Heating self-interaction mechanism of surface magnetoplasma waves in plasma-like medium bounded by metal

The influence of electron heating in the high-frequency surface magnetoplasma wave(SM) field on dispersion properties of the considered SM is investigated. High frequency SM propagate at the interface between a plasma like medium with a finite electrons pressure and a metal. The nonlinear dispersion relation for the SM is derived and investigated.

CFD simulations of flow and heat transfer through the porous interface of a metal foam heat exchanger

This paper offers numerical modelling of a waste heat recovery system. A thin layer of metal foam is attached to a cold plate to absorb heat from hot gases leaving the system. The heat transferred from the exhaust gas is then transferred to a cold liquid flowing in a secondary loop. Two different foam PPI (Pores Per Inch) values are examined over a range of fluid velocities. Numerical results are then compared to both experimental data and theoretical results available in the literature. Challenges in getting the simulation results to match those of the experiments are addressed and discussed in detail. In particular, interface boundary conditions specified between a porous layer and a fluid layer are investigated. While physically one expects much lower fluid velocity in the pores compared to that of free flow, capturing this sharp gradient at the interface can add to the difficulties of numerical simulation. The existing models in the literature are modified by considering the pressure gradient inside and outside the foam. Comparisons against the numerical modelling are presented. Finally, based on experimentally-validated numerical results, thermo-hydraulic performance of foam heat exchangers as waste heat recovery units is discussed with the main goal of reducing the excess pressure drop and maximising the amount of heat that can be recovered from the hot gas stream.

Biolistic transformation of elite indica rice (Oryza sativa L.) cultivars through semi-solid and liquid medium selection systems

Following microprojectile mediated delivery of a plasmid construct (pAHC-25) encoding bar (bialophos resistance) gene into five-day-old scutellar calli derived from mature embryos, the effectiveness of selection procedure for bar-gene expressing tissue was compared for two indica rice cultivars (IR-64 and Karnal Local). While IR-64 transformants could be selected through the generally used semi-solid selection medium, the same procedure was not effective in the basmati cultivar Karnal Local. In the latter case, while lower concentrations (2–4 mg 1−1) of the selective agent phosphinothricin (PPT) yielded only escapes, higher concentrations (6–8 mg l−1) inhibited proliferation of transformed as well as untransformed sectors. For Karnal Local, a liquid medium based selection system was successfully utilized for recovering transformed sectors and, eventually, regenerants. The study demonstrates the generation of transformants of two elite indica cultivars using the environment-independent system of mature embryos from seeds.

A comparative study of the proliferation and osteogenic differentiation of human periodontal ligament cells cultured on β-TCP ceramics and demineralized bone matrix with or without osteogenic inducers in vitro

The repair of bone defects that result from periodontal diseases remains a clinical challenge for periodontal therapy. β-tricalcium phosphate (β-TCP) ceramics are biodegradable inorganic bone substitutes with inorganic components that are similar to those of bone. Demineralized bone matrix (DBM) is an acid-extracted organic matrix derived from bone sources that consists of the collagen and matrix proteins of bone. A few studies have documented the effects of DBM on the proliferation and osteogenic differentiation of human periodontal ligament cells (hPDLCs). The aim of the present study was to investigate the effects of inorganic and organic elements of bone on the proliferation and osteogenic differentiation of hPDLCs using three-dimensional porous β-TCP ceramics and DBM with or without osteogenic inducers. Primary hPDLCs were isolated from human periodontal ligaments. The proliferation of the hPDLCs on the scaffolds in the growth culture medium was examined using a Cell‑Counting kit‑8 (CCK-8) and scanning electron microscopy (SEM). Alkaline phosphatase (ALP) activity and the osteogenic differentiation of the hPDLCs cultured on the β-TCP ceramics and DBM were examined in both the growth culture medium and osteogenic culture medium. Specific osteogenic differentiation markers were examined using reverse transcription-quantitative polymerase chain reaction (RT-qPCR). SEM images revealed that the cells on the β-TCP were spindle-shaped and much more spread out compared with the cells on the DBM surfaces. There were no significant differences observed in cell proliferation between the β-TCP ceramics and the DBM scaffolds. Compared with the cells that were cultured on β-TCP ceramics, the ALP activity, as well as the Runx2 and osteocalcin (OCN) mRNA levels in the hPDLCs cultured on DBM were significantly enhanced both in the growth culture medium and the osteogenic culture medium. The organic elements of bone may exhibit greater osteogenic differentiation effects on hPDLCs than the inorganic elements.

