Caracterização mecânica de misturas betuminosas a aplicar em infra-estruturas de transportes

A maioria das infra-estruturas de transportes, nomeadamente os pavimentos rodoviários e aeroportuários, são constituídas por misturas betuminosas, o que permite um bom desempenho e uma adequada durabilidade, nas condições usuais de serviço. As misturas betuminosas são ainda amplamente utilizadas na construção de zonas de estacionamento de veículos, tendo-se verificado recentemente a sua aplicação também em infra-estruturas ferroviárias. Face à necessidade de melhorar o desempenho das vias-férreas, permitindo uma concepção mais durável de linhas de alta velocidade e uma redução dos custos da sua manutenção, tem-se vindo a desenvolver diversos estudos para promover a utilização de novos materiais, principalmente através da incorporação de misturas betuminosas. O presente trabalho tem como objectivo a caracterização do comportamento mecânico de misturas betuminosas a aplicar em infra-estruturas de transportes. Como metodologia para o estudo do comportamento mecânico das misturas betuminosas foram realizados em laboratório ensaios de cargas repetidas, nomeadamente, ensaios de flexão em quatro pontos para determinação da rigidez e da resistência à fadiga e ensaios de compressão triaxiais cíclicos para avaliação do comportamento à deformação permanente. A resistência à fadiga das misturas betuminosas em estudo foi avaliada através do ensaio de flexão em quatro pontos, com extensão controlada, e aplicação de um carregamento sinusoidal com diferentes frequências, de acordo com o procedimento de ensaio da norma europeia EN 12697-24 (2004 + A1: 2007). A resistência à deformação permanente das misturas betuminosas foi analisada através de ensaios de compressão triaxiais cíclicos, submetendo-as a uma tensão de confinamento estática pela aplicação parcial de vácuo e a uma pressão axial cíclica sob a forma rectangular, de acordo com a norma europeia EN 12697-25 (2004). O conhecimento destas propriedades mecânicas assume particular importância ao nível da formulação das misturas betuminosas, do dimensionamento de uma estrutura ou do estabelecimento de uma adequada solução para uma obra de reabilitação duma infra-estrutura de transportes. Para este estudo foi utilizado um modelo físico construído numa fossa no LNEC, com o propósito de serem testadas três substruturas ferroviárias não convencionais, utilizando sub-balastro betuminoso. A selecção das substruturas foi efectuada após uma análise de várias secções de estruturas já testadas e aplicadas noutros países, de forma a proporcionar comparações fiáveis entre elas. Os resultados obtidos mostraram que a mistura betuminosa AC20 base 50/70 (MB) aplicada na camada de sub-balastro é adequada para ser aplicada nas infra-estruturas de transportes pois apresenta um bom desempenho à fadiga e à deformação permanente. Através dos ensaios efectuados foi ainda possível entender a importante influência das características volumétricas, principalmente da porosidade para o bom comportamento da mistura betuminosa.

Design of a sea-level tsunami detection network for the Gulf of Cadiz

The devastating impact of the Sumatra tsunami of 26 December 2004, raised the question for scientists of how to forecast a tsunami threat. In 2005, the IOC-UNESCO XXIII assembly decided to implement a global tsunami warning system to cover the regions that were not yet protected, namely the Indian Ocean, the Caribbean and the North East Atlantic, the Mediterranean and connected seas (the NEAM region). Within NEAM, the Gulf of Cadiz is the more sensitive area, with an important record of devastating historical events. The objective of this paper is to present a preliminary design for a reliable tsunami detection network for the Gulf of Cadiz, based on a network of sea-level observatories. The tsunamigenic potential of this region has been revised in order to define the active tectonic structures. Tsunami hydrodynamic modeling and GIS technology have been used to identify the appropriate locations for the minimum number of sea-level stations. Results show that 3 tsunameters are required as the minimum number of stations necessary to assure an acceptable protection to the large coastal population in the Gulf of Cadiz. In addition, 29 tide gauge stations could be necessary to fully assess the effects of a tsunami along the affected coasts of Portugal, Spain and Morocco.

