Static and Dynamic Experimental Analysis of the Galloping Stability of Porous H-Section Beams

The phenomenon of self-induced vibrations of prismatic beams in a cross-flow has been studied for decades, but it is still of great interest due to their important effects in many different industrial applications. This paper presents the experimental study developed on a prismatic beam with H-section.The aim of this analysis is to add some additional insight into the behaviour of the flow around this type of bodies, in order to reduce galloping and even to avoid it. The influence of some relevant geometrical parameters that define the H-section on the translational galloping behaviour of these beams has been analysed. Wind loads coefficients have been measured through static wind tunnel tests and the Den Hartog criterion applied to elucidate the influence of geometrical parameters on the galloping properties of the bodies under consideration.These results have been completed with surface pressure distribution measurements and, besides, dynamic tests have been also performed to verify the static criterion. Finally, the morphology of the flow past the tested bodies has been visualised by using smoke visualization techniques. Since the rectangular section beam is a limiting case of the H-section configuration, the results here obtained are compared with the ones published in the literature concerning rectangular configurations; the agreement is satisfactory.

Comportamiento hidrológico de cuencas de media montaña españolas: efectos de los procesos de acumulación / fusión de nieve en terrenos permeables sobre la infiltración y régimen de caudales Alto Tajo

La infiltración de agua en el suelo y la recarga profunda del agua subterránea contenida en los acuíferos es un proceso lento en relación con otros fenómenos hidrológicos. La redacción de esta tesis ha pretendido contribuir al estudio de la influencia que el almacenamiento de la precipitación sólida en forma de manto de nieve y su eventual fusión puedan tener sobre dicho proceso en áreas de media montaña (1.000 – 2.000 m.) en las que con gran frecuencia se sitúan las cabeceras de los ríos peninsulares. Para ello se ha partido del análisis de las diferentes variables intervinientes durante un determinado periodo temporal y sobre un espacio geográfico concreto, por lo que su metodología es de naturaleza empírica. La extensión del periodo (2002/03 a 2010/11) ha venido condicionada por la disponibilidad de los valores de algunas de sus principales variables, como han sido el equivalente en agua de la nieve acumulada y los caudales procedentes de su fusión. Éstos se han obtenido como resultado de la aplicación del modelo ASTER, desarrollado en el programa de Evaluación de los Recursos Hídricos procedentes de la Innivación (ERHIN), calibrado – entre otros- con datos de precipitaciones, temperatura y caudales provenientes a su vez del Sistema Automático de Información Hidrológica (SAIH). Ambos programas fueron implantados por la Administración en las diferentes Confederaciones Hidrográficas y en determinados Organismos de cuenca actuales, en cuyo desarrollo participó el autor de esta tesis. En cuanto a la zona de estudio se ha procedido a su elección considerando las posibles áreas de media montaña en las que la presencia de la nieve fuera hidrológicamente significativa y estuvieran constituidas litológicamente por afloramientos permeables que no impidieran la infiltración en el terreno y la formación de acuíferos de cierta relevancia. El interés se centró discrecionalmente en la cuenca del Tajo, tanto por el carácter estratégico de la misma -como suministradora en la actualidad de excedentes a otras cuencas deficitarias- como por el valor representativo de sus condiciones climáticas y orográficas en relación con otras cuencas hidrográficas peninsulares. Para ello se partió de las cabeceras de ríos identificadas por el programa ERHIN por su interés nivológico para la implantación del modelo ASTER y de las Masas de Agua Subterráneas MASb (antes Unidades Hidrogeológicas UUHH) definidas en los planes hidrológicos. La intersección en el territorio de ambos criterios condujo, finalmente, a la zona del Alto Tajo, en la que se cumplen ambos requisitos. El tramo quedó concretado en el comprendido entre las cabeceras de los ríos Tajo y Guadiela y la cola de los embalses de Entrepeñas y Buendía respectivamente, puntos de cierre para la calibración llevada a cabo en la modelización ASTER. Gran parte de éste discurre, en su parte alta, sobre rocas carbonatadas (calizas y dolomías del Jurásico y Cretácico), relacionados con las MASb de Tajuña-Montes Universales, Molina de Aragón y Sigüenza-Maranchón. Los valores diarios de las reservas de agua en forma de nieve, evapotranspiración y caudales procedentes de la fusión se han obtenido a partir de los resultados del mencionado modelo, procediéndose al cálculo de la infiltración por balance hídrico durante el periodo de estudio considerado, teniendo en cuenta los valores de precipitación, evapotranspiración y aportaciones de caudales. Esto ha requerido el estudio previo de las condiciones hidrogeológicas de la zona seleccionada con