Avaliação do processo eletrolítico em corrente alternada no tratamento de água de produção

The main objective was to study the treatment of wastewater generated by the oil industry. This work consisted of tests of electroflocculation with alternate current (AC), and chemical coagulation. The removal efficiencies of organic load were evaluated by the removal of oils and greases, color and turbidity. The parameters investigated were the change in alternate current frequency, the initial pH, the distance between electrodes, the applied potential and time lapse. From the results, one may conclude that the electroflocculation process is potential applicability to the effluent studied, while chemical coagulation was not successful.

Quantitative analysis of two important epidemiological features of the common bean: Phaeoisariopsis griseola pathosystem

This work quantifies two important epidemiological features of the bean (Phaseolus vulgaris)/Phaeoisariopsis griseola pathosystem. The first is the effect of the number of nights of leaf wetness on infection efficiency. Infection efficiency was below 10% when inoculated leaflets were exposed to less than two nights of leaf wetness. Optimum infection efficiencies were obtained after three to four nights of leaf wetness, at about 50%. Further nights of leaf wetness did not increase the infection efficiency. The second feature quantified is the relative rate of leaflet defoliation for varying levels of angular leaf spot severity. It increased with disease severity according to a logarithm-like curve, and a relative rate of 0.23 day-1 was estimated for a severity of 18%. The implications of these results on the disease epidemiology are discussed.

Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Numerical modelling of small supersonic axial flow turbines

Supersonic axial turbine stages typically exhibit lower efficiencies than subsonic axial turbine stages. One reason for the lower efficiency is the occurrence of shock waves. With higher pressure ratios the flow inside the turbine becomes relatively easily supersonic if there is only one turbine stage. Supersonic axial turbines can be designed in smaller physical size compared to subsonic axial turbines of same power. This makes them good candidates for turbochargers in large diesel engines, where space can be a limiting factor. Also the production costs are lower for a supersonic axial turbine stage than for two subsonic stages. Since supersonic axial turbines are typically low reaction turbines, they also create lower axial forces to be compensated with bearings compared to high reaction turbines. The effect of changing the stator-rotor axial gap in a small high (rotational) speed supersonic axial flow turbine is studied in design and off-design conditions. Also the effect of using pulsatile mass flow at the supersonic stator inlet is studied. Five axial gaps (axial space between stator and rotor) are modeled using threedimensional computational fluid dynamics at the design and three axial gaps at the off-design conditions. Numerical reliability is studied in three independent studies. An additional measurement is made with the design turbine geometry at intermediate off-design conditions and is used to increase the reliability of the modelling. All numerical modelling is made with the Navier-Stokes solver Finflo employing Chien’s k ¡ ² turbulence model. The modelling of the turbine at the design and off-design conditions shows that the total-to-static efficiency of the turbine decreases when the axial gap is increased in both design and off-design conditions. The efficiency drops almost linearily at the off-design conditions, whereas the efficiency drop accelerates with increasing axial gap at the design conditions. The modelling of the turbine stator with pulsatile inlet flow reveals that the mass flow pulsation amplitude is decreased at the stator throat. The stator efficiency and pressure ratio have sinusoidal shapes as a function of time. A hysteresis-like behaviour is detected for stator efficiency and pressure ratio as a function of inlet mass flow, over one pulse period. This behaviour arises from the pulsatile inlet flow. It is important to have the smallest possible axial gap in the studied turbine type in order to maximize the efficiency. The results for the whole turbine can also be applied to some extent in similar turbines operating for example in space rocket engines. The use of a supersonic stator in a pulsatile inlet flow is shown to be possible.

Kylmätilojen kuljetinkäyttöjen energiatehokkuus

We study how conveyor drives in refrigerating rooms affect total energy costs. Studied conveyor drives are different types of gear motor drives. Energy efficiencies of the conveyor drives are determined by using direct torque measurement and energy costs of the conveyor drives are approximated from these results. From the measurement results and the approximated total costs it can be seen how the energy efficiency of a conveyor drive has a considerable influence on the total costs, especially, with large operating hours. An energy efficient conveyor drive can minimize the total energy costs by reducing the energy consumption of the conveyor motor while cooling costs in refrigerated rooms are also reduced.