Response of a multi-domain continental margin to compression: Study from seismic reflection-refraction and numerical modelling in the Tagus Abyssal Plain

The effects of the Miocene through Present compression in the Tagus Abyssal Plain are mapped using the most up to date available to scientific community multi-channel seismic reflection and refraction data. Correlation of the rift basin fault pattern with the deep crustal structure is presented along seismic line IAM-5. Four structural domains were recognized. In the oceanic realm mild deformation concentrates in Domain I adjacent to the Tore-Madeira Rise. Domain 2 is characterized by the absence of shortening structures, except near the ocean-continent transition (OCT), implying that Miocene deformation did not propagate into the Abyssal Plain, In Domain 3 we distinguish three sub-domains: Sub-domain 3A which coincides with the OCT, Sub-domain 3B which is a highly deformed adjacent continental segment, and Sub-domain 3C. The Miocene tectonic inversion is mainly accommodated in Domain 3 by oceanwards directed thrusting at the ocean-continent transition and continentwards on the continental slope. Domain 4 corresponds to the non-rifted continental margin where only minor extensional and shortening deformation structures are observed. Finite element numerical models address the response of the various domains to the Miocene compression, emphasizing the long-wavelength differential vertical movements and the role of possible rheologic contrasts. The concentration of the Miocene deformation in the transitional zone (TC), which is the addition of Sub-domain 3A and part of 3B, is a result of two main factors: (1) focusing of compression in an already stressed region due to plate curvature and sediment loading; and (2) theological weakening. We estimate that the frictional strength in the TC is reduced in 30% relative to the surrounding regions. A model of compressive deformation propagation by means of horizontal impingement of the middle continental crust rift wedge and horizontal shearing on serpentinized mantle in the oceanic realm is presented. This model is consistent with both the geological interpretation of seismic data and the results of numerical modelling.

MDAI: Model based Design in Automobile Industry

It is proposed a new approach based on a methodology, assisted by a tool, to create new products in the automobile industry based on previous defined processes and experiences inspired on a set of best practices or principles: it is based on high-level models or specifications; it is component-based architecture centric; it is based on generative programming techniques. This approach follows in essence the MDA (Model Driven Architecture) philosophy with some specific characteristics. We propose a repository that keeps related information, such as models, applications, design information, generated artifacts and even information concerning the development process itself (e.g., generation steps, tests and integration milestones). Generically, this methodology receives the users' requirements to a new product (e.g., functional, non-functional, product specification) as its main inputs and produces a set of artifacts (e.g., design parts, process validation output) as its main output, that will be integrated in the engineer design tool (e.g. CAD system) facilitating the work.

New Steel Alloys for the Design of Heat Recovery Steam Generator Components of Combined Cycle Gas Plants

Demand for power is growing every day, mainly due to emerging economies in countries such as China, Russia, India, and Brazil. During the last 50 years steam pressure and temperature in power plants have been continuously raised to improve thermal efficiency. Recent efforts to improve efficiency leads to the development of a new generation of heat recovery steam generator, where the Benson once-through technology is applied to improve the thermal efficiency. The main purpose of this paper is to analyze the mechanical behavior of a high pressure superheater manifold by applying finite element modeling and a finite element analysis with the objective of analyzing stress propagation, leading to the study of damage mechanism, e.g., uniaxial fatigue, uniaxial creep for life prediction. The objective of this paper is also to analyze the mechanical properties of the new high temperature resistant materials in the market such as 2Cr Bainitic steels (T/P23 and T/P24) and also the 9-12Cr Martensitic steels (T/P91, T/P92, E911, and P/T122). For this study the design rules for construction of power boilers to define the geometry of the HPSH manifold were applied.

The role of European "ro-ro" port terminals in the automotive supply chain management

The aim of this paper is concerned with the design and development of a functional framework for maritime mode integration in European automotive supply chain management when considering outbound distribution. Furthermore, it provides a readjustment of traditional concepts and terminology with findings that the role of ro-ro port terminals should be considered as decoupling points, poles and postponement platforms. Case studies examine relevant Western European ro-ro port terminals for cars and respective links to assembly/factories of vehicles localized in the hinterland and concludes that ro-ro port terminals reduce logistical friction and impedance, as well as promote space/time compression.

