Guidelines for the Conversion of Urban Four-Lane Undivided Roadways to Three-Lane Two-Way Left-turn Lane Facilities, April 2001

Four-lane undivided roadways in urban areas can experience a degradation of service and/or safety as traffic volumes increase. In fact, the existence of turning vehicles on this type of roadway has a dramatic effect on both of these factors. The solution identified for these problems is typically the addition of a raised median or two-way left-turn lane (TWLTL). The mobility and safety benefits of these actions have been proven and are discussed in the “Past Research” chapter of this report along with some general cross section selection guidelines. The cost and right-of-way impacts of these actions are widely accepted. These guidelines focus on the evaluation and analysis of an alternative to the typical four-lane undivided cross section improvement approach described above. It has been found that the conversion of a four-lane undivided cross section to three lanes (i.e., one lane in each direction and a TWLTL) can improve safety and maintain an acceptable level of service. These guidelines summarize the results of past research in this area (which is almost nonexistent) and qualitative/quantitative before-and-after safety and operational impacts of case study conversions located throughout the United States and Iowa. Past research confirms that this type of conversion is acceptable or feasible in some situations but for the most part fails to specifically identify those situations. In general, the reviewed case study conversions resulted in a reduction of average or 85th percentile speeds (typically less than five miles per hour) and a relatively dramatic reduction in excessive speeding (a 60 to 70 percent reduction in the number of vehicles traveling five miles per hour faster than the posted speed limit was measured in two cases) and total crashes (reductions between 17 to 62 percent were measured). The 13 roadway conversions considered had average daily traffic volumes of 8,400 to 14,000 vehicles per day (vpd) in Iowa and 9,200 to 24,000 vehicles per day elsewhere. In addition to past research and case study results, a simulation sensitivity analysis was completed to investigate and/or confirm the operational impacts of a four-lane undivided to three-lane conversion. First, the advantages and disadvantages of different corridor simulation packages were identified for this type of analysis. Then, the CORridor SIMulation (CORSIM) software was used x to investigate and evaluate several characteristics related to the operational feasibility of a four-lane undivided to three-lane conversion. Simulated speed and level of service results for both cross sections were documented for different total peak-hour traffic, access densities, and access-point left-turn volumes (for a case study corridor defined by the researchers). These analyses assisted with the identification of the considerations for the operational feasibility determination of a four -lane to three-lane conversion. The results of the simulation analyses primarily confirmed the case study impacts. The CORSIM results indicated only a slight decrease in average arterial speed for through vehicles can be expected for a large range of peak-hour volumes, access densities, and access-point left-turn volumes (given the assumptions and design of the corridor case study evaluated). Typically, the reduction in the simulated average arterial speed (which includes both segment and signal delay) was between zero and four miles per hour when a roadway was converted from a four-lane undivided to a three-lane cross section. The simulated arterial level of service for a converted roadway, however, showed a decrease when the bi-directional peak-hour volume was about 1,750 vehicles per hour (or 17,500 vehicles per day if 10 percent of the daily volume is assumed to occur in the peak hour). Past research by others, however, indicates that 12,000 vehicles per day may be the operational capacity (i.e., level of service E) of a three-lane roadway due to vehicle platooning. The simulation results, along with past research and case study results, appear to support following volume-related feasibility suggestions for four-lane undivided to three-lane cross section conversions. It is recommended that a four-lane undivided to three-lane conversion be considered as a feasible (with respect to volume only) option when bi-directional peak-hour volumes are less than 1,500 vehicles per hour, but that some caution begin to be exercised when the roadway has a bi-directional peak-hour volume between 1,500 and 1,750 vehicles per hour. At and above 1,750 vehicles per hour, the simulation indicated a reduction in arterial level of service. Therefore, at least in Iowa, the feasibility of a four-lane undivided to three-lane conversion should be questioned and/or considered much more closely when a roadway has (or is expected to have) a peak-hour volume of more than 1,750 vehicles. Assuming that 10 percent of the daily traffic occurs during the peak-hour, these volume recommendations would correspond to 15,000 and 17,500 vehicles per day, respectively. These suggestions, however, are based on the results from one idealized case xi study corridor analysis. Individual operational analysis and/or simulations should be completed in detail once a four-lane undivided to three-lane cross section conversion is considered feasible (based on the general suggestions above) for a particular corridor. All of the simulations completed as part of this project also incorporated the optimization of signal timing to minimize vehicle delay along the corridor. A number of determination feasibility factors were identified from a review of the past research, before-and-after case study results, and the simulation sensitivity analysis. The existing and expected (i.e., design period) statuses of these factors are described and should be considered. The characteristics of these factors should be compared to each other, the impacts of other potentially feasible cross section improvements, and the goals/objectives of the community. The factors discussed in these guidelines include • roadway function and environment • overall traffic volume and level of service • turning volumes and patterns • frequent-stop and slow-moving vehicles • weaving, speed, and queues • crash type and patterns • pedestrian and bike activity • right-of-way availability, cost, and acquisition impacts • general characteristics, including - parallel roadways - offset minor street intersections - parallel parking - corner radii - at-grade railroad crossings xii The characteristics of these factors are documented in these guidelines, and their relationship to four-lane undivided to three-lane cross section conversion feasibility identified. This information is summarized along with some evaluative questions in this executive summary and Appendix C. In summary, the results of past research, numerous case studies, and the simulation analyses done as part of this project support the conclusion that in certain circumstances a four-lane undivided to three-lane conversion can be a feasible alternative for the mitigation of operational and/or safety concerns. This feasibility, however, must be determined by an evaluation of the factors identified in these guidelines (along with any others that may be relevant for a individual corridor). The expected benefits, costs, and overall impacts of a four-lane undivided to three-lane conversion should then be compared to the impacts of other feasible alternatives (e.g., adding a raised median) at a particular location.