Uuteaineet BCTMP-prosessissa

Diplomityö tehtiin M-real Joutsenon BCTMP-tehtaalle. Työn aiheena oli tehdä uuteaine- ja metallikartoitus eri prosessivaiheiden massoista ja suodoksista BCTMP-tehtaassa. BCTMPmassaa käytetään muun muassa elintarvikekartongin keskikerroksessa. Pakattaviin kartonkeihin suoraan kosketuksissa olevat elintarvikkeet ovat alttiita haju- ja makuvivahteille. Hajut ja maut voivat saada alkunsa kartongin komponenteista, kuten BCTMP-massasta, kartongin päällystysaineista ja kartongin jatkojalostuksessa käytetyistä painoväreistä. Diplomityön teoriaosuudessa keskityttiin puun lipofiilisiin uuteaineisiin ja erityisesti komponentteihin, jotka aiheuttavat haju- ja makuongelmia. Teoriaosuudessa käsiteltiin myös haju- ja makuominaisuuksien muodostumiseen vaikuttavia tekijöitä sekä kerrottiin mahdollisista uuteaineiden poistomenetelmistä. Teoriaosuudessa esiteltiin analysointimenetelmiä, joita käytettiin kokeellisessa osassa. Kokeellisessa osassa esiteltiin valmistettavan massan laatuspesifikaatiot ja toteutuneet laatutrendit. Samassa tutkittiin massan analysointimenetelmien tuloksien korrelaatioita kokonaisuuteaineiden toteamiseksi. Seuraavaksi käsiteltiin syksyllä 2010 ja talvella 2011 tehtyjä prosessin uuteainekartoituksia, jossa muun muassa tutkittiin eri prosessivaiheiden massojen ja suodoksien uuteainemääriä ja –komponentteja. Kartoituksien yhteydessä laskettiin prosessin uuteainetaseita ja prosessin pesutehokkuuksia. Samalla tutkittiin siirtymämetallimääriä, jotka osaltaan vaikuttavat haju- ja makuominaisuuksiin. Kokeellisen osan korrelaatiovertailuissa huomattiin, että merkittävin korrelaatio kokonaisuuteaineisiin on viimeisen massan pesuvaiheen suodoksen sameudella, liki 80 %. Heksanaalipotentiaalin ja uuteaineen korrelaatio oli myös noin 80 %. Valmiista massasta tehdyn kemiallisen hapen kulutuksen eli COD:n korrelaatio uuteaineisiin oli vain 38 %. Prosessikartoituksen tuloksista laskettujen pesuvaiheiden erotustehokkuudet olivat hyvät.

Experimental alternatives for evaluation of progenies and clones in eucalyptus breeding programs

The feasibility of using augmented block designs and spatial analysis methods for early stage selection in eucalyptus breeding programs was tested. A total of 113 half-sib progenies of Eucalyptus urophylla and eight clones were evaluated in an 11 x 11 triple lattice experiment at two locations: Posto da Mata (Bahia, Brazil) and São Mateus (Minas Gerais, Brazil). Four checks were randomly allocated within each block. Plots consisted of 15 m long rows containing 6 plants spaced 3 m apart. The girth at breast height (cm/plant) was evaluated at 19 and 26 months of age. Variance analyses were performed according to the following methods: lattice design, randomized complete block design, augmented block design, Papadakis method, moving means method, and check plots. Comparisons among different methods were based on the magnitude of experimental errors and precision of the estimates of genetic and phenotypic parameters. General results indicated that augmented block design is useful to evaluate progenies and clones in early selection in eucalyptus breeding programs using moderate and low selection intensities. However, this design is not suitable for estimating genetic and phenotypic parameters due to its low precision. Check plots, nearest neighbour, Papadakis (1937), and moving means methods were efficient in removing the heterogeneity within blocks. These efficiencies were compared to that in lattice analysis for estimation of genetic and phenotypic parameters.

”Jos tietää, mitä haluaa.” Seurantatutkimus lukio-opiskelijoiden itsesäätelystä, opiskelun kulusta ja odotusten toteutumisesta

