Biomassakattilan simulointi

Tässä diplomityössä mallinnetaan Apros-simulointiohjelmistolla kylläistä höyryä tuottava KPA Uniconin toimittama Biograte-kattilalaitos. Työ on rajattu käsittelemään vesihöyrypiiri syöttövesisäiliöstä prosessiin lähtevään höyryyn saakka. Savukaasupuoli on mallinnettu polttoaineen ja palamisilman syötöstä savupiippuun asti, mutta savukaasujen puhdistus on jätetty pois simulaatiomallista. Työssä kerrotaan yleisesti biopolttoaineista, kattilalaitoksista ja tulipesäratkaisuista. Simuloitava kattilalaitos ja sen säätöjärjestelmä käydään läpi yksityiskohtaisemmin. Simuloinnista ja sen mahdollisuuksista kerrotaan yleisesti, jonka jälkeen esitellään tehty simulaatiomalli. Simulointituloksia verrataan kattilan mitoitusarvoihin ja tärkeimpien prosessisuureiden muutoksia tutkitaan kuormanmuutostilanteissa. Lopuksi tuloksista tehdään yhteenveto ja esitellään jatkotoimenpidesuunnitelmat. Simuloitu kattilalaitos tuottaa kylläistä höyryä halutun määrän oikeassa paineessa ja lämpötilassa. Kattilan prosessisuureet vastaavat melko hyvin mitoitusarvoja ja simulaatiomalli toimii vakaasti myös kuormanmuutostilanteissa. Suurimmat kompromissit ja yksinkertaistukset on tehty tulipesän ja polttoaineensyötön mallinnuksessa. Näitä osa-alueita kehittämällä simulaation tarkkuutta olisi mahdollista parantaa entisestään. Jatkossa simulointimallia on tarkoitus kehittää laajentamalla se kattamaan myös laitoksen sekundääripuoli kokonaisuudessaan. Tulosten perusteella simulaatiota voidaan pitää onnistuneena mallina Biograte-kattilalaitoksesta.

Drying soybean seed using air ambient temperature at low relative humidity

Under subtropical and tropical environments soybean seed (Glycine max (L.) Merrill) are harvested early to avoid deterioration from weathering. Careful after-harvest drying is required and is an important step in maintaining the physiological quality of the seed. Soybean seed should be harvested when the moisture content is in a range of 16-20%. Traditional drying utilizes a high temperature air stream passed through the seed mass without dehumidification. The drying time is long because the system is inefficient and the high temperature increases the risk of thermal damage to the seed. New technology identified as heat pipe technology (HPT) is available and has the unique feature of removing the moisture from the air stream before it is passed through the seed mass at the same environmental temperature. Two studies were conducted to evaluate the performance of HPT for dry soybean seed. In the first study the seeds were dried from 17.5 to 11.1% in 2 hours and 29 minutes and in the second sudy the seeds were dried from 22.6 to 11.9% in 16 hours and 32 minutes. This drying process caused no reduction in seed quality as measured by the standard germination, tetrazolium-viability, accelerated aging and seedling vigor classification tests. The only parameter that indicated a slight seed quality reduction was tetrazolium vigor in the second study. It was concluded that the HPT system is a promising technology for drying soybean seed when efficiency and maintenance of physiological quality are desired.

Drying peanut seed using air ambient temperature at low relative humidity

The moisture content of peanut kernel (Arachis hypogaea L.) at digging ranges from 30 to 50% on a wet basis (w.b.). The seed moisture content must be reduced to 10.5% or below before seeds can be graded and marketed. After digging, peanuts are cured on a window sill for two to five days then mechanically separated from the vine. Heated air is used to further dry the peanuts from approximately 18 to 10% moisture content w.b. Drying is required to maintain peanut seed and grain quality. Traditional dryers pass a high temperature and high humidity air stream through the seed mass. The drying time is long because the system is inefficient and the high temperature increases the risk of thermal damage to the kernels. New technology identified as heat pipe technology (HPT) is available and has the unique feature of removing the moisture from the air stream before it is heated and passed through the seed. A study was conducted to evaluate the performance of the HPT system in drying peanut seed. The seeds inside the shells were dried from 17.4 to 7.3% in 14 hours and 11 minutes, with a rate of moisture removal of 0.71% mc per hour. This drying process caused no reduction in seed quality as measured by the standard germination, accelerated ageing and field emergence tests. It was concluded that the HPT system is a promising technology for drying peanut seed when efficiency and maintenance of physiological quality are desired.

