Budget issues : effects of the fiscal year 1990 sequester on the Department of Health and Human Services : fact sheet for the Chairman, Committee on Budget, House of Representatives /

"B-240472"--p.1.

Tax administration : information on IRS' Criminal Investigation Division, fact sheet to the chairman of the Subcommittee on Oversight, Committee on Ways and Means, House of Representatives /

Cover title.

Side lights on the Reign of Terror; being the memoirs of Mademoiselle Des Écherolles trans. from the French by Marie Clothilde Balfour.

Mode of access: Internet.

Travels in Norway, Sweden, Finland, Russia and Turkey; also on the coasts of the sea of Azof and of the Black sea; with a review of the trade in those seas, and of the systems adopted to man the fleets of the different powers of Europe, compared with that of England.

Mode of access: Internet.

The story of the peasant-boy philosopher; or, "The child gathering pebbles on the sea-shore." (Founded on the early life of Ferguson, the shephard-boy astronomer, and intended to show how a poor lad became acquainted with the principles of natural science.)

Mode of access: Internet.

Report on the Lancashire Sea-Fisheries Laboratory at the University of Liverpool, and the Sea-Fish Hatchery at Piel

Merged Into Liverpool Biological Society. Proceedings and Transactions

On the chemical side of nervous activity.

Mode of access: Internet.

A memoir on the subject of a navigation act, including the encouragement of the manufactory of boats and sea vessels, and the protection of mariners.

Mode of access: Internet.

Mince pie : adventures on the sunny side of Grub Street /

Reprinted in part from various periodicals.

A catalogue of plants & shells found in the vicinity of Milwaukee on the west side of Lake Michigan /

Several pages blank throughout.

The United Nations Convention on the Law of the Sea : hearing before the Committee on International Relations, House of Representatives, One Hundred Eighth Congress, second session, May 12, 2004.

"Serial no. 108-136."

The Wnt receptor Ryk is required for Wnt5a-mediated axon guidance on the contralateral side of the corpus callosum

Ryk (receptor related to tyrosine kinase) has been shown to be a novel Wnt receptor in both Caenorhabditis elegans and Drosophila melanogaster. Recently, Ryk-Wnt interactions were shown to guide corticospinal axons down the embryonic mouse spinal cord. Here we show that, in Ryk-deficient mice, cortical axons project aberrantly across the major forebrain commissure, the corpus callosum. Many mouse mutants have been described in which loss-of-function mutations result in the inability of callosal axons to cross the midline, thereby forming Probst bundles on the ipsilateral side. In contrast, loss of Ryk does not interfere with the ability of callosal axons to cross the midline but impedes their escape from the midline into the contralateral side. Therefore, Ryk(-/-) mice display a novel callosal guidance phenotype. We also show that Wnt5a acts as a chemorepulsive ligand for Ryk, driving callosal axons toward the contralateral hemisphere after crossing the midline. In addition, whereas callosal axons do cross the midline in Ryk(-/-) embryos, they are defasciculated on the ipsilateral side, indicating that Ryk also promotes fasciculation of axons before midline crossing. In summary, this study expands the emerging role for Wnts in axon guidance and identifies Ryk as a key guidance receptor in the establishment of the corpus callosum. Our analysis of Ryk function further advances our understanding of the molecular mechanisms underlying the formation of this important commissure.