Tutkimuksen päätarkoituksena on selvittää lukio-opiskelijoiden käsityksiä oppimisensa itsesäätelystrategioista. Lukiokoulutuksessa toteutetut muutokset kuten valinnanmahdollisuuksien lisääntyminen ovat antaneet lukio-opiskelijoille kasvaneen mahdollisuuden omanlaisensa lukio-opiskelupolun suunnitteluun ja yksilölliseen tavoitteenasetteluun. Työssä tarkastellaan myös lukio-opiskelijoiden opintojen kulkua, erilaisia opiskeluodotuksia ja niiden toteutumista sekä näiden yhteyttä itsesäätelyyn. Tutkimus toteutettiin seurantatutkimuksena, jossa kyselylomakkeilla kerättiin tietoa syksyllä 2004 Turun kaupungin suomenkielisissä päivälukioissa (10 koulua) opintonsa aloittavilta opiskelijoilta kahdesti; ensimmäisenä ja kolmantena opiskeluvuotena. Tutkimuksessa oli mukana 245 opiskelijaa, 142 tyttöä ja 103 poikaa. Tutkimuksen vastausprosentti oli 84 %. Kyselylomakkeiden itsesäätelyä ja oppimisorientaatioita koskevat kysymykset pohjautuivat Jan Vermuntin ILS-oppimistyylimittariin (Inventory of Learning Styles) (Vermunt 1994; 1996). Lisäksi haastateltiin 15 tutkimuksessa mukana ollutta opiskelijaa. Kyselylomakeaineisto analysoitiin ristiintaulukoinneilla, korrelaatiokertoimilla, t-testeillä ja erilaisilla varianssianalyyseillä. Itsesäätelystrategiamittarin neljän summamuuttujan oletus testattiin erikseen mittauksissa 1 ja 2 konfirmatorisen faktorianalyysin avulla. Tutkimuksessa identifioitiin klusterianalyysillä tehdyssä ryhmittelyssä neljä erilaista lukio-opiskelijaryhmää: menestyvät navigoijat, tavalliset tasapainoilijat, säätelemättömät kulkeutujat ja ylikuormittuneet avuntarvitsijat. Navigoijille on tyypillistä niin prosessin/ tulosten kuin sisällön suhteen korkea itsesäätely. Tyypillinen piirre navigoijien kohdalla on myös ulkoisen säätelyn korkea taso. Avuntarvitsijat eroavat muista ryhmistä selkeästi korkeampien puutteellisten säätelystrategioidensa perusteella, vaikka heidän itsesäätelynsä on suhteellisesti niihin ja muihin ryhmiin nähden melko korkealla tasolla. Tasapainoilijat sijoittuvat itsesäätelyn ja ulkoisen säätelyn osalta ryhmien keskitasolle. Kulkeutujien itsesäätely samoin kuin ulkoinen säätely ovat ryhmien matalinta tasoa. Tuloksista nähdään, että kehittyneemmällä itsesäätelyllä on selvä yhteys lukio-opintojen sujuvuuteen ja opintomenestykseen, mutta noin kolmasosalle opiskelijoista itsesäätelevä, suunnitelmallinen tavoitteenasettelu on vaikeaa. Navigoijilla ja tasapainoilijoilla opiskelu on sekä heille itselleen mielekästä että ulkoisesti arvioituna tehokasta. Joidenkin opiskelijoiden erityisesti avuntarvitsijoiden ja kulkeutujien keskuudessa opintojen kulku sen sijaan hapuilee. Lukiolaisten opiskeluun kohdistuvien odotusten voidaan tämän tutkimuksen tuloksen perusteella katsoa ennustavan todellista opintojen kulkua ja opintomenestystä melko hyvin. Eroja on sekä tavoitetasossa, opiskeluprosessiin liittyvissä kokemuksissa että jatko-opintosuunnitelmissa ja ne ovat yhteydessä sukupuoleen, isän sosioekonomiseen asemaan, erikoislinjalla opiskeluun sekä lukion alun itsesäätelyryhmiin.

Teholähteet led-valaistuksessa ja sopivan valinta kotitalouskäyttöön

Led-valaisun kehitys on mahdollistanut sen käytön kodin yleisvalaistuksessa. Työssä tutkitaan eri led-valaisuun soveltuvia teholähteitä, joista valitaan teknisiltä ominaisuuksiltaan sopivin kodin yleiskäyttöön. Tutkittavia teholähteitä ovat lineaariset ja hakkuriteholähteet. Teholähteiden ominaisuuksista tarkastellaan hyötysuhteita ja tehokertoimia, joista molempien perusteella sopivin teholähdetyyppi valitaan.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.