Knowledge management challenges in small-and medium-sized enterprises

Background & Research Focus Managing knowledge for innovation and organisational benefit has been extensively investigated in studies of large firms (Smith, Collins & Clark, 2005; Zucker, et al., 2007) and to a large extent there is limited research into studies of small- and medium- sized enterprises (SMEs). There are some investigations in knowledge management research on SMEs, but what remains to be seen in particular is the question of where are the potential challenges for managing knowledge more effectively within these firms? Effective knowledge management (KM) processes and systems lead to improved performance in pursuing distinct capabilities that contribute to firm-level innovation (Nassim 2009; Zucker et al. 2007; Verona and Ravasi 2003). Managing internal and external knowledge in a way that links it closely to the innovation process can assist the creation and implementation of new products and services. KM is particularly important in knowledge intensive firms where the knowledge requirements are highly specialized, diverse and often emergent. However, to a large extent the KM processes of small firms that are often the source of new knowledge and an important element of the value networks of larger companies have not been closely studied. To address this gap which is of increasing importance with the growing number of small firms, we need to further investigate knowledge management processes and the ways that firms find, capture, apply and integrate knowledge from multiple sources for their innovation process. This study builds on the previous literature and applies existing frameworks and takes the process and activity view of knowledge management as a starting point of departure (see among others Kraaijenbrink, Wijnhoven & Groen, 2007; Enberg, Lindkvist, & Tell, 2006; Lu, Wang & Mao, 2007). In this paper, it is attempted to develop a better understanding of the challenges of knowledge management within the innovation process in small knowledge-oriented firms. The paper aims to explore knowledge management processes and practices in firms that are engaged in the new product/service development programs. Consistent with the exploratory character of the study, the research question is: How is knowledge integrated, sourced and recombined from internal and external sources for innovation and new product development? Research Method The research took an exploratory case study approach and developed a theoretical framework to investigate the knowledge situation of knowledge-intensive firms. Equipped with the conceptual foundation, the research adopted a multiple case study method investigating four diverse Australian knowledge-intensive firms from IT, biotechnology, nanotechnology and biochemistry industries. The multiple case study method allowed us to document in some depth the knowledge management experience of the theses firms. Case study data were collected through a review of company published data and semi-structured interviews with managers using an interview guide to ensure uniform coverage of the research themes. This interview guide was developed following development of the framework and a review of the methodologies and issues covered by similar studies in other countries and used some questions common to these studies. It was framed to gather data around knowledge management activity within the business, focusing on the identification, acquisition and utilisation of knowledge, but collecting a range of information about subject as well. The focus of the case studies was on the use of external and internal knowledge to support their knowledge intensive products and services. Key Findings Firstly a conceptual and strategic knowledge management framework has been developed. The knowledge determinants are related to the nature of knowledge, organisational context, and mechanism of the linkages between internal and external knowledge. Overall, a number of key observations derived from this study, which demonstrated the challenges of managing knowledge and how important KM is as a management tool for innovation process in knowledge-oriented firms. To summarise, findings suggest that knowledge management process in these firms is very much project focused and not embedded within the overall organisational routines and mainly based on ad hoc and informal processes. Our findings highlighted lack of formal knowledge management process within our sampled firms. This point to the need for more specialised capabilities in knowledge management for these firms. We observed a need for an effective knowledge transfer support system which is required to facilitate knowledge sharing and particularly capturing and transferring tacit knowledge from one team members to another. In sum, our findings indicate that building effective and adaptive IT systems to manage and share knowledge in the firm is one of the biggest challenges for these small firms. Also, there is little explicit strategy in small knowledge-intensive firms that is targeted at systematic KM either at the strategic or operational level. Therefore, a strategic approach to managing knowledge for innovation as well as leadership and management are essential to achieving effective KM. In particular, research findings demonstrate that gathering tacit knowledge, internal and external to the organization, and applying processes to ensure the availability of knowledge for innovation teams, drives down the risks and cost of innovation. KM activities and tools, such as KM systems, environmental scanning, benchmarking, intranets, firm-wide databases and communities of practice to acquire knowledge and to make it accessible, were elements of KM. Practical Implications The case study method that used in this study provides practical insight into the knowledge management process within Australian knowledge-intensive firms. It also provides useful lessons which can be used by other firms in managing the knowledge more effectively in the innovation process. The findings would be helpful for small firms that may be searching for a practical method for managing and integrating their specialised knowledge. Using the results of this exploratory study and to address the challenges of knowledge management, this study proposes five practices that are discussed in the paper for managing knowledge more efficiently to improve innovation: (1) Knowledge-based firms must be strategic in knowledge management processes for innovation, (2) Leadership and management should encourage various practices for knowledge management, (3) Capturing and sharing tacit knowledge is critical and should be managed, (4)Team knowledge integration practices should be developed, (5) Knowledge management and integration through communication networks, and technology systems should be encouraged and strengthen. In sum, the main managerial contribution of the paper is the recognition of knowledge determinants and processes, and their effects on the effective knowledge management within firm. This may serve as a useful benchmark in the strategic planning of the firm as it utilises new and specialised knowledge.

