Determining the interfacial density of states in metal-insulator-semiconductor devices based on poly(3-hexylthiophene)

Low frequency admittance measurements are used to determine the density of interface states in metal-insulator-semiconductor diodes based on the unintentionally doped, p-type semiconductor poly(3-hexylthiophene). After vacuum annealing at 90 degrees C, interface hole trapping states are shown to be distributed in energy with their density decreasing approximately linearly from similar to 20x10(10) to 5x10(10) cm(-2) eV(-1) over an energy range extending from 0.05 to 0.25 eV above the bulk Fermi level. (c) 2008 American Institute of Physics.

Electronic ceramics based on polycrystalline SnO2, TiO2 and (Sn xTi1-x)O2 solid solution

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Qualitative evaluation of active potential barriers in SnO2-based polycrystalline devices by electrostatic force microscopy

This paper discuss the qualitative use of electrostatic force microscopy to study the grain boundary active potential barrier present in dense SnO2-based polycrystalline semiconductors. The effect of heat treatment under rich- and poor-oxygen atmospheres was evaluated while especially considering the number of active barriers at grain boundary regions. The results show that the number of active barriers decrease after heat treatment in an oxygen-poor atmosphere and increase after heat treatment in oxygen-rich atmospheres. The observed effect was explained by considering the presence of oxidized transition metal elements segregated at grain boundary regions which leads to the p-type character of this region, in agreement with the atomic barrier formation mechanism in metal oxide varistor systems.

Crystallographic, dielectric and optical properties of SrBi2Ta2O9 thin films prepared by the polymeric precursor method

Strontium bismuth tantalate thin films were prepared on several substrates (platinized silicon (PvTi/SiO2/Si), n-type (100)-oriented and p-type (111)-oriented silicon wafers, and fused silica) by the solution deposition method. The resin was obtained by the polymeric precursor method, based on the Pechini process, using strontium carbonate, bismuth oxide, and tantalum ethoxide as starting reagents. Characterizations by XRD and SEM were performed for structural and microstructural evaluations. The electrical measurements, carried on the MFM configuration, showed P-r values of 6.24 muC/cm(2) and 31.5 kV/cm for the film annealed at 800 degreesC. The film deposited onto fused silica and treated at 700 degreesC presented around 80 % of transmittance.

Crystallographic, dielectric and optical properties of SrBi 2Ta2O9 thin films prepared by the polymeric precursor method

Strontium bismuth tantalate thin films were prepared on several substrates (platinized silicon (Pt/Ti/SiO 2 /Si), n -type (100)-oriented and p -type (111)-oriented silicon wafers, and fused silica) by the solution deposition method. The resin was obtained by the polymeric precursor method, based on the Pechini process, using strontium carbonate, bismuth oxide, and tantalum ethoxide as starting reagents. Characterizations by XRD and SEM were performed for structural and microstructural evaluations. The electrical measurements, carried on the MFM configuration, showed P r values of 6.24 μC/cm 2 and 31.5 kV/cm for the film annealed at 800 C. The film deposited onto fused silica and treated at 700 C presented around 80% of transmittance. © 2002 Taylor & Francis.

Nitrate Removal on a Cu/Cu2O Photocathode under UV Irradiation and Bias Potential

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The role of hierarchical morphologies in the superior gas sensing performance of CuO-based chemiresistors

The development of gas sensors with innovative designs and advanced functional materials has attracted considerable scientific interest given their potential for addressing important technological challenges. This work presents new insight towards the development of high-performance p-type semiconductor gas sensors. Gas sensor test devices, based on copper (II) oxide (CuO) with innovative and unique designs (urchin-like, fiber-like, and nanorods), are prepared by a microwave-assisted synthesis method. The crystalline composition, surface area, porosity, and morphological characteristics are studied by X-ray powder diffraction, nitrogen adsorption isotherms, field-emission scanning electron microscopy and high-resolution transmission electron microscopy. Gas sensor measurements, performed simultaneously on multiple samples, show that morphology can have a substantial influence on gas sensor performance. An assembly of urchin-like structures is found to be most effective for hydrogen detection in the range of parts-per-million at 200 °C with 300-fold larger response than the previously best reported values for semiconducting CuO hydrogen gas sensors. These results show that morphology plays an important role in the gas sensing performance of CuO and can be effectively applied in the further development of gas sensors based on p-type semiconductors. High-performance gas sensors based on CuO hierarchical morphologies with in situ gas sensor comparison are reported. Urchin-like morphologies with high hydrogen sensitivity and selectivity that show chemical and thermal stability and low temperature operation are analyzed. The role of morphological influences in p-type gas sensor materials is discussed. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Matrizes semicondutoras GaAs e Sn'X IND. 2' dopado com terras-raras Ce ou Eu: investigação do transporte elétrico

