Wear of hardfacing white cast irons by solid particle erosion

The response of three commercial weld-hardfacing alloys to erosive wear has been studied. These were high chromium white cast irons, deposited by an open-arc welding process, widely used in the mineral processing and steelmaking industries for wear protection. Erosion tests were carried out with quartz sand, silicon carbide grit and blast furnace sinter of two different sizes, at a velocity of 40 m s-1 and at impact angles in the range 20° to 90°. A monolithic white cast iron and mild steel were also tested for comparison. Little differences were found in the wear rates when silica sand or silicon carbide grit was used as the erodent. Significant differences were found, however, in the rankings of the materials. Susceptibility to fracture of the carbide particles in the white cast irons played an important role in the behaviour of the white cast irons. Sinter particles were unable to cause gross fracture of the carbides and so those materials with a high volume fraction of carbides showed the greatest resistance to erosive wear. Silica and silicon carbide were capable of causing fracture of the primary carbides. Concentration of plastic strain in the matrix then led to a high wear rate for the matrix. At normal impact with silica or silicon carbide erodents mild steel showed a greater resistance to erosive wear than these alloys. © 1995.

National Agricultural Research Organisation. Fisheries Resources Research Institute Annual Report 1999/2000

Lake Victoria shoreline in Jinja Municipality has four urban wetlands of Kirinya West/Loco, Kirinya East/Walukuba, Masese and Budumbuli which have undergone major changes during the past fifty years due to increased human activities. Amongst these activities is the continuous inflow of agricultural run-off, industrial and municipal wastewater. A significant increase in nutrient loads of Nitrogen and Phosphorus from the catchment area continues to enhance eutrophication of Lake Victoria. Pollution from point sources (Industrial plants and NWSC Kirinya final maturation pond) into Jinja’s urban wetlands were therefore studied using a simplified material flux analysis methodology to identify the active elements and estimate the pollution loads due to Nitrogen, Phosphorus, Carbon (nutrients), Chromium, Copper, Lead, Nickel and Manganese metals.

Biodiversity and production of bioactive material from cyanobacteria in Persian Gulf

In this project sampling was done from 9 stations in 3 depths during 5 seasons to separate, identify and examine the biodiversity of cyanobacteria. Another sampling also has been done to analyse all physical and physicochemical parameters, primary production and polluting agents such as heavy metals and oil hydrocarbons in water and sediments. Along with optimization of Oscillatoria to study the ability of producing natural substances, these cyanobacteria were analysed from the point of antimicrobial and mutagenic effects. To examine the relationships among analysed parameters, the regression test, analysis of varian and Post Hoc were used. As the result of this study 48 genus of cyanobacteria were pecognised among which 35.5% were croco ccales and 64.4% were Hermogonals. Oscillatoria was one of the Filamentous cyanobacteria which had antibacterial and mutagenic effects. The results of multicommunity consistency varians test, post Hoc and homogenous subsets show significant difference between biodiversity of cyanotbacteria in coral ecosystem, Mangrove and transite. The linear correlation coefficient between biodiversity of cyanobacteria and bioenvironmental agents were examined, but there was no continuous relation between these factors and biological biodiversity. In Surface layer there was a significant correlation coefficent at 0.048 and probability at 95% confidence interval. Also, the biodiversity is depended on oil pollution and heavy metals such as copper (Cu) and chromium (Cr).

Fabrication of high-Q film bulk acoustic resonator (FBAR) filters withcarbon nanotube (CNT) electrodes

FBAR devices with carbon nanotube (CNT) electrodes have been developed withthe aim of taking advantage of the low density and high acoustic impedance ofthe CNTs compared to other known materials. The influence of the CNTs on thefrequency response of the FBAR devices was studied by comparing two identicalsets of devices, one set comprised FBARs fabricated with chromium/gold bilayerelectrodes, and the second set comprised FBARs fabricated with CNT electrodes.It was found that the CNTs had a significant effect on attenuating travellingwaves at the surface of the FBARs membranes due to their high elastic stiffness.Finite element analysis of the devices fabricated was carried out using COMSOLMultiphysics, and the numerical results confirmed the experimental resultsobtained. © 2010 IEEE.

ZnO-Based FBAR resonators with carbon nanotube electrodes

Film bulk acoustic resonator (FBAR) devices with carbon nanotube (CNT) electrodes directly grown on a ZnO film by thermal chemical vapor deposition have been fabricated. CNT electrodes possess a very low density and high acoustic impedance, which reduces the intrinsic mass loading effect resulting from the electrodes' weight and better confines the longitudinal acoustic standing waves inside the resonator, in turn providing a resonator with a higher quality factor. The influence of the CNTs on the frequency response of the FBAR devices was studied by comparing two identical sets of devices; one set comprised FBARs fabricated with chromium/ gold bilayer electrodes, and the second set comprised FBARs fabricated with CNT electrodes. It was found that the CNTs had a significant effect on attenuating traveling waves at the surface of the FBARs' membranes because of their high elastic stiffness. Three-dimensional finite element analysis of the devices fabricated was carried out, and the numerical simulations were consistent with the experimental results obtained. © 2011 IEEE.

