Traffic jam driving with NMV avoidance

n recent years, the development of advanced driver assistance systems (ADAS) – mainly based on lidar and cameras – has considerably improved the safety of driving in urban environments. These systems provide warning signals for the driver in the case that any unexpected traffic circumstance is detected. The next step is to develop systems capable not only of warning the driver but also of taking over control of the car to avoid a potential collision. In the present communication, a system capable of autonomously avoiding collisions in traffic jam situations is presented. First, a perception system was developed for urban situations—in which not only vehicles have to be considered, but also pedestrians and other non-motor-vehicles (NMV). It comprises a differential global positioning system (DGPS) and wireless communication for vehicle detection, and an ultrasound sensor for NMV detection. Then, the vehicle's actuators – brake and throttle pedals – were modified to permit autonomous control. Finally, a fuzzy logic controller was implemented capable of analyzing the information provided by the perception system and of sending control commands to the vehicle's actuators so as to avoid accidents. The feasibility of the integrated system was tested by mounting it in a commercial vehicle, with the results being encouraging.

Circuito de disparo de lámparas flash para la iluminación de sistemas fotovoltaicos

La medición y testeo de células fotovoltaicas en el laboratorio o en la industria exige reproducir unas condiciones de iluminación semejantes a las reales. Por eso se utilizan sistemas de iluminación basados en lámparas flash de Xenon que reproducen las condiciones reales en cuanto a nivel de irradiancia y espectro de la luz incidente. El objetivo de este proyecto es realizar los circuitos electrónicos necesarios para el disparo de dichas lámparas. El circuito de alimentación y disparo de una lámpara flash consta de una fuente de alimentación variable, un circuito de disparo para la ionización del gas Xenon y la electrónica de control. Nuestro circuito de disparo pretende producir pulsos adecuados para los dispositivos fotovoltaicos tanto en irradiancia, espectro y en duración, de forma que con un solo disparo consigamos el tiempo, la irradiancia y el espectro suficiente para el testeo de la célula fotovoltaica. La mayoría de estos circuitos exceptuando los específicos que necesita la lámpara, serán diseñados, simulados, montados en PCB y comprobados posteriormente en el laboratorio. ABSTRACT. Measurement and testing of photovoltaic cells in the laboratory or in industry requires reproduce lighting conditions similar to the real ones. So are used based lighting systems xenon flash lamps that reproduce the actual conditions in the level of irradiance and spectrum of the incident light. The objective of this project is to make electronic circuits required for such lamps shot. The power supply circuit and flash lamp shot consists of a variable power supply, a trigger circuit for Xenon gas ionization and the control electronics. Our shot circuit aims to produce pulses suitable for photovoltaic devices both irradiance, spectrum and duration, so that with a single shot get the time, the irradiance and spectrum enough for testing the photovoltaic cell. Most of these circuits except lamp specific requirements will be designed, simulated, and PCB mounted subsequently tested in the laboratory.

Temperature controlled light-emitting diode lamp for photovoltaic rural applications

In recent years, interest in light-emitting diode (LED) lighting has been growing because of its high efficacy, lifetime and ruggedness. This paper proposes a better adaptation of LED lamps to the technical requirements of photovoltaic lighting domestic systems, whose main quality criteria are reliability and that behave as voltage power supplies. As the key element of reliability in LED lamps is temperature, a solution is proposed for driving LED lamps using voltage sources, such as photovoltaic system batteries, with a control architecture based on pulse width modulation signal that regulates the current applied according to the LED lamp temperature. A prototype of the LED lamp has been implemented and tested to show its good performance at different temperatures and at different battery voltages.

A VLC-based beacon location system for mobile applications

This paper proposes a low cost and complexity indoor location and navigation system using visible light communications and a mobile device. LED lamps work as beacons transmitting an identifier code so a mobile device can know its location. Experimental designs for transmitter and receiver interfaces are presented and potential applications are discussed.

Discriminación del estado de la carretera mediante procesado acústico en vehículo