objeto de conocer las posibles interconexiones subterráneas que pudieran alterar los saldos entre las variables intervinientes anteriormente citadas. Para ello se ha llevado a cabo la recopilación y análisis de la información hidrogeológica correspondiente a la documentación de los planes hidrológicos del Tajo (Plan Hidrológico de la cuenca del Tajo RD 1664/1998 y el actual Plan Hidrológico de la parte española de la Demarcación Hidrográfica del Tajo RD 270/2014) y de los estudios previos realizados por el organismo de cuenca y el Instituto Geológico y Minero de España (lGME) fundamentalmente. En relación con la MASb Tajuña-Montes Universales -cuya extensión supera la zona seleccionada- dichos estudios consideran su estructura geológica y distribución litológica, con intercalaciones impermeables que actúan como barreras, dividiendo a éstas en Subunidades e identificando las zonas de drenaje de sus respectivos acuíferos. También se ha considerado la documentación y estudios previos del Plan Hidrológico Nacional sobre las Unidades Hidrogeológicas compartidas entre ámbitos geográficos de diferentes planes hidrológicos. Se concluye que las divisorias hidrográficas de las cabeceras son sensiblemente coincidentes o abarcan las Subunidades Montes Universales meridionales, Priego, Cifuentes, Zaorejas, u Montes Universales septentrionales, que drenan hacia el Tajo/Guadiela (bien directamente, bien a través de afluentes como el Gallo, Ablanquejo, Cabrillas, Cuervo…), MASb Molina de Aragón, que drena al Tajo a través del río Gallo y MASb Sigüenza—Maranchón, que drena su parte correspondiente hacia el Tajo a través del Ablanquejo. Se descartan – salvo la pequeña salvedad del manantial de Cifuentes- las conexiones hidrogeológicas con otras MASb o Subunidades por lo que las cabeceras del Tajo y del Guadiela pueden considerarse como un Sistema independiente donde las precipitaciones no evaporadas escurren superficialmente o se infiltran y descargan hacia los embalses de Entrepeñas y Buendía. La cuantificación diaria y acumulada de los balances hídricos ha permitido calcular la evolución aproximada de las reservas de agua subterránea desde la fecha inicial. Originalmente los balances se realizaron de forma separada en las cabeceras del Tajo y del Guadiela, cuyos valores acumulados manifestaron una tendencia creciente en la primera y decreciente en la segunda. Dicha situación se equilibra cuando el balance se practica conjuntamente en ambas, apreciándose en la variación del volumen de agua subterránea una evolución acorde hidrológicamente con los ciclos de verano/invierno y periodos de sequía, manteniéndose sus valores medios a largo/medio plazo, poniendo en evidencia la existencia de interconexiones subterráneas entre ambas cuencas. El balance conjunto, agregando la cabecera del Tajuña (que también comparte los materiales permeables de la MASb Tajuña-Montes Universales) no reveló la existencia de nuevas interrelaciones hidrogeológicas que influyeran en los balances hídricos realizados Tajo/Guadiela, confirmando las conclusiones de los estudios hidrogeológicos anteriormente analizados. Se ha procedido a confrontar y validar los resultados obtenidos de la evolución de las reservas de agua subterránea mediante los siguientes procedimientos alternativos: - Cálculo de los parámetros de desagüe de la curva de agotamiento correspondiente al volumen de agua subterránea drenante hacia el Tajo/Guadiela. Éste se ha realizado a partir de las aportaciones mensuales entrantes en los embalses de Entrepeñas y Buendía durante los meses de junio, julio, agosto y septiembre, cuyos valores responden al perfil típico de descargas de un acuífero. A partir de éstos se ha determinado el volumen drenante correspondiente al primero de junio de cada año de la serie histórica considerada. - Determinación del caudal base por el método Wallingford y deducción de los volúmenes drenantes. Estimación de las recarga anuales - Cuantificación de la recarga anual por el método Sanz, Menéndez Pidal de Navascués y Távara. Se obtuvieron valores de recarga muy aproximados entre los calculados por los dos últimos procedimientos citados. Respecto a las reservas de agua subterránea almacenadas siguen una evolución semejante en todos los casos, lo que ha permitido considerar válidos los resultados conseguidos mediante balance hídrico. Confirmada su solidez, se han buscado correlaciones simples entre el volumen de las reservas subterráneas (como indicador estimativo del efecto de la infiltración) y los volúmenes procedentes de la fusión. La conclusión es que estos últimos no tienen un efecto determinante a escala anual sobre la infiltración,recarga y variación de los volúmenes de agua subterránea, frente al peso de otras variables (precipitación y evapotranspiración). No obstante se ha encontrado una buena correlación múltiple entre la recarga estimada y la precipitación eficaz (precipitación menos evapotranspiración) y fusión, que ha permitido cuantificar la contribución de esta última. Posteriormente se ha recurrido a la selección de los episodios más intensos de acumulación /fusión en las cabeceras del Tajo y Guadiela. Y se procedió a la comparación entre los