The inventorying of building stone performance-in-use to assess susceptibility to decay

The Natural Stone Database for Northern Ireland was constructed to address the paucity of information available to stone conservation practitioners within the region. Almost 2000 listed buildings and monuments were surveyed over three years to produce an interactive GIS database. This contained information on stone sources, together with details of stone condition and decay processes. This paper uses elements of this GIS to investigate stone decay patterns across Northern Ireland. The results demonstrate that as the level of stone decay increases, so does the proportion of buildings with sandstone as the primary stone type. It appears that a
higher open porosity level combined with Northern Ireland’s wetter climate and maritime location leads to rapid wetting and drying cycles within sandstones. This is coupled with the ingress and crystallisation of marine and other salts within stone pores leading to considerably
higher rates of decay than for any other stone type.

Do spectral gamma ray data really reflect humid-arid palaeoclimates? A test from the Palaeogene Interbasaltic weathered horizons at the Giant’s Causeway, N.Ireland

Since 1999, the rapid, inexpensive and non-destructive use of Th/K and Th/U ratios from spectral gamma ray measurements have been used as a proxy for changes in palaeo-hinterland weathering. This model is tested here by analysis of in situ palaeoweathering horizons where clay mineral contents are well-known. A residual palaeoweathered horizon of Palaeogene laterite (developed on basalt) has been logged at 14 locations across N. Ireland using spectral gamma ray detectors. The results are compared to published elemental and mineralogical data. While the model of K and U loss during the early stages of weathering to smectite and kaolinite is supported, the formation (during progressively more advanced weathering) of gibbsite and iron oxides has reversed the predicted pattern and caused U and Th retention in the weathering profile. The severity (duration, humidity) of weathering and palaeoweathering may be estimated using Th/K ratios as a proxy. The use of Th/U ratios is more problematic should detrital gibbsite (or similar clays) or iron oxides be detected. Mineralogical analysis is needed in order to evaluate the hosts for K, U and Th: nonetheless, the spectral gamma ray machine offers a real-time, inexpensive and effective tool for the preliminary or conjunctive assessment of degrees of weathering or palaeoweathering.

Comportamento e durabilidade de telhas cerâmicas em ambiente marítimo

As telhas cerâmicas são muito utilizadas há séculos no revestimento de coberturas inclinadas em Portugal e em muitos outros países. Alguns casos de degradação acelerada têm vindo a afectar a durabilidade das telhas. Para avaliar o desempenho de telhas cerâmicas em ambiente marítimo foi desenvolvido um estudo experimental baseado em ensaios de envelhecimento artificial acelerado. Este estudo compreende a caracterização de diversos tipos de telhas cerâmicas, o desenvolvimento e realização de ensaios de envelhecimento acelerado realizados em câmara de nevoeiro salino, a avaliação da degradação provocada pelos ensaios acelerados e a comparação com a degradação sofrida por telhas em exposição natural. O estudo pretende reproduzir em laboratório os mecanismos de degradação observados em condições reais e identificar as características mais afectadas, procurando relações significativas entre grandezas relevantes medidas nos materiais antes e depois da acção dos agentes externos. Pretende-se também, com base na análise comparativa dos resultados dos ensaios de envelhecimento sobre diferentes tipos de telhas, identificar parâmetros de composição e de fabrico que contribuem para a degradação e fornecer assim à indústria dados relevantes para melhorar a durabilidade das telhas.

