Effect of damper and heat source on wind catcher natural ventilation performance

Experimental wind tunnel and smoke visualisation testing and CFD modelling were conducted to investigate the effect of air flow control mechanism and heat source inside rooms on wind catchers/towers performance. For this purpose, a full-scale wind catcher was connected to a test room and positioned centrally in an open boundary wind tunnel. Pressure coefficients (C-p's) around the wind catcher and air flow into the test room were established. The performance of the wind catcher depends greatly on the wind speed and direction. The incorporation of dampers and egg crate grille at ceiling level reduces and regulates the air flow rate with an average pressure loss coefficient of 0.01. The operation of the wind catcher in the presence of heat sources will potentially lower the internal temperatures in line with the external temperatures.

Effect of minerals on casein micelle stability of cows' milk

The effects of minerals on casein micelle stability of individual cows' milk, throughout a complete lactation, were investigated. Calcium and calcium ions, magnesium, phosphorus, sodium, potassium and citrate contents were analysed, together with the following physical properties of milk; pH, ethanol stability, rennet clotting time and coagulum firmness. There was an inverse non-linear relationship between free calcium ion concentration and ethanol stability (ES; r=0.84). Rennet coagulation time showed a weaker relationship with free calcium ion concentration (r=0.44) but a stronger relationship with pH (r=0.66). In addition, samples containing higher amounts of free calcium ions produced a firmer gel. Citrate in natural samples acts as a stabilizing factor, as it slightly improves milk stability. Potassium, on the other hand, exhibited a negative correlation, but only with rennet clotting time (r=-0.52). Throughout lactation the average values were; free Ca 21 concentration 1.88 mm,, pH 6.63, ES 83.2% and clotting time 13.6 min. The equilibrium relationship between pH and free Ca2+ concentration was investigated by adjusting milk pH from 5.9 to 7.1, using acid and alkali. There was a good inverse linear relationship between pH and log (free Ca 21) for individual milk samples, with a gradient of -0.62 and a standard deviation of 0.042.

Long-term effect of volcanic forcing on ocean heat content

Explosive volcanic eruptions cause episodic negative radiative forcing of the climate system. Using coupled atmosphere-ocean general circulation models (AOGCMs) subjected to historical forcing since the late nineteenth century, previous authors have shown that each large volcanic eruption is associated with a sudden drop in ocean heat content and sea-level from which the subsequent recovery is slow. Here we show that this effect may be an artefact of experimental design, caused by the AOGCMs not having been spun up to a steady state with volcanic forcing before the historical integrations begin. Because volcanic forcing has a long-term negative average, a cooling tendency is thus imposed on the ocean in the historical simulation. We recommend that an extra experiment be carried out in parallel to the historical simulation, with constant time-mean historical volcanic forcing, in order to correct for this effect and avoid misinterpretation of ocean heat content changes

Vertical heat transports in the ocean and their effect on time-dependent climate change

In response to increasing atmospheric con- centrations of greenhouse gases, the rate of time- dependent climate change is determined jointly by the strength of climate feedbacks and the e�ciency of pro- cesses which remove heat from the surface into the deep ocean. This work examines the vertical heat transport processes in the ocean of the HADCM2 atmosphere± ocean general circulation model (AOGCM) in experi- ments with CO2 held constant (control) and increasing at 1% per year (anomaly). The control experiment shows that global average heat exchanges between the upper and lower ocean are dominated by the Southern Ocean, where heat is pumped downwards by the wind- driven circulation and di�uses upwards along sloping isopycnals. This is the reverse of the low-latitude balance used in upwelling±di�usion ocean models, the global average upward di�usive transport being against the temperature gradient. In the anomaly experiment, weakened convection at high latitudes leads to reduced diffusive and convective heat loss from the deep ocean, and hence to net heat uptake, since the advective heat input is less a�ected. Reduction of deep water produc- tion at high latitudes results in reduced upwelling of cold water at low latitudes, giving a further contribution to net heat uptake. On the global average, high-latitude processes thus have a controlling in¯uence. The impor- tant role of di�usion highlights the need to ensure that the schemes employed in AOGCMs give an accurate representation of the relevant sub-grid-scale processes.