resultados obtenidos por aplicación del modelo de simulación en los mismos periodos (normalmente de varios días de duración) con datos reales y con datos ficticios de temperatura que anularan o disminuyeran la presencia de nieve, apreciándose una gran sensibilidad del efecto de la temperatura sobre la evapotranspiración y estableciéndose nuevamente correlaciones lineales entre los volúmenes de fusión y el incremento de reservas subterráneas. Las mismas confirman el efecto “favorecedor” de la acumulación de agua en forma de nieve y su posterior licuación, sobre sobre la infiltración de agua en el suelo y almacenamiento subterráneo. Finalmente se establecieron varios escenarios climáticos (+1ºC; +3ºC; +1ºC y – 10% precipitación; y 3ºC – 10% precipitación) compatibles con las previsiones del IPCC para mediados y finales del presente siglo, determinándose mediante simulación ASTER los correspondientes valores de fusión. La correlación establecida a escala anual ha permitido evaluar el efecto de la disminución del volumen de fusión - en los diferentes escenarios – sobre la recarga, pronosticando un descenso de los caudales de estiaje y la desaparición del “efecto nieve” sobre la infiltración y recarga con un aumento de 3ºC de temperatura. Teniendo en cuenta las condiciones de representatividad de la zona elegida, resulta verosímil la extensión de las anteriores conclusiones a otras cabeceras fluviales enclavadas en áreas de media montaña situadas entre 1000 a 2000m y sus efectos aguas abajo.Water infiltration into the soil and groundwater recharge deep water in aquifers is slow relative to other hydrological phenomena. The wording of this thesis aims to contribute to the study of the influence that the storage of solid precipitation as snow cover and its eventual melting may have on this process in mid-mountain areas (1000 - 2,000 m) where very often the headwaters of the peninsular rivers are located. For this party analysis of the different variables involved has over a given time period and a particular geographical area, so that their methodology is empirical in nature. The extension of the period (2002/03 to 2010/11) has been conditioned by the availability of the values of some of its key variables, as were the water equivalent of the snow and flows from melting. These have been obtained as a result of the application of ASTER model, developed in the program Evaluation of Water Resources from the Innivation (ERHIN), calibrated - among others data of rainfall, temperature and flow from turn System Automatic Hydrological Information (SAIH). Both programs were implemented by the Administration in the different Water Boards and to undertakings for current basin, in which the author participated development of this thesis. As for the study area has proceeded at its option considering the possible areas of midmountain in the presence of snow outside hydrological meaningful and they were lithology consisting of permeable outcrops that did not prevent infiltration into the ground and forming aquifers of some significance. We were interested discretion in the Tagus basin, therefore the strategic nature of it, as currently supplying surplus to other basins deficit- as the representative value of its climate and terrain conditions in relation to other peninsular river basins . To do this we started from the headwaters identified by the ERHIN program for its implementation snow interest to the ASTER model and Ground Water Bodies MASb (before UUHH Hydrogeological Units) defined in hydrological plans. The intersection in the territory of both criteria led eventually to the Alto Tajo, in which both requirements are met. The section was finalized in the period between the headwaters of the Tagus and Guadiela rivers and reservoirs end Entrepeñas and Buendia respectively checking points for calibration performed in ASTER modeling. Much of it runs on carbonate rocks (limestones and dolomites of Jurassic and Cretaceous) related MASb of Tajuña -Montes Universal, Molina de Aragón and Sigüenza-Maranchón. The daily values of water reserves in the form of snow, evapotranspiration and flow from melting were obtained from the results of this model, proceeding to the calculation of infiltration water balance during the study period considered, taking into account values of precipitation, evapotranspiration and input flow. This has required the prior examination of the hydrogeological conditions of your required in order to know the possible underground interconnections that could alter the balance between the intervening variables aforementioned area. For this we have carried out the collection and analysis of hydrogeological information relevant documentation Tagus river management plans (Hydrological Plan Tajo Basin RD 1664/1998 and the current Hydrological Plan of the Spanish part of the River Basin Tagus RD 270/2014) and previous studies by the basin organization and the Geological Survey of Spain (IGME) mainly. Regarding the MASb Tajuña- Montes Universal - whose length exceeds the area selected - these studies consider its geological structure and lithology distribution with waterproof collations that act as barriers, dividing