A numerical model for prediction of oil, trajectory due to extraction activity in the north coasts of the Persian Gulf

This thesis considers a three- dimensional numerical model based on 3-D Navier— Stokes and continuity equations involving various wind speeds (North west), water surface levels, horizontal shier stresses, eddy viscosity, densities of oil and gas condensate- water mixture flows. The model is used to simulate the prediction of the surface movement of oil and gas condensate slicks from spill accident in the north coasts of Persian Gulf.

Ultrasound-assisted extraction of R-phycoerythrin from Grateloupia turuturu with and without enzyme addition

The aim of this study was to compare two processes for the extraction of R-phycoerythrin (R-PE) from the red seaweed Grateloupia turuturu: ultrasound-assisted extraction (UAE) and ultrasound-assisted enzymatic hydrolysis (UAEH). Process efficiencies were both evaluated by the yield of R-PE extraction and by the level of liquefaction. Experiments were conducted at 40 and 22 °C, for 6 h, using an enzymatic cocktail and an original ultrasonic flow-through reactor. R-PE appeared very sensitive to temperature, thus 22 °C is strongly recommended for its extraction by UAEH or UAE. However, the higher processing temperature (40 °C) clearly increased the extraction of water-soluble compounds (up to 91% of liquefaction). These two new processes are thus promising alternatives for the extraction of water-soluble components including R-PE, from wet seaweeds, with extraction yields at least similar to conventional solid–liquid extraction.

Study of salinity gradients in the Persian Gulf and an experimental model for electric energy extraction from them using nano-membranes

Salinity gradient power (SGP) is the energy that can be obtained from the mixing entropy of two solutions with a different salt concentration. River estuary, as a place for mixing salt water and fresh water, has a huge potential of this renewable energy. In this study, this potential in the estuaries of rivers leading to the Persian Gulf and the factors affecting it are analysis and assessment. Since most of the full water rivers are in the Asia, this continent with the potential power of 338GW is a second major source of energy from the salinity gradient power in the world (Wetsus institute, 2009). Persian Gulf, with the proper salinity gradient in its river estuaries, has Particular importance for extraction of this energy. Considering the total river flow into the Persian Gulf, which is approximately equal to 3486 m3/s, the amount of theoretical extractable power from salinity gradient in this region is 5.2GW. Iran, with its numerous rivers along the coast of the Persian Gulf, has a great share of this energy source. For example, with study calculations done on data from three hydrometery stations located on the Arvand River, Khorramshahr Station with releasing 1.91M/ energy which is obtained by combining 1.26m3 river water with 0.74 m3 sea water, is devoted to itself extracting the maximum amount of extractable energy. Considering the average of annual discharge of Arvand River in Khorramshahr hydrometery station, the amount of theoretical extractable power is 955 MW. Another part of parameters that are studied in this research, are the intrusion length of salt water and its flushing time in the estuary that have a significant influence on the salinity gradient power. According to the calculation done in conditions HWS and the average discharge of rivers, the maximum of salinity intrusion length in to the estuary of the river by 41km is related to Arvand River and the lowest with 8km is for Helle River. Also the highest rate of salt water flushing time in the estuary with 9.8 days is related to the Arvand River and the lowest with 3.3 days is for Helle River. Influence of these two parameters on reduces the amount of extractable energy from salinity gradient power as well as can be seen in the estuaries of the rivers studied. For example, at the estuary of the Arvand River in the interval 8.9 days, salinity gradient power decreases 9.2%. But another part of this research focuses on the design of a suitable system for extracting electrical energy from the salinity gradient. So far, five methods have been proposed to convert this energy to electricity that among them, reverse electro-dialysis (RED) method and pressure-retarded osmosis (PRO) method have special importance in practical terms. In theory both techniques generate the same amount of energy from given volumes of sea and river water with specified salinity; in practice the RED technique seems to be more attractive for power generation using sea water and river water. Because it is less necessity of salinity gradient to PRO method. In addition to this, in RED method, it does not need to use turbine to change energy and the electricity generation is started when two solutions are mixed. In this research, the power density and the efficiency of generated energy was assessment by designing a physical method. The physical designed model is an unicellular reverse electro-dialysis battery with nano heterogenic membrane has 20cmx20cm dimension, which produced power density 0.58 W/m2 by using river water (1 g NaCl/lit) and sea water (30 g NaCl/lit) in laboratorial condition. This value was obtained because of nano method used on the membrane of this system and suitable design of the cell which led to increase the yield of the system efficiency 11% more than non nano ones.

