Effect of agitation on the performance of an anaerobic sequencing batch biofilm reactor in the treatment of dairy effluents

Agitation rate is an important parameter in the operation of Anaerobic Sequencing Biofilm Batch Reactors (ASBBRs), and a proper agitation rate guarantees good mixing, improves mass transfer, and enhances the solubility of the particulate organic matter. Dairy effluents have a high amount of particulate organic matter, and their anaerobic digestion presents inhibitory intermediates (e. g., long-chain fatty acids). The importance of studying agitation in such batch systems is clear. The present study aimed to evaluate how agitation frequency influences the anaerobic treatment of dairy effluents. The ASBBR was fed with wastewater from milk pasteurisation process and cheese manufacture with no whey segregation. The organic matter concentration, measured as chemical oxygen demand (COD), was maintained at approximately 8,000 mg/L. The reactor was operated with four agitation frequencies: 500 rpm, 350 rpm, 200 rpm, and no agitation. In terms of COD removal efficiency, similar results were observed for 500 rpm and 350 rpm (around 90%) and for 200 rpm and no agitation (around 80%). Increasing the system`s agitation thus not only improved the global efficiency of organic matter removal but also influenced volatile acid production and consumption and clearly modified this balance in each experimental condition.

Intake, water consumption, ruminal fermentation, and stress response of beef heifers fed after different lengths of delays in the daily feed delivery time

Four rumen-fistulated Holstein heifers (134 +/- 1 kg initial BW) were used in a 4 x 4 Latin square design to determine the effects of delaying daily feed delivery time on intake, ruminal fermentation, behavior, and stress response. Each 3-wk experimental period was preceded by 1 wk in which all animals were fed at 0800 h. Feed bunks were cleaned at 0745 h and feed offered at 0800 h (T0, no delay), 0900 (T1), 1000 (T2), and 1100 (T3) from d1 to 21 with measurements taken during wk 1 and 3. Heifers were able to see each other at all times. Concentrate and barley straw were offered in separate compartments of the feed bunks, once daily and for ad libitum intake. Ruminal pH and saliva cortisol concentrations were measured at 0, 4, 8, and 12 h postfeeding on d 3 and 17 of each experimental period. Fecal glucocorticoid metabolites were measured on d 17. Increasing length of delay in daily feed delivery time resulted in a quadratic response in concentrate DMI (low in T1 and T2; P = 0.002), whereas straw DMI was greatest in T1 and T3 (cubic P = 0.03). Treatments affected the distribution of DMI within the day with a linear decrease observed between 0800 and 1200 h but a linear increase during nighttimes (2000 to 0800 h), whereas T1 and T2 had reduced DMI between 1200 and 1600 h (quadratic P = 0.04). Water consumption (L/d) was not affected but decreased linearly when expressed as liters per kilogram of DMI (P = 0.01). Meal length was greatest and eating rate slowest in T1 and T2 (quadratic P <= 0.001). Size of the first meal after feed delivery was reduced in T1 on d 1 (cubic P = 0.05) and decreased linearly on d 2 (P = 0.01) after change. Concentrate eating and drinking time (shortest in T1) and straw eating time (longest in T1) followed a cubic trend (P = 0.02). Time spent lying down was shortest and ruminating in standing position longest in T1 and T2. Delay of feeding time resulted in greater daily maximum salivary cortisol concentration (quadratic P = 0.04), which was greatest at 0 h in T1 and at 12 h after feeding in T2 (P < 0.05). Daily mean fecal glucocorticoid metabolites were greatest in T1 and T3 (cubic P = 0.04). Ruminal pH showed a treatment effect at wk 1 because of increased values in T1 and T3 (cubic P = 0.01). Delaying feed delivery time was not detrimental for rumen function because a stress response was triggered, which led to reduced concentrate intake, eating rate, and size of first meal, and increased straw intake. Increased salivary cortisol suggests that animal welfare is compromised.