it into subunits and identifying areas draining their respective aquifers. It has also considered the documentation and previous studies of the National Hydrological Plan on shared among different geographical areas management plans Hydrogeological Units. We conclude that river dividing the headers are substantially coincident or covering Subunits southern Universal Montes, Priego Cifuentes, Zaorejas and northern Universal Mounts, which drain into the Tagus / Guadiela (either directly or through tributaries such as Gallo, Ablanquejo , whitecaps , Raven ...), MASb Molina de Aragón which drains through the Tajo del Gallo and MASb Sigüenza- Maranchón river that drains into the Tagus using the Ablanquejo . Discarded - except the small exception of spring Cifuentes -hydrogeological connections with other MASb or Subunits so the headwaters of the Tagus and Guadiela be considered as a separate system, where rainfall not evaporated runs on surface or infiltrates and eventually discharged into reservoirs Entrepeñas and Buendia. The daily and cumulative quantification of water balances allowed us to compute the approximate evolution of groundwater reserves from its initial date. Initially balances were performed separately in the headwaters of the Tagus and Guadiela, whose cumulative values showed an increasing trend in the first and decreasing in the second. This situation is balanced when the balance is practiced together in both , appreciating the change in volume of groundwater hydrological evolution commensurate with the cycles of summer / winter and drought periods , keeping their average long / medium term values and putting in shows the existence of underground interconnections between the two basins. The overall balance, adding header Tajuña (which also shares the permeable materials MASb Tajuña -Montes Universal ) did not reveal the existence of new hydrogeological interrelationships that influenced water balances made Tajo / Guadiela, confirming the findings of the hydrogeological studies previously analyzed. We proceeded to confront and validate the results of the evolution of groundwater reserves by the following alternative procedures: - Calculate the parameters drain depletion curve corresponding to the volume of groundwater draining into the Tajo / Guadiela. This has been made from monthly inflows in the reservoirs of Entrepeñas and Buendia during the months of June, July, August and September, whose values match the typical profile of an aquifer discharges. From these has been determined for the first of June each year of the time series considered drainage volume - Determination of base flow by Wallingford method and deduction of drainage volumes. Estimate of annual recharge - Quantification of the annual recharge by the method Sanz Menéndez Pidal of Navascués and Távara. Very approximate values recharge between calculated for the last two mentioned methods were obtained. Concerning groundwater reserves stored follow a similar pattern in all cases, allowing consider valid the results achieved through water balance. Confirmed its robustness, simple correlations were sought between the volume of groundwater reserves (as estimated indicator of the effect of infiltration) and volumes from the melting. The conclusion is that the latter do not have a decisive effect on the annual scale infiltration, recharge and variation in volumes of groundwater, against the weight of other variables (precipitation and evapotranspiration). However found a good multiple correlation between the estimated recharge and effective precipitation (precipitation minus evapotranspiration) and fusion, which allowed quantify the contribution of the latter. Subsequently it has resorted to the selection of the most intense episodes of accumulation / melting in the headwaters of the Tagus and Guadiela. And we proceeded to the comparison between the results obtained by application of the simulation model in the same periods (usually several days) with real data and fictitious temperature data to annul or decrease the presence of snow, appreciating a great sensitivity of the effect of temperature on evapotranspiration and establishing linear correlations between the volumes of melting and increased groundwater reserves again. They confirm the “flattering " effect of water accumulation as snow and subsequent liquefaction of the infiltration of water into the soil and underground storage. Finally various climate scenarios (+1ºC; +3ºC; +1ºC y – 10% precipitation; y 3ºC – 10% precipitation) were established consistent with IPCC projections for mid - to late - century, determined through simulation ASTER corresponding values of melting. The correlation established on an annual scale has allowed to evaluate the effect of decreasing the volume of melt - in different scenarios - on recharge, predicting a decline in low flows and the disappearance of "snow effect" on infiltration and recharge with an increase of 3°C temperature. Given the conditions of representativeness of the chosen area, plausible extension of the above findings to other landlocked headwaters in mid-mountain areas located between 1000 to 2000m and its downstream effects.