The effect of sodium tetrathionate stabilization on the distribution of three nuclear matrix proteins in human K562 erythroleukemia cells.

Using both conventional fluorescence and confocal laser scanning microscopy we have investigated whether or not stabilization of isolated human erythroleukemic nuclei with sodium tetrathionate can maintain in the nuclear matrix the same spatial distribution of three polypeptides (M(r) 160 kDa and 125 kDa, previously shown to be components of the internal nuclear matrix plus the 180-kDa nucleolar isoform of DNA topoisomerase II) as seen in permeabilized cells. The incubation of isolated nuclei in the presence of 2 mM sodium tetrathionate was performed at 0 degrees C or 37 degrees C. The matrix fraction retained 20-40% of nuclear protein, depending on the temperature at which the chemical stabilization was executed. Western blot analysis revealed that the proteins studied were completely retained in the high-salt resistant matrix. Indirect immunofluorescence experiments showed that the distribution of the three antigens in the final matrix closely resembled that detected in permeabilized cells, particularly when the stabilization was performed at 37 degrees C. This conclusion was also strengthened by analysis of cells, isolated nuclei and the nuclear matrix by means of confocal laser scanning microscopy. We conclude that sodium tetrathionate stabilization of isolated nuclei does not alter the spatial distribution of some nuclear matrix proteins.

Surface deterioration of dental materials after simulated toothbrushing in relation to brushing time and load.

OBJECTIVES: (1) To evaluate the changes in surface roughness and gloss after simulated toothbrushing of 9 composite materials and 2 ceramic materials in relation to brushing time and load in vitro; (2) to assess the relationship between surface gloss and surface roughness. METHODS: Eight flat specimens of composite materials (microfilled: Adoro, Filtek Supreme, Heliomolar; microhybrid: Four Seasons, Tetric EvoCeram; hybrid: Compoglass F, Targis, Tetric Ceram; macrohybrid: Grandio), two ceramic materials (IPS d.SIGN and IPS Empress polished) were fabricated according to the manufacturer's instructions and optimally polished with up to 4000 grit SiC. The specimens were subjected to a toothbrushing (TB) simulation device (Willytec) with rotating movements, toothpaste slurry and at three different loads (100g/250g/350g). At hourly intervals from 1h to 10h TB, mean surface roughness Ra was measured with an optical sensor and the surface gloss (Gl) with a glossmeter. Statistical analysis was performed for log-transformed Ra data applying two-way ANOVA to evaluate the interaction between load and material and load and brushing time. RESULTS: There was a significant interaction between material and load as well as between load and brushing time (p<0.0001). The microhybrid and hybrid materials demonstrated more surface deterioration with higher loads, whereas with the microfilled resins Heliomolar and Adoro it was vice versa. For ceramic materials, no or little deterioration was observed over time and independent of the load. The ceramic materials and 3 of the composite materials (roughness) showed no further deterioration after 5h of toothbrushing. Mean surface gloss was the parameter which discriminated best between the materials, followed by mean surface roughness Ra. There was a strong correlation between surface gloss and surface roughness for all the materials except the ceramics. The evaluation of the deterioration curves of individual specimens revealed a more or less synchronous course suspecting hinting specific external conditions and not showing the true variability in relation to the tested material. SIGNIFICANCE: The surface roughness and gloss of dental materials changes with brushing time and load and thus results in different material rankings. Apart from Grandio, the hybrid composite resins were more prone to surface changes than microfilled composites. The deterioration potential of a composite material can be quickly assessed by measuring surface gloss. For this purpose, a brushing time of 10h (=72,000 strokes) is needed. In further comparative studies, specimens of different materials should be tested in one series to estimate the true variability.

Catalogue of type specimens of the Collection of Invertebrates of Instituto Nacional de Pesquisas da Amazônia, Manaus, Brazil. III. Hexapoda: Isoptera, Mantodea, Mecoptera, Orthoptera, Plecoptera, Trichoptera and Zoraptera

A catalogue of the type specimens of Isoptera, Mantodea, Mecoptera, Orthoptera, Plecoptera, Trichoptera, and Zoraptera deposited in the Invertebrate Collection of the Instituto Nacional de Pesquisas da Amazônia (INPA), Manaus, Brazil, is presented and updated to December, 2007. A total of eight holotypes and seven lots of paratypes of nine species of Isoptera; three holotypes and one paratype of three species of Mantodea; five holotypes and five lots of paratypes of five species of Mecoptera; eight holotypes and five lots of paratypes of eleven species of Orthoptera; three holotypes, three neotypes and two lots of paratypes of seven species of Plecoptera; six holotypes and seven lots of paratypes of ten species of Trichoptera; and two holotypes and three lots of paratypes of three species of Zoraptera, are listed. Specific names are listed alphabetically within the family, followed by bibliographic citation, original genus name, status of type, collection number, locality data and remarks when appropriate.

Comparative phylogeography of mutualists and the effect of the host on the genetic structure of its partners.

