Muscle damage slows oxygen uptake kinetics during moderate-intensity exercise performed at high pedal rate

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The Influence of Cutting Speed and Cutting Initiation Location in Specimen Preparation for the Microtensile Bond Strength Test

Purpose: This study evaluated the effect of cutting initiation location and cutting speed on the bond strength between resin cement and feldspathic ceramic.Materials and Methods: Thirty-six blocks (6.4 x 6.4 x 4.8 mm) of ceramic (Vita VM7) were produced. The ceramic surfaces were etched with 10% hydrofluoric acid gel for 60 s and then silanized. Each ceramic block was placed in a silicon mold with the treated surface exposed. A resin cement (Variolink II) was injected into the mold over the treated surface and polymerized. The resin cement-ceramic blocks were divided into two groups according to experimental conditions: a) cutting initiation location - resin cement, ceramic and interface; and b) cutting speed - 10,000, 15,000, and 20,000 rpm. The blocks were sectioned to achieve non-trimmed bar specimens. The microtensile test was performed in a universal testing machine (1 mm/min). The failure modes were examined using an optical light microscope and SEM. Bond strength results were analyzed using one-way ANOVA and Tukey's test (alpha = 0.05).Results: Significant influences of cutting speed and initiation location on bond strength (p < 0.05) were observed. The highest mean was achieved for specimens cut at 15,000 rpm at the interface (15.12 +/- 5.36 MPa). The lowest means were obtained for specimens cut at the highest cutting speed in resin cement (8.50 +/- 3.27 MPa), and cut at the lowest cutting speed in ceramic (8.60 +/- 2.65MPa). All groups showed mainly mixed failure (75% to 100%).Conclusion: The cutting speed and initiation location are important factors that should be considered during specimen preparation for microtensile bond strength testing, as both may influence the bond strength results.

Production of biodiesel by esterification of palmitic acid over mesoporous aluminosilicate Al-MCM-41

Biodiesel has been obtained by esterification of palmitic acid with methanol, ethanol and isopropanol in the presence of Al-MCM-41 mesoporous molecular sieves with Si/Al ratios of 8.16 and 32. The catalytic acids were synthesized at room temperature and characterized by atomic absorption spectrometry (AAS), thermal analysis (TG/DTA), X-ray diffraction (XRD), nitrogen absorption (BET/BJH), infrared spectroscopy (IR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The reaction was carried out at 130 degrees C whilst stirring at 500 rpm, with an alcohol/acid molar ratio of 60 and 0.6 wt% catalyst for 2 h. The alcohol reactivity follows the order methanol > ethanol > isopropanol. The catalyst Al-MCM-41 with ratio Si/Al = 8 produced the largest conversion values for the alcohols studied. The data followed a rather satisfactory approximation to first-order kinetics. (C) 2008 Elsevier Ltd. All rights reserved.

Determination of sulfur compounds in gasoline using mercury film electrode by square wave voltammetry

A sensitive method based on square wave voltammetry is described for the quantitative determination of elemental sulfur, disulfide and mercaptan in gasoline using a mercury film electrode. These sulfur compounds can be quantified by direct dissolution of gasoline in a supporting electrolyte followed by subsequent voltammetric measurement. The supporting electrolyte is 1.4 mol L-1 sodium acetate and No acetic acid in methanol. Chemical and optimum operational conditions for the formation of the mercury film were analyzed in this study. The values obtained were a 4.3 mu m thickness for the mercury film, a 1000 rpm rotation frequency, -0.9 V applied potential and 600 s depositing time. Voltammetric measurements were obtained using square wave voltammetry with detection limits of the 3.0 x 10(-9), 1.6 x 10(-7) and 4.9 x 10(-7) mol L-1 for elemental sulfur, disulfide and mercaptan, respectively. (C) 2007 Elsevier Ltd. All rights reserved.