Hidrogeomorfologia e sustentabilidade de recursos hídricos subterrâneos

A água subterrânea de rochas duras é uma fonte importante para fins domésticos, industriais e agrícolas e mesmo para o consumo humano. A geologia, a tectónica, a geomorfologia e as características hidrológicas controlam o fluxo, ocorrência e armazenamento das águas subterrâneas. A disponibilidade da água subterrânea no meio geológico está totalmente dependente das áreas de recarga e de descarga numa determinada bacia. A precipitação é a principal fonte de recarga em aquíferos descontínuos, enquanto que a descarga depende dos declives do terreno e dos gradientes do nível hidrostático e ainda das condições hidrogeológicas do solo. A hidrogeomorfologia é um domínio interdisciplinar emergente, que estuda as relações entre as unidades geomorfológicas e o regime das águas superficiais e subterrâneas de uma determinada área. A compreensão do papel da geomorfologia é essencial para avaliar de forma rigorosa os sistemas hidrogeológicos e os recursos hídricos. Os dados de detecção remota providenciam uma informação espacial valiosa e actualizada da superfície terrestre e dos recursos naturais. Os recentes avanços tecnológicos colocaram as técnicas de detecção remota e os sistemas de informação geográfica (SIG) numa posição cimeira como ferramentas de gestão metodológica. Foi criada, em ambiente SIG, uma base de geo-dados, essencialmente derivada da detecção remota, da cartografia e do trabalho de campo. Esta base de dados, organizada em diferentes níveis de informação, inclui uma avaliação principalmente focalizada no uso do solo, climatologia, declives, geologia, geomorfologia e hidrogeologia. No presente estudo foram cruzados diversos níveis de informação, com a geração de múltiplos mapas temáticos para atingir um quadro integrado dos diversos sectores no Norte e Centro de Portugal. Os sectores em estudo (Caldas da Cavaca, Termas de Entre-os-Rios, Águas de Arouca e Águas do Alardo) estão localizados em sistemas hidrogeológicos predominantemente constituídos por rochas graníticas, por vezes intersectadas por filões de quartzo, aplito-pegmatíticos e doleríticos. Para apoiar a elaboração dos mapas hidrogeomorfológicos foi criada uma base SIG, contendo diversa informação, nomeadamente topografia, hidrografia, litologia, tectónica, morfoestrutura, hidrogeologia, geofísica e uso do solo. Além disso, foram realizadas várias campanhas de campo, as quais permitiram: o estabelecimento dum mapeamento geológico, geomorfológico e hidrogeológico; a caracterização in situ do grau de alteração, resistência e grau de fracturação dos maciços rochosos; o desenvolvimento de um inventário hidrogeológico em conjunto com alguns ensaios expeditos in situ. A interligação entre os parâmetros geomorfológicos, hidrológicos e hidrogeológicos dos sistemas de água subterrânea “normal” e hidromineral destaca a importância de uma cartografia e duma modelação conceptual hidrogeomorfológica. Além disso, contribuirá para um melhor apoio à decisão na gestão sustentável dos recursos hídricos.

Contributo da geoquímica e da sedimentologia na caracterização de influências antropogénicas em ambientes estuarinos

Tese de doutoramento, Geologia (Geoquímica), Universidade de Lisboa, Faculdade de Ciências, 2016

Contribuição para o conhecimento das propriedades pozolânicas da fracção fina resultante da produção de areia de origem granítica

O presente estudo diz respeito a um trabalho de pesquisa no âmbito de uma Tese de Mestrado incluída no segundo ciclo de estudos do curso de Engenharia Geotécnica e Geoambiente, realizado sobre as condições de desidroxilação para a obtenção de metacaulino com propriedades cimentíceas, a partir da fracção argilosa proveniente dos finos residuais da produção de areias de natureza granítica. O produto resultante da alteração e desintegração dos feldspatos constituintes dos granitos são ricos em caulinite. Na natureza e em particular no Norte de Portugal, existem significativos depósitos cauliníticos com características potenciadoras para a produção de metacaulino. O metacaulino utilizado neste estudo foi obtido de uma amostra de argila submetida a 750oC, por um período de tempo de 30 minutos, processo que permitiu a desidroxilação quase total da matéria-prima, transformando esta numa fase amorfa e irreversível, com propriedades pozolânicas. Os metacaulinos, também conhecidos por geopolímeros, são produtos de fácil produção utilizando uma matéria-prima abundante e proporcionam a obtenção de novos produtos que permitem a substituição parcial do cimento Portland normal na composição das pastas de betão, com vantagens significativas no comportamento mecânico e na resistência aos agentes atmosféricos. Neste estudo são apresentados os resultados dos ensaios de caracterização da matéria-prima, das condições de calcinação e do produto resultante da desidroxilação, nomeadamente a determinação da pozolanicidade e das características fundamentais para a aplicabilidade do produto. No âmbito da especialidade de Georrecursos, consideramos que este trabalho está perfeitamente adequado, já que, para além do estudo para o conhecimento das propriedades da matéria-prima, foi possível, através das alterações introduzidas com o tratamento térmico, obter um novo produto, cuja utilização terá importantes reflexos na sustentabilidade dos recursos naturais e sua utilização.