Hydrodynamic forces on heave plates for offshore systems oscillating close to the seabed or the free surface

La energía eólica marina es uno de los recursos energéticos con mayor proyección pudiendo contribuir a reducir el consumo de combustibles fósiles y a cubrir la demanda de energía en todo el mundo. El concepto de aerogenerador marino está basado en estructuras fijas como jackets o en plataformas flotantes, ya sea una semisumergible o una TLP. Se espera que la energía eólica offshore juegue un papel importante en el perfil de producción energética de los próximos años; por tanto, las turbinas eólicas deben hacerse más fables y rentables para ser competitivas frente a otras fuentes de energía. Las estructuras flotantes pueden experimentar movimientos resonantes en estados de la mar con largos períodos de oleaje. Estos movimientos disminuyen su operatividad y pueden causar daños en los componentes eléctricos de las turbinas y en las palas, también en los risers y moorings. La respuesta de la componente vertical del movimiento puede reducirse mediante diferentes actuaciones: (1) aumentando la amortiguación del sistema, (2) manteniendo el período del movimiento vertical fuera del rango de la energía de la ola, y (3) reduciendo las fuerzas de excitación verticales. Un ejemplo típico para llevar a cabo esta reducción son las "Heave Plates". Las heave plates son placas que se utilizan en la industria offshore debido a sus características hidrodinámicas, ya que aumentan la masa añadida y la amortiguación del sistema. En un análisis hidrodinámico convencional, se considera una estructura sometida a un oleaje con determinadas características y se evalúan las cargas lineales usando la teoría potencial. El amortiguamiento viscoso, que juega un papel crucial en la respuesta en resonancia del sistema, es un dato de entrada para el análisis. La tesis se centra principalmente en la predicción del amortiguamiento viscoso y de la masa añadida de las heave plates usadas en las turbinas eólicas flotantes. En los cálculos, las fuerzas hidrodinámicas se han obtenido con el f n de estudiar cómo los coeficientes hidrodinámicos de masa añadida5 y amortiguamiento varían con el número de KC, que caracteriza la amplitud del movimiento respecto al diámetro del disco. Por otra parte, se ha investigado la influencia de la distancia media de la ‘heave plate’ a la superficie libre o al fondo del mar, sobre los coeficientes hidrodinámicos. En este proceso, un nuevo modelo que describe el trabajo realizado por la amortiguación en función de la enstrofía, es descrito en el presente documento. Este nuevo enfoque es capaz de proporcionar una correlación directa entre el desprendimiento local de vorticidad y la fuerza de amortiguación global. El análisis también incluye el estudio de los efectos de la geometría de la heave plate, y examina la sensibilidad de los coeficientes hidrodinámicos al incluir porosidad en ésta. Un diseño novedoso de una heave plate, basado en la teoría fractal, también fue analizado experimentalmente y comparado con datos experimentales obtenidos por otros autores. Para la resolución de las ecuaciones de Navier Stokes se ha usado un solver basado en el método de volúmenes finitos. El solver usa las librerías de OpenFOAM (Open source Field Operation And Manipulation), para resolver un problema multifásico e incompresible, usando la técnica VOF (volume of fluid) que permite capturar el movimiento de la superficie libre. Los resultados numéricos han sido comparados con resultados experimentales llevados a cabo en el Canal del Ensayos Hidrodinámicos (CEHINAV) de la Universidad Politécnica de Madrid y en el Canal de Experiencias Hidrodinámicas (CEHIPAR) en Madrid, al igual que con otros experimentos realizados en la Escuela de Ingeniería Mecánica de la Universidad de Western Australia. Los principales resultados se presentan a continuación: 1. Para pequeños valores de KC, los coeficientes hidrodinámicos de masa añadida y amortiguamiento incrementan su valor a medida que el disco se aproxima al fondo marino. Para los casos cuando el disco oscila cerca de la superficie libre, la dependencia de los coeficientes hidrodinámicos es más fuerte por la influencia del movimiento de la superficie libre. 2. Los casos analizados muestran la existencia de un valor crítico de KC, donde la tendencia de los coeficientes hidrodinámicos se ve alterada. Dicho valor crítico depende de la distancia al fondo marino o a la superficie libre. 3. El comportamiento físico del flujo, para valores de KC cercanos a su valor crítico ha sido estudiado mediante el análisis del campo de vorticidad. 4. Introducir porosidad al disco, reduce la masa añadida para los valores de KC estudiados, pero se ha encontrado que la porosidad incrementa el valor del coeficiente de amortiguamiento cuando se incrementa la amplitud del movimiento, logrando un máximo de damping para un disco con 10% de porosidad. 5. Los resultados numéricos y experimentales para los discos con faldón, muestran que usar este tipo de geometrías incrementa la masa añadida cuando se compara con el disco sólido, pero reduce considerablemente el coeficiente de amortiguamiento. 