Whether or not species participating in specialized and obligate interactions display similar and simultaneous demographic variations at the intraspecific level remains an open question in phylogeography. In the present study, we used the mutualistic nursery pollination occurring between the European globeflower Trollius europaeus and its specialized pollinators in the genus Chiastocheta as a case study. Explicitly, we investigated if the phylogeographies of the pollinating flies are significantly different from the expectation under a scenario of plant-insect congruence. Based on a large-scale sampling, we first used mitochondrial data to infer the phylogeographical histories of each fly species. Then, we defined phylogeographical scenarios of congruence with the plant history, and used maximum likelihood and Bayesian approaches to test for plant-insect phylogeographical congruence for the three Chiastocheta species. We show that the phylogeographical histories of the three fly species differ. Only Chiastocheta lophota and Chiastocheta dentifera display strong spatial genetic structures, which do not appear to be statistically different from those expected under scenarios of phylogeographical congruence with the plant. The results of the present study indicate that the fly species responded in independent and different ways to shared evolutionary forces, displaying varying levels of congruence with the plant genetic structure

Expression of the proto-oncogene c-fos in three-dimensional fetal brain cell cultures and the lack of correlation with maturation-inducing stimuli.

Previous work has shown that aggregating fetal brain cell cultures are able to attain a highly differentiated state, and that their development is greatly enhanced by growth and/or differentiation factors such as epidermal growth factor (EGF), basic fibroblast growth factor (bFGF), and the protein kinase C-activating tumor promoter mezerein. The present study shows that in these 3-dimensional cultures the peptide growth factors EGF and bFGF as well as mezerein are able to induce the expression of the proto-oncogene c-fos. This induction was rapid and transient, in good agreement with observations reported from a wide variety of cell types in vitro. The maximal levels of c-fos mRNA found after stimulation were low in immature cultures and increased greatly as maturation progressed. Of the three factors tested, mezerein was the most potent inducer of c-fos. In contrast to the peptide growth factors EGF and bFGF which were found to induce c-fos only in glial cells, mezerein was stimulatory in glial cells as well as in neurons. A similar cell type specificity has been observed previously for the maturation-enhancing response in immature aggregate cultures. However, in the present study no correlation was found between the degree of c-fos induction and the extent of the maturation-enhancing stimulation. Immature cultures known to be most sensitive and responsive to these maturation-enhancing agents required relatively high doses of peptide growth factors for the induction of c-fos, and the maximal levels of c-fos mRNA elicited were much lower than those in differentiated cultures which did not show any long-term response to these stimuli.(ABSTRACT TRUNCATED AT 250 WORDS)

Kleptoparasitism, disturbance and predation of yellow-legged gulls on Audouin's gulls in three colonies of the western Mediterranean

The impact of yellow-legged gulls on Audouin´s gulls was studied by means of observations from a blind, at the Ebro Delta, the Chafarinas Islands and the Columbretes Islands colonies, during different stages of Audouin´s Gulls breeding cycle. The rates of predation (upon eggs and chicks) and kleptoparasitism (aerial and on courtship and chick-feeding regurgitates) were recorded to evaluate this impact. Kleptoparasitism and predation rates recorded at the three colonies may be considered low when compared with similar studies dealing with other gull species. It seems that interactions did not represent a threat to the population dynamics of Audouin´s Gulls in any of the three colonies. The highest rates of aerial kleptoparasitism, courtship feeding and chick mortality were recorded at the Columbretes Islands, and the lowest at the Ebro Delta. The ratio of the number of yellow-legged gulls to the number of Audouin´s gulls seems to influence the rate of disturbances. Food availability was also likely to play an important role in the number of interactions, which increased when food was in shorter supply. The study at the Ebro Delta and Chafarinas Islands was restricted to some subcolonies and hence results may not be necessarily representative of the entire colonies. The existence of some yellow-legged gull individuals specialised as predators was recorded. Finally, we discuss the suitability of several conservation measures commonly applied in colonies where both species breed syntopically.

Expression analyses of three members of the AtPHO1 family reveal differential interactions between signaling pathways involved in phosphate deficiency and the responses to auxin, cytokinin, and abscisic acid.

The PHO1 protein is involved in loading inorganic phosphate (Pi) to the root xylem. Ten genes homologous to AtPHO1 are present in the Arabidopsis thaliana (L.) Heyn genome. From this gene family, transcript levels of only AtPHO1, AtPHO1;H1 and AtPHO1;H10 were increased by Pi-deficiency. While the up-regulation of AtPHO1;H1 and AtPHO1;H10 by Pi deficiency followed the same rapid kinetics and was dependent on the PHR1 transcription factor, phosphite only strongly suppressed the expression of AtPHO1;H1 and had a minor effect on AtPHO1;H10. Addition of sucrose was found to increase transcript levels of both AtPHO1 and AtPHO1;H1 in Pi-sufficient or Pi-deficient plants, but to suppress AtPHO1:H10 under the same conditions. Treatments of plants with auxin or cytokinin had contrasting effect depending on the gene and on the Pi status of the plants. Thus, while both hormones down-regulated expression of AtPHO1 independently of the plant Pi status, auxin and cytokinin up-regulated AtPHO1;H1 and AtPHO1;H10 expression in Pi-sufficient plants and down-regulated expression in Pi-deficient plants. Treatments with abscisic acid inhibited AtPHO1 and AtPHO1;H1 expression in both Pi-sufficient and Pi-deficient plants, but increased AtPHO1;H10 expression under the same conditions. The inhibition of expression by abscisic acid of AtPHO1 and AtPHO1;H1, and of the Pi-starvation responsive genes AtPHT1;1 and AtIPS1, was dependant on the ABI1 type 2C protein phosphatase. These results reveal that various levels of cross talk between the signal transduction pathways to Pi, sucrose and phytohormones are involved in the regulation of expression of the three AtPHO1 homologues.