Voimalaitosten kattilaputkien sisäpuolisten kerrostumien paksuuden mittaaminen ultraäänimenetelmällä

Höyryvoimalaitoksen käyttöönotossa muodostuu kattilaputkien sisäpinnoille niitä korroosiolta suojaava ohut metallioksidikerros. Tämän kerroksen päälle kasvaa kattilan käytön aikana haitallista kerrostumaa paikallisen korroosion tai kattilavedessä olevien epäpuhtauksien kerääntymisen tai kiteytymisen seurauksena. Kerrostuma haittaa lämmönsiirtoa tulipesästä putkiseinämän läpi kattilaveteen. Putkien lämpötilan nousu suunniteltua korkeammaksi kasvattaa putkivaurioiden ja sisäpuolisen korroosion riskiä. Tästä johtuen paksuksi kasvaneet kerrostumat pyritään poistamaan happokäsittelyllä eli peittauksella ennen vaurioiden syntyä. Perinteisesti kerrostumapaksuus on määritetty kattilasta irrotetuista näyteputkista mikroskoopilla. Työn tavoitteena oli tutkia uudenlaisen ultraäänimittauksen teoriaa ja selvittää sen toimivuus höyrystinputkien kerrostumapaksuusmittauksissa. Lisäksi tavoitteena oli tutkia voimalaitoksen höyrystimen sisäpuolisten kerrostumien muodostumista ja niiden vaikutuksia sekä kattilan peittaustarpeen arviointia. Höyrystimen kerrostumien kasvunopeuteen vaikuttavat eniten voimalaitostyyppi, käytetty vesikemia ja kattilaveteen kulkeutuvien epäpuhtauksien määrä. Kasvunopeus vaihtelee laitosten välillä suuresti ja eroaa myös tulipesän eri kohdissa. Kattilaveden epäpuhtauspitoisuus ja kerrostumapaksuus vaikuttavat molemmat korroosiovaurioiden todennäköisyyteen. Peittauspaksuuden ohjearvoissa tulisi huomioida kattilan käyttöpaine, kattilatyyppi ja riski kattilaveden laadun heikkenemiselle. Putkinäytteistä ja laitoksilla suoritettujen mittauksien perusteella uusi ultraäänitekniikka tuottaa luotettavia tuloksia tavanomaisten kerrostumien mittauksessa. Vain yhdellä laitoksella esiintyi irtonaisen sakan kaltaista kerrostumaa, jota mittaus ei kyennyt havaitsemaan. Mittaustulokset kerrostumista tulipesän eri osissa antavat hyvän perustan peittaustarpeen arviointiin.

Thermal modelling of commercial lithium-ion batteries

The accelerating adoption of electrical technologies in vehicles over the recent years has led to an increase in the research on electrochemical energy storage systems, which are among the key elements in these technologies. The application of electrochemical energy storage systems for instance in hybrid electrical vehicles (HEVs) or hybrid mobile working machines allows tolerating high power peaks, leading to an opportunity to downsize the internal combustion engine and reduce fuel consumption, and therefore, CO2 and other emissions. Further, the application of electrochemical energy storage systems provides an option of kinetic and potential energy recuperation. Presently, the lithium-ion (Li-ion) battery is considered the most suitable electrochemical energy storage type in HEVs and hybrid mobile working machines. However, the intensive operating cycle produces high heat losses in the Li-ion battery, which increase its operating temperature. The Li-ion battery operation at high temperatures accelerates the ageing of the battery, and in the worst case, may lead to a thermal runaway and fire. Therefore, an appropriate Li-ion battery cooling system should be provided for the temperature control in applications such as HEVs and mobile working machines. In this doctoral dissertation, methods are presented to set up a thermal model of a single Li-ion cell and a more complex battery module, which can be used if full information about the battery chemistry is not available. In addition, a non-destructive method is developed for the cell thermal characterization, which allows to measure the thermal parameters at different states of charge and in different points of cell surface. The proposed models and the cell thermal characterization method have been verified by experimental measurements. The minimization of high thermal non-uniformity, which was detected in the pouch cell during its operation with a high C-rate current, was analysed by applying a simplified pouch cell 3D thermal model. In the analysis, heat pipes were incorporated into the pouch cell cooling system, and an optimization algorithm was generated for the estimation of the optimalplacement of heat pipes in the pouch cell cooling system. An analysis of the application of heat pipes to the pouch cell cooling system shows that heat pipes significantly decrease the temperature non-uniformity on the cell surface, and therefore, heat pipes were recommended for the enhancement of the pouch cell cooling system.