Desempenho da colhedora de milho Penha CLM-350: parte II - sistemas de debulhamento e limpeza

Com a finalidade de quantificar o desempenho dos sistemas de debulhamento e limpeza da colhedora Penha CLM-350,, estudou-se as perdas percentuais era grão de milho, ocorridos na saída de palhas, bem como a porcentagem de impurezas, presente no milho ensacado. Tomando-se como 100% os grãos de milho colhidos pelo sistema espigador, determinou-se o valor percentual perdido pelos sistemas de debulhamento e limpeza, bem como a porcentagem de impurezas presente nos grãos de milho ensacado, nos diversos tratamentos estudados. O teor médio de umidade foi de 15,78% (b.u.). Os tratamentos correspondentes ao sistema de debulhamento e limpeza são as velocidades periféricas do debulhador ou as rotações do aspirador em faces da configuração geométrica da máquina. Os resultados obtidos foram estudados através da análise de variância, empregando-se os testes F, aos níveis de 1% e 5% de probabilidade e o teste Tukey, para a comparação estatística entre as médias. A análise estatística para verificar a influência da rotação do aspirador, era relação a porcentagem de grãos de milho perdidos na saída de palhas, mostrou diferenças altamente significativas, podendo-se admitir uma relação direta entre os dois parâmetros nas condições do ensaio. Com relação a rotação do aspirador e a porcentagem de impurezas, presentes nos grãos de milho ensacados, os testes das médias revelaram significância entre os tratamento D (1241,7 rpm) e E (820 rpm) sendo que este último apresentou a maior média. Uma análise mais acurada dos resultados sugere que a porcentagem de impurezas, estaria mais na dependência das relações de fluxo através da colhedora, do que propriamente do regime do aspirador.

Variabilidade espacial e controle estatístico do processo de perdas na colheita mecanizada do algodoeiro

Dentro do processo produtivo, a colheita, se mal conduzida, poderá causar prejuízos quali-quantitativos no produto final. Dessa forma, esse trabalho teve o objetivo de avaliar as perdas quantitativas, no solo e na planta, na colheita mecanizada de algodão, no ano agrícola de 2006, em Ipameri-GO, em um talhão de 1,4 ha, sendo georreferenciados 41 pontos, distanciados de 50 m no sentido da curva de nível e 9 m entre fileiras. As amostras foram coletadas colocando-se uma armação de 4,5 m² sobre o solo, coletando todo o algodão caído no solo e, em seguida, fez-se a coleta do algodão que permaneceu na planta após a passagem da colhedora. Além das perdas quantitativas determinaram-se o teor médio de água do algodão e o Rendimento Potencial Máximo (RPM). Foram construídas cartas de controle para verificar a qualidade da operação de colheita. Observou-se que as perdas na colheita do algodão foram altas, principalmente as perdas no solo (PS), indicando que a colhedora não apresentou boa eficiência de colheita. As perdas no solo não apresentaram dependência espacial, enquanto as perdas na planta e totais apresentaram dependência moderada e forte, respectivamente. O processo de colheita de algodão não se encontra dentro dos padrões de qualidade, sob o ponto de vista de controle estatístico de processo, devendo ser revistas as condições de colheita.

Tratamento de efluente de abatedouro de tilápia com adição de manipueira na fase anóxica

O objetivo deste trabalho foi avaliar a desnitrificação de efluente de abatedouro de tilápia, em reator em batelada. Para isto, foi avaliado o efluente gerado por uma indústria processadora de mandioca (manipueira) como fonte de carbono. Também foram avaliadas as condições de agitação do sistema. Os experimentos foram conduzidos em escala de laboratório, em que foram testados cinco níveis de agitação (20; 32; 60; 88 e 100 rpm) e cinco níveis de relação DQO/N (0,1; 1,0; 3,2; 5,4 e 6,3), configurando-se um planejamento do tipo Delineamento Composto Central Rotacional (DCCR), com quatro ensaios nos níveis +1 e - 1; quatro ensaios nos níveis dos pontos axiais (-1,414 e +1,414) e mais uma triplicata no ponto central (0), totalizando 11 ensaios. Avaliaram-se o desempenho da desnitrificação através da remoção de nitrato (%) e a remoção de nitrito (%). Durante o processo, também foram monitorados temperatura (ºC), pH e alcalinidade (mgCaCO3.L-1). Os resultados mostraram que a relação DQO/N teve influência significativa, com intervalo de confiança de 95%, sobre o processo de remoção de nitrato e nitrito, com faixa ótima de operação entre 3,2 e 5,4, cujas eficiências de remoção de nitrogênio foram de 100%.