Ontogeny and covariation in the Toarcian genus Osperleioceras (Ammonoidea)

Starting from embryonic (protoconch-ammonitella) and early juvenile shells, which are indistinguishable at the species level, growth curves of Osperleioceras from the Reynesi Subzone (Upper Toarcian) of the Causses Basin (Aveyron, France) show a continuous radiating range of correlated variation in dimensional and ornamental characters, such as involution, whorl compression, rib strength and rib density. This covariation pattern can be observed among single-horizon assemblages, as well as during individual ontogenetic development. The existence of a continuous intergradational series of shells, ranging from stout coarsely ribbed to smooth suboxycone morphologies, rules out functional or ecological selectivity to explain this non-random variability pattern. The complex interdependence of shape and sculpture can be simulated by a model in which sculpture intensity depends on mantle curvature [GUEX, 1999]. The expression of covariation in subadult specimens since the base of Upper Toarcian reveals a rise in variability, concomitant with a size decrease, both contemporaneous with environmental instability. It developed in successive bursts from a fairly long low variability period spanning the whole Middle Toarcian.

Generalized Schmidt decomposition and classification of three-quantum-bit states

We prove for any pure three-quantum-bit state the existence of local bases which allow one to build a set of five orthogonal product states in terms of which the state can be written in a unique form. This leads to a canonical form which generalizes the two-quantum-bit Schmidt decomposition. It is uniquely characterized by the five entanglement parameters. It leads to a complete classification of the three-quantum-bit states. It shows that the right outcome of an adequate local measurement always erases all entanglement between the other two parties.

Main-Channel Slopes of Selected Streams in Iowa for Estimation of Flood-Frequency Discharges, November 2004

This report describes a statewide study conducted to develop main-channel slope (MCS) curves for 138 selected streams in Iowa with drainage areas greater than 100 square miles. MCS values determined from the curves can be used in regression equations for estimating flood frequency discharges. Multi-variable regression equations previously developed for two of the three hydrologic regions defined for Iowa require the measurement of MCS. Main-channel slope is a difficult measurement to obtain for large streams using 1:24,000-scale topographic maps. The curves developed in this report provide a simplified method for determining MCS values for sites located along large streams in Iowa within hydrologic Regions 2 and 3. The curves were developed using MCS values quantified for 2,058 selected sites along 138 selected streams in Iowa. A geographic information system (GIS) technique and 1:24,000-scale topographic data were used to quantify MCS values for the stream sites. The sites were selected at about 5-mile intervals along the streams. River miles were quantified for each stream site using a GIS program. Data points for river-mile and MCS values were plotted and a best-fit curve was developed for each stream. An adjustment was applied to all 138 curves to compensate for differences in MCS values between manual measurements and GIS quantification. The multi-variable equations for Regions 2 and 3 were developed using manual measurements of MCS. A comparison of manual measurements and GIS quantification of MCS indicates that manual measurements typically produce greater values of MCS compared to GIS quantification. Median differences between manual measurements and GIS quantification of MCS are 14.8 and 17.7 percent for Regions 2 and 3, respectively. Comparisons of percentage differences between flood-frequency discharges calculated using MCS values of manual measurements and GIS quantification indicate that use of GIS values of MCS for Region 3 substantially underestimate flood discharges. Mean and median percentage differences for 2- to 500-year recurrence-interval flood discharges ranged from 5.0 to 5.3 and 4.3 to 4.5 percent, respectively, for Region 2 and ranged from 18.3 to 27.1 and 12.3 to 17.3 percent for Region 3. The MCS curves developed from GIS quantification were adjusted by 14.8 percent for streams located in Region 2 and by 17.7 percent for streams located in Region 3. Comparisons of percentage differences between flood discharges calculated using MCS values of manual measurements and adjusted-GIS quantification for Regions 2 and 3 indicate that the flood-discharge estimates are comparable. For Region 2, mean percentage differences for 2- to 500-year recurrence-interval flood discharges ranged between 0.6 and 0.8 percent and median differences were 0.0 percent. For Region 3, mean and median differences ranged between 5.4 to 8.4 and 0.0 to 0.3 percent, respectively. A list of selected stream sites presented with each curve provides information about the sites including river miles, drainage areas, the location of U.S. Geological Survey stream flowgage stations, and the location of streams Abstract crossing hydro logic region boundaries or the Des Moines Lobe landforms region boundary. Two examples are presented for determining river-mile and MCS values, and two techniques are presented for computing flood-frequency discharges.

Three-dimensional aspects of fluid flows in channels. II. Effects of meniscus and thin film regimes on viscous fingers

We perform a three-dimensional study of steady state viscous fingers that develop in linear channels. By means of a three-dimensional lattice-Boltzmann scheme that mimics the full macroscopic equations of motion of the fluid momentum and order parameter, we study the effect of the thickness of the channel in two cases. First, for total displacement of the fluids in the channel thickness direction, we find that the steady state finger is effectively two-dimensional and that previous two-dimensional results can be recovered by taking into account the effect of a curved meniscus across the channel thickness as a contribution to surface stresses. Second, when a thin film develops in the channel thickness direction, the finger narrows with increasing channel aspect ratio in agreement with experimental results. The effect of the thin film renders the problem three-dimensional and results deviate from the two-dimensional prediction.