Movax Oy:n tuotteiden ja tekniikan käyttömahdollisuudet pilaantuneiden maa-alueiden ja pohjavesien kunnostushankkeissa

Työn tavoitteena on tarkastella erilaisia in-situ -kunnostusmenetelmiä maaperän ja pohjaveden kunnostushankkeissa ja niiden toteutusvaihtoehtoja sekä vertailla niitä keskenään. Työssä tarkastellaan myös lainsäädännön ja eri menetelmien kehittymistä, niiden tulevaisuuden näkymiä sekä pohditaan yrityksen tuotteiden liiketoimintamahdollisuuksia tämän pohjalta. Tietoa kerätään kirjallisuudesta sekä tapaustutkimuksista ja niitä peilataan yrityksen sisällä olevaan hiljaiseen tietoon. Löydettyä kirjallisuustietoa sekä tapaustutkimuksia on analysoitu SWOT-analyysien sekä ryhmittelyjen avulla. Työn tuloksena on esitetty vaihtoehtoinen tapa asentaa reaktiivinen seinämä pohjaveden kunnostushankkeissa yrityksen tuotteiden ja putkipaalujen avulla. Lisäksi työn pohjalta voidaan koota materiaalia ja lisätietoa asiakkaille sekä myynnin ja markkinoinnin tukemiseen. Tulosten pohjalta voidaan arvioida, että kyseinen menetelmä tukisi myös kestävän kehityksen periaatteita kunnostushankkeen toteutus- ja asennusvaiheessa. Menetelmän avulla voitaisiin mahdollisesti vähentää reaktiivisten seinämien asentamiseen liittyviä ympäristövaikutuksia.

Sediment genotoxicity and its relationship to the frequency of chironomid labial plate deformities

Sediment samples were taken from seven locations in the WeIland River in December 1986 and April 1987. The DMSO extracts of these sediment samples showed a significant (ppipe (station D-l) . It was concluded that genotoxic contaminants were associated with the sediments from this l ocation. Analysis of sediment samples from the nearby station D-2 resulted in a significant (p <0 . 05) positive genotoxic response in December but not in April. Chironomids (midge larvae) taken from each of seven study locations were analyzed for the frequency of chironomid labial plate deformities (over 1000 individual specimens were observed) . The samples from station D-l showed the highest frequency of chironomid labial plate deformities (10 . 9% ± 3.2%), while samples from the upstream control (station A) displayed t,he lowest frequency of deformities (3.8% ± 1.3%). All samples were coded to avoid unconscious biases . The results of the genotoxicity study indicated that station D-l in the WeIland River was contaminated with genotoxic materials. The genotoxic materials may have induced the observed increased frequency in chironomid labial plate deformities . Samples from stations C and D-l, located in a downstream portion of the river bounded by an industrialized area were slightly toxic according to -the alkaline phosphatase inhib_ii~ion component of the 50S chromotest analyses. The toxicity of these samples was only evident once they had been activated by the 59 (liver extract) mixture.

Buried Treasure: The Economics of Leak Detection and Water Loss Prevention in Ontario

On average approximately 13% of the water that is withdrawn by Canadian municipal water suppliers is lost before it reaches final users. This is an important topic for several reasons: water losses cost money, losses force water agencies to draw more water from lakes and streams thereby putting more stress on aquatic ecosystems, leaks reduce system reliability, leaks may contribute to future pipe failures, and leaks may allow contaminants to enter water systems thereby reducing water quality and threatening the health of water users. Some benefits of leak detection fall outside water agencies’ accounting purview (e.g. reduced health risks to households connected to public water supply systems) and, as a result, may not be considered adequately in water agency decision-making. Because of the regulatory environment in which Canadian water agencies operate, some of these benefits-especially those external to the agency or those that may accrue to the agency in future time periods- may not be fully counted when agencies decide on leak detection efforts. Our analysis suggests potential reforms to promote increased efforts for leak detection: adoption of a Canada-wide goal of universal water metering; development of full-cost accounting and, pricing for water supplies; and co-operation amongst the provinces to promulgate standards for leak detection efforts and provide incentives to promote improved efficiency and rational investment decision-making.