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise da estabilidade da região externa do sistema Plutão-Caronte após a descoberta dos novos satélites NIX e HIDRA: aplicação à sonda new horizons

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Construção e caracterização de células solares de filmes finos de CdS e CdTe

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Investigação das características I x V e C x V de NCPS puro, com nitrogênio substitucional carregado (-1 e +1) e com grupos doador (NO2)-aceitador (NH2) através de métodos derivados de hartree-fock

Neste trabalho, fizemos uma investigação sobre o estudo teórico das características I x V e C x V de Nanotubo Carbono de Parede Simples (NCPS) puro, com Nitrogênio substitucional carregado com cargas -1 (caracterizando um indicativo de dopagem tipo n) e +1 (caracterizando um indicativo de dopagem tipo p) e na presença de grupos doador (NO₂)-aceitador (NH₂), através da simulação computacional do estado fundamental de NCPS, bem como de sua estrutura eletrônica e propriedades ópticas, utilizando parametrizações semi-empíricas AM1 (Austin Mudel 1) e ZINDO/S-ClS (Zerner´s lntermediate Neglect of Differential Orbital/Spectroscopic - Cunfiguration lnteraction Single) derivadas da Teoria de Hartree-Fock baseada em técnicas de química quântica. Por meio deste modelo teórico analisamos as propriedades ópticas e eletrônicas, de maior interesse para esses materiais, a fim de se entender a melhor forma de interação desses materiais na fabricação de dispositivos eletrônicos, tais como TECs (Transistores de Efeito de Campo) ou em aplicações em optoeletrônica tais como DEL (Dispositivo Emissor de Luz). Observamos que NCPS com Nitrogênio substitucional apresentam defeitos conformacionais do tipo polarônico. Fizemos as curvas dos espectros UV-visível de Absorção para NCPS armchair e zigzag puro, com Nitrogênio substitucional carregado com cargas (-1 e +1) e na presença de grupos doador (NO₂)-aceitador (NH₂), quando perturbados por intensidades diferentes de campo elétrico. Verificamos que em NCPS zigzag ao aumentarmos a intensidade do campo elétrico, suas curvas sofrem grandes perturbações. Obtivemos as curvas p x E, I x V e C x V para esses NCPS, concluímos que NCPS armchair possui comportamento resistor, pois suas curvas são lineares e zigzag possui comportamento semelhante ao dos dispositivos eletrônicos importantes para o avanço tecnológico. Assim, nossos resultados estão de bom acordo com os resultados experimentais e teóricos de NCPS puro e com Nitrogênio encontrados na literatura.

Analysis of electronic structure of boron nitride nanotubes with different positions of intrinsic impurities

The pristine boron nitride nanotubes have a large direct band gap around 5 eV. This band gap can be engineered by doping. We investigate electronic structure of the doped hexagonal boron nitride (5,5) nanotubes using the linearized augmented cylindrical wave method. In particular, this work focuses on systematical study of the band gap and the density of states around the Fermi-level when the nanotubes are doped by intrinsic impurities of two substitutional boron atoms in a super cell and a comparative analysis of the relative stability of three structures studied here. This corresponds to 3.3% of impurity concentration. We calculate 29 configurations of the nanotubes with different positions of the intrinsic impurities in the nanotube. The band gap and density of states around the Fermi level show strong dependence on the relative positions of the impurity atoms. The two defect sub bands called D^∏(B) appear in the band gap of the pristine nanotube. The doped nanotubes possess p-type semiconductor properties with the band gap of 1.3-1.9 eV.

Propriedades multifuncionais do CaCu3Ti4O12: estudo dos mecanismos e suas aplicações

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Photocatalytic decomposition of rhodamine-B using scandium and silver-modified TiO2 Powders

Semiconductor-mediated photocatalytic oxidation is an interesting method for water decontamination and a specially modified TiO2 is said to be a promising material. This study verified that the synthesis of 1wt%Ag modified-Sc0.01Ti0.99O1.995 powder samples prepared by Polymeric Precursor Method is capable of forming a mixture of anatase-rutile phase with high photocatalytic performance. This kind of material is found to have a lower bandgap compared to the TiO2-anatase commercial powders, which can be associated to an innovative hybrid modification. The simultaneous insertion of scandium in order to generate a p-type semiconductor and a metallic silver nanophase acting as an electron trapper demonstrated being capable of enhancing the degradation of rhodamine B compared to the commercial TiO2. In spite of the different thermal treatments or phase amounts, the hybrid modified powder samples showed higher photocatalytic activity than the commercial ones.

Volcanological aspects of the northwest region of Parana continental flood basalts (Brazil)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)