Reliability of methods used for the risk assessment of mixture of micropollutants in aquatic enviromments : from theoretical concepts to field observations

Ces dernières années, de nombreuses recherches ont mis en évidence les effets toxiques des micropolluants organiques pour les espèces de nos lacs et rivières. Cependant, la plupart de ces études se sont focalisées sur la toxicité des substances individuelles, alors que les organismes sont exposés tous les jours à des milliers de substances en mélange. Or les effets de ces cocktails ne sont pas négligeables. Cette thèse de doctorat s'est ainsi intéressée aux modèles permettant de prédire le risque environnemental de ces cocktails pour le milieu aquatique. Le principal objectif a été d'évaluer le risque écologique des mélanges de substances chimiques mesurées dans le Léman, mais aussi d'apporter un regard critique sur les méthodologies utilisées afin de proposer certaines adaptations pour une meilleure estimation du risque. Dans la première partie de ce travail, le risque des mélanges de pesticides et médicaments pour le Rhône et pour le Léman a été établi en utilisant des approches envisagées notamment dans la législation européenne. Il s'agit d'approches de « screening », c'est-à-dire permettant une évaluation générale du risque des mélanges. Une telle approche permet de mettre en évidence les substances les plus problématiques, c'est-à-dire contribuant le plus à la toxicité du mélange. Dans notre cas, il s'agit essentiellement de 4 pesticides. L'étude met également en évidence que toutes les substances, même en trace infime, contribuent à l'effet du mélange. Cette constatation a des implications en terme de gestion de l'environnement. En effet, ceci implique qu'il faut réduire toutes les sources de polluants, et pas seulement les plus problématiques. Mais l'approche proposée présente également un biais important au niveau conceptuel, ce qui rend son utilisation discutable, en dehors d'un screening, et nécessiterait une adaptation au niveau des facteurs de sécurité employés. Dans une deuxième partie, l'étude s'est portée sur l'utilisation des modèles de mélanges dans le calcul de risque environnemental. En effet, les modèles de mélanges ont été développés et validés espèce par espèce, et non pour une évaluation sur l'écosystème en entier. Leur utilisation devrait donc passer par un calcul par espèce, ce qui est rarement fait dû au manque de données écotoxicologiques à disposition. Le but a été donc de comparer, avec des valeurs générées aléatoirement, le calcul de risque effectué selon une méthode rigoureuse, espèce par espèce, avec celui effectué classiquement où les modèles sont appliqués sur l'ensemble de la communauté sans tenir compte des variations inter-espèces. Les résultats sont dans la majorité des cas similaires, ce qui valide l'approche utilisée traditionnellement. En revanche, ce travail a permis de déterminer certains cas où l'application classique peut conduire à une sous- ou sur-estimation du risque. Enfin, une dernière partie de cette thèse s'est intéressée à l'influence que les cocktails de micropolluants ont pu avoir sur les communautés in situ. Pour ce faire, une approche en deux temps a été adoptée. Tout d'abord la toxicité de quatorze herbicides détectés dans le Léman a été déterminée. Sur la période étudiée, de 2004 à 2009, cette toxicité due aux herbicides a diminué, passant de 4% d'espèces affectées à moins de 1%. Ensuite, la question était de savoir si cette diminution de toxicité avait un impact sur le développement de certaines espèces au sein de la communauté des algues. Pour ce faire, l'utilisation statistique a permis d'isoler d'autres facteurs pouvant avoir une influence sur la flore, comme la température de l'eau ou la présence de phosphates, et ainsi de constater quelles espèces se sont révélées avoir été influencées, positivement ou négativement, par la diminution de la toxicité dans le lac au fil du temps. Fait intéressant, une partie d'entre-elles avait déjà montré des comportements similaires dans des études en mésocosmes. En conclusion, ce travail montre qu'il existe des modèles robustes pour prédire le risque des mélanges de micropolluants sur les espèces aquatiques, et qu'ils peuvent être utilisés pour expliquer le rôle des substances dans le fonctionnement des écosystèmes. Toutefois, ces modèles ont bien sûr des limites et des hypothèses sous-jacentes qu'il est important de considérer lors de leur application. - Depuis plusieurs années, les risques que posent les micropolluants organiques pour le milieu aquatique préoccupent grandement les scientifiques ainsi que notre société. En effet, de nombreuses recherches ont mis en évidence les effets toxiques que peuvent avoir ces substances chimiques sur les espèces de nos lacs et rivières, quand elles se retrouvent exposées à des concentrations aiguës ou chroniques. Cependant, la plupart de ces études se sont focalisées sur la toxicité des substances individuelles, c'est à dire considérées séparément. Actuellement, il en est de même dans les procédures de régulation européennes, concernant la partie évaluation du risque pour l'environnement d'une substance. Or, les organismes sont exposés tous les jours à des milliers de substances en mélange, et les effets de ces "cocktails" ne sont pas négligeables. L'évaluation du risque écologique que pose ces mélanges de substances doit donc être abordé par de la manière la plus appropriée et la plus fiable possible. Dans la première partie de cette thèse, nous nous sommes intéressés aux méthodes actuellement envisagées à être intégrées dans les législations européennes pour l'évaluation du risque des mélanges pour le milieu aquatique. Ces méthodes sont basées sur le modèle d'addition des concentrations, avec l'utilisation des valeurs de concentrations des substances estimées sans effet dans le milieu (PNEC), ou à partir des valeurs des concentrations