Cartografia e avaliação geotécnica de blocos rochosos em plataformas costeiras (Gaia, NW Portugal)

Mestrado em Engenharia Geotécnica e Geoambiente

Genesis and distribution of Mississippi Valley-type ore assemblages in Middle Silurian strata, Niagara Peninsula, Ontario /

Presently non-commercial occurrences of Mississippi Valley-type ore assemblages in the Middle Silurian strata of the Niagara Peninsula have been studied. Based on this detailed study, a new poly-stage genetic model is proposed which relates ore mineralization in carbonate environments to the evolution of the sedimentary basin. Sulphide ore mineralization occurred during two episodes: 1. During the late diagenesis stage, which is characterized by compaction-maturation of the sediments, the initial mineralization took place by upward and outward movement of connate waters. Metals were probably supplied from all the sediments regardless of their specific lithologies. However, clay minerals were possibly the main contributors. The possible source of sulphur was from petroleum-type hydrocarbons presently mixed with the sediments at the site of ore deposition. Evidence for this is the fact that the greatest abundance of ore minerals is in petroliferous carbonates. The hydrocarbons probably represent liquids remaining after upward migration to the overlying Guelph-Salina reservoirs. The majority of sphalerite and galena formed during this period, as well as accessory pyrite, marcasite, chalcopyrite, chalcocite, arsenopyrite, and pyrrhotite; and secondary dolomite, calcite, celestite, and gypsum. 2. During the presently ongoing surface erosion and weathering phase, which is marked by the downward movement of groundwater, preexisting sulphides were probably remobilized, and trace amounts of lead and zinc were leached from the host material, by groundwaters. Metal sulphides precipitated at, or below, the water table, or where atmospheric oxygen could raise the Eh of groundwaters to the point where soluble metal complexes are unstable and native sulphur co-precipitates with sphalerite and galena. This process, which can be observed today, also results in the transport and deposition of the host rock material. Breakdown of pre-existing sulphide and sulphate, as well as hydrocarbon present in the host rock, provided sulphur necessary for sulphide precipitation. The galena and sphalerite are accompanied by dolomite, calcite, gypsum, anglesite, native sulphur and possibly zincite.

An investigation of geological and geochemical characteristics of late-Quaternay sediments in the Georgian Bay Region, Southern Ontario

