Network node with wireless and wired interfaces: Nios II processor and uClinux to development of a NCAP embedded (IEEE 1451.1) with two interfaces, wireless (IEEE 1451.5) and wired (IEEE p1451.2)

This paper presents a NCAP embedded on DE2 kit with Nios II processor and uClinux to development of a network gateway with two interfaces, wireless (ZigBee) and wired (RS232) based on IEEE 1451. Both the communications, wireless and wired, were developed to be point-to-point and working with the same protocols, based on IEEE 1451.0-2007. The tests were made using a microcomputer, which through of browser was possible access the web page stored in the DE2 kit and send commands of control and monitoring to both TIMs (WTIM and STIM). The system describes a different form of development of the NCAP node to be applied in different environments with wired or wireless in the same node. © 2011 IEEE.

Development of heterogeneous node network using microcontroller with protocols CAN and Zigbee

In this paper was proposed the development of an heterogeneous system using the microcontroller (AT90CANI28) where the protocol model CAN and the standard IEEE 802.15.4 are connected. This module is able to manage and monitor sensors and actuators using CAN and, through the wireless standard 802.15.4, communicate with the other network modules. © 2011 IEEE.

Using serial bluetooth converters as a sensor link in networked control systems

Networked control systems (NCS) are distributed control system in which sensors, actuators and controllers are physically separated and connected through communication networks. NCS represent the evolution of networked control architectures providing greater modularity and control decentralization, ease maintenance and diagnosis and lower cost of implementation. A recent trend in this research topic is the development of NCS using wireless networks which enable interoperability between existing wired and wireless systems. This paper presents the feasibility analysis of using a serial RS-232 to Bluetooth converter as a wireless sensor link in NCS. In order to support this investigation, relevant performance metrics for wireless control applications such as jitter, time delay and messages lost are highlighted and calculated to evaluate the converter capabilities. In addition the control performance of an implemented motor control system using the converter is analyzed. Experimental results led to the conclusion that serial RS-232 Bluetooth converters can be used to implement wireless networked control systems (WNCS) providing transmission rates and closed control loop times which are acceptable for NCS applications. © 2011 IEEE.

Evaluating serial ZigBee devices for application in wireless networked control systems

Networked control systems (NCS) are distributed control system where the sensors, actuators and controllers are physically separated and connected through communication networks. NCS represent the evolution of networked control architectures providing greater modularity and control decentralization, ease maintenance and diagnosis and lower cost of implementation. A recent trend in this research topic is the development of NCS using wireless networks (WNCS) enabling interoperability between existing wired and wireless systems. This paper evaluates a serial RS-232 ZigBee device as a wireless sensor link in NCS. In order to support this investigation, relevant performance metrics for wireless control applications such as jitter, time delay and messages lost are highlighted and calculated to evaluate the device capabilities. In addition the control performance of an implemented motor control system using the device is analyzed. Experimental results led to the conclusion that serial RS-232 ZigBee devices can be used to implement WNCS and the use of this device delay information in the PID controller discretization can improve the control performance of the system. © 2012 IEEE.

Projeto e implementação de um nodo sensor para aquisição de sinais de extensômetros em redes de sensores sem fio aplicado ao monitoramento de deformações em estruturas

Esta dissertação tem como objetivo principal propor um nodo (ou nó) sensor sem fio para ser utilizado em redes de sensores sem fio, em sistemas de aquisição de dados de extensômetros. O sistema de aquisição para os extensômetros é baseado na ponte de Wheatstone e de modo a permitir várias configurações de extensômetros. O processamento e a comunicação sem fio é realizada pelo ATmega128RFA1, composto por um microcontrolador e um transceiver Rádio-Frequência com o padrão Zigbee. O nodo foi projetado para garantir confiabilidade na aquisição de dados e ser totalmente controlado remotamente. Entre os parâmetros controláveis estão: o ganho do sinal e a taxa de amostragem. Além disso, o nodo possui recursos para efetuar o equilíbrio da ponte de Wheatstone automaticamente. A escolha de seus componentes, baseou-se em critérios relacionados ao consumo de energia do mesmo e ao custo. Foi concebida uma placa de circuito impresso (PCI) para o nodo, e sobre ela foram realizadas estimativas sobre o consumo de energia e valor agregado do protótipo, com o objetivo de analisar a sua viabilidade. Além do projeto do nodo sensor, o trabalho apresenta a proposta de integração do mesmo em uma rede de sensores sem fio (RSSF), incluindo a sugestão do hardware complementar e desenvolvimentos dos softwares. Para os testes do nodo sensor, foi construido experimentalmente um transdutor de força.