Molecular analysis of maltotriose active transport and fermentation by Saccharomyces cerevisiae reveals a determinant role for the AGT1 permease

Incomplete and/or sluggish maltotriose fermentation causes both quality and economic problems in the ale-brewing industry. Although it has been proposed previously that the sugar uptake must be responsible for these undesirable phenotypes, there have been conflicting reports on whether all the known alpha-glucoside transporters in Saccharomyces cerevisiae (MALx1, AGT1, and MPH2 and MPH3 transporters) allow efficient maltotriose utilization by yeast cells. We characterized the kinetics of yeast cell growth, sugar consumption, and ethanol production during maltose or maltotriose utilization by several S. cerevisiae yeast strains (both MAL constitutive and AM inducible) and by their isogenic counterparts with specific deletions of the AGT1 gene. Our results clearly showed that yeast strains carrying functional permeases encoded by the MAL21, MAL31, and/or MAL41 gene in their plasma membranes were unable to utilize maltotriose. While both high-and low-affinity transport activities were responsible for maltose uptake from the medium, in the case of maltotriose, the only low-affinity (K-m, 36 +/- 2 mM) transport activity was mediated by the AGT1 permease. In conclusion, the AGT1 transporter is required for efficient maltotriose fermentation by S. cerevisiae yeasts, highlighting the importance of this permease for breeding and/or selection programs aimed at improving sluggish maltotriose fermentations.

Fast batch injection analysis of H(2)O(2) using an array of Pt-modified gold microelectrodes obtained from split electronic chips

A fast and robust analytical method for amperometric determination of hydrogen peroxide (H(2)O(2)) based on batch injection analysis (BIA) on an array of gold microelectrodes modified with platinum is proposed. The gold microelectrode array (n = 14) was obtained from electronic chips developed for surface mounted device technology (SMD), whose size offers advantages to adapt them in batch cells. The effect of the dispensing rate, volume injected, distance between the platinum microelectrodes and the pipette tip, as well as the volume of solution in the cell on the analytical response were evaluated. The method allows the H(2)O(2) amperometric determination in the concentration range from 0.8 mu mol L(-1) to 100 mu mol L(-1). The analytical frequency can attain 300 determinations per hour and the detection limit was estimated in 0.34 mu mol L(-1) (3 sigma). The anodic current peaks obtained after a series of 23 successive injections of 50 mu L of 25 mu mol L(-1) H(2)O(2) showed an RSD < 0.9%. To ensure the good selectivity to detect H(2)O(2), its determination was performed in a differential mode, with selective destruction of the H(2)O(2) with catalase in 10 mmol L(-1) phosphate buffer solution. Practical application of the analytical procedure involved H(2)O(2) determination in rainwater of Sao Paulo City. A comparison of the results obtained by the proposed ampermetric method with another one which combines flow injection analysis (FIA) with spectrophotometric detection showed good agreement. (C) 2011 Elsevier B.V. All rights reserved.

Time Evolution of the Activation Energy in a Batch Chemical Oscillator

The batch-operated bromate/phosphate/acetone/dual catalyst system was studied at four temperatures between 5 and 35 degrees C. The dynamics was simultaneously followed by potential measurements with platinum and bromide selective electrodes, and spectroscopically at two different wavelengths. By simultaneously recording these four time series it was possible to characterize the dynamics of the sequential oscillations that evolve in time. The existence of three sequential oscillatory patterns at each temperature allowed estimating the activation energies in each case. Along with the activation energy of the induction period, it was possible to trace the time evolution of the overall activation energy at four different stages as the reaction proceeds. The study was carried out for two different sets of initial concentrations and it was observed that the overall activation energy increases as reactants turn into products. This finding was propounded as a result of the decrease in the driving force, or the system`s affinity, of the catalytic oxidative bromination of acetone with acidic bromate, as the closed system evolves toward the thermodynamic equilibrium.

