Immersion enthalpy variation of surface-modified mineral activated carbon in lead (II) aqueous solution adsorption: the relation between immersion enthalpy and adsorption capacity

An activated carbon was obtained by chemical activation with phosphoric acid, CM, from a mineral carbon. Afterwards, the carbon was modified with 2 and 5 molL-1, CMox2 and CMox5 nitric acid solutions to increase the surface acid group contents. Immersion enthalpy at pH 4 values and Pb2+ adsorption isotherms were determined by immersing activated carbons in aqueous solution. The surface area values of the adsorbents and total pore volume were approximately 560 m².g-1 and 0.36 cm³g-1, respectively. As regards chemical characteristics, activated carbons had higher acid sites content, 0.92-2.42 meq g-1, than basic sites, 0.63-0.12 meq g-1. pH values were between 7.4 and 4.5 at the point of zero charge, pH PZC. The adsorbed quantity of Pb2+ and the immersion enthalpy in solution of different pH values for CM activated carbon showed that the values are the highest for pH 4, 15.7 mgg-1 and 27.6 Jg-1 respectively. Pb2+ adsorption isotherms and immersion enthalpy were determined for modified activated carbons and the highest values were obtained for the activated carbon that showed the highest content of total acid sites on the surface.

Adsorption isotherm studies of Cd (II), Pb (II) and Zn (II) ions bioremediation from aqueous solution using unmodified and EDTA-modified maize cob

The need to clean-up heavy metal contaminated environment can not be over emphasized. This paper describes the adsorption isotherm studies of Cd (II), Pb (II) and Zn (II) ions from aqueous solution using unmodified and EDTA-modified maize cob. Maize cob was found to be an excellent adsorbent for the removal of these metal ions. The amount of metal ions adsorbed increased as the initial concentration increased. Also, EDTA - modification enhanced the adsorption capacity of maize cob probably due to the chelating ability of EDTA. Among the three adsorption isotherm tested, Dubinin-Radushkevich gave the best fit with R² value ranging from 0.9539 to 0.9973 and an average value of 0.9819. This is followed by Freundlich isotherm (Ave. 0.9783) and then the Langmuir isotherm (Ave. 0.7637). The sorption process was found to be a physiosorption process as seen from the apparent energy of adsorption which ranged from 2.05KJ\mol to 4.56KJ\mol. Therefore, this study demonstrates that maize cob which is an environmental pollutant could be used to adsorb heavy metals and achieve cleanliness thereby abating environmental nuisance caused by the maize cob.

A fluorescence probe study of gemini surfactants in aqueous solution: a comparison between n-2-n and n-6-n series of the alkanediyl-a,w-bis (dimethylalkylammonium bromides)

Two series of alkanediyl-a,w-bis (dimethylalkylammonium bromide (n-2-n and n-6-n; n=8, 10,12, and 16) have been synthesized and their micelles properties studied in aqueous solution using pyrene, pyrenecarboxaldehyde (PCA) and 1,8 anilinonaphtalene sulfonic acid sodium salt (ANS) as fluorescent probes. The micelles from these surfactants have been characterized on the basis of the information provided by micelle-solubilized fluorescent probes. The obtained results indicated that the surfactant concentration at which a marked decrease in l max parameter of pyrenecarboxaldehyde (PCA) occurs corresponds to the CMC determined by conductimetric measurements. Changes in the emission spectra of ANS and PCA observed in the submicellar range for both surfactants series (n-2-n and n-6-n) were interpreted as formation of pre-aggregates. It was found that the dimeric surfactants with long spacer (s= 6) form more hydrated aggregates when compared with those formed by the n-2-n and CnTAB surfactants series. This was attributed to a more difficult packing of n-6-n surfactant molecules to form micelles.