6. Un diseño novedoso de heave plate basado en la teoría fractal ha sido experimentalmente estudiado a diferentes calados y comparado con datos experimentales obtenidos por otro autores. Los resultados muestran un comportamiento incierto de los coeficientes y por tanto este diseño debería ser estudiado más a fondo. ABSTRACT Offshore wind energy is one of the promising resources which can reduce the fossil fuel energy consumption and cover worldwide energy demands. Offshore wind turbine concepts are based on either a fixed structure as a jacket or a floating offshore platform like a semisubmersible, spar or tension leg platform. Floating offshore wind turbines have the potential to be an important part of the energy production profile in the coming years. In order to accomplish this wind integration, these wind turbines need to be made more reliable and cost efficient to be competitive with other sources of energy. Floating offshore artifacts, such oil rings and wind turbines, may experience resonant heave motions in sea states with long peak periods. These heave resonances may increase the system downtime and cause damage on the system components and as well as on risers and mooring systems. The heave resonant response may be reduced by different means: (1) increasing the damping of the system, (2) keeping the natural heave period outside the range of the wave energy, and (3) reducing the heave excitation forces. A typical example to accomplish this reduction are “Heave Plates”. Heave plates are used in the offshore industry due to their hydrodynamic characteristics, i.e., increased added mass and damping. Conventional offshore hydrodynamic analysis considers a structure in waves, and evaluates the linear and nonlinear loads using potential theory. Viscous damping, which is expected to play a crucial role in the resonant response, is an empirical input to the analysis, and is not explicitly calculated. The present research has been mainly focused on the prediction of viscous damping and added mass of floating offshore wind turbine heave plates. In the calculations, the hydrodynamic forces have been measured in order to compute how the hydrodynamic coefficients of added mass1 and damping vary with the KC number, which characterises the amplitude of heave motion relative to the diameter of the disc. In addition, the influence on the hydrodynamic coefficients when the heave plate is oscillating close to the free surface or the seabed has been investigated. In this process, a new model describing the work done by damping in terms of the flow enstrophy, is described herein. This new approach is able to provide a direct correlation between the local vortex shedding processes and the global damping force. The analysis also includes the study of different edges geometry, and examines the sensitivity of the damping and added mass coefficients to the porosity of the plate. A novel porous heave plate based on fractal theory has also been proposed, tested experimentally and compared with experimental data obtained by other authors for plates with similar porosity. A numerical solver of Navier Stokes equations, based on the finite volume technique has been applied. It uses the open-source libraries of OpenFOAM (Open source Field Operation And Manipulation), to solve 2 incompressible, isothermal immiscible fluids using a VOF (volume of fluid) phase-fraction based interface capturing approach, with optional mesh motion and mesh topology changes including adaptive re-meshing. Numerical results have been compared with experiments conducted at Technical University of Madrid (CEHINAV) and CEHIPAR model basins in Madrid and with others performed at School of Mechanical Engineering in The University of Western Australia. A brief summary of main results are presented below: 1. At low KC numbers, a systematic increase in added mass and damping, corresponding to an increase in the seabed proximity, is observed. Specifically, for the cases when the heave plate is oscillating closer to the free surface, the dependence of the hydrodynamic coefficients is strongly influenced by the free surface. 2. As seen in experiments, a critical KC, where the linear trend of the hydrodynamic coefficients with KC is disrupted and that depends on the seabed or free surface distance, has been found. 3. The physical behavior of the flow around the critical KC has been explained through an analysis of the flow vorticity field. 4. The porosity of the heave plates reduces the added mass for the studied porosity at all KC numbers, but the porous heave plates are found to increase the damping coefficient with increasing amplitude of oscillation, achieving a maximum damping coefficient for the heave plate with 10% porosity in the entire KC range. 5. Another concept taken into account in this work has been the heave plates with flaps. Numerical and experimental results show that using discs with flaps will increase added mass when compared to the plain plate but may also significantly reduce damping. 6. A novel heave plate design based on fractal theory has tested experimentally for different submergences and compared with experimental data obtained by other authors for porous plates. Results show an unclear behavior in the coefficients and should be studied further. Future work is necessary in order to address a series of open questions focusing on 3D effects, optimization of the heave plates shapes, etc.