La rápida adopción de dispositivos electrónicos en el automóvil, ha contribuido a mejorar en gran medida la seguridad y el confort. Desde principios del siglo 20, la investigación en sistemas de seguridad activa ha originado el desarrollo de tecnologías como ABS (Antilock Brake System), TCS (Traction Control System) y ESP (Electronic Stability Program). El coste de despliegue de estos sistemas es crítico: históricamente, sólo han sido ampliamente adoptados cuando el precio de los sensores y la electrónica necesarios para su construcción ha caído hasta un valor marginal. Hoy en día, los vehículos a motor incluyen un amplio rango de sensores para implementar las funciones de seguridad. La incorporación de sistemas que detecten la presencia de agua, hielo o nieve en la vía es un factor adicional que podría ayudar a evitar situaciones de riesgo. Existen algunas implementaciones prácticas capaces de detectar carreteras mojadas, heladas y nevadas, aunque con limitaciones importantes. En esta tesis doctoral, se propone una aproximación novedosa al problema, basada en el análisis del ruido de rodadura generado durante la conducción. El ruido de rodadura es capturado y preprocesado. Después es analizado utilizando un clasificador basado en máquinas de vectores soporte (SVM), con el fin de generar una estimación del estado del firme. Todas estas operaciones se realizan en el propio vehículo. El sistema propuesto se ha desarrollado y evaluado utilizando Matlabr, mostrando tasas de aciertos de más del 90%. Se ha realizado una implementación en tiempo real, utilizando un prototipo basado en DSP. Después se han introducido varias optimizaciones para permitir que el sistema sea realizable usando un microcontrolador de propósito general. Finalmente se ha realizado una implementación hardware basada en un microcontrolador, integrándola estrechamente con las ECU del vehículo, pudiendo obtener datos capturados por los sensores del mismo y enviar las estimaciones del estado del firme. El sistema resultante ha sido patentado, y destaca por su elevada tasa de aciertos con un tamaño, consumo y coste reducidos. ABSTRACT Proliferation of automotive electronics, has greatly improved driving safety and comfort. Since the beginning of the 20th century, investigation in active safety systems has resulted in the development of technologies such as ABS (Antilock Brake System), TCS (Traction Control System) and ESP (Electronic Stability Program). Deployment cost of these systems is critical: historically, they have been widely adopted only when the price of the sensors and electronics needed to build them has been cut to a marginal value. Nowadays, motor vehicles include a wide range of sensors to implement the safety functions. Incorporation of systems capable of detecting water, ice or snow on the road is an additional factor that could help avoiding risky situations. There are some implementations capable of detecting wet, icy and snowy roads, although with important limitations. In this PhD Thesis, a novel approach is proposed, based on the analysis of the tyre/road noise radiated during driving. Tyre/road noise is captured and pre-processed. Then it is analysed using a Support Vector Machine (SVM) based classifier, to output an estimation of the road status. All these operations are performed on-board. Proposed system is developed and evaluated using Matlabr, showing success rates greater than 90%. A real time implementation is carried out using a DSP based prototype. Several optimizations are introduced enabling the system to work using a low-cost general purpose microcontroller. Finally a microcontroller based hardware implementation is developed. This implementation is tightly integrated with the vehicle ECUs, allowing it to obtain data captured by its sensors, and to send the road status estimations. Resulting system has been patented, and is notable because of its high hit rate, small size, low power consumption and low cost.

Estudio de la fiabilidad mediante ensayos acelerados de diodos ultravioletas de alta potencia

Durante los últimos años la utilización de los LEDs (Light Emitting Diodes) ha aumentado de forma muy importante siendo hoy en día una alternativa real a los sistemas de iluminación tradicionales. La iluminación basada en LEDs se está utilizando ampliamente en automoción, arquitectura, aplicaciones domésticas y señalización debido a su alta fiabilidad, pequeño tamaño y bajo consumo. La evaluación de la fiabilidad de los LEDs es un tema clave previo a la comercialización o a la puesta en marcha del LED en una nueva aplicación. La evaluación de la fiabilidad de dispositivos requiere ensayos acelerados para obtener resultados de fiabilidad en un periodo de tiempo aceptable, del orden de pocas semanas. En éste proyecto se estudia la fiabilidad de dos tipos diferentes de LEDs ultravioleta, que pueden sustituir a las lámparas UV convencionales, para diferentes condiciones de trabajo y diferentes condiciones ambientales. Se hace un seguimiento de la evolución de los LEDs UV durante cientos horas de ensayo acelerado para obtener resultados y conclusiones acerca de la degradación que sufren. La memoria del proyecto fin de carrera se ha estructurado en siete capítulos. Tres de ellos son teóricos, otros tres prácticos y finalmente uno sobre el presupuesto. El primero explica la introducción y la evolución del diodo LED, el segundo introduce la fiabilidad explicando los modelos más utilizados para analizar los ensayos y el tercero es un breve tema acerca de los ensayos acelerados. Los otros tres capítulos son orientados a los experimentos realizados en este Proyecto Fin de Carrera. Uno trata sobre la descripción del ensayo acelerado realizado, otro analiza los resultados obtenidos, el siguiente analiza las conclusiones y el último el presupuesto. ABSTRACT. For the last years, the use of LEDs (Light Emitting Diodes) has increased significantly, being nowadays a real alternative to traditional lighting systems. Lighting based on LEDs is being extensively used in automotive, domestic applications and signaling due to its high reliability small size and low power consumption. The evaluation of LEDs reliability is a key issue before marketing or launching a new application. The reliability evaluation of devices requires accelerated tests to obtain reliability results in an acceptable period of time, for the order of few weeks. In this project the reliability of two different types of UV LEDs, which can replace conventional UV lamps for different conditions and different environmental conditions is studied. The evolution of LEDs UV is tracked during hundred hours of accelerated test to obtain the results and conclusions about the degradation suffered. The memory of the final project has been structured into seven chapters. Three of them are theorical another three are experimental and the last one about estimates. The first explains the introduction and development of LED, the second introduces the reliability explaining the most used models to analyze the tests and the third is a brief topic about the accelerated tests. The other three chapters are oriented to the experiments done in this PFC. One explains the description of the accelerated test we have done, another analyzes the results obtained, the following one exposes the conclusions and the last one the estimates.

