State alcohol related fatality rates.

Mode of access: Internet.

A simulator study of the combined effects of alcohol and marihuana on driving behavior. Phase II. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

A simulator study of the combined effects of alcohol and marihuana on driving behavior. Phase I. Final report.

Mode of access: Internet.

Validation of assembled nucleic acid-based tests in diagnostic microbiology laboratories

Medical microbiology and virology laboratories use nucleic acid tests (NAT) to detect genomic material of infectious organisms in clinical samples. Laboratories choose to perform assembled (or in-house) NAT if commercial assays are not available or if assembled NAT are more economical or accurate. One reason commercial assays are more expensive is because extensive validation is necessary before the kit is marketed, as manufacturers must accept liability for the performance of their assays, assuming their instructions are followed. On the other hand, it is a particular laboratory's responsibility to validate an assembled NAT prior to using it for testing and reporting results on human samples. There are few published guidelines for the validation of assembled NAT. One procedure that laboratories can use to establish a validation process for an assay is detailed in this document. Before validating a method, laboratories must optimise it and then document the protocol. All instruments must be calibrated and maintained throughout the testing process. The validation process involves a series of steps including: (i) testing of dilution series of positive samples to determine the limits of detection of the assay and their linearity over concentrations to be measured in quantitative NAT; (ii) establishing the day-to-day variation of the assay's performance; (iii) evaluating the sensitivity and specificity of the assay as far as practicable, along with the extent of cross-reactivity with other genomic material; and (iv) assuring the quality of assembled assays using quality control procedures that monitor the performance of reagent batches before introducing new lots of reagent for testing.

Genetic time-series analysis identifies a major QTL for in vivo alcohol metabolism not predicted by in vitro studies of structural protein polymorphism at the ADH1B or ADH1C loci

After ingestion of a standardized dose of ethanol, alcohol concentrations were assessed, over 3.5 hours from blood (six readings) and breath (10 readings) in a sample of 412 MZ and DZ twins who took part in an Alcohol Challenge Twin Study (ACTS). Nearly all participants were subsequently genotyped on two polymorphic SNPs in the ADH1B and ADH1C loci known to affect in vitro ADH activity. In the DZ pairs, 14 microsatellite markers covering a 20.5 cM region on chromosome 4 that includes the ADH gene family were assessed, Variation in the timed series of autocorrelated blood and breath alcohol readings was studied using a bivariate simplex design. The contribution of a quantitative trait locus (QTL) or QTL's linked to the ADH region was estimated via a mixture of likelihoods weighted by identity-by-descent probabilities. The effects of allelic substitution at the ADH1B and ADH1C loci were estimated in the means part of the model simultaneously with the effects sex and age. There was a major contribution to variance in alcohol metabolism due to a QTL which accounted for about 64% of the additive genetic covariation common to both blood and breath alcohol readings at the first time point. No effects of the ADH1B*47His or ADH1C*349Ile alleles on in vivo metabolism were observed, although these have been shown to have major effects in vitro. This implies that there is a major determinant of variation for in vivo alcohol metabolism in the ADH region that is not accounted for by these polymorphisms. Earlier analyses of these data suggested that alcohol metabolism is related to drinking behavior and imply that this QTL may be protective against alcohol dependence.

Smoking and elevated blood pressure are the most important risk factors for subarachnoid hemorrhage in the Asia-Pacific region - An overview of 26 cohorts involving 306,620 participants

Background and Purpose - The cause of subarachnoid hemorrhage ( SAH) is poorly understood and there are few large cohort studies of risk factors for SAH. We investigated the risk of SAH mortality and morbidity associated with common cardiovascular risk factors in the Asia-Pacific region and examined whether the strengths of these associations were different in Asian and Australasian ( predominantly white) populations. Methods - Cohort studies were identified from Internet electronic databases, searches of proceedings of meetings, and personal communication. Hazard ratios (HRs) for systolic blood pressure (SBP), current smoking, total serum cholesterol, body mass index (BMI), and alcohol drinking were calculated from Cox models that were stratified by sex and cohort and adjusted for age at risk. Results - Individual participant data from 26 prospective cohort studies ( total number of participants 306 620) that reported incident cases of SAH ( fatal and/or nonfatal) were available for analysis. During the median follow-up period of 8.2 years, a total of 236 incident cases of SAH were observed. Current smoking (HR, 2.4; 95% CI, 1.8 to 3.4) and SBP > 140 mm Hg ( HR, 2.0; 95% CI, 1.5 to 2.7) were significant and independent risk factors for SAH. Attributable risks of SAH associated with current smoking and elevated SBP ( similar to 140 mm Hg) were 29% and 19%, respectively. There were no significant associations between the risk of SAH and cholesterol, BMI, or drinking alcohol. The strength of the associations of the common cardiovascular risk factors with the risk of SAH did not differ much between Asian and Australasian regions. Conclusions - Cigarette smoking and SBP are the most important risk factors for SAH in the Asia-Pacific region.

