Premartensitic and martensitic phase transitions in ferromagnetic Ni2MnGa

We present an experimental study of the premartensitic and martensitic phase transitions in a Ni2MnGa single crystal by using ultrasonic techniques. The effect of applied magnetic field and uniaxial compressive stress has been investigated. It has been found that they substantially modify the elastic and magnetic behavior of the alloy. These experimental findings are a consequence of magnetoelastic effects. The measured magnetic and vibrational behavior agrees with the predictions of a recently proposed Landau-type model [A. Planes et al., Phys. Rev. Lett. 79, 3926 (1997)] that incorporates a magnetoelastic coupling as a key ingredient.

Elastic constants of Ni-Mn-Ga magnetic shape memory alloys

We have measured the adiabatic second order elastic constants of two Ni-Mn-Ga magnetic shape memory crystals with different martensitic transition temperatures, using ultrasonic methods. The temperature dependence of the elastic constants has been followed across the ferromagnetic transition and down to the martensitic transition temperature. Within experimental errors no noticeable change in any of the elastic constants has been observed at the Curie point. The temperature dependence of the shear elastic constant C' has been found to be very different for the two alloys. Such a different behavior is in agreement with recent theoretical predictions for systems undergoing multi-stage structural transitions.

Comment on "Reappraisal of experimental values of third-order elastic constants of some cubic semiconductors and metals"

In a recent paper A. S. Johal and D. J. Dunstan [Phys. Rev. B 73, 024106 (2006)] have applied multivariate linear regression analysis to the published data of the change in ultrasonic velocity with applied stress. The aim is to obtain the best estimates for the third-order elastic constants in cubic materials. From such an analysis they conclude that uniaxial stress data on metals turns out to be nearly useless by itself. The purpose of this comment is to point out that by a proper analysis of uniaxial stress data it is possible to obtain reliable values of third-order elastic constants in cubic metals and alloys. Cu-based shape memory alloys are used as an illustrative example.

Premartensitic transition driven by magnetoelastic interaction in bcc ferromagnetic Ni2MnGa

We show that the magnetoelastic coupling between the magnetization and the amplitude of a short wavelength phonon enables the existence of a first order premartensitic transition from a bcc to a micromodulated phase in Ni2MnGa. Such a magnetoelastic coupling has been experimentally evidenced by ac susceptibility and ultrasonic measurements under an applied magnetic field. A latent heat around 9 J/mol has been measured using a highly sensitive calorimeter. This value is in very good agreement with the value predicted by a proposed model.

Premartensitic and martensitic phase transition in ferromagnetic Ni2MnGa

We present an experimental study of the premartensitic and martensitic phase transitions in a Ni2MnGa single crystal by using ultrasonic techniques. The effect of applied magnetic field and uniaxial compressive stress has been investigated. It has been found that they substantially modify the elastic and magnetic behavior of the alloy. These experimental findings are a consequence of magnetoelastic effects. The measured magnetic and vibrational behavior agrees with the predictions of a recently proposed Landau-type model [A. Planes et al., Phys. Rev. Lett. 79, 3926 (1997)] that incorporates a magnetoelastic coupling as a key ingredient.

Comprehensive Bridge Deck Deterioration Mapping of Nine Bridges by Nondestructive Evaluation Technologies Final Report, January 2011