The distribution and concentration levels of trace metals in water and sediments of Lake Victoria, Kenya

The water and bottom sediments of Lake Victoria (Kenya) were analysed for A1, Fe, Mn, Zn, Pb, Cu, Cr and Cd. The total metal concentrations were determined and their mean variations and distributions discussed. The bottom lake waters showed higher concentration levels than the surface waters. The range of values (in mg/l) in the bottom and surface lake waters were as follows: Surface Waters: A1(0.08 - 3.98), Fe(0.09 - 4.01), Mn(0.02 - 0.10). Zn(0.01 -0.07), Pb(0.001- 0.007), Cu(not detected - 0.006), Cr(not detected - 0.004). Bottom Waters: A1(0.1 0 - 6.59), Fe(0.23 - 9.64), Mn(0.04 - 0.39), Zn(0.01- 0.08), Pb(0.002 - 0.009), Cu(not detected - 0.03). Cr(not detected -0.002). River mouths and shallow areas in the lake showed higher total metal concentrations than offshore deeper areas. Apart from natural metal levels, varied urban activities and wastes greatly contribute to the lake metal pollution as shown by high Pb and Zn levels in sediments, around Kisumu and Homa Bay areas. Other comparatively high values and variations could be attributed to the varied geological characteristics of the lake and its sediments. Compared to the established W.H.O (1984) drinking water standards manganese, aluminium and iron levels were above these limits whereas zinc, lead, chromium, copper and cadmium were below.

Microcalorimetric investigation of the toxic action of Cr(VI) on the metabolism of Tetrahymena thermophila BF5 during growth

Tetrahymena thermophila BF5 produce heat by metabolism and movement. Using a TAM air isothermal microcalorimeter, the power-time curves of the metabolism of T thermophila BF5 during growth were obtained and the action on them by the addition of Cr(VI) were studied. The morphological change with Cr(VI) coexisted and biomass change during the process of T thermophila BF5 growth were studied by light microscope. Chromium has been regarded as an essential trace element for life. However, hexavalent chromium is a known carcinogen, mutagen, cytotoxicant and strong oxidizing agent. Cr(VI) of different concentration have different effects on T thermophila BF5 growth with the phenomenon of low dose stimulation (0-3 x 10(-5) mol L-1) and high dose inhibition (3 x 10(-5) to 2.4 x 10(-4) mol L-1). The relationship between the growth rate constant (k) and c is a typical U-shaped curve, which is a characteristic of hormesis. T thermophila BF5 cannot grow at all when the concentration of Cr(VI) is up to 2.4 x 10(-4) mol L-1. The microscopic observations agree well with the results obtained by means of microcalorimetry. And T thermophila BF5 had obviously morphological changes by the addition of Cr(VI). (c) 2006 Elsevier B.V. All rights reserved.

Nitrogen defects and ferromagnetism in Cr-doped dilute magnetic semiconductor AlN from first principles

High Curie temperature of 900 K has been reported in Cr-doped AlN diluted magnetic semiconductors prepared by various methods, which is exciting for spintronic applications. It is believed that N defects play important roles in achieving the high-temperature ferromagnetism in good samples. Motivated by these experimental advances, we use a full-potential density-functional-theory method and supercell approach to investigate N defects and their effects on ferromagnetism of (Al,Cr)N with N vacancies (V-N). We investigate the structural and electronic properties of V-N, single Cr atom, Cr-Cr atom pairs, Cr-V-N pairs, and so on. In each case, the most stable structure is obtained by comparing different atomic configurations optimized in terms of the total energy and the force on every atom, and then it is used to calculate the defect formation energy and study the electronic structures. Our total-energy calculations show that the nearest substitutional Cr-Cr pair with the two spins in parallel is the most favorable and the nearest Cr-V-N pair makes a stable complex. Our formation energies indicate that V-N regions can be formed spontaneously under N-poor condition because the minimal V-N formation energy equals -0.23 eV or Cr-doped regions with high enough concentrations can be formed under N-rich condition because the Cr formation energy equals 0.04 eV, and hence real Cr-doped AlN samples are formed by forming some Cr-doped regions and separated V-N regions and through subsequent atomic relaxation during annealing. Both of the single Cr atom and the N vacancy create filled electronic states in the semiconductor gap of AlN. N vacancies enhance the ferromagnetism by adding mu(B) to the Cr moment each but reduce the ferromagnetic exchange constants between the spins in the nearest Cr-Cr pairs. These calculated results are in agreement with experimental observations and facts of real Cr-doped AlN samples and their synthesis. Our first-principles results are useful to elucidate the mechanism for the ferromagnetism and to explore high-performance Cr-doped AlN diluted magnetic semiconductors.

Stress corrosion studies of ion implanted austenitic steel

Stress corrosion studies of 50 Mn18Cr4 austenitic steel implanted with 120 keV N+, 100 keV Cr+, 200 keV and 400 keV Er+ ions were carried out by constant strain method in the nitrate solution. Surface composition and depth profiles of the implanted material were measured by AES sputter etching technique. The results exhibit that nitrogen implantation has no significant affection to the stress corrosion, but the chromium and erbium implantation has prolonged the incubation period of the stress corrosion cracking. (C) 1999 Kluwer Academic Publishers.