Notebook with H.K. Woodruff written on the front cover

Notebook with H.K. Woodruff written on the front cover (soft cover). Inside, there is a list of 48 diverse items which include: sword found at Lundy’s Lane, stuffed frog from Long Point, Indian pipe, 5 curious old revolutionary pistols and Mrs. S. Bull’s slippers. At the back of the book there is a list of 22 items including: proclamation issued by Sir Isaac Brock on Feb. 24, 1812 and Egyptian mummy, 1884-1885.

Niagara Falls Handbill Collection, 1838-1886, n.d. (non-inclusive)

According to legend, the Burning Springs were discovered by early natives in the Niagara Peninsula. Bridgewater Mills was built on the site of the spring. During the excavation of the factory; workmen uncovered the spring. Samuel Street and Thomas Clark recognized the potential of this as a tourist attraction so they built a wooden shelter over the spring. The spring was covered with a barrel with a pipe protruding from it. This became the first tourist attraction at Niagara. The Cave of the Winds was a cavern located behind the Bridal Veil Fall. It was originally named the Aeolus Cave. In 1920, a sudden rock fall from the ceiling killed 3 tourists. The cave was destroyed in 1955 as it was deemed dangerous. The captain of the Maid of the Mist was usually a farmer who owned the land where the ship docked. In 1846, the first steam powered Maid of the Mist was launched. By 1848, the first suspension bridge was built over the gorge and the main purpose of the Maid of the Mist was no longer to carry people who needed to travel, but now the focus was on people who wanted to view the Falls at close range. Source: http://www.niagarafrontier.com/burningsprings.html http://www.niagarafrontier.com/winds.html http://reservationsystems.com/niagara_daredevils/maid_of_the_mist.html

Letter to S.D. Woodruff from A. Jeffrey importer of Hardware, Iron, Steel, and Window Glass of St. Catharines, Ont.

Letter to S.D. Woodruff from A. Jeffrey importer of Hardware, Iron, Steel, and Window Glass of St. Catharines, Ont. A. Jeffrey says that he will be able to supply Mr. Woodruff with glass and iron pipe, June 7, 1875.

Receipt from Chatfield and Neelon, Specialties, Steamboat Work and Engineers’ Supplies, St. Catharines

Receipt from Chatfield and Neelon, Specialties, Steamboat Work and Engineers’ Supplies, St. Catharines for various fittings, March 31, 1887.

Development of Free Space Method for Material Characterisation and GPR Study & A Case Study on Biological Samples