Cloud statistics and cloud radiative effect for a low-mountain site

In 2007, the Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF) was operated for a nine-month period in the Murg Valley, Black Forest, Germany, in support of the Convective and Orographically-induced Precipitation Study (COPS). The synergy of AMF and COPS partner instrumentation was exploited to derive a set of high-quality thermodynamic and cloud property profiles with 30 s resolution. In total, clouds were present 72% of the time, with multi-layer mixed phase (28.4%) and single-layer water clouds (11.3%) occurring most frequently. A comparison with the Cloudnet sites Chilbolton and Lindenberg for the same time period revealed that the Murg Valley exhibits lower liquid water paths (LWPs; median = 37.5 g m−2) compared to the two sites located in flat terrain. In order to evaluate the derived thermodynamic and cloud property profiles, a radiative closure study was performed with independent surface radiation measurements. In clear sky, average differences between calculated and observed surface fluxes are less than 2% and 4% for the short wave and long wave part, respectively. In cloudy situations, differences between simulated and observed fluxes, particularly in the short wave part, are much larger, but most of these can be related to broken cloud situations. The daytime cloud radiative effect (CRE), i.e. the difference of cloudy and clear-sky net fluxes, has been analysed for the whole nine-month period. For overcast, single-layer water clouds, sensitivity studies revealed that the CRE uncertainty is likewise determined by uncertainties in liquid water content and effective radius. For low LWP clouds, CRE uncertainty is dominated by LWP uncertainty; therefore refined retrievals, such as using infrared and/or higher microwave frequencies, are needed.

The effect of exogenous gonadotropins on ovarian function in goats actively immunized against inhibin

The aim of this investigation was to compare the ovarian response to superovulatory treatments in does before and after inhibin immunization, with a view to optimizing the superovulatory potential of the caprine ovary. To avoid interference by the ovarian cycle, the experiment was conducted out-of-season. At the onset of the experiment 48 does were subjected to treatment with an sc implant of the progestogen norgestomet, combined with a gonadotropin; eight does each received a single injection of 1200 IU eCG, 400 IU eCG or 2 mL physiological saline (control) or six injections (at 12 h intervals) constituting 16 or 5.4 AU pFSH. The does were mated and subjected to embryo collection 6 to 7 d later. Throughout the experiment ovarian function (by ultrasonography) and plasma levels of inhibin antibodies and progesterone were monitored. Of 40 does treated during the first part of the experiment, 48% showed estrus. The ovarian response in does treated with a high or low dose of eCG or a low dose of pFSH was barely in excess of the ovarian response in the saline-treated controls, whereas a superovulatory dose of pFSH (16 AU) gave a satisfactory response of, on average, 14.5 ovulations (yielding 8.8 flushed ova and embryos). Immediately after the does had been subjected to embryo collection they were actively immunized against inhibin by administering two injections of a recombinant α-subunit of ovine inhibin at four week intervals. All immunized does produced antibodies with the maximal titer reached two weeks after the second injection. Groups of immunized does were subjected to the same gonadotropin treatments as before (avoiding allocation of individuals to the same treatments). This time all does showed estrous symptoms. The ovulatory response to the various treatments, including the saline controls, was virtually identical, the overall average being 21.8 follicles and 9.1 ovulations. The average embryo yield per doe was 5.7. The results imply that inhibin acted as the key factor in determining the ovulatory response since no impact of any of the supplementary gonadotropins was noted in inhibin-immunized does. This finding gives rise to the notion that inhibin antibodies may act primarily by an intraovarian paracrine action rather than by reducing the suppressive action of inhibin on pituitary FSH release. Further, these findings confirm earlier reports that eCG is less suitable than FSH for inducing superovulation in goats, and indicate that active immunization against inhibin may be considered a viable alternative to using exogenous gonadotropin for inducing superovulation in goats.