Estabelecimento de condições operacionais para o bico rotativo micromax na aplicação do herbicida glyphosate

Alguns parâmetros operaciona is do bico rotativo Micromax para apli cação do herbi cida glypho sate foram estudados em condições de laboratório. O bico Micromax a 1.600 rpm e vazão de 0,96 //min forneceu gotas com vmd de 280 μm e à vazão de 0,43 i/min , de 232 μm, sendo que em ambas as condições o coeficient e de dispersão (r = vmd/nmd) foi inferior a 1,4, atendendo, portanto, às especificações para o processo CDA. A distância entre bicos a serem montadas numa barra foi determinada em mesa de estudo do padrão de deposição foi de 1,80 m para a vazão de 0,96 Z/min e concentração da formulação comercial do glyphosate entre 4% e 6%. Essa distancia foi de 1,40 m para vazão de 0,43 1/min e concentração de glyphosate entre 9% e 13%. Distancias fora dessas especificações produziram deposições bastante irregulares sob a barra de pulverização.

Efeito da concentração de fibra e parâmetros operacionais de extrusão sobre as propriedades de pasta de misturas de fécula de mandioca e polpa cítrica

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Production of fructooligosaccharides by the mycelia of Aspergillus japonicus immobilized in calcium alginate

This work describes fructose oligosaccharide (FOS) production by the immobilized mycelia (IM) of a strain of Aspergillus japonicus, isolated from soil. The microorganism was inoculated into 50 mi of medium composed of sugar cane molasses (5.0% of total sugars); yeast powder; 2.0%; K2HPO4, 0.5%; NaNO3, 0.2%; MgSO4. 7H(2)O, 0.05%; KCl, 0.05%, final pH 5.0, and the flasks were agitated in an orbital shaker at 200 rpm for 60 h, at 30 degrees C. The beta-fructofuranosidase activity (Uf), transfructosylating activity (Ut), hydrolyzing activity (Uh), and FOS production were analyzed by high performance liquid chromatography. FOS production was performed in a batch process in a 2-l jar fermenter by IM in calcium alginate beads. The optimum pH and temperature were 5.0-5.6 and 55 degrees C, respectively No loss of activity was observed when the mycelium was maintaned at 60 degrees C for 60 min. Maximum production was obtained using 5.75% (cellular weight/volume) of mycelia (122.4 Ut g(-1)) and 65% sucrose solution (w:v) for 4 h of reaction when the final product reached 61.28% of fetal FOS containing GF(2) (30.56%), GF(3) (26.45%), GF(4) (4.27%), sucrose (9.6%) and glucose (29.10%). In the assay conditions, 23 batches were performed without loss of activity of the IM, showing that the microorganism and the process utilized have potential for industrial applications. (C) 1998 Elsevier B.V. Ltd. All rights reserved.

Simultaneous determination of zinc, copper, lead, and cadmium in fuel ethanol by anodic stripping voltammetry using a glassy carbon-mercury-film electrode

A new, versatile, and simple method for quantitative analysis of zinc, copper, lead, and cadmium in fuel ethanol by anodic stripping voltammetry is described. These metals can be quantified by direct dissolution of fuel ethanol in water and subsequent voltammetric measurement after the accumulation step. A maximum limit of 20% (v/v) ethanol in water solution was obtained for voltammetric measurements without loss of sensitivity for metal species. Chemical and operational optimum conditions were analyzed in this study; the values obtained were pH 2.9, a 4.7-mum thickness mercury film, a 1,000-rpm rotation frequency of the working electrode, and a 600-s pre-concentration time. Voltammetric measurements were obtained using linear scan (LSV), differential pulse (DPV), and square wave (SWV) modes and detection limits were in the range 10(-9)-10(-8) mol L-1 for these metal species. The proposed method was compared with a traditional analytical technique, flame atomic absorption spectrometry (FAAS), for quantification of these metal species in commercial fuel ethanol samples.