Extraction and detection of mycotoxins in medicinal and aromatic plants: a case study with Aloysia citrodora P.

Plants frequently suffer contaminations by toxigenic fungi, and their mycotoxins can be produced throughout growth, harvest, drying and storage periods. The objective of this work was to validate a method for detection of toxins in medicinal and aromatic plants, through a fast and highly sensitive method, optimizing the joint co-extraction of aflatoxins (AF: AFB1, AFB2, AFG1 and AFG2) and ochratoxin A (OTA) by using Aloysia citrodora P. (lemon verbena) as a case study. For optimization purposes, samples were spiked (n=3) with standard solutions of a mix of the four AFs and OTA at 10 ng/g for AFB1, AFG1 and OTA, and at 6 ng/g of AFB2 and AFG2. Several extraction procedures were tested: i) ultrasound-assisted extraction in sodium chloride and methanol/water (80:20, v/v) [(OTA+AFs)1]; ii) maceration in methanol/1% NaHCO3 (70:30, v/v) [(OTA+AFs)2]; iii) maceration in methanol/1% NaHCO3 (70:30, v/v) (OTA1); and iv) maceration in sodium chloride and methanol/water (80:20, v/v) (AF1). AF and OTA were purified using the mycotoxin-specific immunoaffinity columns AflaTest WB and OchraTest WB (VICAM), respectively. Separation was performed with a Merck Chromolith Performance C18 column (100 x 4.6 mm) by reverse-phase HPLC coupled to a fluorescence detector (FLD) and a photochemical derivatization system (for AF). The recoveries obtained from the spiked samples showed that the single-extraction methods (OTA1 and AF1) performed better than co-extraction methods. For in-house validation of the selected methods OTA1 and AF1, recovery and precision were determined (n=6). The recovery of OTA for method OTA1 was 81%, and intermediate precision (RSDint) was 1.1%. The recoveries of AFB1, AFB2, AFG1 and AFG2 ranged from 64% to 110% for method AF1, with RSDint lower than 5%. Methods OTA1 and AF1 showed precision and recoveries within the legislated values and were found to be suitable for the extraction of OTA and AF for the matrix under study.

Microwave-assisted solvent extraction and analysis of shikimic acid from plant tissues.

A better method for determination of shikimate in plant tissues is needed to monitor exposure of plants to the herbicide glyphosate [N-(phosphonomethyl)glycine] and to screen the plant kingdom for high levels of this valuable phytochemical precursor to the pharmaceutical oseltamivir. A simple, rapid, and efficient method using microwave-assisted extraction (MWAE) with water as the extraction solvent was developed for the determination of shikimic acid in plant tissues. High performance liquid chromatography was used for the separation of shikimic acid, and chromatographic data were acquired using photodiode array detection. This MWAE technique was successful in recovering shikimic acid from a series of fortified plant tissues at more than 90% efficiency with an interference-free chromatogram. This allowed the use of lower amounts of reagents and organic solvents, reducing the use of toxic and/or hazardous chemicals, as compared to currently used methodologies. The method was used to determine the level of endogenous shikimic acid in several species of Brachiaria and sugarcane (Saccharum officinarum) and on B. decumbens and soybean (Glycine max) after treatment with glyphosate. The method was sensitive, rapid and reliable in all cases.

Assessment of the Occurrence and Potential Risks of Pharmaceuticals and their Metabolites in Fish and Water Using Liquid Chromatography Mass Spectrometry