Hyper-parallel tempering Monte Carlo simulations of Ar adsorption in new models of microporous non-graphitizing activated carbon: effect of microporosity

The adsorption of gases on microporous carbons is still poorly understood, partly because the structure of these carbons is not well known. Here, a model of microporous carbons based on fullerene- like fragments is used as the basis for a theoretical study of Ar adsorption on carbon. First, a simulation box was constructed, containing a plausible arrangement of carbon fragments. Next, using a new Monte Carlo simulation algorithm, two types of carbon fragments were gradually placed into the initial structure to increase its microporosity. Thirty six different microporous carbon structures were generated in this way. Using the method proposed recently by Bhattacharya and Gubbins ( BG), the micropore size distributions of the obtained carbon models and the average micropore diameters were calculated. For ten chosen structures, Ar adsorption isotherms ( 87 K) were simulated via the hyper- parallel tempering Monte Carlo simulation method. The isotherms obtained in this way were described by widely applied methods of microporous carbon characterisation, i. e. Nguyen and Do, Horvath - Kawazoe, high- resolution alpha(a)s plots, adsorption potential distributions and the Dubinin - Astakhov ( DA) equation. From simulated isotherms described by the DA equation, the average micropore diameters were calculated using empirical relationships proposed by different authors and they were compared with those from the BG method.

Effect of water-soluble polymers, polyethylene glycol and poly(vinylpyrrolidone),on the gelation of aqueous micellar solutions of Pluronic copolymer F127

The micellization of F127 (E98P67E98) in dilute aqueous solutions of polyethylene glycol (PEG6000 and PEG35000) and poly(vinylpyrrolidone) (PVP K30 and PVP K90) is studied. The average hydrodynamic radius (rh,app) obtained from the dynamic light scattering technique increased with increase in PEG concentration but decreased on addition of PVP, results which are consistent with interaction of the micelles with PEG and the formation of micelles clusters, but no such interaction occurs with PVP. Tube inversion was used to determine the onset of gelation. The critical concentration of F127 for gelation increased on addition of PEG and of PVP K30 but decreased on addition of PVP K90. Small-angle X-ray scattering (SAXS) was used to show that the 30 wt% F127 gel structure (fcc) was independent of polymer type and concentration, as was the d-spacing and so the micelle hard-sphere radius. The maximum elastic modulus (G0 max) of 30 wt% F127 decreased from its value for water alone as PEG was added, but was little changed by adding PVP. These results are consistent with the packed-micelles in the 30 wt% F127 gel being effectively isolated from the polymer solution on the microscale while, especially for the PEG, being mixed on the macroscale.

Exposure to fine particulate matter in ten night clubs in Athens Greece: studying the effect of ventilation, cigarette smoking and resuspension

The aim of the present work is to study the occupants' exposure to fine particulate concentrations in ten nightclubs (NCs) in Athens, Greece. Measurements of PM1 and PM 2.5 were made in the outdoor and indoor environment of each NC. The average indoorPM1 andPM 2.5 concentrations were found to be 181.77 μgm−3 and 454.08 μg m−3 respectively, while the corresponding outdoor values were 11.04 μg m−3 and 32.19 μg m−3. Ventilation and resuspension rates were estimated through consecutive numerical experiments with an indoor air quality model and were found to be remarkably lower than the minimum values recommended by national standards. The relative effects of the ventilation and smoking on the occupants' exposures were examined using multiple regression techniques. Itwas found that given the low ventilation rates, the effect of smoking as well as the occupancy is of the highest importance. Numerical evaluations showed that if the ventilation rates were at the minimum values set by national standards, then the indoor exposures would be reduced at the 70% of the present exposure values.

Effect of anionic co-ligands on structure and magnetic coupling of bis(μ-phenoxo-bridged dinuclear copper(II) complexes

Two phenoxo bridged dinuclear Cu(II) complexes, [Cu2L2(NO2)(2)] (1) and [Cu2L2(NO3)(2)] (2) have been synthesized using the tridentate reduced Schiff-base ligand 2-[(2-dimethylamino-ethylamino)-methyl]-phenol (HL). The complexes have been characterized by X-ray structural analyses and variable-temperature magnetic susceptibility measurements. The structures of the two compounds are very similar having the same tridentate chelating ligand (L) and mono-dentate anionic ligand nitrite for 1 and nitrate for 2. In both complexes Cu(II) is penta-coordinated but the square pyramidal geometry of the copper ions is severely distorted (Addison parameter (tau) = 0.33) in 1 while the distortion is quite small (average tau = 0.11) in 2. These differences have marked effect on the magnetic properties of two compounds. Although both are antiferromagnetically coupled, the coupling constants (J = -140.8 and -614.7 cm (1) for 1 and 2, respectively) show that the coupling is much stronger in 2.