Implementación de sistema domótico con servidor Raspberry

Este proyecto consiste en el diseño e implementación un sistema domótico que puede ser instalado en una vivienda para controlar distintas variables ambientales y conseguir así la máxima comodidad de los habitantes de manera automática o manual según los gustos y necesidades de los usuarios. La característica principal de este sistema, es que cuenta con un funcionamiento distribuido donde entran en juego un servidor, encargado de tomar las decisiones generales para el comportamiento de la casa, y una serie de controladores esclavo cuya función es mantener constantes las variables ambientales con los valores fijados por el servidor. Así se consigue mantener la vivienda en una situación de bienestar constante para cualquier persona que se encuentre dentro. El sistema ha sido pensado de manera que se intenta reducir al máximo el cableado para facilitar su instalación por lo que la comunicación entre los distintos dispositivos se hace de manera inalámbrica por medio de un protocolo descrito en la norma IEEE 802.15.4 llamado ZigBee. Para ello se ha utilizado un módulo de comunicación wireless llamado Xbee, el cual permite la comunicación entre dos dispositivos. Para el control de dicho sistema distribuido se cuenta con una aplicación web, que mediante una interfaz gráfica permite al usuario controlar los distintos dispositivos dentro de la vivienda consiguiendo así controlar las variables ambientales a gusto del usuario. Dicha interfaz gráfica no depende de un software específico, sino que sólo es necesario un cliente http como podría ser Internet Explorer, Mozilla Firefox, Google Chrome, etc. Para integrar dicho sistema se ha usado un mini ordenador de bajo coste llamado RaspBerryPi, en el que se encuentra alojado un servidor Apache con el fin de gestionar y automatizar las variables ambientales. El control de los dipositivos encargados de modificar y estabilizar las variables ambientales se realiza mediante unos controladores genéricos implementados mediante mcontroladores 80C51F410, pertenecientes a la familia 80C51, y una serie de componentes y circuitería que permiten el correcto funcionamiento de éstos. Existen dos tipos de controladores distintos, los cuales son: Controlador Sensor: Encargados de las tomas de valores ambientales como puede ser la luz y la temperatura. Controladores Actuadores: Encargados de actuar sobre los dispositivos que modifican y estabilizan las variables ambientales como pueden ser la calefacción, tiras de leds de iluminación, persianas, alarmas, etc. El conjunto de la RaspBerryPi y los diferentes controladores forman el prototipo diseñado para este proyecto fin de carrera, el cual puede ser ampliado sencillamente para abarcar una amplia gama de posibilidades y funcionalidades dentro de la comodidad de una vivienda. ABSTRACT. The project described in this report consisted designing and implementing a home automation system that could be installed in a house in order to control environmental variables and thus get the maximum comfort of the inhabitant automatically or manually according to their tastes and needs. The main feature of this system consists in a distributed system, formed by a server which is responsible for making the main decisions of the actions performed inside the house. In addition, there are a series of slave controlers whose function consists in keeping the environmental variables within the values established by the server. Thus gets to keep the home in a situation of constant wellbeing to anyone who is inside. The system has been designed in order to reduce the amount of wire needed for the inter-connection of the devices, by means of wireless communication. The devices chosen for the solution are Xbee modules, which use the Zigbee protocol in order to comunicate one between each other. The Zigbee protocol is fully described in the IEEE 802.15.4 standard. A web application has been used to control the distributed system. This application allows users to control various devices inside the house and subsequently the different environmental variables. This implementation allows obtaining the maximum comfort by means of a very simple graphical interface. In addition, the Graphical User Interface (GUI) does not depend on any specific software. This means that it would only be necessary a http client (such as Internet Explorer, Mozilla Firefox, Google Chrome, etc.) for handling the application. The system has been integrated using a low-cost mini computer called RaspBerryPi.This computer has an Apache server allocated which allows to manage and to automatize the different environmental variables. Furthermore, for changing and stabilizing those variables, some generic controllers have been developed, based on mcontrollers 80C51F410. There have been developed mainly two different types of controllers: Sensor Controllers, responsible for measuring the different environmental values, such as light and temperature; and Actuator Controllers, which purpose is to modify and stabilize those environmental variables by actuating on the heating, the led lamps, the blinders, the alarm, etc. The combination of the RaspBerryPi and the different controllers conform the prototype designed during this project. Additionally, this solution could be easily expanded in order to intake further functionalities adapted to new needs that could arise in the future.