d'effet (CE50) sur certaines espèces d'un niveau trophique avec la prise en compte de facteurs de sécurité. Nous avons appliqué ces méthodes à deux cas spécifiques, le lac Léman et le Rhône situés en Suisse, et discuté les résultats de ces applications. Ces premières étapes d'évaluation ont montré que le risque des mélanges pour ces cas d'étude atteint rapidement une valeur au dessus d'un seuil critique. Cette valeur atteinte est généralement due à deux ou trois substances principales. Les procédures proposées permettent donc d'identifier les substances les plus problématiques pour lesquelles des mesures de gestion, telles que la réduction de leur entrée dans le milieu aquatique, devraient être envisagées. Cependant, nous avons également constaté que le niveau de risque associé à ces mélanges de substances n'est pas négligeable, même sans tenir compte de ces substances principales. En effet, l'accumulation des substances, même en traces infimes, atteint un seuil critique, ce qui devient plus difficile en terme de gestion du risque. En outre, nous avons souligné un manque de fiabilité dans ces procédures, qui peuvent conduire à des résultats contradictoires en terme de risque. Ceci est lié à l'incompatibilité des facteurs de sécurité utilisés dans les différentes méthodes. Dans la deuxième partie de la thèse, nous avons étudié la fiabilité de méthodes plus avancées dans la prédiction de l'effet des mélanges pour les communautés évoluant dans le système aquatique. Ces méthodes reposent sur le modèle d'addition des concentrations (CA) ou d'addition des réponses (RA) appliqués sur les courbes de distribution de la sensibilité des espèces (SSD) aux substances. En effet, les modèles de mélanges ont été développés et validés pour être appliqués espèce par espèce, et non pas sur plusieurs espèces agrégées simultanément dans les courbes SSD. Nous avons ainsi proposé une procédure plus rigoureuse, pour l'évaluation du risque d'un mélange, qui serait d'appliquer d'abord les modèles CA ou RA à chaque espèce séparément, et, dans une deuxième étape, combiner les résultats afin d'établir une courbe SSD du mélange. Malheureusement, cette méthode n'est pas applicable dans la plupart des cas, car elle nécessite trop de données généralement indisponibles. Par conséquent, nous avons comparé, avec des valeurs générées aléatoirement, le calcul de risque effectué selon cette méthode plus rigoureuse, avec celle effectuée traditionnellement, afin de caractériser la robustesse de cette approche qui consiste à appliquer les modèles de mélange sur les courbes SSD. Nos résultats ont montré que l'utilisation de CA directement sur les SSDs peut conduire à une sous-estimation de la concentration du mélange affectant 5 % ou 50% des espèces, en particulier lorsque les substances présentent un grand écart- type dans leur distribution de la sensibilité des espèces. L'application du modèle RA peut quant à lui conduire à une sur- ou sous-estimations, principalement en fonction de la pente des courbes dose- réponse de chaque espèce composant les SSDs. La sous-estimation avec RA devient potentiellement importante lorsque le rapport entre la EC50 et la EC10 de la courbe dose-réponse des espèces est plus petit que 100. Toutefois, la plupart des substances, selon des cas réels, présentent des données d' écotoxicité qui font que le risque du mélange calculé par la méthode des modèles appliqués directement sur les SSDs reste cohérent et surestimerait plutôt légèrement le risque. Ces résultats valident ainsi l'approche utilisée traditionnellement. Néanmoins, il faut garder à l'esprit cette source d'erreur lorsqu'on procède à une évaluation du risque d'un mélange avec cette méthode traditionnelle, en particulier quand les SSD présentent une distribution des données en dehors des limites déterminées dans cette étude. Enfin, dans la dernière partie de cette thèse, nous avons confronté des prédictions de l'effet de mélange avec des changements biologiques observés dans l'environnement. Dans cette étude, nous avons utilisé des données venant d'un suivi à long terme d'un grand lac européen, le lac Léman, ce qui offrait la possibilité d'évaluer dans quelle mesure la prédiction de la toxicité des mélanges d'herbicide expliquait les changements dans la composition de la communauté phytoplanctonique. Ceci à côté d'autres paramètres classiques de limnologie tels que les nutriments. Pour atteindre cet objectif, nous avons déterminé la toxicité des mélanges sur plusieurs années de 14 herbicides régulièrement détectés dans le lac, en utilisant les modèles CA et RA avec les courbes de distribution de la sensibilité des espèces. Un gradient temporel de toxicité décroissant a pu être constaté de 2004 à 2009. Une analyse de redondance et de redondance partielle, a montré que ce gradient explique une partie significative de la variation de la composition de la communauté phytoplanctonique, même après avoir enlevé l'effet de toutes les autres co-variables. De plus, certaines espèces révélées pour avoir été influencées, positivement ou négativement, par la diminution de la toxicité dans le lac au fil du temps, ont montré des comportements similaires dans des études en mésocosmes. On peut en conclure que la toxicité du mélange herbicide est l'un des paramètres clés pour expliquer les changements de phytoplancton dans le lac Léman. En conclusion, il existe diverses méthodes pour prédire le risque des mélanges de micropolluants sur les espèces aquatiques et celui-ci peut jouer un rôle dans le fonctionnement des écosystèmes. Toutefois, ces modèles ont bien sûr des limites et des hypothèses sous-jacentes qu'il est important de considérer lors de leur application, avant d'utiliser leurs résultats pour la gestion des risques environnementaux. - For several years now, the scientists as well as the society is concerned by the aquatic risk organic micropollutants may pose. Indeed, several researches have