Tekijännimet Mikael Agricolan teosten kielessä. Henkilötarkoitteisten johdosten merkitykset, funktiot ja rakenteet

My research deals with agent nouns in the language of the works of Mikael Agricola (ca. 1510–1557). The main tasks addressed in my thesis have been to describe individual agent noun types, to provide a comprehensive picture of the category of agent nouns and to clarify the relations between different types of agent nouns. My research material consists of all the agent nouns referring to persons in the language of Agricola’s works, together with their context. The language studied is for the most part translated language. Agent nouns play an important role both in the vocabulary of natural language and in broader sentence structures, since in a text it is constantly necessary to refer to actors re-ferring to persons in the text. As a concept and a phenomenon, the agent noun is widely known in languages. It is a word formed with a certain derivational affixes, which typical-ly refers to a person. In my research the agent noun category includes both deverbal and denominal derivatives referring to persons, e.g. kirjoittaa > kirjoittaja (to write > writer), asua > asuva (to inhabit > inhabitant), imeä > imeväinen (to suck > suckling), juopua > juopunut (to drink > drunkard), pelätä > pelkuri (to fear > one who fears ‘a coward’), apu > apulainen (help/to help > helper); lammas > lampuri (sheep > shepherd). Besides original Finnish expressions, agent noun derivatives taken as such from foreign languages form a word group of central importance for the research (e.g. nikkari, porvari, ryöväri, based on the German/Swedish for carpenter, burgher, robber). Especially important for the formation of agent nouns in Finnish are the models offered by foreign languages. The starting point for my work is predominantly semantic, as both the criteria for collecting the material and the categorisation underlying the analysis of the material are based on semantic criteria. When examining derivatives, aspects relating to structure are also inevitably of central importance, as form and meaning are closely associated with each other in this type of vocabulary. The alliance of structure and meaning can be described in an illustrative manner with the help of structural schemata. The examination of agent nouns comprises on the one hand analysis of syntactic elements and on the other, study of cultural words in their most typical form. The latter aspect offers a research object in which language and the extralinguistic world, referents, their designations and cultural-historical reality are in concrete terms one and the same. Thus both the agent noun types that follow the word formation principles of the Finn-ish language and those of foreign origin borrowed as a whole into Finnish illustrate very well how an expression of a certain origin and formed according to a certain structural model is inseparably bound up with the background of its referent and in general with semantic factors. This becomes evident both on the level of the connection between cer-tain linguistic features and text genre and in relation to cultural words referring to per-sons. For example, the model for the designations of God based on agent nouns goes back thousands of years and is still closely linked in 16th century literature with certain text genres. This brings out the link between the linguistic feature and the genre in a very con-crete manner. A good example of the connection between language and the extralinguistic world is provided by the cultural vocabulary referring to persons. Originally Finnish agent noun derivatives are associated with an agrarian society, while the vocabulary relat-ing to mediaeval urbanisation, the Hansa trade and specialisation by trade or profession is borrowed and originates in its entirety from vocabulary that was originally German.

Performance evaluation of hydrocyclone filter for microirrigation

In this study a hydrocyclone filter of 20 cm was selected and its performance was evaluated by studying the variation of discharge, pressure drop, influent concentration, and filtration efficiency with elapsed time of operation. The filter was tested with clean water to determine clean pressure drop and later it was tested with four concentrations of solid suspension, viz. 300; 600; 900 and 1,200 mg L-1. In the concentration of 300 mg L-1, the variation of pressure drop was low. But for the other concentrations of solid suspension, the variation was significant. The maximum pressure drops obtained were 41.19, 45.11, 50.01 and 52.95 kPa at 350, 390, 280 and 190 minutes of elapsed time, respectively. The maximum efficiency of solid suspension was 30.3, 32.96, 43.89 and 52.5% where as the minimum efficiencies were 9.91, 9.93, 9.62 and 9.9%, respectively. The hydrociclone tested presented inefficiency to filter small particles as clay. The initial removal efficiency of higher concentration was bigger than for lower concentration but, the final efficiency are almost the same irrespective of the concentration of solid suspension. The present tested hydrocyclone could be used as a pre-filter microirrigation to prevent emitter clogging.

Removal of organic matter and nutrients from slaughterhouse wastewater by using Eichhornia crassipes and evaluation of the generated biomass composting

The objective of this research was to evaluate the performance of the aquatic macrophyte Eichhornia crassipes applied in situ in a slaughter house treatment system, located in the west of the Paraná state, Brazil, regarding the nutrients removal and organic matter. Moreover, it aimed to obtain data from the production, management and composting practices of the biomass generated in the system. During 11 months of macrophytes development, physic and chemical parameters were monitored and plant density was controlled by periodical removal of excess biomass, which was weekly monitored and it is expressed in kg of aquatic plant per m² covered area. The degradation of the macrophytes removed from the treatment system was evaluated at the pilot scale in eight composting piles of 0.60 m³ that underwent four different treatments and two repetitions: T1 - water hyacinth (Eichhornia crassipes); T2 - water hyacinth and swine excrement (7:1), T3 - water hyacinth, swine excrement and earth (7:1:0,67), and T4 - water hyacinth, swine excrement and cellulosic gut (7:1:0,67), for a period of 90 days. The results indicated maximum removal efficiencies of 77.2% for COD; 77.8% for BOD, 87.9% for total nitrogen, 47.5% for ammonia nitrogen and 38.9% for total phosphorus for a five-day retention time. For biomass stabilization by composting, considering the C:N ratio as an indicator of compost maturity, it was observed that treatment T4 resulted in the shortest stabilization period (60 days). No difference was verified in the biostabilization rates at 5% level by the F test.