In situ differentiation of labile/inert metal species in Brazilian tropical rivers by means of a time-controlled batch-procedure based on TEPHA resin

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Old beagle dogs have lower faecal concentrations of some fermentation products and lower peripheral lymphocyte counts than young adult beagles

The effects of age on microbiota composition, gut fermentation end-product formation and peripheral lymphocyte numbers were compared between old and young adult Beagle dogs fed four kibble diets differing in yeast cell wall contents. The experiment had a double 4 x 4 Latin square design, one with four mature dogs (4 years old) and the other with four old dogs (10 years old), with four replicates (diets) per dog. In each period a 15d adaptation period preceded a 5d total collection of faeces for the digestibility trial. on day 21, fresh faecal samples were collected for the determination of bacterial enumeration, pH, biogenic amine and short-chain fatty acid. Flow cytometry was used for immunophenotypic evaluation. Dogs were fed four kibble diets with similar composition with 0, 0.15, 0.30 and 0.45% of yeast cell wall (as-fed), respectively. Data were evaluated using general linear models of Statistical Analysis Systems statistical software (P<0.05). No evidence of a difference in faecal bacteria counts between ages was found (total aerobes, total anaerobes, Bifidobacterium, Lactobacillus, Clostridium and Escherichia coli: P. 0.15). Faecal concentrations of butyrate, histamine, agmatine and spermine were lower (P <= 0.05) and faecal pH was higher (P=0.03) in older dogs than in mature adult dogs, suggesting an alteration in bacterial metabolic activity, or in the rate of intestinal absorption of these compounds. Concentrations of T-lymphocytes, T-cytotoxic lymphocytes and B-lymphocytes were also lower (P <= 0.01) in older dogs than in mature adult dogs. The study confirmed alterations in peripheral lymphocytes and revealed a reduced concentration of some fermentation end products in the colon of old dogs.

Biodigestão anaeróbia dos dejetos de cabritos Saanen alimentados com dietas com diferentes proporções volumoso e concentrado

Avaliaram-se os efeitos da idade do animal e da proporção de volumoso nas dietas sobre a biodigestão anaeróbia dos dejetos de cabritos Saanen. Foram utilizadas as fezes produzidas por cabritos Saanen aos 90, 120 e 150 dias de idade e alimentados com dietas de três relações volumoso:concentrado (80:20, 60:40 e 40:60), representando as dietas 1, 2 e 3, respectivamente. Utilizaram-se biodigestores tipo batelada de bancada com capacidade para 12 litros de substrato em fermentação e 8% de sólidos totais iniciais para determinação das produções e dos potenciais de produção de biogás e metano, da redução de sólidos voláteis e quantificação dos teores de minerais no afluente e efluente. As maiores reduções de sólidos voláteis foram observadas nos substratos preparados com as fezes de cabritos aos 150 dias alimentados com a dieta com relação volumoso:concentrado de 40:60. Os melhores rendimentos de substrato ou fezes foram obtidos com os dejetos dos cabritos de 120 e 150 dias de idade alimentados com a dieta com relação volumoso:concentrado 40:60. As maiores concentrações de minerais nos biodigestores foram observadas para as fezes de cabritos de 150 dias de idade alimentados com a dieta com relação volumoso:concentrado 40:60. A biodigestão anaeróbia é eficiente na remoção de coliformes nos dejetos de caprinos, proporcionando efluentes com no máximo 4,3 × 10² coliformes totais termotolerantes por grama de material.

Quali/quantitative characterization of biogas produced in batch digesters supplied with six distinct substrates

Com a finalidade de se analisar quali/quantitativamente o biogás produzido por 6 tipos de substratos, efetuou-se a presente pesquisa no DER/FCAV/UNESP- SP, Brasil. Os substratos utilizados na digestão anaeróbia foram caracterizados como: 1- Esterco de aves de postura (EAP); 2- Esterco de aves de postura triturado (EAPT); 3- Esterco de aves de corte com cama de maravalha (EACM); 4- Esterco de aves de corte com cama de maravalha triturado (EACMT); 5- Esterco de aves de corte com cama de casca de amendoim (EACA), e 6- Esterco de aves de corte com cama de casca de amendoim triturado (EACAT). Dos resultados obtidos, concluiu-se que, em relação à produção acumulada de biogás, o substrato EAPT foi superior aos demais, enquanto EACM apresentou produção acumulada inferior. em geral, os substratos triturados apresentaram maior quantidade de biogás acumulado em relação aos não triturados, exceto o EACAT, com 20,9 m³ inferior ao EACA. O período de produção máxima de biogás teve início entre 45 e 60 dias, começando a decair a partir dos 120 dias. Aos 57 dias após o enchimento dos biodigestores, o gás produzido possuía teores de CH4 superiores a 53%, e a partir dos 99 dias, todos produziram biogás com teores de CH4 superiores a 70%. Os substratos EAP e EAPT apresentaram maiores concentrações de metano no biogás.