铬污染土壤修复过程中土壤细菌群落多样性的RFLP分析

对污染土壤修复过程中土壤细菌群落多样性的变化进行研究。【方法】以淹水培养后的模拟铬污染土壤为供试材料,通过直接提取土壤中总细菌DNA,利用细菌专一引物克隆细菌16S rDNA片段,分别建立克隆文库。利用PCR-RFLP技术,分析比较了土壤淹水10 d(对照,S1)、添加Cr(Ⅵ)淹水10 d(S2)、添加Cr(Ⅵ)和Fe(OH)3淹水10 d(S3)及20 d(S4)4个处理中土壤细菌群落的变化。【结果】用专一引物克隆细菌16S rDNA片段,分别建立了克隆文库;用限制性内切酶RsaⅠ进行细菌16S rDNA PCR-RFLP分析,分别得到123,120,97和69个酶切类型,库容值分别为54.92%,55.43%,65.33%和76.60%;Shannon-Wiener指数、Gini指数、物种丰富度指数(dMa)和物种均匀度指数(Jgi)均表现为S1>S2>S3>S4,以上4个指数的变异系数分别为11.51%,1.84%,23.64%和1.55%;基于细菌多样性参数的聚类分析结果,将对照S1和添加Cr(Ⅵ)处理的S2归于一类,而2个添加Fe处理的土壤S3和S4聚为一类。【结论】经过10 d淹水处理,...

铬系催化剂聚合1,3-双烯烃的研究

铬系催化剂是合成1,2-聚丁二烯和3,4-聚异戊二烯的一种主要催化剂体系，1,2-聚丁二烯和3,4-聚异戊二烯是制造高性能轮胎的重要原料。本论文研究了以含氮化合物和含磷化合物为配体的铬催化剂合成1,2-聚丁二烯和3,4-聚异戊二烯的反应规律。 1. 以邻菲咯啉为配体的铬催化剂在己烷中50℃下可获得1,2-结构、顺-1,4-结构和反-1,4-结构单元含量分别约为50%、30%和20%，分子量呈双峰分布的聚丁二烯。改变聚合温度，可有效控制聚合物的1,2-结构含量和分子量及分布。催化剂通过预陈化方式，可有效抑制低聚物的生成。 2. 以亚磷酸二烷基酯为配体的铬催化剂是合成1,2-聚丁二烯的高效催化剂，所得聚合物具有高的1,2-结构含量（> 78%）。改变烷基铝和亚磷酸二烷基酯的结构，可以得到高熔点或低熔点间同1,2-聚丁二烯和无规1,2-聚丁二烯。催化剂以现配方式的活性最高。 3. 以磷酸三苯酯为配体的铬催化剂可获得间同1,2-聚丁二烯，而聚合物中含有低聚物。催化剂以现配方式的活性最高。聚合物的熔点，低聚物的含量与磷酸三苯酯的结构有一定的关系。 4. 以邻菲咯啉为配体的铬催化剂在50℃下聚合异戊二烯，具有高的催化活性，可获得3,4-结构含量约67%的高分子量无规3,4-聚异戊二烯。催化剂的组成对聚合物的微观结构无明显影响。改变聚合温度，可有效控制聚合物的3,4-结构含量和分子量及分布。

Investigation of high cycle and Very-High-Cycle Fatigue behaviors for a structural steel with smooth and notched specimens

The high cycle and Very-High-Cycle Fatigue (VHCF) properties of a structural steel with smooth and notched specimens were studied by employing a rotary bending machine with frequency of 52.5 Hz. For smooth specimens, VHCF failure did occur at fatigue cycles of 7.1 x 10(8) with the related S-N curve of stepwise tendency. Scanning Electron Microscopy (SEM) was used for the observations of the fracture surfaces It shows that for smooth specimens the crack origination is surface mode in the failure regime of less than 10(7) cycles While at VHCF regime, the material failed from the nonmetallic inclusion lies in the interior of material, leading to the formation of fisheye pattern. The dimensions of crack initiation region were measured and discussed with respect to the number of cycles to failure. The mechanism analysis by means of low temperature fracture technique shows that the nonmetallic inclusion in the interior of specimen tends to debond from surrounding matrix and form a crack. The crack propagates and results to the final failure. The stress intensity factor and fatigue strength were calculated to investigate the crack initiation properties. VHCF study on the notched specimens shows that the obtained S-N curve decreases continuously. SEM analysis reveals that multiple crack origins are dominant on specimen surface and that fatigue crack tends to initiate from the surface of the specimen. Based on the fatigue tests and observations, a model of crack initiation was used to describe the transition of fatigue initiation site from subsurface to surface for smooth and notched specimens. The model reveals the influences of load, grain size, inclusion size and surface notch on the crack initiation transition. (C) 2010 Elsevier Ltd. All rights reserved