A comprehensive method for the analysis of 11 target pharmaceuticals representing multiple therapeutic classes was developed for biological tissues (fish) and water. Water samples were extracted using solid phase extraction (SPE), while fish tissue homogenates were extracted using accelerated solvent extraction (ASE) followed by mixed-mode cation exchange SPE cleanup and analyzed by liquid chromatography tandem mass spectrometry (LC-MS/MS). Among the 11 target pharmaceuticals analyzed, trimethoprim, caffeine, sulfamethoxazole, diphenhydramine, diltiazem, carbamazepine, erythromycin and fluoxetine were consistently detected in reclaimed water. On the other hand, caffeine, diphenhydramine and carbamazepine were consistently detected in fish and surface water samples. In order to understand the uptake and depuration of pharmaceuticals as well as bioconcentration factors (BCFs) under the worst-case conditions, mosquito fish were exposed to reclaimed water under static-renewal for 7 days, followed by a 14-day depuration phase in clean water. Characterization of the exposure media revealed the presence of 26 pharmaceuticals while 5 pharmaceuticals including caffeine, diphenhydramine, diltiazem, carbamazepine, and ibuprofen were present in the organisms as early as 5 h from the start of the exposure. Liquid chromatography ultra-high resolution Orbitrap mass spectrometry was explored as a tool to identify and quantify phase II pharmaceutical metabolites in reclaimed water. The resulting data confirmed the presence of acetyl-sulfamethoxazole and sulfamethoxazole glucuronide in reclaimed water. To my knowledge, this is the first known report of sulfamethoxazole glucuronide surviving intact through wastewater treatment plants and occurring in environmental water samples. Finally, five bioaccumulative pharmaceuticals including caffeine, carbamazepine, diltiazem, diphenhydramine and ibuprofen detected in reclaimed water were investigated regarding the acute and chronic risks to aquatic organisms. The results indicated a low potential risk of carbamazepine even under the worst case exposure scenario. Given the dilution factors that affect environmental releases, the risk of exposure to carbamazepine will be even more reduced.

Study of extraction conditions for phenolic compounds from Strawberry fruits

Strawberries are an important source of phytochemicals, namely vitamins and phenolic compounds such as anthocyanins and tannins with antioxidant properties [1]. The yield and phenolic content of natural extracts are dependent on the conditions used for extraction [2]. In the present work three different types of extracting solutions (methanol, ethanol:water and aceton:water), two times of extraction (15 and 60 min) and three ratios of solid/solvent (5/25, 5/50 and 5/100 g/mL) were tested in order to evaluate the efficiency of the extraction of phenolic compounds. Phenolic compounds were determined by Folin-Ciocalteu method [3]. Each assay was performed in triplicate. Regarding the extraction solution, it was possible to observe a slight tendency towards a higher efficiency of acetone:water (AcO:H2O, 60:40), but the differences mioght not be statistically significant. A longer time of contact, 60 min as opposed to 15 min, did not show advantages in the yield of extraction. Considering the factors under study, the results obtained showed that volume of extraction solution was the parameter that most influenced the values obtained. Using a higher volume lead to an increase in the amount of phenolic compounds extracted, in a more pronounced way for 15 min of extraction. For a volume of 25 mL the amount of phenolic compounds quantified ranged from 2.13-2.41 mg GAE/g, and increased 30-68% when it was used 50 mL of solution. Using 100 mL of solution, it was extracted twice as double of phenolic compounds. In case of 60 min, the amount of phenolic compounds quantified in samples obtained with 25 mL of solution ranged from 2.32-2.97 mg GAE/g, and increased for 2.43-4.27 mg GAE/g and 3.98-4.68 mg GAE/g when was used 50 and 100 mL, respectively.

Design principles for maximizing photovoltage in metal-oxide-protected water-splitting photoanodes

Metal oxide protection layers for photoanodes may enable the development of large-scale solar fuel and solar chemical synthesis, but the poor photovoltages often reported so far will severely limit their performance. Here we report a novel observation of photovoltage loss associated with a charge extraction barrier imposed by the protection layer, and, by eliminating it, achieve photovoltages as high as 630mV, the maximum reported so far for water-splitting silicon photoanodes. The loss mechanism is systematically probed in metal-insulator-semiconductor Schottky junction cells compared to buried junction p(+) n cells, revealing the need to maintain a characteristic hole density at the semiconductor/insulator interface. A leaky-capacitor model related to the dielectric properties of the protective oxide explains this loss, achieving excellent agreement with the data. From these findings, we formulate design principles for simultaneous optimization of built-in field, interface quality, and hole extraction to maximize the photovoltage of oxide-protected water-splitting anodes.

Economic feasibility analysis of the implementation of a high value-added molecule extraction system in an olive oil mill

The production of olive oil generates several by-products that can be seen as an additional business opportunity. Among them are the olive pits, already used for heat and/or electricity generation in some mills. They contain compounds that are commercially very interesting and, if recovered, contribute to the sustainability of the olive mills. The work presented in this paper is a preliminary evaluation of the economic feasibility of implementing a system based on a batch prototype with 1 m3 for the extraction of high value-added bioactive molecules from olive pits that are separated during the production of virgin olive oil. For the analysis, a small representative olive mill in Portugal was considered and the traditional Discounted Cash Flow Method was applied. Based on the assumptions made, the simple payback for implementation a system for the extraction of value-added molecules from the olive pits is around 7 years.