Synthesis, characterization and activity of an immobilized photocatalyst : natural porous diatomite supported titania nanoparticles

Diatomite, a porous non-metal mineral, was used as support to prepare TiO2/diatomite composites by a modified sol–gel method. The as-prepared composites were calcined at temperatures ranging from 450 to 950 _C. The characterization tests included X-ray powder diffraction (XRD), scanning electron microscopy (SEM) with an energy-dispersive X-ray spectrometer (EDS), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption/desorption measurements. The XRD analysis indicated that the binary mixtures of anatase and rutile exist in the composites. The morphology analysis confirmed the TiO2 particles were uniformly immobilized on the surface of diatom with a strong interfacial anchoring strength, which leads to few drain of photocatalytic components during practical applications. In further XPS studies of hybrid catalyst, we found the evidence of the presence of Ti–O–Si bond and increased percentage of surface hydroxyl. In addition, the adsorption capacity and photocatalytic activity of synthesized TiO2/diatomite composites were evaluated by studying the degradation kinetics of aqueous Rhodamine B under UV-light irradiation. The photocatalytic degradation was found to follow pseudo-first order kinetics according to the Langmuir–Hinshelwood model. The preferable removal efficiency was observed in composites by 750 _C calcination, which is attributed to a relatively appropriate anatase/rutile mixing ratio of 90/10.

Small and medium enterprises using software as a service : exploring the different roles of intermediaries

Software as a Service (SaaS) can provide significant benefits to small and medium enterprises (SMEs) due to advantages like ease of access, 7*24 availability, and utility pricing. However, underlying the SaaS delivery model is often the assumption that SMEs will directly interact with the SaaS vendor and use a self-service approach. In practice, we see the rise of SaaS intermediaries who can support SMEs with sourcing and leveraging SaaS. This paper reports on the roles of intermediaries and how they support SMEs with using SaaS. We conducted an empirical study of two SaaS intermediaries and analysed their business models, in particular their value propositions. We identified orientation (technology or customer) and alignment (operational or strategic) as themes for understanding their roles. The contributions of this paper include: (1) the identification and description of SaaS intermediaries for SMEs based on an empirical study and (2) understanding the different roles of SaaS intermediaries, in particular a more basic role based on technology orientation and operational alignment and a more value adding role based on customer orientation and strategic alignment. We propose that SaaS intermediaries can address SaaS adoption and implementation challenges of SMEs by playing a basic role and can also aim to support SMEs in creating business value with SaaS based solutions by playing an added value role.