Merit function for the evaluation of color uniformity in the far field of LED spot lights

The scope of the present paper is the derivation of a merit function which predicts the visual perception of LED spot lights. The color uniformity level Usl is described by a linear regression function of the spatial color distribution in the far field. Hereby, the function is derived from four basic functions. They describe the color uniformity of spot lights through different features. The result is a reliable prediction for the perceived color uniformity in spot lights. A human factor experiment was performed to evaluate the visual preferences for colors and patterns. A perceived rank order was derived from the subjects’ answers and compared with the four basic functions. The correlation between the perceived rank order and the basic functions was calculated resulting in the definition of the merit function Usl. The application of this function is shown by a comparison of visual evaluations and measurements of LED retrofit spot lamps. The results enable a prediction of color uniformity levels of simulations and measurements concerning the visual perception. The function provides a possibility to evaluate the far field of spot lights without individual subjective judgment. © (2014) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

Road Dust Emission Sources and Assessment of Street Washing Effect

Although previous studies report on the effect of street washing on ambient particulate matter levels, there is a lack of studies investigating the results of street washing on the emission strength of road dust. A sampling campaign was conducted in Madrid urban area during July 2009 where road dust samples were collected in two sites, namely Reference site (where the road surface was not washed) and Pelayo site (where street washing was performed daily during night). Following the chemical characterization of the road dust particles the emission sources were resolved by means of Positive Matrix Factorization, PMF (Multilinear Engine scripting) and the mass contribution of each source was calculated for the two sites. Mineral dust, brake wear, tire wear, carbonaceous emissions and construction dust were the main sources of road dust with mineral and construction dust being the major contributors to inhalable road dust load. To evaluate the effectiveness of street washing on the emission sources, the sources mass contributions between the two sites were compared. Although brake wear and tire wear had lower concentrations at the site where street washing was performed, these mass differences were not statistically significant and the temporal variation did not show the expected build-up after dust removal. It was concluded that the washing activities resulted merely in a road dust moistening, without effective removal and that mobilization of particles took place in a few hours between washing and sampling. The results also indicated that it is worth paying attention to the dust dispersed from the construction sites as they affect the emission strength in nearby streets.

Papyrus, EATOP, and MetaEdit+: a comparison between the EAST-ADL modeling tools

Several Architecture Description Languages (ADLs) are emerging as models to describe and represent system architectures. Among others, EAST-ADL language is highlighted. It represents an abstraction of embedded software systems for automobiles. Given the need to implement the EAST-ADL language, there are many modeling tools to perform this task. The scope of this thesis is a detailed comparison of three EAST-ADL editors: Papyrus, EATOP and MetaEdit +, providing a conceptual framework, describing the comparison criteria, and finally exemplifying thanks to the Brake-By-Wire use case which has been provided, and whose development is not the subject of this project. The motivation for developing this project is to provide comparison guide between these three modeling tools to facilitate developers choice when deciding the tool in which develop their work. RESUMEN. Diversos Lenguajes de Descripción de Arquitecturas (ADLs) están surgiendo como modelos para describir y representar arquitecturas de sistemas. Entre ellos es destacado el lenguaje EAST-ADL, que representa una abstracción de los sistemas de software embebido para automóviles. Ante la necesidad de implementar el lenguaje EAST-ADL, han surgido diversas herramientas de modelado que llevan a cabo esta tarea. El alcance de este proyecto consiste en una comparación detallada de tres editores EAST-ADL: Papyrus, EATOP y MetaEdit+, proporcionando un marco conceptual, describiendo los criterios de comparación y finalmente ejemplificando con el caso de uso Brake-By-Wire que nos ha sido proporcionado, y cuyo desarrollo no es sujeto de este proyecto. La motivación para desarrollar este proyecto parte de proporcionar al usuario una guía comparativa de estas tres herramientas de modelado para facilitar su elección a la hora de desarrollar su trabajo.

Validación de HP UV-LED para la detección en continuo de contaminantes en aguas continentales mediante fluorescencia