Metanolin tuotanto biomassasta

Tämä työ käsittelee eri tapoja, joilla biomassasta voidaan valmistaa metanolia. Työssä käydään läpi eri valmistusreitit sekä tarkastellaan biomassaa raaka-aineena. Työhön on myös koottu joidenkin maailmalla tehtyjen tutkimusten aine- ja energiataseita. Tutkimusten pohjalta mietitään onko metanolin tuotanto liikennepolttoaineeksi tällä hetkellä taloudellisesti tai energiatehokkuudeltaan järkevää. Metanolia voidaan valmistaa biomassasta pääsääntöisesti viidellä eri tavalla. Ensimmäinen tapa on kaasuttaa biomassaa, jolloin tuotetaan raaka-kaasua. Raaka-kaasusta jalostetaan synteesikaasua, josta voidaan metanolisynteesillä valmistaa metanolia. Toinen tapa metanolin valmistamiseksi on liittää tuotanto sellunkeiton yhteyteen. Tällöin raaka-aineena olisi selluprosessissa syntyvä mustalipeä, josta metanoli voidaan erottaa. Kolmas mahdollinen valmistusprosessi on biomassan mädätys. Mädätyksessä syntyy biokaasua, josta jalostetaan synteesikaasuaja siitä edelleen metanolia. Neljäs keino metanolin valmistamiseksi biomassasta on pyrolyysi. Puun pyrolyysissä puu kuumennetaan nopeasti hapettomissa tai rajallisen hapensaannin olosuhteissa. Prosessissa syntyvästä pyrolyysiöljystä voidaan erottaa metanolia tislaamalla. Viides mahdollinen reitti metanolin valmistukselle on Fischer¬–Tropsch-synteesi. Biomassasta saatu synteesikaasu johdetaan FT-synteesiin, jossa katalyyttisesti saadaan hiilivetyjen ohella tuotettua metanolia. Biopolttoaineiden kuten metanolin valmistusprosesseja tutkitaan ja kehitetään jatkuvasti, sillä uusiutumattomat energianlähteet eivät riitä loputtomasti ja niiden aiheuttamia hiilidioksidipäästöjä halutaan vähentää. Tällä hetkellä tuotantoteknologiat eivät ole vielä tarpeeksi kehittyneet, jotta tuotanto saataisiin vastaamaan kulutusta. Metanolia ei kuitenkaan vielä voida käyttää sellaisenaan liikennepolttoaineena, joten metanolin markkinat ainakin vielä ovat sillä saralla varsin kapeat.

Simulation and optimization of IGCC technique for power generation and hydrogen production by using lignite Thar coal and cotton stalk

The purpose of this study was to simulate and to optimize integrated gasification for combine cycle (IGCC) for power generation and hydrogen (H2) production by using low grade Thar lignite coal and cotton stalk. Lignite coal is abundant of moisture and ash content, the idea of addition of cotton stalk is to increase the mass of combustible material per mass of feed use for the process, to reduce the consumption of coal and to increase the cotton stalk efficiently for IGCC process. Aspen plus software is used to simulate the process with different mass ratios of coal to cotton stalk and for optimization: process efficiencies, net power generation and H2 production etc. are considered while environmental hazard emissions are optimized to acceptance level. With the addition of cotton stalk in feed, process efficiencies started to decline along with the net power production. But for H2 production, it gave positive result at start but after 40% cotton stalk addition, H2 production also started to decline. It also affects negatively on environmental hazard emissions and mass of emissions/ net power production increases linearly with the addition of cotton stalk in feed mixture. In summation with the addition of cotton stalk, overall affects seemed to negative. But the effect is more negative after 40% cotton stalk addition so it is concluded that to get maximum process efficiencies and high production less amount of cotton stalk addition in feed is preferable and the maximum level of addition is estimated to 40%. Gasification temperature should keep lower around 1140 °C and prefer technique for studied feed in IGCC is fluidized bed (ash in dry form) rather than ash slagging gasifier