Estratégia de redução de consumo de energia em redes de sensores sem fio heterogêneas utilizando lógica fuzzy

O avanço nas áreas de comunicação sem fio e microeletrônica permite o desenvolvimento de equipamentos micro sensores com capacidade de monitorar grandes regiões. Formadas por milhares de nós sensores, trabalhando de forma colaborativa, as Redes de Sensores sem Fio apresentam severas restrições de energia, devido à capacidade limitada das baterias dos nós que compõem a rede. O consumo de energia pode ser minimizado, permitindo que apenas alguns nós especiais, chamados de Cluster Head, sejam responsáveis por receber os dados dos nós que formam seu cluster e propagar estes dados para um ponto de coleta denominado Estação Base. A escolha do Cluster Head ideal influencia no aumento do período de estabilidade da rede, maximizando seu tempo de vida útil. A proposta, apresentada nesta dissertação, utiliza Lógica Fuzzy e algoritmo k-means com base em informações centralizadas na Estação Base para eleição do Cluster Head ideal em Redes de Sensores sem Fio heterogêneas. Os critérios usados para seleção do Cluster Head são baseados na centralidade do nó, nível de energia e proximidade para a Estação Base. Esta dissertação apresenta as desvantagens de utilização de informações locais para eleição do líder do cluster e a importância do tratamento discriminatório sobre as discrepâncias energéticas dos nós que formam a rede. Esta proposta é comparada com os algoritmos Low Energy Adaptative Clustering Hierarchy (LEACH) e Distributed energy-efficient clustering algorithm for heterogeneous Wireless sensor networks (DEEC). Esta comparação é feita, utilizando o final do período de estabilidade, como também, o tempo de vida útil da rede.

Roteamento multicamada baseado em eficiência energética e qualidade de enlace para redes de sensores sem fio

A pesquisa apresentada nesta dissertação descreve a elaboração de um protocolo de roteamento para aplicações de Redes de Sensores Sem Fio (RSSF) em cidade inteligentes com forte restrição de energia e alta densidade de nodos. Através do estudo dos principais objetivos da comunicação de dados e do levantamento do estado-da-arte sobre os protocolos de roteamento e tecnologias para RSSF, a proposta contempla requisitos como: vazão de dados, confiabilidade de entrega e eficiência energética. A pesquisa apresenta em detalhes o protocolo AODV (Ad hoc On Demand Distance Vector), bem como sua relevância no contexto de RSSF devido a sua popularidade entre as plataformas de dispositivos comercializados. Além disso, são apresentados protocolos derivados do AODV, e a ausência de uma proposta robusta capaz de contemplar os requisitos levantados. O protocolo REL (Routing by Energy and Link Quality) é o resultado da pesquisa levantada e a proposta de solução para roteamento plano sob demanda baseado em eficiência energética e qualidade de enlace para prover um roteamento escalável, capaz de realizar balanceamento de carga e prolongar o tempo de vida da rede. O protocolo REL foi avaliado através de simulação e tesbed, a fim de garantir validação da proposta em ambiente real de escala reduzida e simulado de alta densidade. Os resultados mostraram que o protocolo REL apresenta considerável melhoria de entrega de dados através da escolha de enlaces confiáveis de transmissão e menos suscetíveis a erro, além de moderado consumo de energia capaz de prolongar o tempo de vida da rede, evitando a saturação prematura de nodos.