La preservación del medio ambiente, el avance en las técnicas para que el impacto de la actividad humana sobre la fauna y flora sea lo menor posible, hacen que se deban monitorizar los diversos indicadores de calidad. El presente estudio viene motivado debido a que actualmente existen sistemas de medida y control en continuo de la calidad de las aguas, al margen de los estudios de laboratorio por toma de muestras, a través de los cuales se obtienen indicadores de calidad. El desarrollo tecnológico en analizadores en continuo para la medida de fósforo, amonio, DBO y otros, hacen que cada vez se consiga un control más exhaustivo de la calidad en tiempo real. Sin embargo, la detección temprana de contaminantes que no deben encontrarse presentes en el agua, hacen que el desarrollo de sensores de detección de estos contaminantes sea de gran utilidad. A este respecto, las técnicas mediante fluorescencia presentan enormes ventajas, ya que no existe contacto directo con la muestra, reduciéndose el desgaste y alargando el tiempo entre mantenimientos, como se ha comprobado en numerosos desarrollos con tecnología láser. Para la producir fluorescencia, tradicionalmente se vienen utilizando en el laboratorio principalmente lámparas de gas y monocromadores. Los nuevos LED de alta potencia en el espectro ultravioleta son una alternativa muy interesante que además puede ser aplicada en los mencionados sistemas de medición en continuo. En este trabajo se realiza un estudio de viabilidad de estos dispositivos como fuentes de excitación para la producción de fluorescencia tomando como contaminantes los hidrocarburos. El funcionamiento en estaciones en continuo hace que se tenga que realizar además ensayos de vida acelerados, así como estudios de modos de trabajo. Al respecto de la fluorescencia producida, se estudia la influencia de factores que pueden afectar a las medidas, tales como la temperatura. El estudio del espectro y su análisis para la identificación del contaminante es otro de los puntos desarrollados en este trabajo. Por último, y dado que la monitorización se realiza en modo continuo, es necesario un sistema de comunicaciones compacto y fiable: en este apartado se analizan los metamateriales como solución tecnológica, ya que se adapta perfectamente a la filosofía de estas estaciones de medición. ABSTRACT Currently the monitoring of quality indicators is a need to preserve the environment and minimize the impact of human activity on the fauna and flora. Currently there are measuring systems and continuous monitoring of water quality, regardless of sampling laboratory studies, through which quality indicators are obtained. Technological development in continuous analyzers for the measurement of phosphorus, ammonia, BOD and others increasingly make a more comprehensive real-time quality control is achieved. However, early detection of contaminants that should not be present in the water, make the development of sensors for detecting these contaminants is very useful. In this regard, fluorescence techniques have huge advantages, since there is no direct contact with the sample, reducing wear and extending the time between maintenance, as has been demonstrated in numerous developments in laser technology. To produce fluoresce, traditionally are being used mainly gas lamps and monochromators at the laboratory. The new high-power LEDs in the ultraviolet spectrum are a very interesting alternative that can also be applied in the above continuous measurement systems. In this paper a viability study of these devices as excitation sources to produce fluorescence using hydrocarbon as contaminants is performed. The stations in continuous operation makes it necessary to also perform accelerated life tests and studies operating modes. In regard to the fluorescence produced, the influence of factors that may affect the measurements, such as temperature is studied. The study of the spectrum and analysis to identify the contaminant is another of the points developed in this work. Finally, since the monitoring is carried out in continuous mode, a compact and reliable communication is necessary: in this section metamaterials as a technological solution is analyzed since it fits perfectly with the philosophy of these measuring stations.

Análisis paramétrico determinista y aleatorio de problemas dinámicos en estructuras aeroespaciales