Damages of spittlebug on sugarcane quality and fermentation process

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Rumen fermentation and rumen microbes in Nellore steers receiving diets with different lipid contents

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fermentation and aerobic stability of high-moisture corn silages inoculated with different levels of Lactobacillus buchneri

Fermentation and aerobic stability were evaluated in high-moisture corn (HMC) silage inoculated with different levels of Lactobacillus buchneri. The HMC composed of 654 g/kg dry matter (DM) was ensiled in quadruplicate laboratory silos (7 L) per treatment. L. buchneri 40788 was applied at 5 × 10(4); 1 × 10(5); 5 × 10(5); and 1 × 10(6) cfu/g to the ground corn. Silages with no additive were used as controls. After 140 d of ensiling, the silages were subjected to an aerobic stability evaluation for 12 days in which the chemical parameters, microbiological parameters and silage temperature were measured to determine the aerobic deterioration. The lactic acid, acetic acid and propionic acid concentrations did not differ between silages. The fermentation parameters of HMC were not affected by L. buchneri. The HMC containing L. buchneri had a low number of yeast and mould colonies and a more stable pH until in the eighth measurement, which improved the aerobic stability without affecting gas loss. Doses of L. buchneri greater than or equal to 5 × 10(5) cfu/g applied to the HMC were the most efficient in control of aerobic deterioration.

Fermentation and aerobic stability of corn silage inoculated with Lactobacillus buchneri

The characteristics of fermentation and aerobic stability were evaluated in corn silage inoculated with different doses of Lactobacillus buchneri. The whole corn plant (300 g/kg DM) was ensiled in quadruplicate laboratory silos (7L). L. buchneri 40788 was applied at 5×10(4), 1×10(5), 5×10(5) and 1×10(6) cfu/g of fresh forage. Silages with no additive were used as controls. After 130 d of ensiling, the silages were subjected to an aerobic stability evaluation for 12 days, in which chemical and microbiological parameters as well as the temperature of the silage were measured to determine the aerobic deterioration. The addition of L. buchneri resulted in increased acetic acid concentrations. The number of yeast colonies was low in all treated silages. The pH, lactic and propionic acid concentrations did not differ between silages. Under aerobic conditions, all the treated silages showed a low number of yeasts and a great aerobic stability. Therefore, L. buchneri is effective against yeasts and improves the aerobic stability of corn silage in laboratory silos. However, doses equal or superior to 1×10(5) cfu/g of fresh forage were more efficient in the control of aerobic spoilage.

Effect of pelleting and pellet size of a concentrate for intensively reared beef cattle on in vitro fermentation by two different approaches

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Chemical composition and fermentation characteristics of elephant grass silage with biodiesel industry co-products

The objective of this research was to evaluate the effect of three concentrations (3, 6, and 9%) of forage turnip (Raphanus sativus) and physic nut (Jatropha curcas) cakes on dry matter, crude protein, ether extract, neutral detergent fiber, acid detergent fiber, lignin, acid detergent insoluble nitrogen neutral detergent insoluble nitrogen contents, in vitro dry matter digestibility, pH values and concentrations of N-NH3 in elephant grass silages. It was used an entirely randomized design in factorial arrangement [(2x3)+1]. Experimental PVC silos were used and ensiled material was kept for 62 days. The addition of cakes increased the dry matter contents (P<0.05). The fibrous fractions were reduced (P<0.05) with the inclusion of cakes during the grass ensilage and the CP contents increased (P<0.05). The forage turnip cake provided the same pH and N-NH3 values in ideal levels and the physic nut, added to 9%, increased those values (P<0.05). IVDMD was reduced (P<0.05) when the cakes were added. These co-products can be used in small amounts for elephant grass ensilage in order to provide improvement in chemical and fermentation characteristics of the silages. Nevertheless, physic nut cake shows limitations for its use in animal feeding due to the presence of toxic compounds, making necessary studies for their identification and elimination.