Estudo e simulação de redes de sensores em superfícies não-planas

This Bachelor’s Thesis of Bachelor of Computer Science defines a research and a network sensor simulation on non-planar surfaces . The report is composed of an introduction of the research, a theoretic study, a state of the art and a historic context of sensor network. The simulation consists of the formation of terrain, node’s random distribution and a production and a transmission of the node’s packages. Based on these three important topics , the exchange of information/packages between multiple nodes is through breadth-first search algorithm. The active nodes, node quantity and operation range are also defined in the program. After the program analysis the node activation, the packages are created and transmitted to the next node. This process occurs many times and help on the analysis of the sensor network on non-planar surfaces parameters

Desenvolvimento de um sistema de SHM sem fio e com compensação automática de temperatura

Pós-graduação em Engenharia Elétrica - FEIS

Desenvolvimento de uma rede de sensores sem fio aplicada no monitoramento da variabilidade térmica em casas de vegetação

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Leveraging wireless devices for networked control systems in industrial applications

Networked control systems (NCSs) are distributed control system in which sensors, actuators and controllers are physically separated and connected through communication networks. NCS represent the evolution of networked control architectures providing greater modularity and control decentralization, ease maintenance and diagnosis and lower cost of implementation. A recent trend in this research topic is the development of NCS using wireless networks(WNCS)which enable interoperability between existing wiredand wireless systems. This paper presents the feasibility analysis of using serial to wireless converter as a wireless sensor link in NCS. In order to support this investigation, relevant performance metrics for wireless control applications such as jitter, time delay and messages lost are highlighted and calculated to evaluate the wireless converter capabilities. In addition the control performance of an implemented motor control system using the converter is analyzed. Experimental results led to the conclusion that serial ZigBee device isrecommended against the Bluetooth as it provided better metrics for control applications. However, bothdevices can be used to implement WNCS providing transmission rates and closed control loop times which are acceptable for NCS applications.Moreoverthe use of thewireless device delay in the PID controller discretization can improve the control performance of the system.

Comunicación robusta punto a punto con módulos embebidos de radio frecuencia XBee

Máster Universitario en Sistemas Inteligentes y Aplicaciones Numéricas en Ingeniería (SIANI)

Sistemi riconfigurabili a basso consumo per applicazioni di monitoraggio distribuito