Los fenómenos dinámicos pueden poner en peligro la integridad de estructuras aeroespaciales y los ingenieros han desarrollado diferentes estrategias para analizarlos. Uno de los grandes problemas que se plantean en la ingeniería es cómo atacar un problema dinámico estructural. En la presente tesis se plantean distintos fenómenos dinámicos y se proponen métodos para estimar o simular sus comportamientos mediante un análisis paramétrico determinista y aleatorio del problema. Se han propuesto desde problemas sencillos con pocos grados de libertad que sirven para analizar las diferentes estrategias y herramientas a utilizar, hasta fenómenos muy dinámicos que contienen comportamientos no lineales, daños y fallos. Los primeros ejemplos de investigación planteados cubren una amplia gama de los fenómenos dinámicos, como el análisis de vibraciones de elementos másicos, incluyendo impactos y contactos, y el análisis de una viga con carga armónica aplicada a la que también se le añaden parámetros aleatorios que pueden responder a un desconocimiento o incertidumbre de los mismos. Durante el desarrollo de la tesis se introducen conceptos y se aplican distintos métodos, como el método de elementos finitos (FEM) en el que se analiza su resolución tanto por esquemas implícitos como explícitos, y métodos de análisis paramétricos y estadísticos mediante la técnica de Monte Carlo. Más adelante, una vez ya planteadas las herramientas y estrategias de análisis, se estudian fenómenos más complejos, como el impacto a baja velocidad en materiales compuestos, en el que se busca evaluar la resistencia residual y, por lo tanto, la tolerancia al daño de la estructura. Se trata de un suceso que puede producirse por la caída de herramienta, granizo o restos en la pista de aterrizaje. Otro de los fenómenos analizados también se da en un aeropuerto y se trata de la colisión con un dispositivo frangible, el cual tiene que romperse bajo ciertas cargas y, sin embargo, soportar otras. Finalmente, se aplica toda la metodología planteada en simular y analizar un posible incidente en vuelo, el fenómeno de la pérdida de pala de un turbohélice. Se trata de un suceso muy particular en el que la estructura tiene que soportar unas cargas complejas y excepcionales con las que la aeronave debe ser capaz de completar con éxito el vuelo. El análisis incluye comportamientos no lineales, daños, y varios tipos de fallos, y en el que se trata de identificar los parámetros clave en la secuencia del fallo. El suceso se analiza mediante análisis estructurales deterministas más habituales y también mediante otras técnicas como el método de Monte Carlo con el que se logran estudiar distintas incertidumbres en los parámetros con variables aleatorias. Se estudian, entre otros, el tamaño de pala perdida, la velocidad y el momento en el que se produce la rotura, y la rigidez y resistencia de los apoyos del motor. Se tiene en cuenta incluso el amortiguamiento estructural del sistema. Las distintas estrategias de análisis permiten obtener unos resultados valiosos e interesantes que han sido objeto de distintas publicaciones. ABSTRACT Dynamic phenomena can endanger the integrity of aerospace structures and, consequently, engineers have developed different strategies to analyze them. One of the major engineering problems is how to deal with the structural dynamics. In this thesis, different dynamic phenomena are introduced and several methods are proposed to estimate or simulate their behaviors. The analysis is considered through parametric, deterministic and statistical methods. The suggested issues are from simple problems with few degrees of freedom, in order to develop different strategies and tools to solve them, to very dynamic phenomena containing nonlinear behaviors failures, damages. The first examples cover a wide variety of dynamic phenomena such as vibration analysis of mass elements, including impacts and contacts, and beam analysis with harmonic load applied, in which random parameters are included. These parameters can represent the unawareness or uncertainty of certain variables. During the development of the thesis several concepts are introduced and different methods are applied, such as the finite element method (FEM), which is solved through implicit and explicit schemes, and parametrical and statistical methods using the Monte Carlo analysis technique. Next, once the tools and strategies of analysis are set out more complex phenomena are studied. This is the case of a low-speed impact in composite materials, the residual strength of the structure is evaluated, and therefore, its damage tolerance. This incident may occur from a tool dropped, hail or debris throw on the runway. At an airport may also occur, and it is also analyzed, a collision between an airplane and a frangible device. The devise must brake under these loads, however, it must withstand others. Finally, all the considered methodology is applied to simulate and analyze a flight incident, the blade loss phenomenon of a turboprop. In this particular event the structure must support complex and exceptional loads and the aircraft must be able to successfully complete the flight. Nonlinear behavior, damage, and different types of failures are included in the analysis, in which the key parameters in the failure sequence are identified. The incident is analyzed by deterministic structural analysis and also by other techniques such as Monte Carlo method, in which it is possible to include different parametric uncertainties through random variables. Some of the evaluated parameters are, among others, the blade loss size, propeller rotational frequency, speed and angular position where the blade is lost, and the stiffness and strength of the engine mounts. The study does also research on the structural damping of the system. The different strategies of analysis obtain valuable and interesting results that have been already published.