shown the toxic effects these substances may induce on organisms living in our lakes or rivers, especially when they are exposed to acute or chronic concentrations. However, most of the studies focused on the toxicity of single compounds, i.e. considered individually. The same also goes in the current European regulations concerning the risk assessment procedures for the environment of these substances. But aquatic organisms are typically exposed every day simultaneously to thousands of organic compounds. The toxic effects resulting of these "cocktails" cannot be neglected. The ecological risk assessment of mixtures of such compounds has therefore to be addressed by scientists in the most reliable and appropriate way. In the first part of this thesis, the procedures currently envisioned for the aquatic mixture risk assessment in European legislations are described. These methodologies are based on the mixture model of concentration addition and the use of the predicted no effect concentrations (PNEC) or effect concentrations (EC50) with assessment factors. These principal approaches were applied to two specific case studies, Lake Geneva and the River Rhône in Switzerland, including a discussion of the outcomes of such applications. These first level assessments showed that the mixture risks for these studied cases exceeded rapidly the critical value. This exceeding is generally due to two or three main substances. The proposed procedures allow therefore the identification of the most problematic substances for which management measures, such as a reduction of the entrance to the aquatic environment, should be envisioned. However, it was also showed that the risk levels associated with mixtures of compounds are not negligible, even without considering these main substances. Indeed, it is the sum of the substances that is problematic, which is more challenging in term of risk management. Moreover, a lack of reliability in the procedures was highlighted, which can lead to contradictory results in terms of risk. This result is linked to the inconsistency in the assessment factors applied in the different methods. In the second part of the thesis, the reliability of the more advanced procedures to predict the mixture effect to communities in the aquatic system were investigated. These established methodologies combine the model of concentration addition (CA) or response addition (RA) with species sensitivity distribution curves (SSD). Indeed, the mixture effect predictions were shown to be consistent only when the mixture models are applied on a single species, and not on several species simultaneously aggregated to SSDs. Hence, A more stringent procedure for mixture risk assessment is proposed, that would be to apply first the CA or RA models to each species separately and, in a second step, to combine the results to build an SSD for a mixture. Unfortunately, this methodology is not applicable in most cases, because it requires large data sets usually not available. Therefore, the differences between the two methodologies were studied with datasets created artificially to characterize the robustness of the traditional approach applying models on species sensitivity distribution. The results showed that the use of CA on SSD directly might lead to underestimations of the mixture concentration affecting 5% or 50% of species, especially when substances present a large standard deviation of the distribution from the sensitivity of the species. The application of RA can lead to over- or underestimates, depending mainly on the slope of the dose-response curves of the individual species. The potential underestimation with RA becomes important when the ratio between the EC50 and the EC10 for the dose-response curve of the species composing the SSD are smaller than 100. However, considering common real cases of ecotoxicity data for substances, the mixture risk calculated by the methodology applying mixture models directly on SSDs remains consistent and would rather slightly overestimate the risk. These results can be used as a theoretical validation of the currently applied methodology. Nevertheless, when assessing the risk of mixtures, one has to keep in mind this source of error with this classical methodology, especially when SSDs present a distribution of the data outside the range determined in this study Finally, in the last part of this thesis, we confronted the mixture effect predictions with biological changes observed in the environment. In this study, long-term monitoring of a European great lake, Lake Geneva, provides the opportunity to assess to what extent the predicted toxicity of herbicide mixtures explains the changes in the composition of the phytoplankton community next to other classical limnology parameters such as nutrients. To reach this goal, the gradient of the mixture toxicity of 14 herbicides regularly detected in the lake was calculated, using concentration addition and response addition models. A decreasing temporal gradient of toxicity was observed from 2004 to 2009. Redundancy analysis and partial redundancy analysis showed that this gradient explains a significant portion of the variation in phytoplankton community composition, even when having removed the effect of all other co-variables. Moreover, some species that were revealed to be influenced positively or negatively, by the decrease of toxicity in the lake over time, showed similar behaviors in mesocosms studies. It could be concluded that the herbicide mixture toxicity is one of the key parameters to explain phytoplankton changes in Lake Geneva. To conclude, different methods exist to predict the risk of mixture in the ecosystems. But their reliability varies depending on the underlying hypotheses. One should therefore carefully consider these hypotheses, as well as the limits of the approaches, before using the results for environmental risk management