Oxidation of H2S in acid solution by Thiobacillus ferrooxidans and Thiobacillus thiooxidans

Qualitative and quantitative oxidation tests of H2S in acid solution were carried out using Thiobacillus ferrooxidans and Thiobacillus thiooxidans species, Experiments were performed using solutions of H2SO4 (pH 2.0) containing H2S in initial concentrations ranging from 5 to 100 ppm. in shake flasks at 150 rpm and 30(circle)C. In these solution, this gas was not very stable and was quickly liberated. However, at low concentration (less than 5 ppm) it becomes stable and could only be removed from solution by oxidation. The results obtained indicated that the presence of either T. ferrooxidans or T. thiooxidans causes a significant reduction in H,S concentration (more than 99%) in relation to the sterile control, No differences in oxidation efficiency between these two species were detected. (C) 2001 Elsevier B.V. Ltd. All rights reserved.

Soil CO2 efflux following rotary tillage of a tropical soil

Stopping the increase of atmospheric CO2 level is an important task and information on how to implement adjustments on tillage practices could help lower Soil CO2 emissions would be helpful. We describe how rotary tiller use on a red latosol affected Soil CO2 efflux. The impact of changing blade rotation speed and rear shield position on soil CO2 efflux was investigated. Significant differences among treatments were observed up to 10 days after tillage. Cumulative CO2 efflux was as much as 40% greater when blade rotation of 216 rpm and a lowered rear shield was compared to blade rotation of 122 rpm and raised shield. This preliminary work suggests that adjusting rotary tiller settings could help reduce CO2 efflux close to that of undisturbed soil, thereby helping to conserve soil carbon in tropical environments. (C) 2004 Elsevier B.V. All rights reserved.

Effect of thermal treatment temperature on the crystallinity and morphology of LiTaO3 thin films prepared from polymeric precursor method

Lithium tantalate thin films (LiTaO3) with (50:50) stoichiometry were prepared by spin coating method using a polymeric organic solution. The films were deposited on silicon (100) substrates with 4 layers. The substrates were previously cleaned and then the solution of lithium tantalate was deposited by adjusting the speed at 5000 rpm. The thin films deposited were thermally treated from 350 to 600degreesC for 3 hours in order to study the influence of the thermal treatment temperature on the crystallinity, microstructure, grain size and roughness of the final film. X-ray diffraction (XRD) results showed that the films are polycrystalline and secondary phases free. The thickness of films was observed by scanning electron microscopy (SEM). The atomic force microscopy (AFM) studies showed that the grain size and roughness are strongly influenced by thermal treatment.

The influence of fermentation time and the presence of salts in the rheology of the fermentation broth of a polysaccharide-producing bacteria free of soil

Rheological studies were carried out in the fermentation broth of a polysaccharide-producing microorganism free of soil. This microorganism was designated 4B. The bacteria 4B was inoculated in the fermentation broth, which consisted of a carbon source and mineral salts, and it was incubated in a rotating agitator at 30 degreesC for 72 h at 210 rpm. A rheometer of concentric cylinders equipped with a thermostatic bath was used and the readings were taken at 25 degreesC. A study was made of the influence of the fermentation time and the readings were made after 24, 48 and 72 h of incubation, using, separately, sucrose and glucose as carbon sources. The influence of the salt concentrations was determined in each carbon source; the salts used were NaCl, KCl and CaCl2 in the concentrations of 0.4%, 1.0%, 2.0% and 3.0%. It was observed that the fermentation broth behaves as a non-Newtonian fluid and it presents pseudoplastic behaviour. Calculations were made of the flow behaviour index (n) and the consistency index (k) of the samples after 24, 48 and 72 h of fermentation, and it was observed that the 72 h sample presented higher k and consequently higher apparent viscosity. of the carbon sources used, the sucrose presented higher viscous broths after 24 and 48 h, and the glucose after 72 h of fermentation. With relation to the effect of the addition of salts, the CaCl2 presented a higher influence on the viscosity of the fermentation broths. (C) 2001 Elsevier B.V. Ltd. All rights reserved.