On the effect of I/Q imbalance on MIMO transmit-receive diversity systems

In practice, all I/Q signal processing receivers face the problem of I/Q imbalance. In this paper, we investigate the effect of I/Q imbalance on the performance of MIMO maximal ratio combining (MRC) systems that perform the combining at the radio frequency (RF) level, thereby requiring only one RF chain. Based on a system modeling that takes the I/Q imbalance into account, we evaluate the performance in terms of average symbol error probability (SEP), outage probability and system capacity, which are derived considering transmission over uncorrelated Rayleigh fading channels. Numerical results are provided to illustrate the effects of system parameters, such as the image- leakage ratio, numbers of transmit and receive antennas, and modulation order of quadrature amplitude modulation (QAM), on the system performance.

On the effect of power amplifier nonlinearity on MIMO transmit diversity systems

Nonlinearity of high-power amplifier (HPA) plays a crucial role in the performance of multiple-input multiple-output (MIMO) systems. In this paper, we investigate the performance of MIMO orthogonal space-time block coding (STBC) systems in the presence of nonlinear HPA. Specifically, we assess the impact of HPA nonlinearity on the average symbol error probability (SEP), total degradation (TD), and system capacity of orthogonal STBC in uncorrelated Nakagami-m fading channels. Numerical results are provided and show the effects of several system parameters, such as the output back-off (OBO) of nonlinear HPA, numbers of transmit and receive antennas, and modulation order of quadrature amplitude modulation (QAM), on performance.

A review of measurement-based assessments of the aerosol direct radiative effect and forcing

Aerosols affect the Earth's energy budget directly by scattering and absorbing radiation and indirectly by acting as cloud condensation nuclei and, thereby, affecting cloud properties. However, large uncertainties exist in current estimates of aerosol forcing because of incomplete knowledge concerning the distribution and the physical and chemical properties of aerosols as well as aerosol-cloud interactions. In recent years, a great deal of effort has gone into improving measurements and datasets. It is thus feasible to shift the estimates of aerosol forcing from largely model-based to increasingly measurement-based. Our goal is to assess current observational capabilities and identify uncertainties in the aerosol direct forcing through comparisons of different methods with independent sources of uncertainties. Here we assess the aerosol optical depth (τ), direct radiative effect (DRE) by natural and anthropogenic aerosols, and direct climate forcing (DCF) by anthropogenic aerosols, focusing on satellite and ground-based measurements supplemented by global chemical transport model (CTM) simulations. The multi-spectral MODIS measures global distributions of aerosol optical depth (τ) on a daily scale, with a high accuracy of ±0.03±0.05τ over ocean. The annual average τ is about 0.14 over global ocean, of which about 21%±7% is contributed by human activities, as estimated by MODIS fine-mode fraction. The multi-angle MISR derives an annual average AOD of 0.23 over global land with an uncertainty of ~20% or ±0.05. These high-accuracy aerosol products and broadband flux measurements from CERES make it feasible to obtain observational constraints for the aerosol direct effect, especially over global the ocean. A number of measurement-based approaches estimate the clear-sky DRE (on solar radiation) at the top-of-atmosphere (TOA) to be about -5.5±0.2 Wm-2 (median ± standard error from various methods) over the global ocean. Accounting for thin cirrus contamination of the satellite derived aerosol field will reduce the TOA DRE to -5.0 Wm-2. Because of a lack of measurements of aerosol absorption and difficulty in characterizing land surface reflection, estimates of DRE over land and at the ocean surface are currently realized through a combination of satellite retrievals, surface measurements, and model simulations, and are less constrained. Over the oceans the surface DRE is estimated to be -8.8±0.7 Wm-2. Over land, an integration of satellite retrievals and model simulations derives a DRE of -4.9±0.7 Wm-2 and -11.8±1.9 Wm-2 at the TOA and surface, respectively. CTM simulations derive a wide range of DRE estimates that on average are smaller than the measurement-based DRE by about 30-40%, even after accounting for thin cirrus and cloud contamination. A number of issues remain. Current estimates of the aerosol direct effect over land are poorly constrained. Uncertainties of DRE estimates are also larger on regional scales than on a global scale and large discrepancies exist between different approaches. The characterization of aerosol absorption and vertical distribution remains challenging. The aerosol direct effect in the thermal infrared range and in cloudy conditions remains relatively unexplored and quite uncertain, because of a lack of global systematic aerosol vertical profile measurements. A coordinated research strategy needs to be developed for integration and assimilation of satellite measurements into models to constrain model simulations. Enhanced measurement capabilities in the next few years and high-level scientific cooperation will further advance our knowledge.

