Optimization of amaranth flour films plasticized with glycerol and sorbitol by multi-response analysis

The optimal formulation for the preparation of amaranth flour films plasticized with glycerol and sorbitol was obtained by a multi-response analysis. The optimization aimed to achieve films with higher resistance to break, moderate elongation and lower solubility in water. The influence of plasticizer concentration (Cg, glycerol or Cs, sorbitol) and process temperature (Tp) on the mechanical properties and solubility of the amaranth flour films was initially studied by response surface methodology (RSM). The optimized conditions obtained were Cg 20.02 g glycerol/100 g flour and Tp 75 degrees C, and Cs 29.6 g sorbitol/100 g flour and Tp 75 degrees C. Characterization of the films prepared with these formulations revealed that the optimization methodology employed in this work was satisfactory. Sorbitol was the most suitable plasticizer. It furnished amaranth flour films that were more resistant to break and less permeable to oxygen, due to its greater miscibility with the biopolymers present in the flour and its lower affinity for water. (C) 2011 Elsevier Ltd. All rights reserved.

Thermomechanical properties of biodegradable films based on blends of gelatin and poly(vinyl alcohol)

The aim of this work was to study the effect of the poly(vinyl alcohol) (PVA) concentration on the thermal and viscoelastic properties of films based on blends of gelatin and PVA using differential scanning calorimetry (DSC) and dynamic-mechanical analysis (DMA). One glass transition was observed between 43 and 49 degrees C on the DSC curves obtained in the first scanning of the blended films, followed by fusion of the crystalline portion between 116 and 134 degrees C. However, the DMA results showed that only the films with 10% PVA had a single peak in the tan 5 spectrum. However, when the PVA concentration was increased the dynamic mechanical spectra showed two peaks on the tan 6 curves, indicating two T(g)s. Despite this phase separation behavior the Gordon and Taylor model was successfully applied to correlate T, as a function of film composition, thus determining k = 7.47. In the DMA frequency tests, the DMA spectra showed that the storage modulus values decreased with increasing temperature. The master curves for the PVA-gelatin films were obtained applying the TTS principle (T(r) = 100 degrees C). The WLF model was thus applied allowing for the determination of the constants C(1) and C(2). The values of these constants increased with increasing PVA concentrations in the blend: C(1) = 49-66 and C(2) = 463-480. These values were used to calculate the fractional free volume of the films at the T(g) and the thermal expansion coefficient of the films above the T(g). (c) 2007 Elsevier Ltd. All rights reserved.

Polymorphism, crystallinity and hydrophilic-lipophilic balance of stearic acid and stearic acid-capric/caprylic triglyceride matrices for production of stable nanoparticles

There is an increasing interest in lipid nanoparticles because of their suitability for several administration routes. Thus, it becomes even more relevant the physicochemical characterization of lipid materials with respect to their polymorphism, lipid miscibility and stability, as well as the assessment of the effect of surfactant on the type and structure of these nanoparticles. This work focuses on the physicochemical characterization of lipid matrices composed of pure stearic acid or of mixtures of stearic acid-capric/caprylic triglycerides, for drug delivery. The lipids were analyzed by Differential Scanning Calorimetry (DSC), Wide Angle X-ray Diffraction (WAXD), Polarized Light Microscopy (PLM) and hydrophilic-lipophilic balance (HLB) in combination with selected surfactants to determine the best solid-to-liquid ratio. Based on the results obtained by DSC and WAXD, the selected qualitative and quantitative composition contributed for the production of stable nanoparticles, since the melting and the tempering processes provided important information on the thermodynamic stability of solid lipid matrices. The best HLB value obtained for stearic acid-capric/caprylic triglycerides was 13.8, achieved after combining these lipids with accepted surfactants (trioleate sorbitan and polysorbate 80 in the ratio of 10:90). The proposed combinations were shown useful to obtain a stable emulsion to be used as intermediate form for the production of lipid nanoparticles. (C) 2011 Elsevier B.V. All rights reserved.

Vesicles with charged domains

This work summarizes results obtained on membranes composed of the ternary mixture dioleoylphosphatidylglycerol (DOPG), egg sphingomyelin (eSM) and cholesterol (Chol). The membrane phase state as a function of composition is characterized from data collected with fluorescence microscopy on giant unilamellar vesicles. The results suggest that the presence of the charged DOPG significantly decreases the composition region of coexistence of liquid ordered and liquid disordered phases as compared to that in the ternary mixture of dioleoylphosphatidycholine, sphingomyelin and cholesterol. The addition of calcium chloride to DOPG:eSM:Chol vesicles, and to a lesser extent the addition of sodium chloride, leads to the stabilization of the two-phase coexistence region, which is expressed in an increase in the miscibility temperature. On the other hand, addition of the chelating agent EDTA has the opposite effect, suggesting that impurities of divalent cations in preparations of giant vesicles contribute to the stabilization of charged domains. We also explore the behavior of these membranes in the presence of extruded unilamellar vesicles made of the positively charged lipid dioleoyltrimethylammoniumpropane (DOTAP). The latter can induce domain formation in DOPG:eSM:Chol vesicles with initial composition in the one-phase region. (C) 2010 Elsevier B.V. All rights reserved.

