Idealized Operation of Third-Harmonic-Peaking Class-Ef Power Amplifier with Extended Maximum Operating Frequency

A new variant of Class-EF power amplifier (PA), the so-called third-harmonic-peaking Class-EF, is presented. It inherits a soft-switching operation from the Class-E PA and a low peak switch voltage from the Class-F PA. More importantly, the new topology allows operations at higher frequencies and permits deployment of large transistors which is normally prohibited since they are always accompanied with high output capacitances. Using a simple transmission-line load network, the PA is synthesized to satisfy Class-EF impedances at fundamental frequency, third harmonic, and all even harmonics as well as to simultaneously provide an impedance matching to 50-Ω load.

Low Noise Amplifier With Integrated Balanced Antenna for 60 GHz Wireless Communications

The implementation of a dipole antenna co-designed and monolithically integrated with a low noise amplifier (LNA) on low resistivity Si substrate (20 Omega . cm) manufactured in 0.35 mu m commercial SiGe HBT process with f(T)/f(max) of 170 GHz and 250 GHz is investigated theoretically and experimentally. An air gap is introduced between the chip and a reflective ground plane, leading to substantial improvements in efficiency and gain. Moreover, conjugate matching conditions between the antenna and the LNA are exploited, enhancing power transfer between without any additional matching circuit. A prototype is fabricated and tested to validate the performance. The measured 10-dB gain of the standalone LNA is centered at 58 GHz with a die size of 0.7 mm x 0.6 mm including all pads. The simulated results showed antenna directivity of 5.1 dBi with efficiency higher than 70%. After optimization, the co-designed LNA-Antenna chip with a die size of 3 mm x 2.8 mm was characterized in anechoic chamber environment. A maximum gain of higher than 12 dB was obtained.

Can(Plan)+: Extending the Operational Semantics of the BDI Architecture to deal with Uncertain Information

The BDI architecture, where agents are modelled based on their beliefs, desires and intentions, provides a practical approach to develop large scale systems. However, it is not well suited to model complex Supervisory Control And Data Acquisition (SCADA) systems pervaded by uncertainty. In this paper we address this issue by extending the operational semantics of Can(Plan) into Can(Plan)+. We start by modelling the beliefs of an agent as a set of epistemic states where each state, possibly using a different representation, models part of the agent's beliefs. These epistemic states are stratified to make them commensurable and to reason about the uncertain beliefs of the agent. The syntax and semantics of a BDI agent are extended accordingly and we identify fragments with computationally efficient semantics. Finally, we examine how primitive actions are affected by uncertainty and we define an appropriate form of lookahead planning.

Analysis of the Second Harmonic Effect on Power Amplifier Intermodulation Products

A theoretical analysis is reported in this paper to investigate the effect that a second harmonic signal which might be present at an amplifier’s input has on generating additional intermodulation products, particularly the third-order intermodulation (IM3) products. The analysis shows that the amplitude of an extra generated IM3 component is equal to the product of the fundamental amplitude, the second harmonic amplitude, and the second order Taylor series coefficient. The effect of the second order harmonic on the IM3 is examined through a simulated example of a 2.22-GHz 10-W Class-EF amplifier whereby the IM3 levels have been reduced by 2-3 dB after employing a second harmonic termination stub at the input.

Towards generalized Doherty power amplifier design for multiband operation

This paper presents a new variant of broadband Doherty power amplifier that employs a novel output combiner. A new parameter ∝ is introduced to permit a generalized analysis of the recently reported Parallel Doherty power amplifier (PDPA),and hence offer design flexibility. The circuit prototype of the new DPA fabricated using GaN devices exhibits maximum drain efficiency of 85% at 43-dBm peak power and 63% at 6-dB backoff power (BOP). Measured drain efficiency of >60% at peak power across 500-MHz frequency range and >50% at 6-dB BOP across 480-MHz frequency range were achieved, confirming the  theoretical wideband characteristics of the new DPA.

Comprehensive numerical modelling of the performance of a second harmonic generation stage coupled with a low-gain optical parametric amplifier

We present a comprehensive model for predicting the full performance of a second harmonic generation-optical parametric amplification system that aims at enhancing the temporal contrast of laser pulses. The model simultaneously takes into account all the main parameters at play in the system such as the group velocity mismatch, the beam divergence, the spectral content, the pump depletion, and the length of the nonlinear crystals. We monitor the influence of the initial parameters of the input pulse and the interdependence of the two related non-linear processes on the performance of the system and show its optimum configuration. The influence of the initial beam divergence on the spectral and the temporal characteristics of the generated pulse is discussed. In addition, we show that using a crystal slightly longer than the optimum length and introducing small delay between the seed and the pump ensures maximum efficiency and compensates for the spectral shift in the optical parametric amplification stage in case of chirped input pulse. As an example, calculations for bandwidth transform limited and chirped pulses of sub-picosecond duration in beta barium borate crystal are presented.

Economical and operational optimization of CALB immobilization on MP1000 for amidation of olein fatty acids with ethanolamine

Dissertação de Mestrado , Engenharia Biológica, Faculdade de Engenharia de Recursos Naturais, Universidade do Algarve, 2008

Towards a hydrodynamic operational model of the Algarve coast and St. Vincent Cape

This study attempts to implement a hydrodynamic operational model which can ultimately be used for projecting oil spill dispersal patterns and also sewage, pollution and can also be used in wave forecasting. A two layer nested model was created using MOHID Water, which is powerful ocean modelling software. The first layer (father) is used to impose the boundary conditions for the second layer (son). This was repeated for two different wind dominant regimes, Easterly and Westerly winds respectively. A qualitative comparison was done between measured tidal data and the tidal output. Sea surface temperature was also qualitatively compared with the model’s results. The results from both simulations were analysed and compared to historical literature. The comparison was done at the surface layer, 100 metre depth and at 800m depth. In the surface layer the first simulation generated an upwelling event near Cape St. Vincent and within the Algarve. The second simulation generated a non-upwelling event within which the surface was flow reversed and the warm water mass was along the Algarve coastline and evening turning clockwise around Cape St. Vincent. At the 100 metre depth for both simulations, velocity vortexes were observed near Cape St. Vincent travelling northerly and southerly at various instances. At 800metre depth a strong oceanic flow was observed moving north westerly along the continental shelf.

Development of an operational tool for oil spill forecast: application to oil exposed regions

Tese de doutoramento, Ciências do Mar, da Terra e do Ambiente (Modelação), Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2014