Multiphase porous media model for heat and mass transfer during drying of agricultural products

Modelling of food processing is complex because it involves sophisticated material and transport phenomena. Most of the agricultural products such fruits and vegetables are hygroscopic porous media containing free water, bound water, gas and solid matrix. Considering all phase in modelling is still not developed. In this article, a comprehensive porous media model for drying has been developed considering bound water, free water separately, as well as water vapour and air. Free water transport was considered as diffusion, pressure driven and evaporation. Bound water assumed to be converted to free water due to concentration difference and also can diffuse. Binary diffusion between water vapour and air was considered. Since, the model is fundamental physics based it can be applied to any drying applications and other food processing where heat and mass transfer takes place in porous media with significant evaporation and other phase change.

Porous versus porthole fuel injection in a radical farming scramjet: A numerical analysis

Numerically computed engine performance of a nominally two-dimensional radical farming scramjet with porous (permeable C/C ceramic) and porthole fuel injection is presented. Inflow conditions with Mach number, stagnation pressure, and enthalpy of 6.44, 40.2MPa, and 4.31 MJ/kg respectively, and fuel/air equivalence ratio of 0.44 were maintained, along with engine geometry. Hydrogen fuel was injected at an axial location of 92.33mm downstream of the leading edge for each investigated injection method. Results from this study show that porous fuel injection results in enhanced mixing and combustion compared to porthole fuel injection. This is particularly evident within the first half of the combustion chamber where porous fuel injection resulted in mixing and combustion efficiencies of 76% and 63% respectively. At the same location, porthole fuel injection resulted in efficiencies respectively of 58% and 46%. Key mechanisms contributing to the observed improved performance were the formation of an attached oblique fuel injection shock and associated stronger shock-expansion train ingested by the engine, enhanced spreading of the fuel in all directions and a more rapidly growing mixing layer.

Porous fuel injection with oxygen enrichment in a viable scramjet engine

Oxygen enriched, porous fuel injection has been numerically investigated in this study with the aim of understanding mixing and combustion enhancements achievable in a viable scramjet engine. Four injection configurations were studied: a fuel only case, a pre-mixed case and two staged injection cases where fuel and oxidiser were injected independently. All simulations were performed on a flight scale vehicle at Mach 8 flow conditions. Results show that the addition of oxygen with the fuel increases the mixing efficiency of the engine, however, is less sensitive to the method of oxygen addition: premixed versus staged. When the fuel-oxidiser-air mixture was allowed to combust, the method of additional oxygen delivery had a more significant impact. For pre-mixed fuel and oxidiser, the engine was found to choke, whereas in contrast, in the staged enrichment cases the engine failed to ignite. This result indicates that there exists an optimised configuration between pre-mixed and staged oxygen enrichment which results in a started, and combusting engine.

Numerical investigation of upstream fuel injection through porous media for scramjet engines via surrogate-assisted evolutionary algorithms

A multi-objective design optimization study has been conducted for upstream fuel injection through porous media applied to the first ramp of a two-dimensional scramjet intake. The optimization has been performed by coupling evolutionary algorithms assisted by surrogate modeling and computational fluid dynamics with respect to three design criteria, that is, the maximization of the absolute mixing quantity, total pressure saving, and fuel penetration. A distinct Pareto optimal front has been obtained, highlighting the counteracting behavior of the total pressure against the mixing efficiency and fuel penetration. The injector location and size have been identified as the key design parameters as a result of a sensitivity analysis, with negligible influence of the porous properties in the configurations and conditions considered in the present study. Flowfield visualization has revealed the underlying physics associated with the effects of these dominant parameters on the shock structure and intensity.

Natural free convection in porous media: First field documentation in groundwater

Natural free convection is a process of great importance in disciplines from hydrology to meteorology, oceanography, planetary sciences, and economic geology, and for applications in carbon sequestration and nuclear waste disposal. It has been studied for over a century - but almost exclusively in theoretical and laboratory settings, Despite its importance, conclusive primary evidence of free convection in porous media does not currently exist in a natural field setting. Here, we present recent electrical resistivity measurements from a sabkha aquifer near Abu Dhabi, United Arab Emirates, where large density inversions exist. The geophysical images from this site provide, for the first time, compelling field evidence of fingering associated with natural free convection in groundwater.