Hybrid materials from intermolecular associations between cationic lipid and polymers

Intermolecular associations between a cationic lipid and two model polymers were evaluated from preparation and characterization of hybrid thin films cast on silicon wafers. The novel materials were prepared by spin-coating of a chloroformic solution of lipid and polymer on silicon wafer. Polymers tested for miscibility with the cationic lipid dioctadecyldimethylammonium bromide (DODAB) were polystyrene (PS) and poly(methyl methacrylate) (PMMA). The films thus obtained were characterized by ellipsometry, wettability, optical and atomic force microscopy, Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and activity against Escherichia coli. Whereas intermolecular ion-dipole interactions were available for the PMMA-DODAB interacting pair producing smooth PMMA-DODAB films, the absence of such interactions for PS-DODAB films caused lipid segregation, poor film stability (detachment from the silicon wafer) and large rugosity. In addition, the well-established but still remarkable antimicrobial DODAB properties were transferred to the novel hybrid PMMA/DODAB coating, which is demonstrated to be highly effective against E. coli.

Polymeric electro-mechanic devices applied to antibiotic-controlled release

Polymeric electroactive blends formed by electropolymerized aniline inside a non-conductive polyacrylamide porous matrix were already shown as suitable materials for the electrocontrolled release of model compounds like safranin. In this paper the intermolecular interactions between the two components of the blend are put in evidence by Raman spectroscopy measurements. Also, in situ optical microscopy was used to follow changes occurring in the polyaniline/polyacrylamide blend during pyrocathecol violet release tests. These two sets of experiments show the possibility of controlling electrochemically the release of both, safranin (a cation) and pyrocathecol violet (an anion) and allow to infer a release mechanism based on the electromechanical properties of the blends explaining the dependence of the release kinetics on the applied potential. Tetracycline release curves for different potentials and pHs are shown and the obtained profiles are in agreement with those expected for a device acting as an electrochemically driven pump due to the artificial muscle properties of the conducting phase of the blends. (c) 2007 Elsevier B.V. All rights reserved.

Tailored Media for Homogeneous Cellulose Chemistry: Ionic Liquid/Co-Solvent Mixtures

Co-solvents can minimize two of the major problems associated with the use of ionic liquids (ILs) as solvents for homogeneous derivatization of cellulose: high viscosity and limited miscibility with non-polar reagents or reaction products. Thus, the effects of 18 solvents and 3 binary solvent mixtures on cellulose solutions in three ILs were systematically studied with respect to the solution phase behavior. The applicable limits of these mixtures were evaluated and general guidelines for the use of co-solvents in cellulose chemistry could be advanced: Appropriate co-solvents should have EN T values (normalized empirical polarity) > 0.3, very low ``acidity`` (alpha < 0.5), and relatively high ""basicity`` (beta >= 0.4). Moreover, novel promising co-solvents and binary co-solvent mixtures were identified.

Optimization of the rheological properties of probiotic yoghurts supplemented with milk proteins

This study aimed to optimize the rheological properties of probiotic yoghurts supplemented with skimmed milk powder (SMP) whey protein concentrate (WPC) and sodium caseinate (Na-Cn) by using an experimental design type simplex-centroid for mixture modeling It Included seven batches/trials three were supplemented with each type of the dairy protein used three corresponding to the binary mixtures and one to the ternary one in order to increase protein concentration in 1 g 100 g(-1) of final product A control experiment was prepared without supplementing the milk base Processed milk bases were fermented at 42 C until pH 4 5 by using a starter culture blend that consisted of Streptococcus thermophilus Lactobacillus delbrueckii subsp bulgaricus and Bifidobacterium (Humans subsp lactis The kinetics of acidification was followed during the fermentation period as well the physico-chemical analyses enumeration of viable bacteria and theological characteristics of the yoghurts Models were adjusted to the results (kinetic responses counts of viable bacteria and theological parameters) through three regression models (linear quadratic and cubic special) applied to mixtures The results showed that the addition of milk proteins affected slightly acidification profile and counts of S thermophilus and B animal`s subsp lactis but it was significant for L delbrueckii subsp bulgaricus Partially-replacing SMP (45 g/100 g) with WPC or Na-Cn simultaneously enhanced the theological properties of probiotic yoghurts taking into account the kinetics of acidification and enumeration of viable bacteria (C) 2010 Elsevier Ltd All rights reserved