The primary objective of this research was to demonstrate the benefits of NDT technologies for effectively detecting and characterizing deterioration in bridge decks. In particular, the objectives were to demonstrate the capabilities of ground-penetrating radar (GPR) and impact echo (IE), and to evaluate and describe the condition of nine bridge decks proposed by Iowa DOT. The first part of the report provides a detailed review of the most important deterioration processes in concrete decks, followed by a discussion of the five NDT technologies utilized in this project. In addition to GPR and IE methods, three other technologies were utilized, namely: half-cell (HC) potential, electrical resistivity (ER), and ultrasonic surface waves (USW) method. The review includes a description of the principles of operation, field implementation, data analysis, and interpretation; information regarding their advantages and limitations in bridge deck evaluations and condition monitoring are also implicitly provided.. The second part of the report provides descriptions and bridge deck evaluation results from the nine bridges. The results of the NDT surveys are described in terms of condition assessment maps and are compared with the observations obtained from the recovered cores or conducted bridge deck rehabilitation. Results from this study confirm that the used technologies can provide detailed and accurate information about a certain type of deterioration, electrochemical environment, or defect. However, they also show that a comprehensive condition assessment of bridge decks can be achieved only through a complementary use of multiple technologies at this stage,. Recommendations are provided for the optimum implementation of NDT technologies for the condition assessment and monitoring of bridge decks.

Neuroscience robotics to investigate multisensory integration and bodily awareness.

Humans experience the self as localized within their body. This aspect of bodily self-consciousness can be experimentally manipulated by exposing individuals to conflicting multisensory input, or can be abnormal following focal brain injury. Recent technological developments helped to unravel some of the mechanisms underlying multisensory integration and self-location, but the neural underpinnings are still under investigation, and the manual application of stimuli resulted in large variability difficult to control. This paper presents the development and evaluation of an MR-compatible stroking device capable of presenting moving tactile stimuli to both legs and the back of participants lying on a scanner bed while acquiring functional neuroimaging data. The platform consists of four independent stroking devices with a travel of 16-20 cm and a maximum stroking velocity of 15 cm/s, actuated over non-magnetic ultrasonic motors. Complemented with virtual reality, this setup provides a unique research platform allowing to investigate multisensory integration and its effects on self-location under well-controlled experimental conditions. The MR-compatibility of the system was evaluated in both a 3 and a 7 Tesla scanner and showed negligible interference with brain imaging. In a preliminary study using a prototype device with only one tactile stimulator, fMRI data acquired on 12 healthy participants showed visuo-tactile synchrony-related and body-specific modulations of the brain activity in bilateral temporoparietal cortex.

Using Scanning Lasers for Real-Time Pavement Thickness Measurement, TR-538, 2006

Due to limited budgets and reduced inspection staff, state departments of transportation (DOTs) are in need of innovative approaches for providing more efficient quality assurance on concrete paving projects. The goal of this research was to investigate and test new methods that can determine pavement thickness in real time. Three methods were evaluated: laser scanning, ultrasonic sensors, and eddy current sensors. Laser scanning, which scans the surface of the base prior to paving and then scans the surface after paving, can determine the thickness at any point. Also, scanning lasers provide thorough data coverage that can be used to calculate thickness variance accurately and identify any areas where the thickness is below tolerance. Ultrasonic and eddy current sensors also have the potential to measure thickness nondestructively at discrete points and may result in an easier method of obtaining thickness. There appear to be two viable approaches for measuring concrete pavement thickness during the paving operation: laser scanning and eddy current sensors. Laser scanning has proved to be a reliable technique in terms of its ability to provide virtual core thickness with low variability. Research is still required to develop a prototype system that integrates point cloud data from two scanners. Eddy current sensors have also proved to be a suitable alternative, and are probably closer to field implementation than the laser scanning approach. As a next step for this research project, it is suggested that a pavement thickness measuring device using eddy current sensors be created, which would involve both a handheld and paver-mounted version of the device.

Conduit artery compliance and distensibility are not necessarily reduced in hypertension.