Co-simulation Methodologies for Hybrid and Electric Vehicle Dynamics

In recent decades, full electric and hybrid electric vehicles have emerged as an alternative to conventional cars due to a range of factors, including environmental and economic aspects. These vehicles are the result of considerable efforts to seek ways of reducing the use of fossil fuel for vehicle propulsion. Sophisticated technologies such as hybrid and electric powertrains require careful study and optimization. Mathematical models play a key role at this point. Currently, many advanced mathematical analysis tools, as well as computer applications have been built for vehicle simulation purposes. Given the great interest of hybrid and electric powertrains, along with the increasing importance of reliable computer-based models, the author decided to integrate both aspects in the research purpose of this work. Furthermore, this is one of the first final degree projects held at the ETSII (Higher Technical School of Industrial Engineers) that covers the study of hybrid and electric propulsion systems. The present project is based on MBS3D 2.0, a specialized software for the dynamic simulation of multibody systems developed at the UPM Institute of Automobile Research (INSIA). Automobiles are a clear example of complex multibody systems, which are present in nearly every field of engineering. The work presented here benefits from the availability of MBS3D software. This program has proven to be a very efficient tool, with a highly developed underlying mathematical formulation. On this basis, the focus of this project is the extension of MBS3D features in order to be able to perform dynamic simulations of hybrid and electric vehicle models. This requires the joint simulation of the mechanical model of the vehicle, together with the model of the hybrid or electric powertrain. These sub-models belong to completely different physical domains. In fact the powertrain consists of energy storage systems, electrical machines and power electronics, connected to purely mechanical components (wheels, suspension, transmission, clutch…). The challenge today is to create a global vehicle model that is valid for computer simulation. Therefore, the main goal of this project is to apply co-simulation methodologies to a comprehensive model of an electric vehicle, where sub-models from different areas of engineering are coupled. The created electric vehicle (EV) model consists of a separately excited DC electric motor, a Li-ion battery pack, a DC/DC chopper converter and a multibody vehicle model. Co-simulation techniques allow car designers to simulate complex vehicle architectures and behaviors, which are usually difficult to implement in a real environment due to safety and/or economic reasons. In addition, multi-domain computational models help to detect the effects of different driving patterns and parameters and improve the models in a fast and effective way. Automotive designers can greatly benefit from a multidisciplinary approach of new hybrid and electric vehicles. In this case, the global electric vehicle model includes an electrical subsystem and a mechanical subsystem. The electrical subsystem consists of three basic components: electric motor, battery pack and power converter. A modular representation is used for building the dynamic model of the vehicle drivetrain. This means that every component of the drivetrain (submodule) is modeled separately and has its own general dynamic model, with clearly defined inputs and outputs. Then, all the particular submodules are assembled according to the drivetrain configuration and, in this way, the power flow across the components is completely determined. Dynamic models of electrical components are often based on equivalent circuits, where Kirchhoff’s voltage and current laws are applied to draw the algebraic and differential equations. Here, Randles circuit is used for dynamic modeling of the battery and the electric motor is modeled through the analysis of the equivalent circuit of a separately excited DC motor, where the power converter is included. The mechanical subsystem is defined by MBS3D equations. These equations consider the position, velocity and acceleration of all the bodies comprising the vehicle multibody system. MBS3D 2.0 is entirely written in MATLAB and the structure of the program has been thoroughly studied and understood by the author. MBS3D software is adapted according to the requirements of the applied co-simulation method. Some of the core functions are modified, such as integrator and graphics, and several auxiliary functions are added in order to compute the mathematical model of the electrical components. By coupling and co-simulating both subsystems, it is possible to evaluate the dynamic interaction among all the components of the drivetrain. ‘Tight-coupling’ method is used to cosimulate the sub-models. This approach integrates all subsystems simultaneously and the results of the integration are exchanged by function-call. This means that the integration is done jointly for the mechanical and the electrical subsystem, under a single integrator and then, the speed of integration is determined by the slower subsystem. Simulations are then used to show the performance of the developed EV model. However, this project focuses more on the validation of the computational and mathematical tool for electric and hybrid vehicle simulation. For this purpose, a detailed study and comparison of different integrators within the MATLAB environment is done. Consequently, the main efforts are directed towards the implementation of co-simulation techniques in MBS3D software. In this regard, it is not intended to create an extremely precise EV model in terms of real vehicle performance, although an acceptable level of accuracy is achieved. The gap between the EV model and the real system is filled, in a way, by introducing the gas and brake pedals input, which reflects the actual driver behavior. This input is included directly in the differential equations of the model, and determines the amount of current provided to the electric motor. For a separately excited DC motor, the rotor current is proportional to the traction torque delivered to the car wheels. Therefore, as it occurs in the case of real vehicle models, the propulsion torque in the mathematical model is controlled through acceleration and brake pedal commands. The designed transmission system also includes a reduction gear that adapts the torque coming for the motor drive and transfers it. The main contribution of this project is, therefore, the implementation of a new calculation path for the wheel torques, based on performance characteristics and outputs of the electric powertrain model. Originally, the wheel traction and braking torques were input to MBS3D through a vector directly computed by the user in a MATLAB script. Now, they are calculated as a function of the motor current which, in turn, depends on the current provided by the battery pack across the DC/DC chopper converter. The motor and battery currents and voltages are the solutions of the electrical ODE (Ordinary Differential Equation) system coupled to the multibody system. Simultaneously, the outputs of MBS3D model are the position, velocity and acceleration of the vehicle at all times. The motor shaft speed is computed from the output vehicle speed considering the wheel radius, the gear reduction ratio and the transmission efficiency. This motor shaft speed, somehow available from MBS3D model, is then introduced in the differential equations corresponding to the electrical subsystem. In this way, MBS3D and the electrical powertrain model are interconnected and both subsystems exchange values resulting as expected with tight-coupling approach.When programming mathematical models of complex systems, code optimization is a key step in the process. A way to improve the overall performance of the integration, making use of C/C++ as an alternative programming language, is described and implemented. Although this entails a higher computational burden, it leads to important advantages regarding cosimulation speed and stability. In order to do this, it is necessary to integrate MATLAB with another integrated development environment (IDE), where C/C++ code can be generated and executed. In this project, C/C++ files are programmed in Microsoft Visual Studio and the interface between both IDEs is created by building C/C++ MEX file functions. These programs contain functions or subroutines that can be dynamically linked and executed from MATLAB. This process achieves reductions in simulation time up to two orders of magnitude. The tests performed with different integrators, also reveal the stiff character of the differential equations corresponding to the electrical subsystem, and allow the improvement of the cosimulation process. When varying the parameters of the integration and/or the initial conditions of the problem, the solutions of the system of equations show better dynamic response and stability, depending on the integrator used. Several integrators, with variable and non-variable step-size, and for stiff and non-stiff problems are applied to the coupled ODE system. Then, the results are analyzed, compared and discussed. From all the above, the project can be divided into four main parts: 1. Creation of the equation-based electric vehicle model; 2. Programming, simulation and adjustment of the electric vehicle model; 3. Application of co-simulation methodologies to MBS3D and the electric powertrain subsystem; and 4. Code optimization and study of different integrators. Additionally, in order to deeply understand the context of the project, the first chapters include an introduction to basic vehicle dynamics, current classification of hybrid and electric vehicles and an explanation of the involved technologies such as brake energy regeneration, electric and non-electric propulsion systems for EVs and HEVs (hybrid electric vehicles) and their control strategies. Later, the problem of dynamic modeling of hybrid and electric vehicles is discussed. The integrated development environment and the simulation tool are also briefly described. The core chapters include an explanation of the major co-simulation methodologies and how they have been programmed and applied to the electric powertrain model together with the multibody system dynamic model. Finally, the last chapters summarize the main results and conclusions of the project and propose further research topics. In conclusion, co-simulation methodologies are applicable within the integrated development environments MATLAB and Visual Studio, and the simulation tool MBS3D 2.0, where equation-based models of multidisciplinary subsystems, consisting of mechanical and electrical components, are coupled and integrated in a very efficient way.