Misleading high tobramycin plasma concentrations can be caused by skin contamination of fingerprick blood following inhalation of nebulized tobramycin (TOBI (R)) - A short report

We observed unexpected high plasma concentrations of tobrarriycin (48.5 and 28.1 mg/L) in fingerprick blood samples after the nebulization of tobramycin solution for inhalation (tobramycin 300 mg/5 mL, TOBI(R)) by 2 young children aged 3 years. To investigate whether dermal contamination could be the source of error, 3 adult volunteers were present during another nebulization by a third child (age 2 years). The volunteers had exposure to tobramycin by handling the nebulizer or the nebule and also by inhalation from holding the child and being in close proximity while TOBI(R) was being administered. Five blood samples by fingerprick and 2 by venipuncture were collected and assayed for tobramycin concentration. On each occasion the site was swabbed with alcohol wipes to mimic standard patient sampling methods. One site was resampled after cleaning of hands with 2% chlorhexidine gluconate and water. Tobramycin concentrations from venipuncture 1-2 hours after nebulization were all < 0.2 mg/L except for 1 result of 1.2 mg/L. The tobramycin concentrations from fingerpricks before hand washing varied between 6.8 and 172 mg/L, and after hand washing between 0.3 and 17.6 mg/L. Contamination of fingers with tobramycin is likely to have caused the error in the 2 initial cases and did cause misleadingly elevated levels in the adult volunteers. We caution that therapeutic drug monitoring of nebulized tobramycin should not be done by fingerprick sampling, and care should be taken to avoid contamination of the venipuncture site.

Legislative and regulatory measures for preventing alcohol-related drownings and near-drownings

Objective: Alcohol contributes to about 30% of drowning fatalities associated with recreational aquatic activity and to 35% of drownings associated with boating. We consider regulatory and legislative strategies for preventing such deaths. Methods: We contacted water police in each Australian State and Territory to identify legislation creating alcohol-related offences for operators of recreational boats in their jurisdiction and to determine whether they conducted random breath testing (RBT). We also sought information from all 152 (81 urban and 71 rural) local government councils in NSW regarding restrictions on consumption of alcohol in public places within their shires. Results: Four Australian States (New South Wales, Queensland, Victoria and South Australia) have legislation prescribing maximum blood alcohol concentrations (BACs) for operators of recreational boats; all support this with RBT Western Australia, Tasmania and the Australian Capital Territory define more general offences for operating vessels while under the influence, of alcohol. Prohibitions or restrictions on consumption of alcohol in public places exist in 78 of the 86 shires in NSW that responded: 69 councils had alcohol-free zones, 53 restricted consumption of alcohol in public parks and reserves, and 33 had prohibitions or restrictions in some aquatic environments. Conclusions/implications: Legislation restricting BACs for recreational boat operators should be adopted in all Australian States and Territories. Optimal legislation would require that all occupants of recreational boats are required to comply with prescribed BAC levels, including when vessels are at anchor. Extension of by-laws prohibiting or restricting the consumption of alcohol specifically in aquatic environments warrants consideration.

Number and type of substances in alcohol and drug-related completed suicides in an Australian sample

Background: The association between substance use and suicide is well-established, but evidence is scant regarding the relationship between the number, type, and level of substances and other risk factors in completed suicide across the lifespan. Aims: To examine the relationship between social/demographic characteristics and the number, type, and level of drugs present in an unrestricted age sample of completed suicides in Australia. Method: An analysis was undertaken of 893 substance-related suicides using data from the Government Statistician's Office for the years 1989-1992. Results: The number and type of substances present in suicide victims was related to the individual's gender, age, marital status, employment status, and method of suicide. Blood alcohol level was significantly different between the methods of suicide, but was unrelated to demographic characteristics of the individual. The level of antidepressants and minor tranquilizers in the individuals was also unrelated to demographic characteristics. Conclusion: Examination of the type and number of substances present in completed suicides is an important component in creating profiles of potential suicide victims.