The concept of solution: Industry’s insights compared to theoretical views

Many manufacturing companies have started to offer complete solutions to their customers’ unique needs due to toughening competition and customer demand. Discourse on this kind of solution business is still developing, hence, there is not an established definition for the concept of solution. The aim of the study is to profoundly identify the concept of solution and to understand how the industry’s current views differ from the theoretical concepts. The describing dimensions are identified from selected 13 theoretical notions, and from responses, that the employees of five different companies have given. The 32 interview transcripts are analyzed with thematic analysis and qualitative content analysis. According to the findings, the concept of solution is characterized by integration, customization, risk-sharing, value co-creation, long-term orientation, and desired outcomes. The industry’s insights differ in terms of them all. The results illustrate, that a solution is a bundle, and the whole solution is customized on some level for a client. A solution supplier needs to be customer-focused, in which value co-creation is only a part. The solution solves the customer’s problem, and improves both the customer’s, and the supplier’s business. Neither long-term focus nor risks-sharing were directly employed to characterize the concept of solution. Differences are mainly due to the different approaches to the definitions and inexperience of the companies.

Evaluating the Advantages of Implementing a CRM solution

CRM-järjestelmän avulla pyritään yleisesti tehostamaan liiketoimintaprosesseja. Yrityksestä, kuin myös toimialasta riippuen hyödyt sekä tavoitteet vaihtelevat jonkin verran. Usein CRM-järjestelmän avulla saavutettavien hyötyjen mittaaminen ja arviointi organisaatiossa koetaan hankalaksi ja täten todellinen hyötyjen arviointi jää suppeaksi. Tämän tutkimuksen tavoitteena oli kartoittaa etuja, joita CRM-järjestelmän käyttöönotto on todellisuudessa tuonut yrityksille. Tutkimus kulminoituu laskentamalliin, jonka avulla CRM käytön hyödyt konvertoidaan konkreettiseksi rahasummaksi. Tutkimuksessa pyritään vastaamaan seuraaviin tutkimuskysymyksiin: 1. Kun yritys suunnitteli CRM-sovelluksen käyttöönottoa, mitkä olivat järjestelmälle asetetut tavoitteet? 2. Onko yritys saavuttanut CRM-järjestelmälle asetetut tavoitteet? 3. Onko yritys saavuttanut odottamattomia hyötyjä CRM-järjestelmän käytön avulla? 4. Mitkä ovat CRM-järjestelmän tärkeimmät kehityskohteet käyttökokemusten perusteella? Tutkimus perustuu CRM-kirjallisuuden avulla luotuun teoriaviitekehykseen. Teoriaviitekehyksen pohjalta luotiin ideaalimalli ja mallin pohjalta web-survey -kysely. Kyselyn tulosten perusteella toteutettiin haastatteluja, joilla pyrittiin saamaan tutkimustuloksiin syvyyttä.

A quasi-materialist, quasi-dualist solution to the mind-body problem

If the mental can affect, or be affected by, the physical, then the mental must itself be physical. Otherwise the physical world would not be explanatorily closed. But it is closed. There are reasons to hold that materialism (in both its reductive and non-reductive varieties) is false. So how are we to explain the apparent responsiveness of the physical to the mental and vice versa? The only possible solution seems to be this: physical objects are really projections or isomorphs of objects whose essential properties are mental. (A slightly less accurate way of putting this would be to say: the constitutive - i.e. the non-structural and non-phenomenal - properties of physical objects are mental, i.e. are such as we are used to encountering only in "introspection".) The chair, qua thing that I can know through sense perception, and through hypotheses based strictly thereupon, is a kind of shadow of an object that is exactly like it, except that this other objects essential properties are mental. This line of thought, though radically counterintuitive, explains the apparent responsiveness of the mental to the physical, and vice versa, without being open to any of the criticisms to which materialism, dualistic interaction ism, and epiphenomenalism are open.