The goal of this study was to investigate whether the elastic behavior of conduit arteries of humans or rats is altered as a result of concomitant hypertension. Forearm arterial cross-sectional compliance-pressure curves were determined noninvasively by means of a high precision ultrasonic echo-tracking device coupled to a photoplethysmograph (Finapres system) allowing simultaneous arterial diameter and finger blood pressure monitoring. Seventeen newly diagnosed hypertensive patients with a humeral blood pressure of 163/103 +/- 4.4/2.2 mm Hg (mean +/- SEM) and 17 age- and sex-matched normotensive controls with a humeral blood pressure of 121/77 +/- 3.2/1.9 mm Hg were included in the study. Compliance-pressure curves were also established at the carotid artery of 16-week-old anesthetized spontaneously hypertensive rats (n = 14) as well as Wistar-Kyoto normotensive animals (n = 15) using the same echo-tracking device. In these animals, intra-arterial pressure was monitored in the contralateral carotid artery. Mean blood pressures averaged 197 +/- 4 and 140 +/- 3 mm Hg in the hypertensive and normotensive rats, respectively. Despite the considerable differences in blood pressure, the diameter-pressure and cross-sectional compliance-pressure and distensibility-pressure curves were not different when hypertensive patients or animals were compared with their respective controls. These results suggest that the elastic behavior of a medium size muscular artery (radial) in humans and of an elastic artery (carotid) in rats is not necessarily altered by an increase in blood pressure.

Investigation of Steel-Stringer Bridges: Superstructures and Substructures, Volume I, TR-522, 2007

There are hundreds of structurally deficient or functionally obsolete bridges in the state of Iowa. With the majority of these bridges located on rural county roads where there is limited funding available to replace the bridges, diagnostic load testing can be utilized to determine the actual load carrying capacity of the bridge. One particular family or fleet of bridges that has been determined to be desirable for load testing consists of single-span bridges with non-composite, cast-in-place concrete decks, steel stringers, and timber substructures. Six bridges with poor performing superstructure and substructure from the aforementioned family of bridges were selected to be load tested. The six bridges were located on rural roads in five different counties in Iowa: Boone, Carroll, Humboldt, Mahaska, and Marshall. Volume I of this report focuses on evaluating the superstructure for this family of bridges. This volume discusses the behavior characteristics that influence the load carrying capacity of this fleet of bridges. In particular, the live load distribution, partial composite action, and bearing restraint were investigated as potential factors that could influence the bridge ratings. Implementing fleet management practices, the bridges were analyzed to determine if the load test results could be predicted to better analyze previously untested bridges. For this family of bridges it was found that the ratings increased as a result of the load testing demonstrating a greater capacity than determined analytically. Volume II of this report focuses on evaluating the timber substructure for this family of bridges. In this volume, procedures for detecting pile internal decay using nondestructive ultrasonic stress wave techniques, correlating nondestructive ultrasonic stress wave techniques to axial compression tests to estimate deteriorated pile residual strength, and evaluating load distribution through poor performing timber substructure elements by instrumenting and load testing the abutments of the six selected bridges are discussed. Also, in this volume pile repair methods for restoring axial and bending capacities of pile are developed and evaluated.

Characterizing the impact of minor cannula design modification.

OBJECTIVE: Bench evaluation of the hydrodynamic behavior of venous cannulas is a valuable technique for the analysis of their performance during cardiopulmonary bypass (CPB). The aim of this study was to investigate the effect of the internal diameter of the extracorporeal connecting tube of venous cannulas on flow rate (Q), pressure drop (delta P), and cannula resistance (delta P/Q²) values, using a computer assisted test bench.¦METHODS: An in vitro circuit was set up with silicone tubing between the test cannula encased in a movable reservoir, and a static reservoir. The delta P, defined as the difference between the drainage pressure and the preload pressure, was measured using high-fidelity Millar pressure transducers. Q was measured using an ultrasonic flowmeter. Data display and data recording were controlled using virtual instruments in a stepwise fashion.¦RESULTS: The 27 F smartcanula® with a 9 mm connecting tube diameter showed 17% less resistance compared to that with an 8 mm connecting tube diameter. Q values were 7.22±0.1 and 7.81±0.04 L/min for cannulas with 8 mm and 9 mm connecting tube diameters, respectively. The delta P/Q² ratio values were 72% lower for the Medtronic cannula with a 9 mm connecting tube diameter compared to that with an 8 mm connecting tube diameter. Q values for the Medtronic cannula were 3.94±0.23 and 6.58±0.04 L/min with 8 mm and 9 mm connecting tube diameters, respectively. The 27 F smartcanula® showed 13% more flow rate compared to the 28 F Medtronic cannula using the unpaired Student t-test (p<0.0001).¦CONCLUSIONS: Our results demonstrated that Q was increased but delta P and delta P/Q² values were significantly decreased when the connecting tube diameter was increased for venous cannulas. The connecting tube diameter significantly affected the resistance to liquid flow through the cannula. Smartcanulas® outperform Medtronic cannulas.