Wettability of Aqueous Rhamnolipids Solutions Produced by Pseudomonas aeruginosa LBI

The wetting behavior of rhamnolipids produced by Pseudomonas aeruginosa LBI strain grown on waste oil substrate and sodium dodecyl sulfate (SDS) on glass, polyethylene terephthalate (PET), poly(vinyl chloride) (PVC), poly(epsilon-caprolactone) (PCL) and polymer blend (PVC-PCL) was investigated by the measuring contact angle of sessile drops, to determine the wetting characteristics of rhamnolipids. The comparison of the wetting profiles showed that at low SDS and rhamnolipid concentrations, the contact angle increased and when the concentration of the surfactant increased further, the contact angle decreased. The blend surface (PVC-PCL) showed better wettability than the homopolymers themselves and the blend changed the surface hydrophobicity of the polymer, making it more hydrophilic. The rhamnolipids produced by the LBI strain exhibited superior wetting abilities than the chemical surfactant SDS one. This is the first work that evaluates the wetting properties of rhamnolipids on polymer blends.

Biobased films prepared from NaOH/thiourea aqueous solution of chitosan and linter cellulose

In the present study, films based on linter cellulose and chitosan were prepared using an aqueous solution of sodium hydroxide (NaOH)/thiourea as the solvent system. The dissolution process of cellulose and chitosan in NaOH/thiourea aqueous solution was followed by the partial chain depolymerization of both biopolymers, which facilitates their solubilization. Biobased films with different chitosan/cellulose ratios were then elaborated by a casting method and subsequent solvent evaporation. They were characterized by X-ray analysis, scanning electron microscopy (SEM), atomic force microscopy (AFM), thermal analysis, and tests related to tensile strength and biodegradation properties. The SEM images of the biofilms with 50/50 and 60/40 ratio of chitosan/cellulose showed surfaces more wrinkled than the others. The AFM images indicated that higher the content of chitosan in the biobased composite film, higher is the average roughness value. It was inferred through thermal analysis that the thermal stability was affected by the presence of chitosan in the films; the initial temperature of decomposition was shifted to lower levels in the presence of chitosan. Results from the tests for tensile strength indicated that the blending of cellulose and chitosan improved the mechanical properties of the films and that an increase in chitosan content led to production of films with higher tensile strength and percentage of elongation. The degradation study in a simulated soil showed that the higher the crystallinity, the lower is the biodegradation rate.

Towards to the trans-bromination of 2-styrylpyridine with a palladacycle intermediary and structure analysis for trans-1,2-dibromo-2-styrylpyridine

The simple halogenation of alkynes in conventional organic reactions gives a blend of cis and trans isomers. It is proposed then, a synthesis of stereospecific halogenation of alkynes in trans position, using palladacycle as intermediaries. The recrystallization of the compound obtained by bromination of 2-Styrylpyridine, with cyclepalladium intermediary results in a single crystal, which is subjected to X-ray diffraction. The crystal packing is established through weak interactions of three types. The first one is of the type pi x pi interactions, from symmetry operation, between the centroids. The second one is of the type C-X center dot center dot center dot pi interactions. And the last type is an anomalous intermolecular interaction between halogens, C-X center dot center dot center dot X-C, with bond distances smaller than the sum of the van der Waals radii. The conformation on the C=C bond is trans and the dihedral angle between the aromatic rings is (with esd approximate) 18.1(3)degrees. (C) 2010 Elsevier B.V. All rights reserved.

Experimentell studie på kostnadseffektiva inkjetbestrykningspigment

The objective of this study was to evaluate and compare the print performance of some of the new most promising, cost effective absorbent pigments specialised for inkjet coatings on the market in a continuous drive to find an alternative to silica. The target was a lower production cost for ArjoWiggins inkjet products, OMD 01 and OMD 02. Five absorbent pigments are being evaluated through measuring the qualities of the coating mix itself, visual evaluations of print performance and physical testing of the coated paper. Pigments 1,2 and 3, which all are said to be tailored for inkjet coatings, did not reach the print performance needed for an OMD 01 and OMD 02 equal, due to severe bleed and feathering identified especially on the Epson 950 printer. They are therefore currently not seen as viable formulations. A blend of 50% pigment 5 and 50% silica had excellent print performance as OMD 01 and OMD 02 equivalents and is therefore recommended as a potential alternative to 100% silica. It is of the company’s interest to find a more cost effective solution to their inkjet coatings, and a 50/50 blend of Pigment 5 will save the company more than 35 000 euro per year.