Child-care attendance and common morbidity: evidence of association in the literature and questions of design

Papers on child-care attendance as a risk factor for acute respiratory infections and diarrhea were reviewed. There was great variety among the studies with regard to the design, definition of exposure and definition of outcomes. All the traditional epidemiological study designs have been used. The studies varied in terms of how child-care attendance in general was defined, and for different settings. These definitions differed especially in relation to the minimum time of attendance required. The outcomes were also defined and measured in several different ways. The analyses performed were not always appropriate, leading to sets of results of uneven quality, and composed of different measures of association relating different exposures and outcomes, that made summarizing difficult. Despite that, the results reported were remarkably consistent. Only two of the papers reviewed failed to show some association between child-care attendance and increased acute respiratory infections, or diarrhea. On the other hand, the magnitude of the associations reported varied widely, especially for lower respiratory infections. Taken together, the studies so far published provide evidence that children attending child-care centers, especially those under three years of age, are at a higher risk of upper respiratory infections, lower respiratory infections, and diarrhea. The studies were not consistent, however, in relation to attendance at child-care homes. Children in such settings were sometimes similar to those in child-care centers, sometimes similar to those cared for at home, and sometimes presented an intermediate risk.

Viability of Two New Mixture Design Methodologies for Self-Consolidating Concrete

This paper presents the results from an experimental study of the technical viability of two mixture designs for self-consolidating concrete (SCC) proposed by two Portuguese researchers in a previous work. The objective was to find the best method to provide the required characteristics of SCC in fresh and hardened states without having to experiment with a large number of mixtures. Five SCC mixtures, each with a volume of 25 L (6.61 gal.) were prepared using a forced mixer with a vertical axis for each of three compressive strength targets: 40, 55, and 70 MPa (5.80, 7.98, and 10.15 ksi). The mixtures' fresh state properties of fluidity, segregation resistance ability, and bleeding and blockage tendency, and their hardened state property of compressive strength were compared. For this study, the following tests were performed. slump-flow, V-funnel, L-box, box, and compressive strength. The results of this study made it possible to identify the most influential factors in the design of the SCC mixtures.

Acompanhamento dos trabalhos de construção de um hotel SANAHotels Amoreiras

Este trabalho final de mestrado baseou-se no acompanhamento da construção do hotel SANA Amoreiras, situado na Avenida Duarte Pacheco nº 12. O empreiteiro geral foi a empresa FDO Construções. Existindo também uma equipa de fiscalização, LMSA, contratada pelo Dono de Obra de forma a efectuar todo o controlo de qualidade. O TFM baseou-se no estágio efectuado para o Dono de obra do hotel onde fui devidamente acompanhada por uma engenheira, orientadora de estágio, que acompanhou de perto o desempenho da minha actividade. Esta função teve como objectivos a gestão de projecto de hotel, interligação entre projectistas e empreiteiro geral, bem prestar o devido acompanhamento de todos trabalhos a realizar. Acompanhei a realização de dois quartos modelo onde o objectivo do Dono de Obra foi testar as diversas soluções ao nível de revestimentos, sanitários, iluminação, mobiliário, decoração e outras soluções de arquitectura, soluções estas a implementar no hotel. Acompanhei também a realização de reuniões de compatibilização e coordenação de todos os projectos de especialidades com o projecto de arquitectura, nomeadamente Avac, Instalações eléctricas, Comunicações, Segurança, Águas, Esgotos, Gás, Incêndio, Cozinhas de forma a ser possível efectuar consultas aos empreiteiros e adjudicar todas estas empreitadas. Foi efectuada uma abordagem à descrição do hotel, suas características, indicação das razões que levaram à sua construção e descrição das várias empreitadas de construção realizadas até então, tal como, demolição, escavação, estrutura, acabamentos e especialidades.