Vaihtosuuntaajan reaaliaikainen lämpömalli

Vaihtosuuntaajan IGBT-moduulin liitosten lämpötiloja ei voida suoraan mitata, joten niiden arviointiin tarvitaan reaaliaikainen lämpömalli. Tässä työssä on tavoitteena kehittää tähän tarkoitukseen C-kielellä implementoitu ratkaisu, joka on riittävän tarkka ja samalla mahdollisimman laskennallisesti tehokas. Ohjelmallisen toteutuksen täytyy myös sopia erilaisille moduulityypeille ja sen on tarvittaessa otettava huomioon saman moduulin muiden sirujen lämmittävä vaikutus toisiinsa. Kirjallisuuskatsauksen perusteella valitaan olemassa olevista lämpömalleista käytännön toteutuksen pohjaksi lämpöimpedanssimatriisiin perustuva malli. Lämpöimpedanssimatriisista tehdään Simulink-ohjelmalla s-tason simulointimalli, jota käytetään referenssinä muun muassa implementoinnin tarkkuuden verifiointiin. Lämpömalli tarvitsee tiedon vaihtosuuntaajan häviöistä, joten työssä on selvitetty eri vaihtoehtoja häviölaskentaan. Lämpömallin kehittäminen s-tason mallista valmiiksi C-kieliseksi koodiksi on kuvattu tarkasti. Ensin s-tason malli diskretoidaan z-tasoon. Z-tason siirtofunktiot muutetaan puolestaan ensimmäisen kertaluvun differenssiyhtälöiksi. Työssä kehitetty monen aikatason lämpömalli saadaan jakamalla ensimmäisen kertaluvun differenssiyhtälöt eri aikatasoille suoritettavaksi sen mukaan, mikä niiden kuvaileman termin vaatima päivitysnopeus on. Tällainen toteutus voi parhaimmillaan kuluttaa alle viidesosan kellojaksoja verrattuna suoraviivaiseen yhden aikatason toteutukseen. Implementoinnin tarkkuus on hyvä. Implementoinnin vaatimia suoritusaikoja testattiin Texas Instrumentsin TMS320C6727- prosessorilla (300 MHz). Esimerkkimallin laskemisen määritettiin kuluttavan vaihtosuuntaajan toimiessa 5 kHz kytkentätaajuudella vain 0,4 % prosessorin kellojaksoista. Toteutuksen tarkkuus ja laskentakapasiteetin vähäinen vaatimus mahdollistavat lämpömallin käyttämisen lämpösuojaukseen ja lisäämisen osaksi muuta jo prosessorilla olemassa olevaa systeemiä.

General terms and rigidity: another solution to the trivialization problem

In this paper I am concerned with the problem of applying the notion of rigidity to general terms. In Naming and Necessity, Kripke has clearly suggested that we should include some general terms among the rigid ones, namely, those common nouns semantically correlated with natural substances, species and phenomena, in general, natural kinds -'water', 'tiger', 'heat'- and some adjectives -'red', 'hot', 'loud'. However, the notion of rigidity has been defined for singular terms; after all, the notion that Kripke has provided us with is the notion of a rigid designator. But general terms do not designate single individuals: rather, they apply to many of them. In sum, the original concept of rigidity cannot be straightforwardly applied to general terms: it has to be somehow redefined in order to make it cover them. As is known, two main positions have been put forward to accomplish that task: the identity of designation conception, according to which a rigid general term is one that designates the same property or kind in all possible worlds, and the essentialist conception, which conceives of a rigid general term as an essentialist one, namely, a term that expresses an essential property of an object. My purpose in the present paper is to defend a particular version of the identity of designation conception: on the proposed approach, a rigid general term will be one that expresses the same property in all possible worlds and names the property it expresses. In my opinion, the position can be established on the basis of an inference to the best explanation of our intuitive interpretation and evaluation, relative to counterfactual circumstances, of statements containing different kinds of general terms, which is strictly analogous to our intuitive interpretation and evaluation, relative to such circumstances, of statements containing different kinds of singular ones. I will argue that it is possible to offer a new solution to the trivialization problem that is thought to threaten all versions of the identity of designation conception of rigidity. Finally, I will also sketch a solution to the so-called 'over-generalization and under-generalization problems', both closely related to the above-mentioned one.

Imazapyr root exudation from eucalypt seedlings cultivated in nutritive solution

Imazapyr has been used in Brazilian eucalypt cultivation for the maintenance of clearings and coppicing control in areas undergoing stand reform. However, inquiries have been made as to the final fate of the molecule. Imazapyr root exudation in eucalypt plants was evaluated through a bioassay under greenhouse conditions, by applying different herbicide doses (0.000, 0.375, 0.750, 1.125, and 1.500 kg ha-1 a.i.) on Eucalyptus grandis seedlings derived from vegetative propagation, hydroponically cultivated in 2.500 ml vases. Forty-day-old seedlings of the same clone were used as bioindicators, transplanted to the vases two days after herbicide application. After a period of 13 days of coexistence, the sprayed plants were removed and discarded; ten days later, the visual symptoms of toxicity were evaluated and the total dry biomass (aerial part and roots) of the bioindicators were determined. The lowest herbicide dose (0.375 kg ha-1 a.i.) affected the total biomass and growth, being most evident in the aerial part, with larger I50 for root dry biomass. The E. grandis seedlings exuded imazapyr, and/or its metabolites, in concentrations capable of affecting the growth of plants of the same species.