The thesis mainly focuses on material characterization in different environments: freely available samples taken in planar fonn, biological samples available in small quantities and buried objects.Free space method, finds many applications in the fields of industry, medicine and communication. As it is a non-contact method, it can be employed for monitoring the electrical properties of materials moving through a conveyor belt in real time. Also, measurement on such systems at high temperature is possible. NID theory can be applied to the characterization of thin films. Dielectric properties of thin films deposited on any dielectric substrate can be determined. ln chemical industry, the stages of a chemical reaction can be monitored online. Online monitoring will be more efficient as it saves time and avoids risk of sample collection.Dielectric contrast is one of the main factors, which decides the detectability of a system. lt could be noted that the two dielectric objects of same dielectric constant 3.2 (s, of plastic mine) placed in a medium of dielectric constant 2.56 (er of sand) could even be detected employing the time domain analysis of the reflected signal. This type of detection finds strategic importance as it provides solution to the problem of clearance of non-metallic mines. The demining of these mines using the conventional techniques had been proved futile. The studies on the detection of voids and leakage in pipes find many applications.The determined electrical properties of tissues can be used for numerical modeling of cells, microwave imaging, SAR test etc. All these techniques need the accurate determination of dielectric constant. ln the modem world, the use of cellular and other wireless communication systems is booming up. At the same time people are concemed about the hazardous effects of microwaves on living cells. The effect is usually studied on human phantom models. The construction of the models requires the knowledge of the dielectric parameters of the various body tissues. lt is in this context that the present study gains significance. The case study on biological samples shows that the properties of normal and infected body tissues are different. Even though the change in the dielectric properties of infected samples from that of normal one may not be a clear evidence of an ailment, it is an indication of some disorder.ln medical field, the free space method may be adapted for imaging the biological samples. This method can also be used in wireless technology. Evaluation of electrical properties and attenuation of obstacles in the path of RF waves can be done using free waves. An intelligent system for controlling the power output or frequency depending on the feed back values of the attenuation may be developed.The simulation employed in GPR can be extended for the exploration of the effects due to the factors such as the different proportion of water content in the soil, the level and roughness of the soil etc on the reflected signal. This may find applications in geological explorations. ln the detection of mines, a state-of-the art technique for scanning and imaging an active mine field can be developed using GPR. The probing antenna can be attached to a robotic arm capable of three degrees of rotation and the whole detecting system can be housed in a military vehicle. In industry, a system based on the GPR principle can be developed for monitoring liquid or gas through a pipe, as pipe with and without the sample gives different reflection responses. lt may also be implemented for the online monitoring of different stages of extraction and purification of crude petroleum in a plant.Since biological samples show fluctuation in the dielectric nature with time and other physiological conditions, more investigation in this direction should be done. The infected cells at various stages of advancement and the normal cells should be analysed. The results from these comparative studies can be utilized for the detection of the onset of such diseases. Studying the properties of infected tissues at different stages, the threshold of detectability of infected cells can be determined.

" Studies on Laser induced Phatothermal Phenomena in Selected Organic Compounds and Fullerenes"

In the pre—laser era it was difficult to believe that the optical properties of a medium depend upon the intensity of the radiation incident on it. The basis for this conclusion is that the electric field strength associated with the conventional light sources used before the advent of lasers was much smaller than (103 V/cm) the field sttrengths of atomic or interatomic fields (2 107 —- 10” V/cm). The radiation with such low intensity is not able to affect atomic fields to the extent of changing optical parameters. The invention of laser in 1960 was a turning point. The high degree of coherence of the laser radiation provides high spatial concentration of optical power. With the availability of the femtosecond lasers it has become possible to get extremely high peak powers 2 1013 W/cmz). At such high fields, the relationship between electric ‘polarization P and the electric field strength E ceases to be linear and several nonlinear effects begin to occur. Nonlinear absorption, a branch of nonlinear optics, refers to the interaction between radiation and matter accompanied by absorption of more than one photon. Nonlinear absorption has acquired great importance after the invention of high power lasers. One of the objectives of the present work is to investigate the nonlinear absorption processes occurring in fullerene, selected organic solvents and laser dyes. Fullerenes and laser dyes were chosen because of their highly nonlinear behaviour. Fullerenes, the most beautiful among molecules, offer fascinating field of research owinglto their significant structural properties. As toluene, benzene and carbon disulphide are themost widely used solvents for fullerenes, it seems important to study the nonlinear properties of these liquids as well. Like fullerenes, laser dyes also possess highly delocalized 7r electrons which are responsible for their nonlinear absorption. Dye lasers were the fulfillment of an experimenter’s pipe dream - to have a laser that is easily tunable over a wide range of wavelengths. A better understandingof the photophysical properties of laser dyes can significantly enhance the development and technology of dye lasers. We studied the nonlinear absorption properties of two rhodamine dyes to have some insight into their nonlinear optical properties.

Design and Development of a Remotely Operated Underwater Multi-Robot Manipulator Controller

For the scientific and commercial utilization of Ocean resources, the role of intelligent underwater robotic systems are of great importance. Scientific activities like Marine Bio-technology, Hydrographic mapping, and commercial applications like Marine mining, Ocean energy, fishing, aquaculture, cable laying and pipe lining are a few utilization of ocean resources. As most of the deep undersea exploration are beyond the reachability of divers and also as the use of operator controlled and teleoperated Remotely Operated Vehicles (ROVs) and Diver Transport Vehicles (DTVs) turn out to be highly inefficient, it is essential to have a fully automated system capable providing stable control and communication links for the unstructured undersea environment.