Water and sediments geochemistry and elemental fluxes on a Large Dam: case study of Ridracoli reservoir.

Since the study of Large Dam Reservoirs is of worldwide interest, in this PhD project we investigated the Ridracoli reservoir, one of the main water supply in Emilia-Romagna (north-eastern Italy). This work aims to characterize waters and sediments to better understand their composition, interactions and any process that occurs, for a better geochemical and environmental knowledge of the area. Physical and chemical analyses on the water column have shown an alternation of stratification and mixing of water in the reservoir’s water body due to seasonal variations in temperature and density. In particular, it was observed the establishment, in late summer, of anoxic conditions at the bottom, which in turn affects the concentration and mobility of some elements of concern (e.g. Fe and Mn) for the water quality. Sediments within the reservoir and from surrounding areas were analysed for organic matter, total inorganic composition and grain size, assessing the inter-element relationship, grain size, geological background and damming influences on their chemistry, through descriptive statistics, Principal Component Analysis and Cluster Analysis. The reservoir’s area was also investigated by pseudo total composition (Aqua Regia digestion), degree of elements extractability, and enrichment factors, then analysed and compared to limits by law and literature. Sediment cores, interstitial waters, and benthic chamber data from the bottom were of great interest due to organic matter degradation, early diagenesis, mineral formation at water-sediment interface and observed flows. Finally, leaching test and extraction procedures, of environmental interest, showed peculiar partitioning, both regarding spatial and in-depth distribution, and the absence of pollution. Collectively, our results are useful for the comprehension of processes that occur in water and sediments of Ridracoli reservoir, providing important knowledges on the site that could be relevant for the management of the resource and the planning of future interventions.

Emerging plant-based proteins: comparison from extraction to functional properties and food application

The increasing demand for alternatives to meat food products, which is linked to ethical and environmental reasons, highlights the necessity of using different protein sources. Plant proteins provide a valid option, thanks to the relative low costs, high availability and wide supply sources. The current process used to produce plant concentrates and isolates is the alkaline extraction followed by isoelectric precipitation. However, despite the high purity of the proteins, it presents some drawbacks. Innovative protein extraction processes are emerging, with the aim of reducing the environmental impact and the costs, as well as improving the functional properties. In this study, the traditional wet protein extraction and another simplified wet process were used to obtain protein-rich extracts out of different plants. The sources considered in the project were de-oiled sunflower and canola, chickpea, lentils, and the camelina meal, an emerging oleaginous seed interesting for its high content of omega 3. The extracts obtained from the two processes were then analysed for their capacities to hold water and fat, to form gel and a stable foam. Results highlighted strong differences concerning the protein content, yield and functionalities. The extracts obtained with the alkaline process confirmed the literature data about the four plant sources (sunflower, canola, chickpea and lentils) and allow to obtain a camelina concentrate with a protein content of 63 % and a protein recovery of 41 %. The second easiest process was not effective to obtain a protein enrichment in oleaginous sources, whereas an enrichment of 10 and 15 % was obtained in chickpea and lentils, respectively. The functional properties were also completely different: the easiest process produced protein ingredients completely water-soluble at pH 7, with a discrete foaming capacity compared to the extracts obtained with alkaline process. These characteristics could make these extracts suitable for the plant milk-analogue products.

Integration of by-products and waste from agri-food supply chains into the «water-energy-food» nexus (RECOW-ER): the role of fungi

The agricultural sector is undoubtedly one of the sectors that has the greatest impact on the use of water and energy to produce food. The circular economy allows to reduce waste, obtaining maximum value from products and materials, through the extraction of all possible by-products from resources. Circular economy principles for agriculture include recycling, processing, and reusing agricultural waste in order to produce bioenergy, nutrients, and biofertilizers. Since agro-industrial wastes are principally composed of lignin, cellulose, and hemicellulose they can represent a suitable substrate for mushroom growth and cultivation. Mushrooms are also considered healthy foods with several medicinal properties. The thesis is structured in seven chapters. In the first chapter an introduction on the water, energy, food nexus, on agro-industrial wastes and on how they can be used for mushroom cultivation is given. Chapter 2 details the aims of this dissertation thesis. In chapters three and four, corn digestate and hazelnut shells were successfully used for mushroom cultivation and their lignocellulosic degradation capacity were assessed by using ATR-FTIR spectroscopy. In chapter five, through the use of the Surface-enhanced Raman Scattering (SERS) spectroscopy was possible to set-up a new method for studying mushroom composition and for identifying different mushroom species based on their spectrum. In chapter six, the isolation of different strains of fungi from plastic residues collected in the fields and the ability of these strains to growth and colonizing the Low-density Polyethylene (LDPE) were explored. The structural modifications of the LDPE, by the most efficient fungal strain, Cladosporium cladosporioides Clc/1 strain were monitored by using the Scanning Electron Microscope (SEM) and ATR-FTIR spectroscopy. Finally, chapter seven outlines the conclusions and some hints for future works and applications are provided.