Heritability and Stability of Resting Blood Pressure in Australian Twins

In Australian twins participating in three different studies (1979-1996), the contribution of genetic and environmental influences to variation in resting systolic (SBP) and diastolic blood pressure (DBP) was studied. The sample consisted of 368 monozygotic and 335 dizygotic twin pairs with measurements for both individuals. Blood pressure measurements in two studies were available for 115 complete twin pairs, and 49 twin pairs had measurements in three studies. This allowed assessment of blood pressure tracking over an average period of 12 years in the age range of 23 to 45 years. Multivariate analyses showed significant heritability (h(2)) of blood pressure in all studies (SBP h(2) = 19%-56%, DBP h(2) = 37%-52%). In addition, the analyses showed that the blood pressure tracking was explained by the same set of genetic factors. These results replicate an earlier finding in Dutch twins that also showed stability of the contribution of genetic factors to blood pressure tracking.

Blood type classification using computer vision and machine learning

In emergency situations, where time for blood transfusion is reduced, the O negative blood type (the universal donor) is administrated. However, sometimes even the universal donor can cause transfusion reactions that can be fatal to the patient. As commercial systems do not allow fast results and are not suitable for emergency situations, this paper presents the steps considered for the development and validation of a prototype, able to determine blood type compatibilities, even in emergency situations. Thus it is possible, using the developed system, to administer a compatible blood type, since the first blood unit transfused. In order to increase the system’s reliability, this prototype uses different approaches to classify blood types, the first of which is based on Decision Trees and the second one based on support vector machines. The features used to evaluate these classifiers are the standard deviation values, histogram, Histogram of Oriented Gradients and fast Fourier transform, computed on different regions of interest. The main characteristics of the presented prototype are small size, lightweight, easy transportation, ease of use, fast results, high reliability and low cost. These features are perfectly suited for emergency scenarios, where the prototype is expected to be used.

Range of self-tests available to buy in the United Kingdom: an Internet survey

We aimed to describe the availability in the United Kingdom of self-tests that are used to diagnose or screen for conditions without involving a health professional. A systematic Internet search identified 104 unique self-tests related to 24 named conditions including cancers, chronic conditions and infections. These self-tests require various samples including blood obtained using a lancet. The samples are processed at home with results available in minutes or sent to a laboratory for processing with results returned to the individual by e-mail or post. Prices per self-test and condition range from <1 pound to 76 pound. Self-tests are readily available, and further work is needed to assess their impact.

Evaluation of a 2% chlorhexidine gluconate in 70% isopropyl alcohol skin disinfectant

The efficacy of a new skin disinfectant, 2% (w/v) chlorhexidine gluconate (CHG) in 70% (v/v) isopropyl alcohol (IPA) (ChloraPrep®), was compared with five commonly used skin disinfectants against Staphylococcus epidermidis RP62A in the presence or absence of protein, utilizing quantitative time-kill suspension and carrier tests. All six disinfectants [70% (v/v) IPA, 0.5% (w/v) aqueous CHG, 2% (w/v) aqueous CHG, 0.5% (w/v) CHG in 70% (v/v) IPA and 10% (w/v) aqueous povidone iodine (PI)] achieved a log10 reduction factor of 5, in colony-forming units/mL, in a suspension test (exposure time 30 s) in the presence and absence of 10% human serum. Subsequent challenges of S. epidermidis RP62A in a biofilm (with and without human serum) demonstrated reduced bactericidal activity. Overall, the most effective skin disinfectants tested against S. epidermidis RP62A were 2% (w/v) CHG in 70% IPA and 10% (w/v) PI. These results suggest that enhanced skin antisepsis may be achieved with 2% (w/v) CHG in 70% (v/v) IPA compared with the three commonly used CHG preparations [0.5% (w/v) aqueous CHG, 2% (w/v) aqueous CHG and 0.5% (w/v) CHG in 70% (v/v) IPA]. © 2005 The Hospital Infection Society. Published by Elsevier Ltd. All rights reserved.