Otimização de sistema de absorção, com coletores solares, para refrigeração de espaços condicionados termicamente (a chiller)

Nos dias que correm questões ambientais e considerações energéticas obrigam a uma inovação constante na procura de soluções de baixo consumo energético e de impacto ambiental baixo, nomeadamente no que diz respeito aos sistemas de climatização e refrigeração. Têm vindo a ser criadas medidas, tanto a nível internacional como nacional, no sentido de reduzir as emissões nocivas para a atmosfera, consequência do excessivo consumo de combustíveis fósseis, e do aumento da rentabilidade da energia e maior utilização de energias renováveis. O presente estudo de dimensionamento de um sistema de absorção, a brometo de lítio/água, com coletores solares, tem por base o sistema de compressão existente num edifício de serviços no centro de Lisboa. Foi efetuada uma analise simplificada dos seus dados de consumo energético, de maneira a verificar a viabilidade económica da substituição do equipamento existente e instalação de um sistema de coletores solares. Concluiu-se que a substituição do equipamento e a instalação de coletores solar, não é atrativa do ponto de vista económico, nesta solução em particular. Contudo, verifica-se uma considerável redução do impacto ambiental do consumo energético do edifício.

Design of a new test chamber for evaluation of the toxicity of rubber infill

A test chamber was projected and built (according to ISO 16000-9 Standard) to simulate atmospheric conditions experienced by rubber infill (when applied in synthetic turf pitches) and measure accurately the airborne emissions of pollutants such as dusts and volatile organic compounds (VOC), as well as pollutants present in leachates. It should be pointed out that standard ISO 16000-9 is only concerned with the determination of the emission of VOC from building products and furnishing (not specific of synthetic turf materials), whereas other standards are concerned with the emission of leachates only. This procedure is to be considered as a technical option to the lysimeter "global turf system evaluation" when the rubber infill alone is to be evaluated. The advantage of the proposed option considering this "test chamber" is its simplicity and economy. This test chamber is actually installed and being used for tests in LAIST.

Natural Gas location design and operation

A major determinant of the level of effective natural gas supply is the ease to feed customers, minimizing system total costs. The aim of this work is the study of the right number of Gas Supply Units – GSUs - and their optimal location in a gas network. This paper suggests a GSU location heuristic, based on Lagrangean relaxation techniques. The heuristic is tested on the Iberian natural gas network, a system modelized with 65 demand nodes, linked by physical and virtual pipelines. Lagrangean heuristic results along with the allocation of loads to gas sources are presented, using a 2015 forecast gas demand scenario.

TINSEL – a web-based intelligent tutoring system on electrical installation design

This paper presents a project consisting on the development of an Intelligent Tutoring System, for training and support concerning the development of electrical installation projects to be used by electrical engineers, technicians and students. One of the major goals of this project is to devise a teaching model based on Intelligent Tutoring techniques, considering not only academic knowledge but also other types of more empirical knowledge, able to achieve successfully the training of electrical installation design.

Addressing the facilities layout design problem through constraint logic programming

One of the most difficult problems that face researchers experimenting with complex systems in real world applications is the Facility Layout Design Problem. It relies with the design and location of production lines, machinery and equipment, inventory storage and shipping facilities. In this work it is intended to address this problem through the use of Constraint Logic Programming (CLP) technology. The use of Genetic Algorithms (GA) as optimisation technique in CLP environment is also an issue addressed. The approach aims the implementation of genetic algorithm operators following the CLP paradigm.

An intelligent tutoring approach to support students and technicians in electrical installation design

Designing electric installation projects, demands not only academic knowledge, but also other types of knowledge not easily acquired through traditional instructional methodologies. A lot of additional empirical knowledge is missing and so the academic instruction must be completed with different kinds of knowledge, such as real-life practical examples and simulations. On the other hand, the practical knowledge detained by the most experienced designers is not formalized in such a way that is easily transmitted. In order to overcome these difficulties present in the engineers formation, we are developing an Intelligent Tutoring System (ITS), for training and support concerning the development of electrical installation projects to be used by electrical engineers, technicians and students.