Core samples of postglacial sediments and sediment surface samples from Shepherd Lake on the Bruce Peninsula, Harts Lake on the Canadian Shield, and two cores from Georgian Bay (core P-l in the western deep part and core P-7 in the eastern shallow part) have been analyzed for pH, grain size distribution, water content, bulk density, loss on ignition at 4500C and 11000 C, major oxides (Si02 ,A1203,!FeO,MgO,CaO, Na20,K20,Ti02 ,MnO and P205) and trace elements (Ba,Zr,Sr,y,S, Zn,Cu,Ni,Ce and Rb). The sediment in Georgian Bay are generally fine grained (fine silt to very fine silty clay) and the grain size decreases from the Canadian Shield (core p-7) towards the Bruce Peninsula (core P-l) along the assumed direction of sediment transport. This trend coincides with a decrease in sorting coefficient and an increase in roundness. Other physical characteristics, such as water content, bulk density and loss on ignition are positively correlated with the composition of sediments and their compaction, as well as with the energy of the depositional environment. Analyses of sediment surface samples from Shepherd Lake and Harts Lake indicate the influence of bedrock and surficial deposits in the watershed on pH condition that is also influenced by the organic matter content and probably I ! I man's activities. Organic matter content increases significantly in the surface sediment in these small lakes as a result of either natural eutrophication or anthropogenic organic loading. The extremely high organic matter content in Shepherd Lake sediment indicates rapid natural eutrophication in this closed basin and high biological productivity during postglacial time, probably due to high nutrient levels and shallow depth. The chemical composition of the Canadian Shield bedrock is positively correlated with the chemical characteristics of predominantly inorganic lake sediments that were derived from the Shield rocks by glacial abrasion and by postglacial weathering and erosion of both bedrock and surficial deposits. High correlation coefficients were found between organic matter in lake sediments and major oxides (Si02,AI203,.~FeO, MgO,CaO,K20 and MnO) , as well as some trace elements (Ba,Y, S,Zn,Cu,Ni and Rb). The chemical composition of sediments in Harts Lake and core P-7 in Georgian Bay on the Canadian Shield differs from the chemistry of sediments in Shepherd Lake and core P-l in Georgian Bay on the Bruce Peninsula. The difference between cores P-l and P-7 is indicated by values of Si02 , AI203 ,:LFeo,Mgo,CaO,Ba,Zr,Sr,y and S, and also by the organic matter content. This study indicates that the processes of sediment transport, depositional environment, weathering of the rocks and surficial deposits in the watershed, as well as chemical composition of source rocks all affect the chemical characteristics of lake sediments. The stratigraphic changes and variations in lake sediment chemistry with regard to major oxides, trace elements, and organic matter content are probably related to the history of glacial and postglacial lake stages of the Georgian Bay Region and, therefore, the geochemical data can make a useful contribution to a better understanding of the Late-Quaternary history of the Great Lakes.

Étude taphonomique des assemblages fauniques de la formation géologique Mursi et du membre A de la Formation Shungura, Éthiopie

La formation géologique Mursi est datée à plus de 4 millions d’années, ce qui correspond à la période de l’émergence présumée des australopithèques, premiers hominines présentant une bipédie incontestable. La collection faunique Mursi (N=201) est comparée à celle du membre A de la Formation Shungura (N=300) sur une base taphonomique. La taphonomie est la science dédiée aux modes de formation des fossiles ainsi qu’aux traces laissées par ceux-ci. L’objectif principal de ce mémoire est de vérifier quelles sont les différences et ressemblances entre ces deux assemblages fossiles et d’en tirer des interprétations paléoenvironnementales. Pour chacun des agents taphonomiques (météorisation, piétinement, etc.), les fossiles sont gradés en fonction de stades prédéfinis tirés des écrits scientifiques. Finalement, malgré quelques différences (action des carnivores, intempérisation) on constate que les assemblages sont assez semblables et que, comme prédit par les reconstructions paléoenvironnementales préexistantes, leur lien à l’eau est assez bien démontré (groupes de Voorhies, abrasion).