The representation of the world in national Arab news agencies: an exploration of (trans)national networks in the official Arab media

The purpose of this paper is to draw a map of the representation of the world and of Arab states as reflected by the countries of the region. To do so, we have analysed the news (4,093 news randomly collected on February and August 2005) produced by the governments of the Arab states through their national news agencies. Several regional and world maps had been constructed to show the official Arab representation of the World, the Arab countries conflict agenda, the persistence of colonial ties (with the European metropolis) and the emergence of new relationships (Asian countries). The representation of the world that appeared in the analysis focuses its interest on the USA, the war in Iraq, the Israel-Palestine conflict, the United Kingdom, France, and Iran. The Arab regional powers organise the flow of information (Saudi Arabia and Egypt) and the colonial past determines the current structure of communication (French-speaking bloc and English-speaking bloc).

Electrooxidation methods to produce pseudocapacitance-containing porous carbons

Surface oxygen groups play a key role on the performance of porous carbon electrodes for electrochemical capacitors in aqueous media. The electrooxidation method in NaCl electrolyte using a filter press cell and dimensionally stable anodes is proposed as a viable process for the generation of oxygen groups on porous carbon materials. The experimental set-up is so flexible that allows the easy modification of carbon materials with different configurations, i.e. cloths and granular, obtaining different degrees of oxidation for both conformations without the requirement of binders and conductivity promoters. After the electrooxidation method, the attained porosity is maintained between 90 and 75% of the initial values. The surface oxygen groups generated can increase the capacitance up to a 30% when compared to the pristine material. However, a severe oxidation is detrimental since it may decrease the conductivity and increase the resistance for ion mobility.

Structural and photoelectrochemical properties of porous TiO2 nanofibers decorated with Fe2O3 by sol-flame

The hybrid structure of Fe2O3 nanoparticles/TiO2 nanofibers (NFs), combines the merits of large surface areas of TiO2 NFs and absorption in ultraviolet light–visible light range. This structure can be used for many applications such as photoelectrochemical water splitting and photo-catalysis. Here, a sol-flame method is used for depositing Fe2O3 on TiO2 NFs that were prepared by hydrothermal on Ti sheets. The obtained materials were characterized by XRD, SEM, UV/Vis diffuse reflectance, Raman, and XPS. The results revealed the formation of rutile and anatase crystalline phases together with Fe2O3. This process moves the absorption threshold of TiO2 NFs support into visible spectrum range and enhances the photocurrent in comparison to bare TiO2 NFs, although no hole scavenger was used. The impedance measurement at low and high frequencies revealed an increase in series resistance and a decrease in resistance of charge transfer with sol-flame treatment time. A mechanism for explaining the charge transfer in these TiO2 NFs decorated with Fe2O3 nanoparticles was proposed.

Electrochemical Performance of Hierarchical Porous Carbon Materials Obtained from the Infiltration of Lignin into Zeolite Templates

Hierarchical porous carbon materials prepared by the direct carbonization of lignin/zeolite mixtures and the subsequent basic etching of the inorganic template have been electrochemically characterized in acidic media. These lignin-based templated carbons have interesting surface chemistry features, such as a variety of surface oxygen groups and also pyridone and pyridinic groups, which results in a high capacitance enhancement compared to petroleum-pitch-based carbons obtained by the same procedure. Furthermore, they are easily electro-oxidized in a sulfuric acid electrolyte under positive polarization to produce a large amount of surface oxygen groups that boosts the pseudocapacitance. The lignin-based templated carbons showed a specific capacitance as high as 250 F g−1 at 50 mA g−1, with a capacitance retention of 50 % and volumetric capacitance of 75 F cm−3 at current densities higher than 20 A g−1 thanks to their suitable porous texture. These results indicate the potential use of inexpensive biomass byproducts, such as lignin, as carbon precursors in the production of hierarchical carbon materials for electrodes in electrochemical capacitors.

(Table 1) Summary of basalt unit thickness, vesicularity, number of flow units, and average porosity at ODP Site 135-839