Laivan hitsattujen runkorakenteiden ainettarikkomattoman tarkastuksen ohjauksen ja valvonnan kehittäminen

Laivan rungonvalmistuksen laadunvarmistuksessa käytetään viranomaisten valvomia NDT-tarkastuksia vaatimustenmukaisuuden varmistamiseksi. Yleisimmin käytettävät NDT-tarkastusmenetelmät laivanrakennuksessa ovat visuaali-, röntgen-, ultraääni-, magneettijauhe- ja tunkeumanestetarkastukset. Diplomityön tavoitteena oli kehittää laivan hitsattujen runkorakenteiden ainettarikkomattoman tarkastuksen ohjausta ja valvontaa Aker Finnyards:n Turun telakalla. Työn alussa selvitettiin NDT-tarkastuksen ohjauksen ja valvonnannykytila ja tunnistettiin kehityskohteita. Tutkimusmenetelminä käytettiin työnmittausta ja havainnointitutkimusta. Merkittävimmiksi kehityskohteiksi havaittiinyleinen epätietoisuus NDT-tarkastuksista laivan runkoprosessissa, selkeän NDT-tarkastusten ohjausjärjestelmän puuttuminen sekä puutteellinen valvonta. Kehityskohteiden tunnistamisen perusteella luotiin toimintamalli NDT-tarkastusten ohjauksen ja valvonnan kehittämiseksi. Toimintamallissa on kuvattuna NDT-tarkastusprosessin tekijät ja informaatiovirrat. Toimintamalli on tarvittaessa päivitettävissä.

Investigation phytochimique d'une brosse à dents africaine Zanthoxylum zanthoxyloides (Lam.) Zepernick et Timler (Syn. Fagara zanthoxiloides L.) (Rutaceae)