The acceptability of alcohol fuels for automobile engines

The aim of this project was to carry out an investigastion into suitable alternatives to gasoline for use in modern automobiles. The fuel would provide the western world with a means of extending the natural gasoline resources and the third world a way of cutting down their dependence on the oil producing countries for their energy supply. Alcohols, namely methanol and ethanol, provide this solution. They can be used as gasoline extenders or as fuels on their own.In order to fulfil the aims of the project a literature study was carried out to investigate methods and costs of producing these fuels. An experimental programme was then set up in which the performance of the alcohols was studied on a conventional engine. The engine used for this purpose was the Fiat 127 930cc four cylinder engine. This engine was used because of its popularity in the European countries. The Weber fixed jet carburettor, since it was designed to be used with gasoline, was adapted so that the alcohol fuels and the blends could be used in the most efficient way. This was mainly to take account of the lower heat content of the alcohols. The adaptation of the carburettor was in the form of enlarging the main metering jet. Allowances for the alcohol's lower specfic gravity were made during fuel metering.Owing to the low front end volatility of methanol and ethanol, it was expected that `start up' problems would occur. An experimental programme was set up to determine the temperature range for a minimum required percentage `take off' that would ease start-up since it was determined that a `take off' of about 5% v/v liquid in the vapour phase would be sufficient for starting. Additions such as iso-pentane and n-pentane were used to improve the front end volatility. This proved to be successful.The lower heat content of the alcohol fuels also meant that a greater charge of fuel would be required. This was seen to pose further problems with fuel distribution from the carburettor to the individual cylinders on a multicylinder engine. Since it was not possible to modify the existing manifold on the Fiat 127 engine, experimental tests on manifold geometry were carried out using the Ricardo E6 single cylinder variable compression engine. Results from these tests showed that the length, shape and cross-sectional area of the manifold play an important part in the distribution of the fuel entering the cylinder, ie. vapour phase, vapour/small liquid droplet/liquid film phase, vapour/large liquid droplet/liquid film phase etc.The solvent properties of the alcohols and their greater electrical conductivity suggested that the materials used on the engine would be prone to chemical attack. In order to determine the type and rate of chemical attack, an experimental programme was set up whereby carburettor and other components were immersed in the alcohols and in blends of alcohol with gasoline. The test fuels were aerated and in some instances kept at temperatures ranging from 50oC to 90oC. Results from these tests suggest that not all materials used in the conventional engine are equally suitable for use with alcohols and alcohol/gasoline blends. Aluminium for instance was severely attacked by methanol causing pitting and pin-holing in the surface.In general this whole experimental programme gave valuable information on the acceptability of substitute fuels. While the long term effects of alcohol use merit further study, it is clear that methanol and ethanol will be increasingly used in place of gasoline.

Requirement for and optimisation of premium intraocular lenses

Premium intraocular lenses (IOLs) aim to surgically correct astigmatism and presbyopia following cataract extraction, optimising vision and eliminating the need for cataract surgery in later years. It is usual to fully correct astigmatism and to provide visual correction for distance and near when prescribing spectacles and contact lenses, however for correction with the lens implanted during cataract surgery, patients are required to purchase the premium IOLs and pay surgery fees outside the National Health Service in the UK. The benefit of using toric IOLs was thus demonstrated, both in standard visual tests and real-world situations. Orientation of toric IOLs during implantation is critical and the benefit of using conjunctival blood vessels for alignment was shown. The issue of centration of IOLs relative to the pupil was also investigated, showing changes with the amount of dilation and repeat dilation evaluation, which must be considered during surgery to optimize the visual performance of premium IOLs. Presbyopia is a global issue, of growing importance as life expectancy increases, with no real long-term cure. Despite enhanced lifestyles, changes in diet and improved medical care, presbyopia still presents in modern life as a significant visual impairment. The onset of presbyopia was found to vary with risk factors including alcohol consumption, smoking, UV exposure and even weight as well as age. A new technique to make measurement of accommodation more objective and robust was explored, although needs for further design modifications were identified. Due to dysphotopsia and lack of intermediate vision through most multifocal IOL designs, the development of a trifocal IOL was shown to minimize these aspects. The current thesis, therefore, emphasises the challenges of premium IOL surgery and need for refinement for optimum visual outcome in addition to outlining how premium IOLs may provide long-term and successful correction of astigmatism and presbyopia.