Geochemical, Sedimentological And Remote Sensing Studies Of Kayamkulam Estuary, South West Coast Of India- A Gis Approach

In this study, an attempt has been made to find the textural, geochemical, sedimentological characteristics of sediments and water phases of the kayamkulam estuary located in the Southwest coast of Kerala, besides the impact of gas based thermal power plant located at the northern part of the estuary. Estuaries are an important stage in the transport of the solid weathering product of the earth’s crust. These weathered products or sediments are complex mixtures of a number of solid phases that may include clays, silica, organic matter, metal oxides, carbonates, sulfides and a number of minerals. Studies on the aquatic systems revealed the fact that it posses severe ecological impairments due to heavy discharge of sediments from 44 rivers, the continued disposal of pollutants rich materials from industries, sewage channels, agricultural areas and retting yards

Studies on Ilmenite of Chavara and Manavalakurichi Deposites, Southwest Coast of India

The present work attempts to trace the variation in the physical and chemical behavior of ilmenite, since its release from country rocks and subsequent transportation to the coast through the progressive weathering environments of laterite, sedimentary rocks, rivers and estuarine systems. Since the hinterland of the study area consists of crystalline and sedimentary rocks and their weathered forms (laterites), the contribution of each lithological system to the beach placer is attempted. The results of the study show that the most magnetic fraction contains more content of altered phases than the relatively unweathered fractions. The fractions separated above 0.35A define a high grade of ilmenite ore enriched in Ti content. The lattice volume generally decreases with alteration. The magnetic studies revels that the Chavara ilmenite are found to be made up to low magnetic crops with about 46% of the bulk ilmenite constituted by fractions separated at above 0.35A. In the Manavalakurichi ilmenite on the other hand, around 91% of the beach ilmenite is made of fractions separated at or below 0.3A

Fabrication and characterisation of polymer optical fibers for smart sensing and optical amplification

The thesis presented the fabrication and characterisation of polymer optical fibers in their applications as optical amplifier and smart sensors.Optical polymers such as PMMA are found to be a very good host material due to their ability to incorporate very high concentration of optical gain media like fluorescent dyes and rare earth compounds. High power and high gain optical amplification in organic dye-doped polymer optical fibers is possible due to extremely large emission cross sections of oyes. Dye doped (Rhodamine 6G) optical fibers were fabricated by using indigenously developed polymer optical fiber drawing tower. Loss characterization of drawn dye doped fibers was carried out using side illumination technique. The advantage of the above technique is that it is a nondestructive method and can also be used for studying the uniformity in fiber diameter and doping. Sensitivity of the undoped polymer fibers to temperature and microbending were also studied in its application in smart sensors.Optical amplification studies using the dye doped polymer optical fibers were carried out and found that an amplification of l8dB could be achieved using a very short fiber of length lOcm. Studies were carried out in fibers with different dye concentrations and diameter and it was observed that gain stability was achieved at relatively high dye concentrations irrespective of the fiber diameter.Due to their large diameter, large numerical aperture, flexibility and geometrical versatility of polymer optical fibers it has a wide range of applications in the field of optical sensing. Just as in the case of conventional silica based fiber optic sensors, sensing techniques like evanescent wave, grating and other intensity modulation schemes can also be efficiently utilized in the case of POF based sensors. Since polymer optical fibers have very low Young's modulus when compared to glass fibers, it can be utilized for sensing mechanical stress and strain efficiently in comparison with its counterpart. Fiber optic sensors have proved themselves as efficient and reliable devices to sense various parameters like aging, crack formation, weathering in civil structures. A similar type of study was carried out to find the setting characteristics of cement paste used for constructing civil structures. It was found that the measurements made by using fiber optic sensors are far more superior than that carried out by conventional methods. More over,POF based sensors were found to have more sensitivity as well.