Solution Business Model for Energy Efficiency

This study examined solution business models and how they could be applied into energy efficiency business. The target of this study was to find out, what a functional solution business model applied to energy efficiency improvement projects is like. The term “functionality” was used to refer not only to the economic viability but to environmental and legal aspects and also to the implement of Critical Success Factors (CSFs) and the ability to overcome the most important market barriers and risks. This thesis is based on a comprehensive literature study on solution business, business models and energy efficiency business. This literature review was used as a foundation to an energy efficiency solution business model scheme. The created scheme was tested in a case study which studied two different energy efficiency improvement projects, illustrated the functionality of the created business model and evaluated their potential as customer targets. Solution approach was found to be suitable for energy efficiency business. The most important characteristics of a good solution business model were identified to be the relationship between the supplier and customer, a proper network, knowledge on the customer’s process and supreme technological expertise. Thus the energy efficiency solution business was recognized to be particularly suitable for example for energy suppliers or technological equipment suppliers. Because the case study was not executed from a certain company’s point of view, the most important factors such as relationships and the availability of funding could not be evaluated. Although the energy efficiency business is recognized to be economically viable, the most important factors influencing the profitability and the success of energy efficiency solution business model were identified to be the proper risk management, the ability to overcome market barriers and the realization of CSFs.

Concentration of injetion solution and its effects on soil and on yield of fertirrigated banana cv. Terra Maranhão

The Fertigation is the combined application of water and nutrients to a crop. It can be adapted to all types of agricultural crops. The objective of this study was to evaluate the effect of urea concentration in irrigation water on electrical conductivity of the soil solution and saturation extract along the first cycle of banana cv. Terra Maranhão. The experiment followed a completely randomized design with six treatments and ten replications. Treatments regarded for using three urea concentrations (1.0; 2.5 and 4.0 g L-1) in irrigation water applied by two micro irrigation systems (microsprinkler and drip). Results showed that there was a linear elevation of electrical conductivity of saturation extract and soil solution with the increase on concentration of urea in the injection solution. Urea should be used under concentrations up to 2.5 g L-1 in irrigation water without causing increase on electric conductivity of soil solution and saturation extract, considering 1.1 dS m-1 as the tolerated value for the crop. Nitrate in the soil solution increased significantly with the increase of urea concentration in the injection solution. The maximum concentration of nitrate in the soil occurred for 4,0 g L-1 concentration of the injection solution.

Designing the transformation from a boiler supplier into a solution seller

Competition for customers in business-to-business markets is rough, and in order to survive a seller has to be able to deliver more value to its customers than its competitors. This thesis is done for the sales department of an energy technology company operating in business-to-business markets. The company is a relatively small in its field, and it aims to expand internationally and differ itself from its competitors by providing better service for its customers and selling solutions. This study aims to design the transformation from a product seller into a solution seller by defining what is a solution and how solutions are sold, and creating an action plan for sales. Data for the study is collected in ten theme interviews, and analyzed with thematic and content analysis. The action plan is constructed based both on the data and theory. According to the findings of the study, solution is defined as a specially designed unique combination of elements – such as products, services, knowledge, experience and thinking – that work with and complement each other, and bring value to a particular customer. Solution sales requires capabilities to anticipate; build relationships with customers; identify needs and define requirements; cocreate solutions by customizing and integrating elements; and provide postdeployment support. Vision for the change is to sell solution through sensing customers’ needs and responding to them, and the steps of the action plan are to (1) cascade customer-focus, (2) involve other departments in solution sales, (3) develop customer relationship management, and (4) involve the whole organization in solution business.