Haus des Rundfunks en Berlin, de Hans Poelzig, 1930

Poelzig affirmed that the technical ideal consisted of using the least amount of shapes and materials possible. He understood architecture as an art, as the expression of form; In contrast to the indifference of the most widely recognized values of modernism: technical innovation in construction along with the functionality of buildings. The Haus des Rundfunks is a powerful hermetic factory in the shape of a triangle and of uniform height. Mass, geometric rigidity and the absence of textures make up a building which relinquishes expressing the new media, with a perimeter ring consisting of offices and larger spaces that are more characteristic towards their inside. Geometry is used as a means to organize and limit the shapes of the buildings. The arrangement and division of different intercommunicating spaces are subjected to the crudeness of their geometric limits. Interior spaces ranging from the most static to the most dynamic are defined through the qualities of materials and geometries. This turns the spaces into geometric grids which decompose the wall, floor and ceiling planes into fragments, regardless of the constructive reality provided by a metallic frame structure. Its polyhedral lamps enclose artificial and emphasize the value of the grid. Poelzig limits himself to dealing with planes within a closed volume of uniform height, and maintains geometric rigidity compatible with a certain degree of figurativeness. This article tries to bring to life this exemplary building, marked by its passivity and hermetism.

NA PALMA DA MÃO: A difusão de celulares e smartphones e possibilidades para o ensino-aprendizagem no Brasil

A pesquisa considera a difusão de celulares e smartphones e as consequências deste fato em possibilidades para o ensino-aprendizagem. Aparatos de comunicação sempre estiveram ligados ao processo de ensino-aprendizagem. Entretanto, com o desenvolvimento mais intenso, nas últimas décadas, das Tecnologias de Informação e Comunicação (TIC), essa relação vem ganhando novos contornos. Surge a Internet, a evolução das máquinas computacionais e, recentemente, a explosão dos dispositivos móveis, fornecendo novos produtos e serviços convergentes. Nesse contexto, celulares e smartphones tem sido utilizados e recomendados para apoio e complemento do processo de ensino-aprendizagem: a chamada Aprendizagem Móvel. Esse ramo cresce devido à rápida expansão e barateamento dessas tecnologias na sociedade. Para verificar cientificamente essa relação foi realizada uma pesquisa de natureza qualitativa, do tipo exploratória, com dois projetos de Aprendizagem Móvel em andamento no Brasil, o Palma – Programa de Alfabetização na Língua Materna e o Escola Com Celular – ECC. Assim, a partir dos dados provenientes da pesquisa, identificamos alguns aspectos relacionados ao uso de celulares e smartphones para o processo de ensino-aprendizagem que contribuem na compreensão desse campo ainda em construção no Brasil. O uso desses dispositivos como suporte para processos de ensino-aprendizagem nos projetos estudados é delineado pelos aspectos tecnologia, dispositivo, público e contexto e novas tecnologias e Aprendizagem Móvel. O aspecto dispositivo desdobra-se em dimensões como disseminação, multifuncionalidade e acessibilidade que embasam os projetos, ainda favorece características apontadas como importantes para o processo de ensino-aprendizagem na atualidade, como mobilidade e portabilidade. Os projetos pesquisados demonstram potencial e metodologia adequada aos contextos para os quais foram criados e aplicados. Entretanto, a pesquisa indicou que ao mesmo tempo em que celulares e smartphones representam o ápice da convergência tecnológica e são considerados extremamente populares e acessíveis na sociedade contemporânea, com possibilidades concretas como nos projetos estudados, não conseguiram conquistar uma posição sólida como suporte para o ensino-aprendizagem. Tal indicação se deve, de acordo com o corpus, à carência de alguns fatores, como: fomento, as práticas se mostram extremamente dependentes da iniciativa pública ou privada para sua extensão e continuidade; sensibilização para o uso de tecnologias disponíveis, não consideram o aparelho dos próprios alunos e um planejamento que inclua, capacite e incentive o uso desses dispositivos. Além disso, a pesquisa também destaca a necessidade de uma visão crítica do uso e papel da tecnologia nesses processos.