Estudo do processo de congelamento de camarão associado ao uso do aditivo fosfato

Os objetivos gerais desta tese foram a otimização do processo de congelamento do camarão, e a avaliação do efeito da adição do fosfato que pode afetar o rendimento e a qualidade do produto, conforme percebido pelo consumidor final. Inicialmente, foi feito um levantamento da capacidade tecnológica das empresas de pescado do Brasil. A seguir, foi feita uma revisão da literatura, buscando entender as variáveis que afetam o processo de congelamento do pescado, particularmente as questões associadas ao uso do fosfato no processamento do camarão. Após a revisão da literatura, foi elaborado um planejamento experimental, onde foi possível obter dados referentes ao rendimento (evolução do peso do produto) em cada etapa estudada: imersão em soluções de fosfato, congelamento, descongelamento e cocção. Os melhores rendimentos foram obtidos pelo congelamento com N2 líquido e com o uso de fosfato. A partir desses resultados preliminares, encontrou-se o ajuste ótimo dos fatores analisados e, a partir dele, foram executados novos ensaios para a validação das previsões de rendimento e complementação do estudo através de análises químicas e sensoriais. O uso de fosfato mostrou-se eficaz na retenção de água no descongelamento e após a cocção. Observou-se menor perda de peso no descongelamento do camarão tratado com blend de fosfato (-1,87 %) quando comparado com o Tripolifosfato de sódio – TPF (-2,86%) e controle (imersão em água, -15,5%) O mesmo foi verificado após a cocção: Blend (-7,61%), TPF (-9,05%) e controle (-25,3%). Esses rendimentos foram comprovados com a diminuição da perda de exsudado (drip loss) no descongelamento e após a cocção, o aumento do teor de umidade após a imersão em fosfato e a sua retenção após o descongelamento e cocção. Os níveis residuais de fosfato (TPF e blend) estavam abaixo do limite 0,5% estabelecido pela legislação internacional. Os resultados da análise sensorial demonstraram que o camarão tratado com fosfato reteve os atributos sensoriais, contribuindo, assim, para a maior preferência e aceitação pelos julgadores.

Utilização do modelo de Black-Litterman para gestão de hedge funds do Brasil

O modelo Black-Litterman calcula os retornos esperados de mercado como uma combinação de um conjunto de expectativas específicas de cada investidor e um ponto de referência neutro. A combinação dessas duas fontes de informações são feitas pelo modelo utilizando a abordagem bayesiana. Os resultados obtidos a partir do modelo Black-Litterman, ao contrário da abordagem tradicional, são bastante intuitivos, estáveis e consistentes em relação as expectativas dos investidores. O objetivo dessa dissertação é fazer uma análise detalhada de cada um dos componentes do modelo Black-Litterman e verificar se a utilização o modelo de Black-Litterman, introduzindo as opiniões de mercado com base no relatório FOCUS do Banco Central, supera o retorno dos fundos multimercados brasileiros.

Competitividade dos biocombustíveis no Brasil: uma comparação entre os principais biocombustíveis etanol e biodisel

As preocupações mundiais com o aquecimento global e os efeitos nocivos da utilização de combustíveis fósseis têm fomentado a busca por novos modelos energéticos, baseados em fontes limpas e renováveis, com destaque para os biocombustíveis. Sem menos importância, o esgotamento das reservas mundiais de matérias-primas fósseis, somado às instabilidades geopolíticas nas principais regiões produtoras, impulsionam, cada vez mais, o desenvolvimento destes novos modelos. Neste cenário, o Brasil tem papel de destaque. Líder mundial na produção e consumo de etanol à base de cana-de-açúcar, o país iniciou, em 2005, a inclusão de mais uma fonte de energia renovável em sua matriz energética: a mistura do biodiesel no diesel mineral. O presente trabalho tem como objetivo analisar a competitividade dos principais biocombustíveis brasileiros: o etanol e o biodiesel. Em primeiro lugar, estes produtos foram analisados quanto às suas principais características; em segundo, avaliou-se a competitividade econômica destes combustíveis frente a seus produtos substitutos diretos derivados do petróleo. Finalmente, foram analisados os benefícios (tangíveis e intangíveis) inerentes à utilização dos biocombustíveis, e como estes intangíveis deveriam ser precificados, como forma de atribuir um prêmio aos benefícios que trazem ao meio-ambiente e à sociedade. Esta dissertação pretende servir de base para uma avaliação mais profunda da real competitividade econômica dos biocombustíveis frente aos combustíveis derivados do petróleo, além de colocar em cheque as principais análises atuais e críticas sobre a utilização destes produtos. Além disso, o presente trabalho visa avaliar o potencial e as limitações da produção dos biocombustíveis no Brasil.