An inflatable drill-string packer was used at Site 839 to measure the bulk in-situ permeability within basalts cored in Hole 839B. The packer was inflated at two depths, 398.2 and 326.9 mbsf; all on-board information indicated that the packer mechanically closed off the borehole, although apparently the packer hydraulically sealed the borehole only at 398.2 mbsf. Two pulse tests were run at each depth, two constant-rate injection tests were run at the first set, and four were run at the second. Of these, only the constant-rate injection tests at the first set yielded a permeability, calculated as ranging from 1 to 5 * 10**-12 m**2. Pulse tests and constant-rate injection tests for the second set did not yield valid data. The measured permeability is an upper limit; if the packer leaked during the experiments, the basalt would be less permeable. In comparison, permeabilities measured at other Deep Sea Drilling Project and Ocean Drilling Program sites in pillow basalts and flows similar to those measured in Hole 839B are mainly about 10**-13 to 10**-14 m**2. Thus, if our results are valid, the basalts at Site 839 are more permeable than ocean-floor basalts investigated elsewhere. Based on other supporting evidence, we consider these results to be a valid measure of the permeability of the basalts. Temperature data and the geochemical and geotechnical properties of the drilled sediments all indicate that the site is strongly affected by fluid flow. The heat flow is very much less than expected in young oceanic basalts, probably a result of rapid fluid circulation through the crust. The geochemistry of pore fluids is similar to that of seawater, indicating seawater flow through the sediments, and sediments are uniformly underconsolidated for their burial depth, again indicating probable fluid flow. The basalts are highly vesicular. However, the vesicularity can only account for part of the average porosity measured on the neutron porosity well log; the remainder of the measured porosity is likely present as voids and fractures within and between thin-bedded basalts. Core samples, together with porosity, density, and resistivity well-log data show locations where the basalt section is thin bedded and probably has from 15% to 35% void and fracture porosity. Thus, the measured permeability seems reasonable with respect to the high measured porosity. Much of the fluid flow at Site 839 could be directed through highly porous and permeable zones within and between the basalt flows and in the sediment layer just above the basalt. Thus, the permeability measurements give an indication of where and how fluid flow may occur within the oceanic crust of the Lau Basin.

Coding and flow charting as applied to UICSM programed texts (1962-1963 versions) /

Project No. 711151.01.

Spray drier simulation and air flow pattern studies

The literature pertaining to the key stages of spray drying has been reviewed in the context of the mathematical modelling of drier performance. A critical review is also presented of previous spray drying models. A new mathematical model has been developed for prediction of spray drier performance. This is applicable to slurries of rigid, porous crust-forming materials to predict trajectories and drying profiles for droplets with a distribution of sizes sprayed from a centrifugal pressure nozzle. The model has been validated by comparing model predictions to experimental data from a pilot-scale counter-current drier and from a full-scale co-current drier. For the latter, the computed product moisture content was within 2%, and the computed air exit temperature within 10oC of experimental data. Air flow patterns have been investigated in a 1.2m diameter transparent countercurrent spray tower by flow visualisation. Smoke was introduced into various zones within the tower to trace the direction, and gauge the intensity, of the air flow. By means of a set of variable-angle air inlet nozzles, a variety of air entry configurations was investigated. The existence of a core of high rotational and axial velocity channelling up the axis of the tower was confirmed. The stability of flow within the core was found to be strongly dependent upon the air entry arrangement. A probe was developed for the measurement of air temperature and humidity profiles. This was employed for studying evaporation of pure water drops in a 1.2m diameter pilot-scale counter-current drier. A rapid approach to the exit air properties was detected within a 1m distance from the air entry ports. Measured radial profiles were found to be virtually flat but, from the axial profiles, the existence of plug-flow, well-mixed-flow and some degree of air short-circuiting can be inferred. The model and conclusions should assist in the improved design and optimum operation of industrial spray driers.

The steady performance of a porous and compliant aerostatic thrust bearing

Recent developments in aerostatic thrust bearings have included: (a) the porous aerostatic thrust bearing containing a porous pad and (b) the inherently compensated compliant surface aerostatic thrust bearing containing a thin elastomer layer. Both these developments have been reported to improve the bearing load capacity compared to conventional aerostatic thrust bearings with rigid surfaces. This development is carried one stage further in a porous and compliant aerostatic thrust bearing incorporating both a porous pad and an opposing compliant surface. The thin elastomer layer forming the compliant surface is bonded to a rigid backing and is of a soft rubber like material. Such a bearing is studied experimentally and theoretically under steady state operating conditions. A mathematical model is presented to predict the bearing performance. In this model is a simplified solution to the elasticity equations for deflections of the compliant surface. Account is also taken of deflections in the porous pad due to the pressure difference across its thickness. The lubrication equations for flow in the porous pad and bearing clearance are solved by numerical finite difference methods. An iteration procedure is used to couple deflections of the compliant surface and porous pad with solutions to the lubrication equations. Comparisons between experimental results and theoretically predicted bearing performance are in good agreement. However these results show that the porous and compliant aerostatic thrust bearing performance is lower than that of a porous aerostatic thrust bearing with a rigid surface in place of the compliant surface. This discovery is accounted to the recess formed in the bearing clearance by deflections of the compliant surface and its effect on flow through the porous pad.