The term Ambient Intelligence (AmI) refers to a vision on the future of the information society where smart, electronic environment are sensitive and responsive to the presence of people and their activities (Context awareness). In an ambient intelligence world, devices work in concert to support people in carrying out their everyday life activities, tasks and rituals in an easy, natural way using information and intelligence that is hidden in the network connecting these devices. This promotes the creation of pervasive environments improving the quality of life of the occupants and enhancing the human experience. AmI stems from the convergence of three key technologies: ubiquitous computing, ubiquitous communication and natural interfaces. Ambient intelligent systems are heterogeneous and require an excellent cooperation between several hardware/software technologies and disciplines, including signal processing, networking and protocols, embedded systems, information management, and distributed algorithms. Since a large amount of fixed and mobile sensors embedded is deployed into the environment, the Wireless Sensor Networks is one of the most relevant enabling technologies for AmI. WSN are complex systems made up of a number of sensor nodes which can be deployed in a target area to sense physical phenomena and communicate with other nodes and base stations. These simple devices typically embed a low power computational unit (microcontrollers, FPGAs etc.), a wireless communication unit, one or more sensors and a some form of energy supply (either batteries or energy scavenger modules). WNS promises of revolutionizing the interactions between the real physical worlds and human beings. Low-cost, low-computational power, low energy consumption and small size are characteristics that must be taken into consideration when designing and dealing with WSNs. To fully exploit the potential of distributed sensing approaches, a set of challengesmust be addressed. Sensor nodes are inherently resource-constrained systems with very low power consumption and small size requirements which enables than to reduce the interference on the physical phenomena sensed and to allow easy and low-cost deployment. They have limited processing speed,storage capacity and communication bandwidth that must be efficiently used to increase the degree of local ”understanding” of the observed phenomena. A particular case of sensor nodes are video sensors. This topic holds strong interest for a wide range of contexts such as military, security, robotics and most recently consumer applications. Vision sensors are extremely effective for medium to long-range sensing because vision provides rich information to human operators. However, image sensors generate a huge amount of data, whichmust be heavily processed before it is transmitted due to the scarce bandwidth capability of radio interfaces. In particular, in video-surveillance, it has been shown that source-side compression is mandatory due to limited bandwidth and delay constraints. Moreover, there is an ample opportunity for performing higher-level processing functions, such as object recognition that has the potential to drastically reduce the required bandwidth (e.g. by transmitting compressed images only when something ‘interesting‘ is detected). The energy cost of image processing must however be carefully minimized. Imaging could play and plays an important role in sensing devices for ambient intelligence. Computer vision can for instance be used for recognising persons and objects and recognising behaviour such as illness and rioting. Having a wireless camera as a camera mote opens the way for distributed scene analysis. More eyes see more than one and a camera system that can observe a scene from multiple directions would be able to overcome occlusion problems and could describe objects in their true 3D appearance. In real-time, these approaches are a recently opened field of research. In this thesis we pay attention to the realities of hardware/software technologies and the design needed to realize systems for distributed monitoring, attempting to propose solutions on open issues and filling the gap between AmI scenarios and hardware reality. The physical implementation of an individual wireless node is constrained by three important metrics which are outlined below. Despite that the design of the sensor network and its sensor nodes is strictly application dependent, a number of constraints should almost always be considered. Among them: • Small form factor to reduce nodes intrusiveness. • Low power consumption to reduce battery size and to extend nodes lifetime. • Low cost for a widespread diffusion. These limitations typically result in the adoption of low power, low cost devices such as low powermicrocontrollers with few kilobytes of RAMand tenth of kilobytes of program memory with whomonly simple data processing algorithms can be implemented. However the overall computational power of the WNS can be very large since the network presents a high degree of parallelism that can be exploited through the adoption of ad-hoc techniques. Furthermore through the fusion of information from the dense mesh of sensors even complex phenomena can be monitored. In this dissertation we present our results in building several AmI applications suitable for a WSN implementation. The work can be divided into two main areas:Low Power Video Sensor Node and Video Processing Alghoritm and Multimodal Surveillance . Low Power Video Sensor Nodes and Video Processing Alghoritms In comparison to scalar sensors, such as temperature, pressure, humidity, velocity, and acceleration sensors, vision sensors generate much higher bandwidth data due to the two-dimensional nature of their pixel array. We have tackled all the constraints listed above and have proposed solutions to overcome the current WSNlimits for Video sensor node. We have designed and developed wireless video sensor nodes focusing on the small size and the flexibility of reuse in different applications. The video nodes target a different design point: the portability (on-board power supply, wireless communication), a scanty power budget (500mW),while still providing a prominent level of intelligence, namely sophisticated classification algorithmand high level of reconfigurability. We developed two different video sensor node: The device architecture of the first one is based on a low-cost low-power FPGA+microcontroller system-on-chip. The second one is based on ARM9 processor. Both systems designed within the above mentioned power envelope could operate in a continuous fashion with Li-Polymer battery pack and solar panel. Novel low power low cost video sensor nodes which, in contrast to sensors that just watch the world, are capable of comprehending the perceived information in order to interpret it locally, are presented. Featuring such intelligence, these nodes would be able to cope with such tasks as recognition of unattended bags in airports, persons carrying potentially dangerous objects, etc.,which normally require a human operator. Vision algorithms for object detection, acquisition like human detection with Support Vector Machine (SVM) classification and abandoned/removed object detection are implemented, described and illustrated on real world data. Multimodal surveillance: In several setup the use of wired video cameras may not be possible. For this reason building an energy efficient wireless vision network for monitoring and surveillance is one of the major efforts in the sensor network community. Energy efficiency for wireless smart camera networks is one of the major efforts in distributed monitoring and surveillance community. For this reason, building an energy efficient wireless vision network for monitoring and surveillance is one of the major efforts in the sensor network community. The Pyroelectric Infra-Red (PIR) sensors have been used to extend the lifetime of a solar-powered video sensor node by providing an energy level dependent trigger to the video camera and the wireless module. Such approach has shown to be able to extend node lifetime and possibly result in continuous operation of the node.Being low-cost, passive (thus low-power) and presenting a limited form factor, PIR sensors are well suited for WSN applications. Moreover techniques to have aggressive power management policies are essential for achieving long-termoperating on standalone distributed cameras needed to improve the power consumption. We have used an adaptive controller like Model Predictive Control (MPC) to help the system to improve the performances outperforming naive power management policies.