Dna Extraction From Filter-paper Spots Of Vaginal Samples Collected After Sexual Violence.

To detect the presence of male DNA in vaginal samples collected from survivors of sexual violence and stored on filter paper. A pilot study was conducted to evaluate 10 vaginal samples spotted on sterile filter paper: 6 collected at random in April 2009 and 4 in October 2010. Time between sexual assault and sample collection was 4-48hours. After drying at room temperature, the samples were placed in a sterile envelope and stored for 2-3years until processing. DNA extraction was confirmed by polymerase chain reaction for human β-globin, and the presence of prostate-specific antigen (PSA) was quantified. The presence of the Y chromosome was detected using primers for sequences in the TSPY (Y7/Y8 and DYS14) and SRY genes. β-Globin was detected in all 10 samples, while 2 samples were positive for PSA. Half of the samples amplified the Y7/Y8 and DYS14 sequences of the TSPY gene and 30% amplified the SRY gene sequence of the Y chromosome. Four male samples and 1 female sample served as controls. Filter-paper spots stored for periods of up to 3years proved adequate for preserving genetic material from vaginal samples collected following sexual violence.

Thermodynamic Study Of The Micellization Of Zwitterionic Surfactants And Their Interaction With Polymers In Water By Isothermal Titration Calorimetry.

The micellization of a homologous series of zwitterionic surfactants, a group of sulfobetaines, was studied using isothermal titration calorimetry (ITC) in the temperature range from 15 to 65 °C. The increase in both temperature and the alkyl chain length leads to more negative values of ΔGmic(0) , favoring the micellization. The entropic term (ΔSmic(0)) is predominant at lower temperatures, and above ca. 55-65 °C, the enthalpic term (ΔHmic(0)) becomes prevalent, figuring a jointly driven process as the temperature increases. The interaction of these sulfobetaines with different polymers was also studied by ITC. Among the polymers studied, only two induced the formation of micellar aggregates at lower surfactant concentration: poly(acrylic acid), PAA, probably due to the formation of hydrogen bonds between the carboxylic group of the polymer and the sulfonate group of the surfactant, and poly(sodium 4-styrenesulfonate), PSS, probably due to the incorporation of the hydrophobic styrene group into the micelles. The prevalence of the hydrophobic and not the electrostatic contributions to the interaction between sulfobetaine and PSS was confirmed by an increased interaction enthalpy in the presence of electrolytes (NaCl) and by the observation of a significant temperature dependence, the latter consistent with the proposed removal of hydrophobic groups from water.

A New Extraction Approach To Correct The Effect Of Apparent Increase In The Secoiridoid Content After Filtration Of Virgin Olive Oil.

In the current study, a new approach has been developed for correcting the effect that moisture reduction after virgin olive oil (VOO) filtration exerts on the apparent increase of the secoiridoid content by using an internal standard during extraction. Firstly, two main Spanish varieties (Picual and Hojiblanca) were submitted to industrial filtration of VOOs. Afterwards, the moisture content was determined in unfiltered and filtered VOOs, and liquid-liquid extraction of phenolic compounds was performed using different internal standards. The resulting extracts were analyzed by HPLC-ESI-TOF/MS, in order to gain maximum information concerning the phenolic profiles of the samples under study. The reduction effect of filtration on the moisture content, phenolic alcohols, and flavones was confirmed at the industrial scale. Oleuropein was chosen as internal standard and, for the first time, the apparent increase of secoiridoids in filtered VOO was corrected, using a correction coefficient (Cc) calculated from the variation of internal standard area in filtered and unfiltered VOO during extraction. This approach gave the real concentration of secoiridoids in filtered VOO, and clarified the effect of the filtration step on the phenolic fraction. This finding is of great importance for future studies that seek to quantify phenolic compounds in VOOs.