Three-dimensional aspects of fluid flows in channels. II. Effects of meniscus and thin film regimes on viscous fingers

We perform a three-dimensional study of steady state viscous fingers that develop in linear channels. By means of a three-dimensional lattice-Boltzmann scheme that mimics the full macroscopic equations of motion of the fluid momentum and order parameter, we study the effect of the thickness of the channel in two cases. First, for total displacement of the fluids in the channel thickness direction, we find that the steady state finger is effectively two-dimensional and that previous two-dimensional results can be recovered by taking into account the effect of a curved meniscus across the channel thickness as a contribution to surface stresses. Second, when a thin film develops in the channel thickness direction, the finger narrows with increasing channel aspect ratio in agreement with experimental results. The effect of the thin film renders the problem three-dimensional and results deviate from the two-dimensional prediction.

Phytochemical investigation of alpine plants : the cottonsedges Eriophorum scheuchzeri Hoppe, E. angustifolium Honck. and E. latifolium Hoppe (CYPERACEAE)

Résumé: Alpine plants living at high altitudes undergo a series of climatic stress factors (chilling, enhanced UV radiation, short growing season, low nutriment supply...) which may influence their secondary compounds composition. Many publications showed in these last years that plants under stress conditions do synthesize a range of specific defence compounds (terpenes, flavonoids, coumarines...). A careful phytochemical investigation of those plants could therefore lead to the discovery of active molecules. Thus, for the biological and chemical screening, about 30 alpine plants have been collected above 2000 metres, in the alpine grass-lands. Eriophorum scheuchzeri Hoppe (Cyperaceae), not yet investigated phytochemically, revealed in its lipophilic and polar extracts the presence of various radical scavengers in a TLC autography with the DPPH (2,2-dipheny1-1- picrylhydrazyl) radical as spray reagent, as well as several antifungal compounds acitve against Cladosporium cucumerinum and Candida albi cans. The first part of this study consisted in the detection, isolation and characterization of the bioactive natural compounds present in the lipophilic extract of Eriophorum scheuchzeri. Among the eight isolated compounds, six were isoflavones. No isoflavones have been reported in the Cyperaceae family yet, nor in related families such as Poaceae or Juncaceae. Besides, isoflavones are generally rare in the plant kingdom and and they occur only in some families, such as Fabaceae, Rosaceae or Myristicaceae. In addition, out of these six isoflavones, three were new isoflavones. The known compounds were parvisoflavone A and B and cajanin which are already known isoflavones in the Fabaceae family. Two of the new isoflavones were particular, as they were C-methylated on the B-ring at the C-3' position. Methylated flavonoids are particularly rare in the plant kingdom. At present, no C-methylated isoflavones with methyl groups on the B-ring have ever been reported. The fourth new compound was a prenylated flavanone. Flavanones are also rare in the Cyperaceae family since they were found only in two genera (Cyperus and Schoenus). Finally, the widespread flavone tricin, characteristic of the Cyperaceae and Poaceae family has also been isolated. The second part of this study consisted in the characterization of the polar components present in the Me0H extract. In order to obtain mass and UV information about the secondary compounds present in the Eriophorum scheuchzeri methanolic extract, a LC-UV/DAD-APCl/MSn analysis has been performed as a first dereplication step. The UV/DAD spectra showed the presence of polyphenol compounds (phenylpropanoids and flavonoids). The LC-APCI/MSn analysis allowed the determination of the molecular weight of these compounds. Moreover, the fragmentation pattern of the [M+H]+ ions indicated presence of mono-, di- and tri-glycosides. LC-UV in combination with UV shift reagents added post-column was used in a second phase for the structural elucidation of the flavonoids. It allowed the positioning of the sugars on the aglycones. Finally, LC-NMR was used for a more detailed structural investigation of the compounds present in the crude MEOH extract. Thus, 10 fiavonoids have been totally or partially characterized by LC-UV-MS and LC-1H-RMN and UV-shift reagents added post column. However, the information obtained on-line was not always sufficient to allow a complete identification of all the compounds. Some of these compounds especially those with more than two sugar units attached to them, have been isolated in order to proceed to their complete characterization. Moreover, the Eriophorum scheuchzeri species was compared to two other species from the same genus. A LC-UV-ESI/MS analysis enabled a survey of the chemical composition of the DCM extracts of two related species E. angustifolium (Honck) and E. latifolium (Hoppe). The chromatograms of the three species showed some similarities in their flavonoid contents, especially by the recurrent presence of three compounds. The MEOH extracts of all three species have been compared by means of LC-UV-APCl/MS analyses. The chromatographic profile of all the three species showed even closer similarities than those found in the DCM extracts. E. angustifolium Honck. and E. latifolium species showed 7 compounds in common. Finally, the pure compounds obtained from the DCM (CH2Cl2) fraction were tested at different concentration, in order to evaluate their chemical and biological activities. All eight compounds showed an anti-scavenger activity against the DPPH radical, and four compounds showed antifungal activities against Cladosporium cucumerinum and Candida albicans. The pure compounds isolated from the MeOH extract were tested only for their biological activities as their antioxidant activity is already well documented in the literature. No compound showed a biological activity against Cladosporium cucumerinum and Candida albicans. Résumé: De nombreux travaux ont démontré ces dernières décennies que les plantes soumises à différents types de stress (basse température, UV, stress hydrique) synthétisent des composés secondaires (fiavonoides, coumarines, terpènes...) de protection et de défense. Les plantes d'altitude par exemple qui sont exposées à des conditions climatiques et environnementales difficiles, ont tendance à synthétiser des substances antioxydantes et antiradicalaires. Une investigation phytochirnique de ces plantes a conduit à la découverte de nouvelles molécules actives. Ainsi plusieurs plantes alpines ont été sélectionnées en fonction de leur habitat en vue de les soumettre aux tests biologiques (antifongiques) et chimiques (antiradicalaires) menés en routine dans notre laboratoire. Dans ce criblage biologique préliminaire, les extraits d'Eriophorum scheuchzeri Hoppe (Cyperaceae) ont réagi positivement aux différents tests. Il a donc été décidé d'entreprendre l'isolement des composés actifs. La première partie de ce travail a consisté à détecter, isoler et caractériser les composés naturels actifs présents dans l'extrait apolaire d' Eriophorum scheuchzeri. Parmi les huit composés isolés, quatre d'entre eux sont nouveaux. Un de ces produits est une flavanone et trois sont de nouvelles isoflavones, particulièrement intéressantes car elles possèdent des groupements C-méthylés au niveau du cycle B. Les flavonoides C-méthylés sont peu répandus dans le règne végétal et les rares exemples connus sont généralement C-méthylés sur le cycle A. Les quatre autres composés isolés n'ont jamais été décrits dans cette famille. Il s'agit d' isoflavones, les parvisoflavones A et B et la cajanine. Enfin, la flavone tricine, flavonoide caractéristique des Cyperaceae et des Poaceae a également été isolée. La deuxième partie de ce travail a consisté à caractériser les constituants polaires présents dans l'extrait methanolique. L'extrait a été analysé par chromatographie analytique couplée à différentes méthodes spectroscopiques (LC-UV-MS et LC-UV-1H RMN). De cette façon, douze flavonoides et un dérivé du phénylpropane, l'acide chlorogénique ont été identifiés. Les flavonoides tri-glycosylés ont dû être isolés afin de déterminer la nature et l'enchaînement des sucres. Finalement, l'espèce Eriophorum scheuchzeri a été comparée à deux autres espèces d' Eriophorum, soit E. angustifolium et E. latifolium. En conclusion, cette étude phytochimique a abouti à l'isolement de plusieurs nouvelles isoflavones aux activités antioxydantes et antifongiques ainsi qu'oestrogéniques.