Progetto ed implementazione di protocolli a basso consumo energetico per reti wireless

"I computer del nuovo millennio saranno sempre più invisibili, o meglio embedded, incorporati agli oggetti, ai mobili, anche al nostro corpo. L'intelligenza elettronica sviluppata su silicio diventerà sempre più diffusa e ubiqua. Sarà come un'orchestra di oggetti interattivi, non invasivi e dalla presenza discreta, ovunque". [Mark Weiser, 1991] La visione dell'ubiquitous computing, prevista da Weiser, è ormai molto vicina alla realtà e anticipa una rivoluzione tecnologica nella quale l'elaborazione di dati ha assunto un ruolo sempre più dominante nella nostra vita quotidiana. La rivoluzione porta non solo a vedere l'elaborazione di dati come un'operazione che si può compiere attraverso un computer desktop, legato quindi ad una postazione fissa, ma soprattutto a considerare l'uso della tecnologia come qualcosa di necessario in ogni occasione, in ogni luogo e la diffusione della miniaturizzazione dei dispositivi elettronici e delle tecnologie di comunicazione wireless ha contribuito notevolmente alla realizzazione di questo scenario. La possibilità di avere a disposizione nei luoghi più impensabili sistemi elettronici di piccole dimensioni e autoalimentati ha contribuito allo sviluppo di nuove applicazioni, tra le quali troviamo le WSN (Wireless Sensor Network), ovvero reti formate da dispositivi in grado di monitorare qualsiasi grandezza naturale misurabile e inviare i dati verso sistemi in grado di elaborare e immagazzinare le informazioni raccolte. La novità introdotta dalle reti WSN è rappresentata dalla possibilità di effettuare monitoraggi con continuità delle più diverse grandezze fisiche, il che ha consentito a questa nuova tecnologia l'accesso ad un mercato che prevede una vastità di scenari indefinita. Osservazioni estese sia nello spazio che nel tempo possono essere inoltre utili per poter ricavare informazioni sull'andamento di fenomeni naturali che, se monitorati saltuariamente, non fornirebbero alcuna informazione interessante. Tra i casi d'interesse più rilevanti si possono evidenziare: - segnalazione di emergenze (terremoti, inondazioni) - monitoraggio di parametri difficilmente accessibili all'uomo (frane, ghiacciai) - smart cities (analisi e controllo di illuminazione pubblica, traffico, inquinamento, contatori gas e luce) - monitoraggio di parametri utili al miglioramento di attività produttive (agricoltura intelligente, monitoraggio consumi) - sorveglianza (controllo accessi ad aree riservate, rilevamento della presenza dell'uomo) Il vantaggio rappresentato da un basso consumo energetico, e di conseguenza un tempo di vita della rete elevato, ha come controparte il non elevato range di copertura wireless, valutato nell'ordine delle decine di metri secondo lo standard IEEE 802.15.4. Il monitoraggio di un'area di grandi dimensioni richiede quindi la disposizione di nodi intermedi aventi le funzioni di un router, il cui compito sarà quello di inoltrare i dati ricevuti verso il coordinatore della rete. Il tempo di vita dei nodi intermedi è di notevole importanza perché, in caso di spegnimento, parte delle informazioni raccolte non raggiungerebbero il coordinatore e quindi non verrebbero immagazzinate e analizzate dall'uomo o dai sistemi di controllo. Lo scopo di questa trattazione è la creazione di un protocollo di comunicazione che preveda meccanismi di routing orientati alla ricerca del massimo tempo di vita della rete. Nel capitolo 1 vengono introdotte le WSN descrivendo caratteristiche generali, applicazioni, struttura della rete e architettura hardware richiesta. Nel capitolo 2 viene illustrato l'ambiente di sviluppo del progetto, analizzando le piattaforme hardware, firmware e software sulle quali ci appoggeremo per realizzare il progetto. Verranno descritti anche alcuni strumenti utili per effettuare la programmazione e il debug della rete. Nel capitolo 3 si descrivono i requisiti di progetto e si realizza una mappatura dell'architettura finale. Nel capitolo 4 si sviluppa il protocollo di routing, analizzando i consumi e motivando le scelte progettuali. Nel capitolo 5 vengono presentate le interfacce grafiche utilizzate utili per l'analisi dei dati. Nel capitolo 6 vengono esposti i risultati sperimentali dell'implementazione fissando come obiettivo il massimo lifetime della rete.