Land surface hydrology in a general circulation model: global and regional fields needed for validation

For the last two decades most general circulation models (GCMs) have included some kind of surface hydrology submodel. The content of these submodels is becoming increasingly complex and realistic. It is still easy to identify defects in present treatments. Yet, to improve our ability to model the contribution of land hydrology to climate and climate change, we must be concerned not with just the surface hydrology submodel per se, but also with how it works in the overall context of the GCM.

Performance of paddy-cum-prawn culture in rainfed low land ecosystem of Sunderbans

Performance of both paddy (Var. NC 492) and prawn Penaeus monodon were assessed for two years during wet-season in rainfed lowland ecosystem with a view to study the economic viability of paddy-cum-prawn culture in the coastal saline zone of West Bengal. Both mono and dual culture of paddy and prawn were tried in the study. Fingerlings of prawn (α 35,000 haˉ¹) of 10-15 mm size were reared for about three and half months with and without fish feed. It was observed that addition of fish feed resulted in higher (57.7%) production of prawn (2.65 mg/haˉ¹) but not rice. Such increase in prawn production was 1.6 times higher when no feed was provided and 1.4 times higher when grown as sole crop. However, paddy, whether grown as mono or mixed culture, did not differ in yield significantly. In dual culture, the benefit - cost ratio was higher (6.83) when prawn was grown with feed and it was maximum (36.0) when grown without feed as sole crop. The study, therefore, indicates that paddy-cum-prawn culture under low land ecosystem of the coastal saline zone is enterprising particularly for small and marginal farmers who fear to take risk of growing prawn alone at the cost of paddy.

Behavior of bulk melt-textured YBCO single domains subjected to crossed magnetic fields

We have experimentally investigated the crossed magnetic field effects on bulk melt-processed YBCO single domains. The samples were first permanently magnetized along their c-axis and then subjected to several cycles of a transverse magnetic field parallel to the ab planes. The magnetic properties along the c and ab directions were simultaneously measured using a couple of orthogonal pick-up coils as well as a Hall probe placed against the sample surface. The effects of both sweep amplitude and polarity were investigated. Field sweeps of alternate polarities are shown to affect the decay of the c-axis magnetization much more strongly than field sweeps of unique polarity do. However, the c-axis magnetization does not show any saturation even after a large number of field sweeps. Next, a micro-Hall probe scanning system was used to measure the distribution of magnetic induction over the top surface of the single domain subjected to the same combination of magnetic fields. The results are shown to be consistent with those determined with the sensing coils and bring out the role played by geometric effects.

Discrete dislocation plasticity analysis of crack-tip fields in polycrystalline materials

Small scale yielding around a mode I crack is analysed using polycrystalline discrete dislocation plasticity. Plane strain analyses are carried out with the dislocations all of edge character and modelled as line singularities in a linear elastic material. The lattice resistance to dislocation motion, nucleation, interaction with obstacles and annihilation are incorporated through a set of constitutive rules. Grain boundaries are modelled as impenetrable to dislocations. The polycrystalline material is taken to consist of two types of square grains, one of which has a bcc-like orientation and the other an fcc-like orientation. For both orientations there are three active slip systems. Alternating rows, alternating columns and a checker-board-like arrangement of the grains is used to construct the polycrystalline materials. Consistent with the increasing yield strength of the polycrystalline material with decreasing grain size, the calculations predict a decrease in both the plastic zone size and the crack-tip opening displacement for a given applied mode I stress intensity factor. Furthermore, slip-band and kink-band formation is inhibited by all grain arrangements and, with decreasing grain size, the stress and strain distributions more closely resemble the HRR fields with the crack-tip opening approximately inversely proportional to the yield strength of the polycrystalline materials. The calculations predict a reduction in fracture toughness with decreasing grain size associated with the grain boundaries acting as effective barriers to dislocation motion.