Global snow mass measurements and the effect of stratigraphic detail on inversion of microwave brightness temperatures

Snow provides large seasonal storage of freshwater, and information about the distribution of snow mass as Snow Water Equivalent (SWE) is important for hydrological planning and detecting climate change impacts. Large regional disagreements remain between estimates from reanalyses, remote sensing and modelling. Assimilating passive microwave information improves SWE estimates in many regions but the assimilation must account for how microwave scattering depends on snow stratigraphy. Physical snow models can estimate snow stratigraphy, but users must consider the computational expense of model complexity versus acceptable errors. Using data from the National Aeronautics and Space Administration Cold Land Processes Experiment (NASA CLPX) and the Helsinki University of Technology (HUT) microwave emission model of layered snowpacks, it is shown that simulations of the brightness temperature difference between 19 GHz and 37 GHz vertically polarised microwaves are consistent with Advanced Microwave Scanning Radiometer-Earth Observing System (AMSR-E) and Special Sensor Microwave Imager (SSM/I) retrievals once known stratigraphic information is used. Simulated brightness temperature differences for an individual snow profile depend on the provided stratigraphic detail. Relative to a profile defined at the 10 cm resolution of density and temperature measurements, the error introduced by simplification to a single layer of average properties increases approximately linearly with snow mass. If this brightness temperature error is converted into SWE using a traditional retrieval method then it is equivalent to ±13 mm SWE (7% of total) at a depth of 100 cm. This error is reduced to ±5.6 mm SWE (3 % of total) for a two-layer model.

Effect of inclusion of lactulose and Lactobacillus plantarum on the intestinal environment and performance of piglets at weaning

The prebiotic lactulose, a probiotic strain of Lactobacillus plantarum (L. plantarum) and a synbiotic combination of these two agents were evaluated as growth promoters in 25–39-day old commercial weaning pigs. Ninety-six weaning pigs were allocated into 32 pens, taking initial weight into account, and distributed into four groups as follows: a control diet (CTR), the same diet supplemented daily with L. plantarum (109 CFU/mL sprayed on top; 20 mL/pig) (LPN); 10 g/kg lactulose (LAC) or a combination of both treatments (SYN). At day 14, eight piglets from each group were euthanized and proximal colon digesta was sampled for luminal pH, short-chain fatty acids (SCFA) and lactic acid concentrations. Deoxyribonucleic acid was extracted from colonic digesta and the microbial community was profiled by terminal restriction fragment length polymorphism analysis (T-RFLP) and qPCR. Blood urea nitrogen (BUN) and acute-phase proteins (Pig-MAP) were measured. Lactulose treatment (LAC) improved feed intake (P<0.05), average daily gain (P<0.01), feed:gain ratio (P<0.05) and reduced BUN (P<0.01). Both, LAC and LPN treatment, decreased the Enterobacteriaceae:Lactobacillus spp. ratio in the colonic luminal contents (P<0.05). Moreover LPN treatment promoted a decrease in the percentage of branched fatty acids (P<0.01) suggesting a reduction in proteolytic microbial activity. Microbial profiling of colonic luminal contents by T-RFLP revealed changes in some microbial species. Terminal restriction fragments (TRFs) compatible with Bifidobacterium thermoacidophilum were more frequently detected in experimental diets compared to CTR (P<0.05). Pigs receiving SYN diet demonstrated the combined positive effects of individual LAC and LPN treatment although we were not able to show a specific increase in the probiotic strain with the inclusion of lactulose. Collectively, these data suggest the combination of lactulose and L. plantarum acts as a complementary synbiotic, but not as a synergistic combination.