Résumé: Dans le but de rechercher de nouveaux composés naturels à intérêt thérapeutique, les extraits dichlorométhanique et méthanolique de Zanthoxylum zanthoxyloides (Lam.) Zepernick et Timler (Syn. Fagara zanthoxyloides L.) (Rutaceae), une brosse à dents africaine ont été soumis à un criblage chimique et biologique. Un dépistage des activités: antifongiques contre le champignon phytopathogène Cladosporium cucumerinum et la levure commensale responsable de mycoses chez l'homme Candida albicans, antibactérienne contre la bactérie opportuniste Bacillus subtilis, larvicide contre le moustique vecteur de la fièvre jaune Aedes aegypti et molluscicide contre Biomphalaria glabrata, un escargot impliqué dans la transmission de la schistosomiase urinaire a été réalisé. Les propriétés antiradicalaires et inhibitrices de l'acétylcholinestérase de ces extraits ont aussi été dépistées. Sur la base des résultats obtenus lors de ce screening, l'investigation phytochimique de ces extraits a été entreprise. Elle a abouti à l'isolement de 14 composés, actifs pour la majorité contre Cladosporium cucumerinum et Bacillus subtilis, dont la structure a été établie au moyen de méthodes spectroscopiques (UV, MS, IR, 1H- et 13C-NMR). Des méthodes chimiques (hydrolyse, acétylation) ont été requises pour la confirmation de structures. L'extrait dichlorométhanique a fourni un nouveau composé, un dérivé du phényléthane, ainsi que dix composés connus, dont trois dérivés du phénylpropane, un lignane, un alcaloïde de la famille des benzophénanthridines, un triterpène, deux amides phénoliques et deux amides oléfmiques. L'extrait méthanolique a fourni un nouveau composé avec une fonction endoperoxyde, qui avait montré une activité inhibitrice modérée de l'acétylcholinestérase, ainsi que l'hespéridine et un dérivé de la chélérythrine. Par ailleurs, l'analyse LC/UV/APC1-MS de cet extrait a permis de détecter on-une sept produits connus. Parmi ces composés, se trouvent l'acide divanilloylquinique, la chélérythrine et quatre de ses dérivés: norchélérythrin.e, 6-(2-oxybutyl) dihydrochélérythrine, 6-hydroxy-dihydrochélérythrine et avicine, ainsi qu'une amide phénolique, l'amottianamide. La présence de ces dérivés de la chélérythrine a été mise en évidence dans deux autres espèces du même genre lors d'une étude LC/UV/APCI-MS comparative. Les activités fongicides contre Cladosporium cucumerinum et Candida albicans et bactéricides contre Bacillus subtilis et Streptococcus mutans ATCC 25175, mises en évidence sur plaque CCM et par les tests de dilution dans l'agar de ces composés, permettent de justifier l'utilisation de Zanthoxylum zanthoxyloides (Lam.) Zepemick et Timler comme brosse à dents africaine. Les techniques couplées de pointe utilisées dans cette étude ont montré leur apport inestimable dans le domaine de la recherche phytochimique et les applications futures dans le domaine de déréplication d'extraits bruts. Abstract: With the aim of discovering new natural therapeutics, the dichloromethane and methanol extracts of the African toothbrush tree Zanthoxylum zanthoxyloides (Lam.) Zepernick et Timler (Syn. Fagara zanthoxyloides L.) (Rutaceae), were submitted to biological and chemical assays. The former included: the antifimgal activities of the extracts against the phytopathogenic fungus Cladosporium cucumerinum, the commensal yeast which causes human mycoses Candida albicans, the bactericidal activity against the opportunistic bacteria Bacillus subtilis, the larvicidal activity against the yellow fever-transmitting mosquito Aedes aegypti and the molluscicidal effect on the snail Biomphalaria glabrata involved in the transmission of urinary schistosomiasis. The antiradical and acetylcholinesterase-inhibiting properties of these extracts were also investigated. On the basis of these results, a phytochemical investigation of the dichloromethane and methanol extracts of Zanthoxylum zanthoxyloides was undertaken. Their fractionation led to the isolation of 14 compounds, the majority of which were active against Cladosporium cucumerinum and Bacillus subtilis, whose structures were elucidated by spectroscopic techniques (UV, MS, IR, 1H- and 13C-NMR). Chemical methods (hydrolysis, acetylation) were performed to confirm the structures. The dichloromethane extract yielded a new phenylethane derivative, together with ten known compounds: three phenylpropane derivatives, a lignan, a benzophenanthridine alkaloid, a triterpene and four phenolic and olefinic amides. The methanol extract yielded a new compound with an endoperoxide moiety, which showed moderate acetylcholinesterase-inhibiting activity, together with hesperidin and a chelerythrine derivative. Seven more compounds were detected on-line by LC/UV/APCI-MS. Among the compounds detected were divanilloylquinic acid, chelerythrine and four chelerythrine derivatives: norchelerythrine, 6-(2-oxybuty1)-dihydrochelerythrine, 6-hydroxy dihydrochelerythrine and avicine, together with the phenolic amide amottianamide. Most of the chelerythrine derivatives were also found in two other Zanthoxylum species following LC/UV/APCI-MS analysis. The antifungal activities against Cladosporium cucumerinum and Candida albicans and antibacterial activities against Bacillus subtilis and Streptococcus mutans ATCC 25175, may explain the utilization in traditional medicine of the roots of this plant as a toothbrush. The advanced hyphenated techniques used in this study showed their inestimable contribution to the field of phytochemical research and applications in the field of dereplication of crude extracts.