Mechanical properties of sheet metal under forming conditions

In the bulge test, a sheet metal specimen is clamped over a circular hole in a die and formed into a bulge by the hydraulic pressure on one side of the specirnen. As the unsupported part of the specimen is deformed in this way, its area is increased, in other words, the material is generally stretched and its thickness generally decreased. The stresses causing this stretching action are the membrane stresses in the shell generated by the hydraulic pressure, in the same way as the rubber in a toy balloon is stretched by the membrane stresses caused by the air inside it. The bulge test is a widely used sheet metal test, to determine the "formability" of sheet materials. Research on this forming process (2)-(15)* has hitherto been almost exclusively confined to predicting the behaviour of the bulged specimen through the constitutive equations (stresses and strains in relation to displacements and shapes) and empirical work hardening characteristics of the material as determined in the tension test. In the present study the approach is reversed; the stresses and strains in the specimen are measured and determined from the geometry of the deformed shell. Thus, the bulge test can be used for determining the stress-strain relationship in the material under actual conditions in sheet metal forming processes. When sheet materials are formed by fluid pressure, the work-piece assumes an approximately spherical shape, The exact nature and magnitude of the deviation from the perfect sphere can be defined and measured by an index called prolateness. The distribution of prolateness throughout the workpiece at any particular stage of the forming process is of fundamental significance, because it determines the variation of the stress ratio on which the mode of deformation depends. It is found. that, before the process becomes unstable in sheet metal, the workpiece is exactly spherical only at the pole and at an annular ring. Between the pole and this annular ring the workpiece is more pointed than a sphere, and outside this ring, it is flatter than a sphere. In the forming of sheet materials, the stresses and hence the incremental strains, are closely related to the curvatures of the workpiece. This relationship between geometry and state of stress can be formulated quantitatively through prolateness. The determination of the magnitudes of prolateness, however, requires special techniques. The success of the experimental work is due to the technique of measuring the profile inclination of the meridional section very accurately. A travelling microscope, workshop protractor and surface plate are used for measurements of circumferential and meridional tangential strains. The curvatures can be calculated from geometry. If, however, the shape of the workpiece is expressed in terms of the current radial (r) and axial ( L) coordinates, it is very difficult to calculate the curvatures within an adequate degree of accuracy, owing to the double differentiation involved. In this project, a first differentiation is, in effect, by-passed by measuring the profile inclination directly and the second differentiation is performed in a round-about way, as explained in later chapters. The variations of the stresses in the workpiece thus observed have not, to the knowledge of the author, been reported experimentally. The static strength of shells to withstand fluid pressure and their buckling strength under concentrated loads, both depend on the distribution of the thickness. Thickness distribution can be controlled to a limited extent by changing the work hardening characteristics of the work material and by imposing constraints. A technique is provided in this thesis for determining accurately the stress distribution, on which the strains associated with thinning depend. Whether a problem of controlled thickness distribution is tackled by theory, or by experiments, or by both combined, the analysis in this thesis supplies the theoretical framework and some useful experimental techniques for the research applied to particular problems. The improvement of formability by allowing draw-in can also be analysed with the same theoretical and experimental techniques. Results on stress-strain relationships are usually represented by single stress-strain curves plotted either between one stress and one strain (as in the tension or compression tests) or between the effective stress and effective strain, as in tests on tubular specimens under combined tension, torsion and internal pressure. In this study, the triaxial stresses and strains are plotted simultaneously in triangular coordinates. Thus, both stress and strain are represented by vectors and the relationship between them by the relationship between two vector functions. From the results so obtained, conclusions are drawn on both the behaviour and the properties of the material in the bulge test. The stress ratios are generally equal to the strain-rate ratios (stress vectors collinear with incremental strain vectors) and the work-hardening characteristics, which apply only to the particular strain paths are deduced. Plastic instability of the material is generally considered to have been reached when the oil pressure has attained its maximum value so that further deformation occurs under a constant or lower pressure. It is found that the instability regime of deformation has already occurred long before the maximum pressure is attained. Thus, a new concept of instability is proposed, and for this criterion, instability can occur for any type of pressure growth curves.

An analysis of the effect of process parameters on the formability of sheet metal

This investigation is in two parts, theory and experimental verification. (1) Theoretical Study In this study it is, for obvious reasons, necessary to analyse the concept of formability first. For the purpose of the present investigation it is sufficient to define the four aspects of formability as follows: (a) the formability of the material at a critical section, (b) the formability of the material in general, (c) process efficiency, (d) proportional increase in surface area. A method of quantitative assessment is proposed for each of the four aspects of formability. The theoretical study also includes the distinction between coaxial and non-coaxial strains which occur, respectively, in axisymmetrical and unsymmetrical forming processes and the inadequacy of the circular grid system for the assessment of formability is explained in the light of this distinction. (2) Experimental Study As one of the bases of the experimental work, the determination of the end point of a forming process, which sets the limit to the formability of the work material, is discussed. The effects of three process parameters on draw-in are shown graphically. Then the delay of fracture in sheet metal forming resulting from draw-in is analysed in kinematical terms, namely, through the radial displacements, the radial and the circumferential strains, and the projected thickness of the workpiece. Through the equilibrium equation of the membrane stresses, the effect on the shape of the unsupported region of the workpiece, and hence the position of the critical section is explained. Then, the effect of draw-in on the four aspects of formability is discussed throughout this investigation. The triangular coordinate system is used to present and analyse the triaxial strains involved. This coordinate system has the advantage of showing all the three principal strains in a material simultaneously, as well as representing clearly the many types of strains involved in sheet metal work.