EPDM/CIIR Blends: Compatibility, Morphology and Physical Properties

A detailed study of the blends of ethylene-propylene-diene rubber (EPDM) and chlorobutyl rubber (CIIR) is proposed in this study. These blends may find application in the manufacture of curing diaphragms/curing envelopes for tire curing applications. EPDM possesses better physical properties such as high heat resistance, ozone resistance, cold and moisture resistance, high resistance to permanent defonnation, very good resistance to flex cracking and impact. Because of the low gas and moisture penneability, good weathering resistance and high thermal stability of CIIR, blends of EPDM with CIlR may be attractive, if sufficient mechanical strength can be developed. Although a lot of work has been done on elastomer blends, studies on the blends of EPDM and CIIR rubbers are meagre. Hence in this investigation it is proposed to make a systematic study on the characteristics of EPDM and CIIR rubber blends.The mechanical and physical properties of an elastomer blend depend mainly on the blend compatibility. So in the first part of the study, it is proposed to develop compatible blends of EPDM with CIIR. Various commercial grades of ethylenepropylene- diene rubber are proposed to be blended with a specific grade of chlorobutyl rubber at varying proportions. The extent of compatibility in these blends is proposed to be evaluated based on their mechanical properties such as tensile strength, tear strength and ageing resistance. In addition to the physical property measurements, blend compatibility is also proposed to be studied based on the glass transition behavlour of the blends in relation to the Tg's of the individual components using Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA). The phase morphology of the blends is also proposed to be investigated by Scanning Electron Microscopy (SEM) studies of the tensile fracture surfaces. In the case of incompatible blends, the effect of addition of chlorosulfonated polyethylene as a compatibiliser is also proposed to be investigated.In the second part of the study, the effect of sulphur curing and resin curing on the curing behaviour and the vulcanizate properties of EPDM/CIIR blends are planned to be evaluated. Since the properties of rubber vulcanizates are determined by their network structures, it is proposed to determine the network structure of the vulcanizates by chemical probes so as to correlate it with the mechanical properties.In the third part of the work, the effect of partial precuring of one of the components prior to blending as a possible means of improving the properties of the blend is proposed to be investigated. This procedure may also help to bring down the viscosity mismatch between the constituent e1astomers and provide covulcanization of the blend.The rheological characteristics and processability of the blends are proposed to be investigated in the last part of the study. To explore their possible applications, the air permeability of the blend samples at varying temperatures is proposed to be measured. The thermal diffusivity behaviour of EPDM/CIlR blends is also proposed to be investigated using novel laser technique. The thermal diffusivity of the blends along with the thermal degradation resistance may help to determine whether the blends are suitable for high temperature applications such as in the manufacturing of curing envelope.

Texture, composition and provinance of innershelf sediments between Narakkal and Purakkad, Kerala with special reference to the formation of Mud Banks

The continental shelf of southwest coast of India (Kerala) is broader and . flatter compared to that of the east coast. The unique characteristic feature of the study area (innershelf between Narakkal and Purakkad) is the intermittent appearance of 'mud banks' at certain locations during southwest monsoon. The strong seasonality manifests significant changes in the wind, waves, currents, rainfall, drainage etc., along this area. Peculiar geomorphological variation with high, mid and lowlands in the narrow strip of the hinterland, the geological formations mainly consisting of rocks of metamorphic origin and the humid tropical weathering conditions play significant role in regulating the shelf sedimentation. A complementary pattern of distri bution is observed for clay that shows an abundance in the nearshore. Silt, to a major extent, depicts semblance with clay distribution . Summation of the total asymmetry of grain size distribution are inferred from the variation of skewness and kurtosis.Factor I implies a low energy regime where the transportation and deposition phases are controlled mostly by pelagic suspension process as the factor loadings are dominant on finer phi sizes. The second Factor is inferred to be the result of a high energy regime which gives higher loadings on coarser size fractions. The third Factor which might be a transition phase (medium energy regime) representing the resultant flux of coastal circulation of the re-suspension/deposition and an onshoreoffshore advection by reworking and co-deposition of relict and modern sediments. The spatial variations of the energy regime based on the three end-member factor model exhibits high energy zone in the seaward portion transcending to a low energy one towards the coast.From the combined analysis of granulometry and SEM studies, it is concluded that the sandy patches beyond 20 m depth are of relict nature. They are the resultant responses of beach activity during the lower stand of sea level in the Holocene. Re-crystallisation features on the quartz grains indicate that they were exposed to subaerial weathering process subsequent to thei r deposition