YAG laser with grade 5183 filler wire addition is investigated. The plates were welded as butt joints with air gap sizes 0,5 mm, 0,7mm and 1,0 mm. The analysis of the weld beads obtained from the weldedsamples showed that the least imperfections were produced with 0,7 mm air gaps at moderate welding speeds. The analysis also covered the calculation of the melting efficiency and the study of the shape of the weld bead. The melting efficiency was on average around 20 % for the melting process of the welded plates. The weld beads showed the characteristic V-shape of a laser weld and retained this shape during the whole series of experiments.

Up-conversion effect of Er- and Yb-doped ZnO thin films

Visible up-conversion in ZnO:Er and ZnO:Er:Yb thin films deposited by RF magnetron sputtering under different O2-rich atmospheres has been studied. Conventional photoluminescence (325 nm laser source) and up-conversion (980 nm laser source) have been performed in the films before and after an annealing process at 800 °C. The resulting spectra demonstrate that the thermal treatment, either during or post-deposition, activates optically the Er3+ ions, being the latter process much more efficient. Moreover, the atmosphere during deposition was also found to be an important parameter, as the deposition under O2 flow increases the optical activity of Er+3 ions. In addition, the inclusion of Yb3+ ions into the films has shown an enhancement of the visible up-conversion emission at 660 nm by a factor of 4, which could be associated to either a better energy transfer from the 2F5/2 Yb level to the 4I11/2 Er one, or to the prevention of having Er2O3 clustering in the films.

In vitro evaluation of the temperature increment at the external root surface after Er,Cr: YSGG laser irradiation of the root canal

Objectives: A study was made to determine the temperature increment at the dental root surface following Er,Cr:YSGG laser irradiation of the root canal. Design. Human canines and incisors previously instrumented to K file number ISO 30 were used. Irradiation was carried out with glass fiber endodontic tips measuring 200 μm in diameter and especially designed for insertion in the root canal. The teeth were irradiated at 1 and 2 W for 30 seconds, without water spraying or air, and applying a continuous circular movement (approximately 2 mm/sec.) in the apico-coronal direction. Results: At the 1 W power setting, the mean temperature increment was 3.84ºC versus 5.01ºC at 2 W. In all cases the difference in mean value obtained after irradiation versus the mean baseline temperature proved statistically significant (p< 0.05). Conclusions: Application of the Er,Cr:YSGG laser gives rise to a statistically significant temperature increment at the external root surface, though this increment is probably clinically irrelevant, since it would appear to damage the tissues (periodontal ligament and alveolar bone) in proximity to the treated tooth

Comprehensive Study of Crystal Growth from Solution

Crystal growth is an essential phase in crystallization kinetics. The rate of crystal growth provides significant information for the design and control of crystallization processes; nevertheless, obtaining accurate growth rate data is still challenging due to a number of factors that prevail in crystal growth. In industrial crystallization, crystals are generally grown from multi-componentand multi-particle solutions under complicated hydrodynamic conditions; thus, it is crucial to increase the general understanding of the growth kinetics in these systems. The aim of this work is to develop a model of the crystal growth rate from solution. An extensive literature review of crystal growth focuses on themodelling of growth kinetics and thermodynamics, and new measuring techniques that have been introduced in the field of crystallization. The growth of a singlecrystal is investigated in binary and ternary systems. The binary system consists of potassium dihydrogen phosphate (KDP, crystallizing solute) and water (solvent), and the ternary system includes KDP, water and an organic admixture. The studied admixtures, urea, ethanol and 1-propanol, are employed at relatively highconcentrations (of up to 5.0 molal). The influence of the admixtures on the solution thermodynamics is studied using the Pitzer activity coefficient model. Theprediction method of the ternary solubility in the studied systems is introduced and verified. The growth rate of the KDP (101) face in the studied systems aremeasured in the growth cell as a function of supersaturation, the admixture concentration, the solution velocity over a crystal and temperature. In addition, the surface morphology of the KDP (101) face is studied using ex situ atomic force microscopy (AFM). The crystal growth rate in the ternary systems is modelled on the basis of the two-step growth model that contains the Maxwell-Stefan (MS) equations and a surface-reaction model. This model is used together with measuredcrystal growth rate data to develop a new method for the evaluation of the model parameters. The validation of the model is justified with experiments. The crystal growth rate in an imperfectly mixed suspension crystallizer is investigatedusing computational fluid dynamics (CFD). A solid-liquid suspension flow that includes multi-sized particles is described by the multi-fluid model as well as by a standard k-epsilon turbulence model and an interface momentum transfer model. The local crystal growth rate is determined from calculated flow information in a diffusion-controlled crystal growth regime. The calculated results are evaluated experimentally.

Aplicaciones del láser Nd:YAG en odontologia

El láser de Nd:YAG está compuesto por un granate de itrio y aluminio, contaminado por neodimio. Emite a una longitud de onda de 1064 nm, en el infrarrojo cercano. A diferencia de otros láseres, el láser de Nd:YAG, puede transmitirse a través de fibra óptica, lo cual permite una fácil aplicación de este tipo de energía en espacios anatómicos bucodentarios de difícil acceso. Este hecho, asociado al potente efecto bactericida que produce esta longitud de onda, lo convierten en una herramienta ideal en los tratamientos endodóncicos y periodontales, en los que puede mejorar los resultados obtenidos con las técnicas convencionales. También se utiliza en ciertos tratamientos de Cirugía Bucal, principalmente para las exéresis de lesiones de tejidos blandos.